Technique Guide. Orthopaedic Cable System. Cerclage solutions for general surgery.
|
|
- Clementine Short
- 4 years ago
- Views:
Transcription
1 Technique Guide Orthopaedic Cable System. Cerclage solutions for general surgery.
2 Table of Contents Introduction The Orthopaedic Cable System 2 Indications 4 Contraindications 4 Surgical Technique Cerclage Technique 5 Tension Band Technique Olecranon 17 Tension Band Technique Patella 23 Product Information Implants 29 Instruments 30 Set List 32 Synthes
3 The Orthopaedic Cable System Orthopaedic cable Available in 1.0 mm and 1.7 mm diameters with an (8 x 7) + (1 x 19) weave for greater flexibility and control Assemblies available in 316L stainless steel, titanium alloy,* and L605 cobalt chromium alloy with titanium crimp Compatible with all Synthes stainless steel or titanium plates and screws 1.0 mm titanium needle cable with crimp allows for easier passing of the cable when a cable passer is not used Cross-sectional view of cable 8 outer bundles of 7 strands One central bundle of 19 strands * Ti-6Al-7Nb 1.0 mm titanium needle cable with crimp 2 Synthes Orthopaedic Cable System Technique Guide
4 Cerclage positioning pins Seat directly into screw hole to maintain position of the cable relative to the plate Threaded pins thread into locking holes Pins with posts are held in place by inserting the post in a 3.2 mm pilot hole in the bone. For use with 3.5 mm and 4.5 mm DCP, LC-DCP and LCP plates Accept 1.0 mm and 1.7 mm cables Available in titanium and 316L stainless steel Available sterile only Threaded cerclage positioning pin Cerclage positioning pin with post Crimp positioning pins Combines a crimp and positioning pin into one Used to maintain the position of the cable relative to the plate May decrease incision size because the crimp sits on the plate Two sizes, to fit 5.0 mm locking or 4.5 mm LCP holes and 7.3 mm locking holes For use with 1.7 mm cable 5.0 mm available in titanium and 316L stainless steel, 7.3 mm available in stainless steel only Available sterile only 5.0 mm 7.3 mm Cerclage buttons Fit into screwhead recess to provide fixation, when a screw may not have adequate purchase May be used with unicortical screws around prostheses to provide fixation Three sizes designed to fit into 2.5 mm hex/t15, 3.5 mm hex/t25 or cannulated 4 mm hex screwhead recess Fits T25 StarDrive and 3.5 mm hex Accept 1.0 mm and 1.7 mm cables Available in titanium and 316L stainless steel Available sterile only For solid screws For cannulated screws Synthes 3
5 Indications and Contraindications Cables with Crimp For general orthopaedic trauma surgery involving the olecranon, patella, femur (including periprosthetic fractures), humerus and ankle; acromioclavicular dislocations, pelvic and acetabular fractures, prophylactic banding during total joint procedures, and temporary reduction during open reduction procedures. The 1.0 mm cable with crimp and the 1.0 mm titanium needle cable are contraindicated for use in the femur ORIF and prophylactic banding during total joint procedures. These devices are intended as single use items. Cerclage Positioning Pin The cerclage positioning pin is intended for use with cerclage monofilament wire and multifilament cable to augment fracture stabilization with plates used in long bone fixation when the use of screws is contrainidicated, as in the presence of intramedullary implants. The cerclage positioning pin is designed for use in dynamic compression screw holes that accept 3.5 mm or 5.4 mm bone screws. The cerclage positioning pin (and cerclage wire or cable) can be used with a variety of Synthes plates Hex Button The hex button device is indicated for fractures that may not be securely held by either a screw or a cerclage device alone. The hex button device is intended for use where wire, cable, or band cerclage is used in combination with bone screws and/or plates, of the same material type to provide internal fixation of fractured bone. 5.0 mm and 7.3 mm Crimp Positioning Pins The 5.0 mm and 7.3 mm crimp positioning pins are intended for use with multifilament cable to augment fracture stabilization with plates used in long bone fixation when the use of screws is contraindicated, as in the presence of intramedullary implants. The 5.0 mm crimp positioning pins are designed for use in the 5.0 mm locking or 4.5 mm LCP holes of Synthes plates. The 7.3 mm crimp positioning pins are designed for use in the 7.3 mm locking holes of Synthes plates. Trochanteric Reattachment Device The trochanteric reattachment device is indicated for the reattachment of the greater trochanter following osteotomy in total hip anthroplasty, or following fracture of the greater trochanter. 4 Synthes Orthopaedic Cable System Technique Guide
6 Cerclage Technique 1 Pass cable Instruments Medium Cable Passer, curved Large Cable Passer, curved Medium Cable Passer Medium Cable Passer, 45 angle Large Cable Passer Large Cable Passer, 45 angle Figure 1 Select the appropriate cable passer. The size and shape of the cable passer selected is dependent upon the circumference of the bone and access to the site. Shaft hole Select a cable passer that will allow passage of the instrument around the bone without causing significant damage to soft tissues or excessive stripping of the periosteum. Place the cable passer around the bone (Figure 1). Thread the free end of the cable into the end hole of the cable passer until the cable exits through the shaft hole (Figure 2). End hole Remove the cable passer leaving the cable wrapped around the bone (Figure 3). Figure 2 Note: Do not thread the cable into the shaft hole of the cable passer since the cable crimp (attached to the other end of the cable) will prevent release of the cable passer. Figure 3 Synthes 5
7 Cerclage Technique continued 2 Position cable crimp Insert the free end of the cable into the open hole in the cable crimp and place the crimp in the desired position on the bone. The location for the crimp must allow adequate soft tissue coverage and ensure that the crimp remains fixed on the bone. Ensure that the points on the under surface of the cable crimp are in contact with the bone the smooth surface should be facing up. 6 Synthes Orthopaedic Cable System Technique Guide
8 3 Tension cable Instruments Cable Tensioner Attachment Bit Provisional Tensioning Device Attach the provisional tensioning device and the attachment bit to the cable tensioner Turn the fluted knob at the end of the tensioner counterclockwise until it stops, and thread the cable through the cable tensioner. Advance the tensioner along the cable until it rests against the cable crimp. Carefully take up any slack in the cable by hand. Confirm placement of the crimp on the bone. Turn the knob on the tensioner clockwise until the desired tension is reached. The amount of tension being applied to the cable is indicated by the position of the knob relative to the numbered lines etched on the body of the tensioner. These lines indicate tension levels from 20 kg to 50 kg. Take care not to exceed 50 kg of tension. High tension may cause the cable to cut through soft or osteopenic bone. When the desired tension is reached, the cable is ready for crimping. Note: Applying more than 40 kg of tension to the 1.0 mm cable may cause fraying or breakage of the cable. It may also cause crushing of bone fragments and loss of reduction. Synthes 7
9 Cerclage Technique continued Optional technique The provisional tensioning device may be detached from the tensioner to hold tension in the cable while additional cables are placed. Engage the cam lock by pulling back on the provisional tensioning device lever. Turn the fluted knob of the tensioner counterclockwise until it stops and remove it from the provisional tensioning device. Each cable can then be incrementally tensioned before final crimping. Pull back to lock Note: Repeated tensioning of the cable at high loads may cause fraying of the cable. 8 Synthes Orthopaedic Cable System Technique Guide
10 4 Crimp cable Instrument Cable Crimper Use the cable crimper to precisely deform the cable crimp. Place the jaws of the cable crimper over the cable crimp and squeeze the handles together. The ratchet mechanism in the crimper precisely controls the amount of crimp deformation, thus preventing under- or overcrimping. The crimper will automatically release when the cable has been crimped. Note: Visually check to ensure that the cable crimp is centered and fully seated in the crimper jaws prior to crimping the cable. Improper placement may lead to cable slippage or crimp failure. Technique tip: Use the starter handle to begin squeezing the crimper until the outer handle can be easily grasped. Push forward to open After the cable has been crimped, remove the tensioner from the cable by turning the knob counterclockwise until the cable slides freely through the tensioner. If a provisional tensioning device was used, remove it at this time by pushing the provisional tensioning device lever forward. Crimp additional cables using the same procedure. Synthes 9
11 Cerclage Technique continued 5 Cut cable Instrument Cable Cutter, standard or Cable Cutter, large To cut the cable, pass the free end of the cable through the jaws of the cable cutter and squeeze the handles together. Cut each cable as close to the cable crimp as possible, taking care not to damage the adjacent cable. Technique tip: Place the cable completely in the cutter jaws, but near the tip. Cut in one motion to ensure a clean cut. 10 Synthes Orthopaedic Cable System Technique Guide
12 Cerclage Technique Using Cerclage Positioning Pins (optional) Note: When using cables in conjunction with plates and screws (and cerclage positioning pins or cerclage buttons), it is important to first reduce the plate to the bone. This is necessary because the fully tensioned cable will interfere with screw fixation if a gap exists between the plate and the bone. Instruments * 3.2 mm Drill Bit * 2.5 mm Drill Bit * 3.5 mm Universal Drill Guide * 4.5 mm Universal Drill Guide Figure Forceps, for use with cerclage buttons and positioning pins The cerclage positioning pin may be used when the fracture is treated with a plate. The positioning pin maintains the location of the cable on the plate relative to the plate hole. After reducing the plate to the bone, select the type of cerclage positioning pin to be used (post or threaded) and decide upon the location for the pin in the plate. For nonthreaded pins For 4.5 mm nonthreaded pins, drill a pilot hole into the bone, at the selected location for the pin, using a 3.2 mm drill bit and a 4.5 mm universal drill guide (Figure 1). For 3.5 mm nonthreaded pins, drill a pilot hole using a 2.5 mm drill bit and a 3.5 mm universal drill guide. * Also available Synthes 11
13 Cerclage Technique Using Cerclage Positioning Pins (optional) continued Note: Since the positioning pin is asymmetrically designed to fit into the majority of Synthes plates, ensure that the pin is appropriately oriented with respect to the pilot hole in the bone and the hole in the plate before loading the pin on the cable. For example: Consider the following situation when fixing a femur from a lateral approach using this technique. A pilot hole is drilled in the proximal half of a plate hole. The cable passer is inserted from posterior to anterior, which requires passing the cable from anterior to posterior. In this example, the non-threaded pin should be loaded onto the cable and fed down to the crimp with the post to the right when viewing the cable from the beaded end. Figure 2 Load the pin onto the cable and slide it down to the crimp before passing the cable around the bone (Figure 2). Pass the cable around the bone as described in Steps 1 2 (pages 5 and 6). Placing the post of the positioning pin in the pilot hole may be done by hand, or using the forceps for use with cerclage buttons and positioning pins. Seat the pin in the plate hole. Complete the remaining cerclage cable technique outlined in Steps 3 5 (pages 7 through 10). For threaded pins For the threaded pins, place the pin into locking holes before passing the cable around the bone (this can be done either before or after implantation of the plate). Ensure that the threads properly engage the plate, and the cable slot is perpendicular to the direction the cable will be passed around the bone (threaded pins do not have to be fully tightened into the plate). Insert the free end of the cable through the pin. Pass the cable around the bone, as described in Step 1 (page 5) and then into the crimp. Continue with the remaining cerclage cable technique outlined in Steps 3 5 (pages 7 through 10). Threaded cerclage positioning pin Cerclage positioning pin with post 12 Synthes Orthopaedic Cable System Technique Guide
14 Cerclage Technique Using Cerclage Buttons (optional) Instrument Forceps, for use with cerclage buttons and positioning pins A cerclage button may be used to provide additional fixation when a screw alone does not provide adequate fixation. Place a cerclage button in the head of a screw to provide fixation with a cable. Three sizes are available to fit small screwheads (T15 StarDrive or 2.5 mm hex recess), large screwheads (T25 StarDrive or 3.5 mm hex recess) or cannulated screws with 4 mm hex recess (5.0 mm cannulated locking, 6.5 mm cannulated, 7.3 mm cannulated, and 7.3 mm cannulated locking screws). Cerclage button Load the proper size cerclage button onto the cable and slide it down to the crimp before passing the cable around the bone. Pass the cable around the bone, as described in Step 1 (page 5). Place the button in the head of the screw using the forceps for use with cerclage buttons and positioning pins. Complete the remaining cerclage cable technique outlined in Steps 2 5 (pages 6 through 10). Synthes 13
15 Cerclage Technique Using Crimp Positioning Pins (optional) After reducing the plate to the bone, decide upon the location for the crimp positioning pin in the plate. The pin should be located in a locking hole, or the locking portion of a Combi hole. Remove the original crimp from the cable. Load the crimp positioning pin onto the cable and slide it down to the ball end of the cable. Pass the cable around the bone, as described in Step 1 (page 5). Insert the free end of the cable into the open hole of the crimp positioning pin and place the crimp positioning pin in the desired screw hole on the plate, while removing the cable slack. Complete the remaining cerclage cable technique outlined in Steps 3 5 (pages 7 through 10). 14 Synthes Orthopaedic Cable System Technique Guide
16 Cerclage Technique Using the 1.0 mm Titanium Needle Cable (optional) 1 Pass the cable Instrument Cable Cutter, standard Holding the end of the cable and the crimp in one hand, pass the needle tip of the cable around the bone and through the soft tissues. Needle leader Cut the needle leader, but do not cut the cable in order to prevent fraying. Pass the cable through the open hole in the crimp. Confirm placement of the crimp on the bone the smooth surface should be facing up. 2 Tension the cable Instrument Cable Tensioner Attachment Bit Provisional Tensioning Device Attach the provisional tensioning device and the attachment bit together. Thread the assembly onto one end of the cable so that the attachment bit butts up against the crimp. Engage the cam lock by pulling back the provisional tensioning device lever to lock the assembly in place. This will hold the cable against the crimp while applying tension to the other side. Synthes 15
17 Cerclage Technique Using the 1.0 mm Titanium Needle Cable (optional) continued 2 Tension the cable continued Attach the cable tensioner to the provisional tensioning device and the attachment bit. Turn the fluted knob at the end of tensioner fully clockwise until it stops, and thread the cable through the cable tensioner. Advance the tensioner along the cable until it rests against the cable crimp. Carefully take up any slack in the cable by hand. Confirm placement of the crimp on the bone Turn the knob on the tensioner clockwise until the desired tension is reached. The amount of tension being applied to the cable is indicated by the position of the knob relative to the numbered lines etched on the body of the tensioner. These lines indicate tension levels from 20 kg to 40 kg. When the desired tension is reached, the cable is ready for crimping. Note: Applying more than 40 kg of tension to the 1.0 mm cable may cause fraying or breakage of the cable. It may also cause crushing of bone fragments and loss of reduction Optional technique The provisional tensioning device may be detached from the tensioner to hold tension in the cable while additional cables are placed. Engage the cam lock by pulling back on the provisional tensioning device. Each cable can then be incrementally tensioned before final crimping. Note: Repeated tensioning of the cable at high loads may cause fraying or breakage of the cable. Complete the remaining cerclage cable technique outlined in Steps 4 5 (pages 9 and 10). 16 Synthes Orthopaedic Cable System Technique Guide
18 Tension Band Technique Olecranon Tension band technique is mainly indicated in avulsion fractures at the site of a ligament or tendon attachment, such as with fractures of the olecranon (osteotomy or transverse fractures) and patella (simple transverse fracture). Fractures (or osteotomies) of the greater trochanter and avulsion fractures of the medial or lateral malleolus may also be treated with a tension band. If strong rotational forces act upon the fracture site, two parallel Kirschner wires may be inserted before the tension band is applied. (For patella tension band technique, see page 23.) 1 Reduce fracture With the patient in the supine position and the arm draped free across the chest, reduce and temporarily fix the fracture, using pointed reduction forceps. Synthes 17
19 Tension Band Technique Olecranon continued 2 Insert Kirschner wires Instruments * 2.0 mm Drill Bit, quick coupling, 100 mm * 2.0 mm Parallel Drill Guide and Drill Sleeve Using a drill sleeve for aiming and tissue protection, insert two parallel (1.6 mm or 2.0 mm) Kirschner wires into the olecranon (in the direction of the long axis of the ulna) and across the fracture site. The Kirschner wires may be drilled into the anterior cortex of the ulna or placed within the medullary canal. In hard bone, predrilling with the 2.0 mm drill bit may be necessary. Drill a 2.0 mm hole perpendicular to the long axis of the ulna and distal to the fracture site, at a distance approximately equal to the length of the proximal fracture fragment. This hole must go through both cortices and the medullary canal of the ulna and may be drilled before or after fracture reduction and Kirschner wire placement. * Also available 18 Synthes Orthopaedic Cable System Technique Guide
20 3 Create tension band Place the crimp alongside the ulna and pass the 1.0 mm cable through the distal drill hole. Cross the cable over the dorsal surface of the olecranon and pass it deep to the triceps tendon and behind the Kirschner wires. Pass the cable end UNDER the cable on the dorsal surface of the ulna in a figure-of-eight and insert it into the open hole of the crimp. Gently pull any slack out of the cable by hand. Optional technique Use one or two screws (standard or cannulated) with cerclage buttons instead of the Kirschner wires. Under Over Tensioning direction Medial view Optional configuration Synthes 19
21 Tension Band Technique Olecranon continued 4 Tension cable Instruments Cable Tensioner Attachment Bit Provisional Tensioning Device Attach the provisional tensioning device and the attachment bit to the cable tensioner Turn the fluted knob at the end of the tensioner counterclockwise until it stops, and thread the cable through the cable tensioner. Advance the tensioner along the cable until it rests against the cable crimp. Carefully take up any slack in the cable by hand. Confirm placement of the crimp on the bone. Smooth surface facing up Place the elbow in extension. Turn the knob on the tensioner clockwise until the desired tension is reached. The amount of tension being applied to the cable is indicated by the position of the knob relative to the numbered lines etched on the body of the tensioner. These lines indicate tension levels from 20 kg to 50 kg. Take care not to exceed 40 kg of tension. Note: Applying tension at levels higher than 40 kg may result in crushing of the fragments and loss of reduction. When the desired tension is reached, the cable is ready for crimping. 20 Synthes Orthopaedic Cable System Technique Guide
22 5 Crimp cable Instrument Cable Crimper Place the jaws of the cable crimper over the cable crimp and squeeze the handles together. The ratchet mechanism in the crimper precisely controls the amount of crimp deformation, thus preventing underor over-crimping. The crimper will automatically release when the cable has been crimped. Note: Visually check to ensure that the cable crimp is centered and fully seated in the crimper jaws before crimping the cable. Improper placement may lead to cable slippage or crimp failure. Technique tip: Use the starter handle to begin squeezing the crimper until the outer handle can be easily grasped. After the cable has been crimped, remove the tensioner from the cable by turning the knob counterclockwise until the cable slides freely through the tensioner. Synthes 21
23 Tension Band Technique Olecranon continued 6 Cut cable Instrument Cable Cutter, standard To cut the cable, pass the free end of the cable through the jaws of the cable cutter and squeeze the handles together. Cut the cable as close to the cable crimp as possible, taking care not to damage the adjacent cable. Technique tip: Place the cable completely in the cutter jaws, but near the tip. Cut in one motion to ensure a clean cut. 7 Cut and position Kirschner wires Instruments * Wire-Bending Pliers, 160 mm * Bending Iron, for Kirschner Wires Pull the Kirschner wires back slightly and cut obliquely to create a sharp point. Using the wire bending pliers, bend the Kirschner wires past 180 to form a small hook. Using the bending iron for Kirschner wires as a punch, tap the ends into the bone making sure the cable passes under the small hook. Important: Do not use the cable cutters to cut the K-wires; doing so will damage the cutters. * Also available 22 Synthes Orthopaedic Cable System Technique Guide
24 Tension Band Technique Patella 1 Reduce the fracture Instrument * 2.0 mm Drill Bit, quick coupling, 100 mm Tilt the superior fracture fragment to expose the fracture surface. Using a 2.0 mm drill bit, drill two parallel holes in a retrograde fashion through the superior fragment. Insert a 1.6 mm Kirschner wire through each hole, blunt end first, and out through the quadriceps tendon. Advance the wires until the sharp tip is fully within the superior fragment. Reduce and provisionally fix the fracture with pointed reduction forceps. Inspect both the anterior cortical and posterior articular surfaces to ensure that the articular surface is anatomically reduced. * Also available Synthes 23
25 Tension Band Technique Patella continued 2 Insert Kirschner wires Instrument * Wire-Bending Pliers, 160 mm Sequentially advance the Kirschner wires into the inferior fragment. They should be advanced at least 1 cm beyond the inferior pole of the patella. Check reduction and provisional fixation. Using the wire bending pliers, bend the superior end of the Kirschner wires posteriorly past 180 to form a small hook, and cut obliquely to form sharp points. Important: Do not use the cable cutters to cut the Kirschner wires; doing so will damage the cutters. * Also available 24 Synthes Orthopaedic Cable System Technique Guide
26 3 Create tension band Place the crimp on the lateral or medial side of either pole of the patella. Pass a 1.0 mm cable deep to the quadriceps and patellar tendons and behind the Kirschner wires (superiorly and inferiorly), over the front of the patella in a figure-of-eight and back through the open hole in the crimp. Over Under Optional configuration Lateral view Synthes 25
27 Tension Band Technique Patella continued 4 Tension cable Instruments Cable Tensioner Attachment Bit Provisional Tensioning Device Attach the provisional tensioning device and the attachment bit to the cable tensioner Turn the fluted knob at the end of the tensioner counterclockwise until it stops and thread the cable through the cable tensioner. Advance the tensioner along the cable until it rests against the cable crimp. Carefully take up any slack in the cable by hand. Confirm placement of the crimp on the bone. Turn the knob on the tensioner clockwise until the desired tension is reached. The amount of tension being applied to the cable is indicated by the position of the knob relative to the numbered lines etched on the body of the tensioner. Smooth surface facing up These lines indicate tension levels from 20 kg to 50 kg. Take care not to exceed 40 kg of tension. Note: Applying tension at levels higher than 40 kg may result in crushing of the fragments and loss of reduction. When the desired tension is reached, the cable is ready for crimping. 26 Synthes Orthopaedic Cable System Technique Guide
28 5 Crimp cable Instrument Cable Crimper Place the jaws of the cable crimper over the cable crimp and squeeze the handles together. The ratchet mechanism in the crimper precisely controls the amount of crimp deformation, thus preventing under- or over-crimping. The crimper will automatically release when the cable has been crimped. Note: Visually check to ensure that the cable crimp is centered and fully seated in the crimper jaws before crimping the cable. Improper placement may lead to cable slippage or crimp failure. Technique tip: Use the starter handle to begin squeezing the crimper until the outer handle can be easily grasped. After the cable has been crimped, remove the tensioner from the cable by turning the knob counterclockwise until the cable slides freely through the tensioner. Synthes 27
29 Tension Band Technique Patella continued 6 Cut cable Instrument Cable Cutter, standard To cut the cable, pass the free end of the cable through the jaws of the cable cutter and squeeze the handles together. Cut the cable as close to the cable crimp as possible, taking care not to damage the adjacent cable. Technique tip: Place the cable completely in the cutter jaws, but near the tip. Cut in one motion to ensure a clean cut. 7 Cut and position K-wires Instrument * Bending Iron, for Kirschner Wires Using the bending iron for Kirschner wires as a punch, tap the ends of the bent Kirschner wires into the bone, making sure the cable passes through the small hook. Trim the protruding distal ends of the Kirschner wires at about 10 mm from the bone, and bend posteriorly only slightly, so that later extraction is not hampered. Important: Do not use the cable cutters to cut Kirschner wires; doing so will damage the cutters. * Also available 28 Synthes Orthopaedic Cable System Technique Guide
30 Implants Cerclage Positioning Pins, sterile 3.5 mm and 4.5 mm, threaded and nonthreaded Available in stainless steel and titanium Cerclage Buttons, sterile T15 StarDrive/2.5 mm hex T25 StarDrive/3.5 mm hex Cannulated 4.0 mm hex Available in stainless steel and titanium Crimp Positioning Pins, sterile 5.0 mm (stainless steel and titanium) 7.3 mm (stainless steel) Cables with Crimp, 750 mm, sterile 1.0 mm diameter (stainless steel and titanium) 1.0 mm diameter needle cable (titanium) 1.7 mm diameter (stainless steel) 1.7 mm diameter (CoCr cable with titanium crimp) Trochanteric Reattachment Devices with CoCr cable, sterile Standard Long Synthes 29
31 Instruments Medium Cable Passer, curved Large Cable Passer, curved Medium Cable Passer Medium Cable Passer, 45 angle Large Cable Passer Large Cable Passer, 45 angle 30 Synthes Orthopaedic Cable System Technique Guide
32 Cable Tensioner Cable Crimper Attachment Bit Provisional Tensioning Device Forceps, for use with Cerclage Buttons and Positioning Pins Cable Cutter, standard Cable Cutter, large Synthes 31
33 Orthopaedic Cable System Instrument Set ( ) Graphic Case Orthopaedic Cable System Instrument Set Graphic Case Instruments Medium Cable Passer, curved Large Cable Passer, curved Medium Cable Passer Medium Cable Passer, 45 angle Large Cable Passer Large Cable Passer, 45 angle Cable Tensioner Cable Crimper Attachment Bit, 4 ea Provisional Tensioning Device, 4 ea Forceps, for use with Cerclage Buttons and Positioning Pins Cable Cutter, standard Cable Cutter, large Note: For additional information, please refer to package insert. For detailed cleaning and sterilization instructions, please refer to or to the below listed inserts, which will be included in the shipping container: Processing Synthes Reusable Medical Devices Instruments, Instrument Trays and Graphic Cases DJ1305 Processing Non-sterile Synthes Implants DJ Synthes Orthopaedic Cable System Technique Guide
34 Also Available Kit Care and Maintenance Kit for Cable Tensioner, includes: 2.1 mm Cleaning Brush (319.27) 2.0 mm Cleaning Stylet (319.36) Autoclavable Oil (519.97) Instruments Cable Cutter with Trigger Handle Blade for Cable Cutter with Trigger Handle mm Kirschner Wire, with trocar point, 150 mm, 10/pkg mm Kirschner Wire, with trocar point, 150 mm, 10/pkg mm Drill Bit, quick coupling, 100 mm mm Drill Bit, quick coupling, 110 mm mm Drill Bit, quick coupling, 145 mm mm Parallel Drill Guide and Drill Sleeve mm Universal Drill Guide mm Universal Drill Guide Wire-Bending Pliers, 160 mm Impactor Bending Iron, for 1.25 mm, 1.6 mm and 2.0 mm Kirschner Wires Implants Cerclage Positioning Pins, sterile Stainless Steel Titanium S S 4.5 mm threaded S S 3.5 mm (nonthreaded) S S 3.5 mm threaded S S 4.5 mm (nonthreaded) Cerclage Buttons, sterile Stainless Steel Titanium S S T15 StarDrive/2.5 mm hex S S T25 StarDrive/3.5 mm hex S S Cannulated 4.0 mm hex Crimp Positioning Pins, sterile Stainless Steel Titanium S S 5.0 mm S n/a 7.3 mm Cables with Crimp, 750 mm, sterile Stainless Steel Titanium Dia S S 1.0 mm n/a S 1.0 mm (with needle) S n/a 1.7 mm S n/a 1.7 mm (10 pack) 1.7 mm CoCr Cable with Titanium Crimp, 750 mm, sterile S Single pack Titanium Trochanteric Reattachment Devices with CoCr cable, sterile S Standard S Long Synthes
35 Synthes (USA) 1302 Wrights Lane East West Chester, PA Telephone: (610) To order: (800) Fax: (610) Synthes (Canada) Ltd Meadowpine Boulevard Mississauga, Ontario L5N 6P9 Telephone: (905) To order: (800) Fax: (905) Synthes, Inc. or its affiliates. All rights reserved. Combi, DCP, LC-DCP, LCP and Synthes are trademarks of Synthes, Inc. or its affiliates. Printed in U.S.A. 8/10 J2848-G
Cable System. For Orthopaedic Trauma Surgery.
Cable System. For Orthopaedic Trauma Surgery. Surgical Technique This publication is not intended for distribution in the USA. Instruments and implants approved by the AO Foundation. Image intensifier
PERIPROSTHETIC IMPLANTS
PERIPROSTHETIC IMPLANTS PRODUCT OVERVIEW CLINICAL SOLUTIONS Periprosthetic fractures present unique challenges, such as how to gain fixation when the medullary canal is occupied. Special techniques and
The information contained in this document is intended for healthcare professionals only.
The information contained in this document is intended for healthcare professionals only. Dall-Miles Cabling System Dall-Miles Recon and Trauma Cable System Trochanteric Reattachment Using the Trochanteric
Technique Guide. Screw Removal Set. Instruments for removing Synthes screws.
Technique Guide Screw Removal Set. Instruments for removing Synthes screws. Table of Contents Introduction Screw Removal Set 2 Surgical Technique Preoperative Planning and Preparation 6 Removal of Intact
INTRODUCTION Cerclage Cable Vs. Monofilament Wire
B M P CABLE S Y S T E M S U R G I C A L TECHNIQUE INTRODUCTION The Biomet Medical Products (BMP ) Cable System provides a cost effective and simple method of trochanteric reattachment, fracture fixation,
Technique Guide. 3.5 mm and 4.5 mm Curved Locking Compression Plates (LCP). For minimally invasive osteosynthesis.
Technique Guide 3.5 mm and 4.5 mm Curved Locking Compression Plates (LCP). For minimally invasive osteosynthesis. Table of Contents Introduction 3.5 mm and 4.5 mm Curved Locking Compression 2 Plates (LCP)
Technique Guide. Large Fragment LCP Instrument and Implant Set. Part of the Synthes locking compression plate (LCP) system.
Technique Guide Large Fragment LCP Instrument and Implant Set. Part of the Synthes locking compression plate (LCP) system. Table of Contents Introduction Large Fragment LCP Instrument and Implant Set
Modular Sternal Cable System. Flexibility and strength in sternal closure and repair.
Modular Sternal Cable System. Flexibility and strength in sternal closure and repair. Multiple closure options Stable fixation in all configurations Improved strength and flexibility compared to wire Modular
Zimmer Periarticular Proximal Tibial Locking Plate
Zimmer Periarticular Proximal Tibial Locking Plate Surgical Technique The Science of the Landscape Zimmer Periarticular Proximal Tibial Locking Plate 1 Table of Contents Introduction 2 Locking Screw Technology
Technique Guide. 4.5 mm LCP Proximal Femur Plates. Part of the Synthes Periarticular LCP Plating System.
Technique Guide 4.5 mm LCP Proximal Femur Plates. Part of the Synthes Periarticular LCP Plating System. Table of Contents Introduction 4.5 mm LCP Proximal Femur Plates 2 AO Principles 4 Indications 5 Surgical
NCB Distal Femur System. Surgical Technique
NCB Distal Femur System Surgical Technique NCB Distal Femur System Surgical Technique 3 Surgical Technique NCB Distal Femur System Table of Contents Introduction 4 Indications 8 Preoperative Planning
How To Use A Phoenix Retrograde Femoral Nail
Phoenix Retrograde Femoral Nail System Featuring CoreLock Technology Surgical Technique Contents Introduction... Page 1 Indications... Page 2 Design Features... Page 3 Surgical Technique... Page 6 Product
Technique Guide. DHS/DCS Dynamic Hip and Condylar Screw System. Designed to provide stable internal fixation.
Technique Guide DHS/DCS Dynamic Hip and Condylar Screw System. Designed to provide stable internal fixation. Table of Contents Introduction Dynamic Hip Screw (DHS) 2 Dynamic Condylar Screw (DCS) 3 Indications
MINI FRAGMENT SYSTEM. Instruments and implants for 1.5 mm, 2.0 mm, and 2.4 mm plate fixation PRODUCT OVERVIEW
MINI FRAGMENT SYSTEM Instruments and implants for 1.5 mm, 2.0 mm, and 2.4 mm plate fixation PRODUCT OVERVIEW TABLE OF CONTENTS INTRODUCTION Mini Fragment System 2 PRODUCT INFORMATION Plates 4 Screws 6
Zimmer Periarticular Elbow Locking Plate System
Zimmer Periarticular Elbow Locking Plate System Surgical Technique The Right Solutions for Fractures Around the Elbow Disclaimer This document is intended exclusively for physicians and is not intended
Titanium Wire with Barb and Needle. For canthal tendon procedures.
Titanium Wire with Barb and Needle. For canthal tendon procedures. Technique Guide Instruments and implants approved by the AO Foundation Table of Contents Introduction Titanium Wire with Barb and Needle
Zimmer Small Fragment Universal Locking System. Surgical Technique
Zimmer Small Fragment Universal Locking System Surgical Technique Zimmer Small Fragment Universal Locking System 1 Zimmer Small Fragment Universal Locking System Surgical Technique Table of Contents Introduction
NCB Periprosthetic Femur Plate System. Surgical Technique
NCB Periprosthetic Femur Plate System Surgical Technique NCB Periprosthetic Femur System Surgical Technique 3 Table of Contents Introduction 4 System Features and Benefits 9 Indications and Contraindications
Technique Guide. 2.4 mm LCP Distal Radius System. A comprehensive plating system to address a variety of fracture patterns.
Technique Guide 2.4 mm LCP Distal Radius System. A comprehensive plating system to address a variety of fracture patterns. Table of Contents Introduction 2.4 mm LCP Distal Radius System 2 AO Principles
ACCORD Cable System. Surgical technique completed in conjunction with: Robert Barrack, MD St. Louis, Missouri. Paul Di Cesare, MD New York, New York
Surgical Technique Innovations in Hip Surgery 2 ACCORD Cable System Surgical technique completed in conjunction with: Robert Barrack, MD St. Louis, Missouri Paul Di Cesare, MD New York, New York Fares
LCP Superior Clavicle Plate. The anatomically precontoured fixation system with angular stability for clavicle shaft and lateral clavicle.
LCP Superior Clavicle Plate. The anatomically precontoured fixation system with angular stability for clavicle shaft and lateral clavicle. Surgical Technique This publication is not intended for distribution
Orthopedic Foot Instruments. Dedicated instruments for reconstructive foot surgery.
Orthopedic Foot Instruments. Dedicated instruments for reconstructive foot surgery. Surgical Technique This publication is not intended for distribution in the USA. Instruments and implants approved by
Battery Power Line. Battery-driven power tool system for orthopaedics and traumatology.
Battery Power Line. Battery-driven power tool system for orthopaedics and traumatology. High performance Excellent torque for drilling and reaming Precise cutting with Synthes saw blades Battery Power
Technique Guide. Reamer/Irrigator/Aspirator (RIA). For intramedullary reaming and bone harvesting.
Technique Guide Reamer/Irrigator/Aspirator (RIA). For intramedullary reaming and bone harvesting. Table of Contents Introduction Reamer/ Irrigator/ Aspirator (RIA) 2 Indications 4 Surgical Technique Preparation
Arthroscopic Shoulder Instability Repair Using the SUTUREFIX ULTRA Suture Anchor and SUTUREFIX ULTRA Instrumentation System
*smith&nephew SHOULDER TECHNIQUE GUIDE Arthroscopic Shoulder Instability Repair Using the SUTUREFIX ULTRA Suture Anchor and SUTUREFIX ULTRA Instrumentation System KNEE HIP SHOULDER EXTREMITIES Arthroscopic
How To Fix A Radial Head Plate
Mayo Clinic CoNGRUENT RADIAL HEAD PLATE Since 1988 Acumed has been designing solutions to the demanding situations facing orthopedic surgeons, hospitals and their patients. Our strategy has been to know
Technique Guide. 2.7 mm/3.5 mm Variable Angle LCP Ankle Trauma System. Part of the Synthes variable angle locking compression plate (VA-LCP) system.
Technique Guide 2.7 mm/3.5 mm Variable Angle LCP Ankle Trauma System. Part of the Synthes variable angle locking compression plate (VA-LCP) system. Table of Contents Introduction 2.7 mm/3.5 mm Variable
Lentur Cable System. Surgical Technique
Lentur Cable System Surgical Technique Contents Introduction... Page 1 System Design Features And Benefits... Page 2 Implants... Page 3 Instrumentation... Page 4 Surgical Technique... Page 5 Single Cable...
Zimmer Natural Nail System. Cephalomedullary Nail Surgical Technique STANDARD
Zimmer Natural Nail System Cephalomedullary Nail Surgical Technique STANDARD Zimmer Natural Nail System Cephalomedullary Nail Surgical Technique - Standard 1 Zimmer Natural Nail System Cephalomedullary
Posterior Referencing. Surgical Technique
Posterior Referencing Surgical Technique Posterior Referencing Surgical Technique INTRO Introduction Instrumentation Successful total knee arthroplasty depends in part on re-establishment of normal lower
Technique Guide. Titanium Trochanteric Fixation Nail System. For intramedullary fixation of proximal femur fractures.
Technique Guide Titanium Trochanteric Fixation Nail System. For intramedullary fixation of proximal femur fractures. Table of Contents Introduction Titanium Trochanteric Fixation Nail System 2 Biomechanical
V-TEK IVP System 2.7 System 4.0
V-TEK IVP System Ankle 2.7 Fix System 4.0 Surgical Technique Surgical Technique Titanium osteosynthesis system for tibio-talar and tibio-talo-calcaneal fusion SECTION 1 Ankle Fix System 4.0 Titanium osteosynthesis
Shoulder Restoration System
Shoulder Restoration System PopLok Knotless Suture Anchor Simple, Secure, Versatile all-peek knotless anchor system for rotator cuff and instability repairs CO M M I T T ED TO I N N OVATI O N SURGICAL
LCP Compact Foot/Compact Hand.
LCP Compact Foot/Compact Hand. Surgical Technique This publication is not intended for distribution in the USA. Instruments and implants approved by the AO Foundation. Table of contents Indications 2
Expert LFN. Lateral Femoral Nail.
Expert LFN. Lateral Femoral Nail. Surgical Technique EXPERT Nailing System This publication is not intended for distribution in the USA. Instruments and implants approved by the AO Foundation. Image intensifier
SALVATION. Fusion Bolts and Beams SURGICAL TECHNIQUE
SALVATION Fusion Bolts and Beams SURGICAL TECHNIQUE Contents Chapter 1 4 Introduction Chapter 2 4 Intended Use Chapter 3 4 Device Description 4 Fusion Beams 5 Fusion Bolts Chapter 4 5 Preoperative Planning
Small Battery Drive. For orthopaedic trauma applications.
Small Battery Drive. For orthopaedic trauma applications. Ergonomic, lightweight design Compatible with a wide variety of attachments Variable speed trigger with instant reverse and oscillation Small
DHS/DCS System. Including LCP DHS and DHS Blade.
DHS/DCS System. Including LCP DHS and DHS Blade. Surgical Technique This publication is not intended for distribution in the USA. Instruments and implants approved by the AO Foundation. Table of Contents
NCB Proximal Humerus System. Surgical Technique
NCB Proximal Humerus System Surgical Technique NCB Proximal Humerus System Surgical Technique 3 Surgical Technique NCB Proximal Humerus System Table of Contents Introduction 4 Cable Fixation Options 5
TwinFix Cannulated Compression Screw
TwinFix Cannulated Compression Screw Leibinger Solutions for Hand Surgery Procedural Guide TwinFix Sterilization, Organization, Storage 29-12020 Profyle MODULAR Sterilizing Container 29-40162 TwinFix Implant
LCP Olecranon Plate. The anatomical fixation system with angular stability for olecranon and proximal ulnar fractures.
LCP Olecranon Plate. The anatomical fixation system with angular stability for olecranon and proximal ulnar fractures. Surgical Technique This publication is not intended for distribution in the USA. Instruments
the revo / mini-revo shoulder fixation system s u r g i c a l t e c h n i q u e
the revo / mini-revo shoulder fixation system s u r g i c a l t e c h n i q u e REVO The following techniques are described by Stephen J. Snyder, M.D., Van Nuys, CA. Arthroscopic repair of the rotator
Achilles Tendon Repair, Operative Technique
*smith&nephew ANKLE TECHNIQUE GUIDE Achilles Tendon Repair, Operative Technique Prepared in Consultation with: C. Niek van Dijk, MD, PhD KNEE HIP SHOULDER EXTREMITIES Achilles Tendon Repair, Operative
TFN Titanium Trochanteric Fixation Nail System. For intramedullary fixation of proximal femur fractures.
TFN Titanium Trochanteric Fixation Nail System. For intramedullary fixation of proximal femur fractures. Surgical Technique This publication is not intended for distribution in the USA. Instruments and
Anterior Lumbar Interbody Fusion (ALIF). Instrument set supports placement of ALIF spacers using anterior or anterolateral approach.
Anterior Lumbar Interbody Fusion (ALIF). Instrument set supports placement of ALIF spacers using anterior or anterolateral approach. Technique Guide Instruments and implants approved by the AO Foundation
Expert ALFN. Adolescent Lateral Femoral Nail.
Expert ALFN. Adolescent Lateral Femoral Nail. Surgical Technique EXPERT Nailing System This publication is not intended for distribution in the USA. Instruments and implants approved by the AO Foundation.
Expert HAN. Expert Hindfoot Arthrodesis Nail.
Expert HAN. Expert Hindfoot Arthrodesis Nail. Surgical Technique Expert Nailing System This publication is not intended for distribution in the USA. Instruments and implants approved by the AO Foundation.
GENEL KATALOG GENERAL CATALOGUE KİLİTSİZ PLAKLAR NON LOCKING PLATES
KİLİTSİZ PLAKLAR NON LOCKING PLATES 33 34 35 36 37 38 39 40 41 42 43 44 45 46 Ulnar Olecranon Plate Ti DELİK KAT.NO. HOLE CAT.NO. 3 A22014030 4 A22014040 5 A22014050 6 A22014060 7 A22014070 8 A22014080
CLAW II. Polyaxial Compression Plating System SURGIC A L T ECHNIQUE
CLAW II Polyaxial Compression Plating System SURGIC A L T ECHNIQUE Contents Chapter 1 2 3 3 3 Chapter 2 4 4 7 Chapter 3 8 8 8 8 8 8 8 9 11 11 11 Chapter 4 12 Introduction Intended Use Indications Contraindications
Expert TN. Tibial Nail.
Expert TN. Tibial Nail. Surgical Technique Expert Nailing System This publication is not intended for distribution in the USA. Instruments and implants approved by the AO Foundation. Image intensifier
WIRE AND PIN MANAGEMENT
WIRE AND PIN MANAGEMENT SECTION S To store, autoclave, dispense, insert, hold, bend, pull, twist, cut, and tighten K-wires, guidewires, Steinmann pins and rods. CONTENTS Wire Storage and Sterilization
Scout Vessel Guard. A cover for vessels during anterior lumbar spine surgery.
Scout Vessel Guard. A cover for vessels during anterior lumbar spine surgery. Technique Guide Instruments and implants approved by the AO Foundation Table of Contents Introduction Scout Vessel Guard 2
DRAFT. Triathlon TS Knee System. Surgical Protocol. Version 1
DRAFT Version 1 Triathlon TS Knee System Table of Contents Acknowledgments..........................................................2 Tibial Canal Preparation....................................................4
Elbow System 2.0, 2.8
SurgicAL TecHNiqUE STEP by step Elbow System 2.0, 2.8 APTUS Elbow 2 Elbow System 2.0, 2.8 Elbow System 2.0, 2.8 3 Elbow System 2.0, 2.8 Contents 4-5 Features, Technique 6-13 Introduction and Indications
Aesculap Veterinary Orthopaedics. Targon VET Interlocking Nail
Aesculap Veterinary Orthopaedics Targon VET Interlocking Nail Flexibility Stability Dynamics The Targon VET is based on new, technology which reverses the known principles of interlocking nails. The rotation-stabilising
OptiLock Periarticular Plating System For Proximal Tibial Fractures. Pre-Launch Surgical Technique
OptiLock Periarticular Plating System For Proximal Tibial Fractures Pre-Launch Surgical Technique Contents Introduction... Page 1 Indications & Fracture Classifications... Page 4 Design Features... Page
Anteromedial ACL Reconstruction Surgical Technique for Soft Tissue Grafts
Anteromedial ACL Reconstruction Surgical Technique for Soft Tissue Grafts Advancing ACL Reconstruction with implant absorption and ossification of the Implant site 2,3,5 The MILAGRO BR Interference Screw
TRIGEN INTERTAN Intertrochanteric Antegrade Nail Surgical Technique. Table of Contents
Surgical Technique TRIGEN INTERTAN Intertrochanteric Antegrade Nail Surgical Technique As described by: Andreas H. Ruecker, MD Thomas A. Russell, MD Roy W. Sanders, MD Paul Tornetta, MD Table of Contents
Implant Extraction Guide Module One & Two
Implant Extraction Set Implant Extraction Guide Module One & Two 1 Contents Page 1. Introduction 3 Introduction 3 Features and Benefits 3 Contraindications 3 2. Product Description 4 3. Technical Details
Integra. Subtalar MBA and bioblock Implant SURGICAL TECHNIQUE
Integra Subtalar MBA and bioblock Implant SURGICAL TECHNIQUE Table of contents Introduction Description... 2 Indications... 2 Contraindications... 2 Surgical Technique Step 1: Incision and Dissection...3
Surgical technique. End Cap for TEN. For axial stabilization and simultaneous protection of soft tissue.
Surgical technique End Cap for TEN. For axial stabilization and simultaneous protection of soft tissue. Table of contents Indications and contraindications 3 Implants 4 Instruments 4 Preoperative planning
TransFx External Fixation System Large and Intermediate Surgical Technique
TransFx External Fixation System Large and Intermediate Surgical Technique TransFx External Fixation System Large and Intermediate Surgical Technique 1 Surgical Technique For TransFx External Fixation
Zimmer FuZion Instruments. Surgical Technique (Beta Version)
Zimmer FuZion Surgical Technique (Beta Version) INTRO Surgical Technique Introduction Surgical goals during total knee arthroplasty (TKA) include establishment of normal leg alignment, secure implant fixation,
Trillium 40 Axis Spring Tensioner Wire Replacement Instructions
Trillium 40 Axis Spring Tensioner Wire Replacement Instructions 1 Overview The objective is to replace the broken axis spring tensioner wire. This requires the following tasks: 1. Remove the seismometer
Restoration Modular. Revision Hip System Surgical Protocol
Orthopaedics Restoration Modular Revision Hip System Restoration Modular Calcar Body/Conical Distal Stem Femoral Components Using the Restoration Modular Instrument System Revision Hip System Orthopaedics
ZERO-P VA. Variable angle zero-profile anterior cervical interbody fusion (ACIF) device SURGICAL TECHNIQUE
ZERO-P VA Variable angle zero-profile anterior cervical interbody fusion (ACIF) device SURGICAL TECHNIQUE Table of Contents Introduction Zero-P VA Instruments and Implants 2 AO Principles 4 Indications
The information contained in this document is intended for healthcare professionals only.
The information contained in this document is intended for healthcare professionals only. Monogram Total Knee Instruments Modular Rotating Hinge Knee System Keel Baseplate Using Monogram IM Revision Instruments
DARCO MRS. Locked Plating System for Reconstructive Rearfoot Surgery
DARCO MRS Locked Plating System for Reconstructive Rearfoot Surgery DARCO MRS Locked plating system for reconstructive rearfoot surgery System Basics The DARCO MRS plating system for the rearfoot has been
Knotilus TM. Anchor Instability Repair. Technique Guide
Knotilus TM Anchor Instability Repair Technique Guide Instability Repair Using the Knotilus TM Anchor Introduction While the shoulder has more mobility than any other joint in the body, it is also the
Zimmer MOST Options System
Zimmer MOST Options System Surgical Technique Modular Options for Severe Bone Loss and Trauma Zimmer MOST Options System Surgical Technique 1 MOST Options System Surgical Technique Table of Contents Introduction
VERSYS HERITAGE CDH HIP PROSTHESIS. Surgical Technique for CDH Hip Arthroplasty
VERSYS HERITAGE CDH HIP PROSTHESIS Surgical Technique for CDH Hip Arthroplasty SURGICAL TECHNIQUE FOR VERSYS HERITAGE CDH HIP PROSTHESIS CONTENTS ANATOMICAL CONSIDERATIONS....... 2 PREOPERATIVE PLANNING............
Malleolar fractures Anna Ekman, Lena Brauer
Malleolar fractures Anna Ekman, Lena Brauer How to use this handout? The left column is the information as given during the lecture. The column at the right gives you space to make personal notes. Learning
Trabecular Metal Femoral Component. Surgical Technique
Trabecular Metal Femoral Component Surgical Technique INTRO Trabecular Metal Femoral Component Surgical Technique Introduction The Persona Trabecular Metal Femoral Component is designed to unite stable
VariAx Distal Radius Locking Plate System. Anatomical & Universal Volar Plates Dorsal Plates Fragment Specific Plates
VariAx Distal Radius Plate System Anatomical & Universal Volar Plates Dorsal Plates Fragment Specific Plates System Module The NEW VariAx Distal Radius Plating System represents the Next Generation of
Versa-Fx II Femoral Fixation System Surgical Techniques
Versa-Fx II Femoral Fixation System Surgical Techniques Versa-Fx II Femoral Fixation System Surgical Techniques 1 Surgical Technique For Fixation Of Intertrochanteric and Supracondylar Fractures of the
Foot and Ankle Technique Guide Proximal Inter-Phalangeal (PIP) Fusion
Surgical Technique Foot and Ankle Technique Guide Proximal Inter-Phalangeal (PIP) Fusion Prepared in consultation with: Phinit Phisitkul, MD Department of Orthopedics and Rehabilitation University of Iowa
Anatomic Percutaneous Ankle Reconstruction of Lateral Ligaments (A Percutaneous Anti ROLL)
Anatomic Percutaneous Ankle Reconstruction of Lateral Ligaments (A Percutaneous Anti ROLL) Mark Glazebrook James Stone Masato Takao Stephane Guillo Introduction Ankle stabilization is required when a patient
Bankart Repair using the Smith & Nephew BIORAPTOR 2.9 Suture Anchor
Shoulder Series Technique Guide *smith&nephew BIORAPTOR 2.9 Suture Anchor Bankart Repair using the Smith & Nephew BIORAPTOR 2.9 Suture Anchor Gary M. Gartsman, M.D. Introduction Arthroscopic studies of
TABLE OF CONTENTS. Indications and Contraindications 3. Features and Benefits 4. Ease of connection 4 Stable fixation concept 5
Surgical Technique TABLE OF CONTENTS Indications and Contraindications 3 Features and Benefits 4 Ease of connection 4 Stable fixation concept 5 Surgical Technique Steps 6 Identification and preparation
Technique Guide. Norian SRS Fast Set Putty. Calcium phosphate bone void filler.
Technique Guide Norian SRS Fast Set Putty. Calcium phosphate bone void filler. TableofContents Introduction Norian SRS Fast Set Putty 2 Indications and Contraindications 3 Basic Science 4 Surgical Technique
TABLE OF CONTENTS. Surgical Technique 2. Indications 4. Product Information 5. 1. Patient Positioning and Approach 2
Surgical Technique TABLE OF CONTENTS Surgical Technique 2 1. Patient Positioning and Approach 2 2. Intervertebral Device Implanted 2 3. Buttress Plate Selection 2 4. Awl Insertion 2 5. Screw Insertion
ORTHODONTIC MINI IMPLANTS Clinical procedure for positioning. Orthodontics and Implantology
ORTHODONTIC MINI IMPLANTS Clinical procedure for positioning Orthodontics and Implantology 2 All rights are reserved. Any reproduction of the present publication is prohibited in whole or in part and by
Mini TightRope CMC Surgical Technique
Mini TightRope CMC Surgical Technique Mini TightRope CMC Mini TightRope CMC Fixation The Mini TightRope provides a unique means to suspend the thumb metacarpal after partial or complete trapezial resection
Fracture Fixation Devices Compression Hip Screws Cannulated/Bone Screws Bone Plates, Pins, Wires
Fracture Fixation Devices Compression Hip Screws Cannulated/Bone Screws Bone Plates, Pins, Wires IMPORTANT MEDICAL INFORMATION EN SPECIAL NOTE Fracture fixation devices are used only as an aid to healing;
ACTIV ANKLE DISTAL AND DIAPHYSEAL FIBULA INNOVATION MEANS MOTION
ACTIV ANKLE DISTAL AND DIAPHYSEAL FIBULA POLYAXIAL LOCKING FIXATION DUALTEC SYSTEM II Precontoured implants Polyaxiality of 20 2 surgical approaches : lateral and posterolateral ACTIV ANKLE The ACTIV ANKLE
ACL Reconstruction with Bone-Tendon-Bone Transplants Using the ENDOBUTTON CL BTB Fixation System
Knee Series Technique Guide ACL Reconstruction with Bone-Tendon-Bone Transplants Using the ENDOBUTTON CL BTB Fixation System Stuart Fromm, M.D. As described by: Stuart Fromm, M.D. Black Hills Orthopedic
Stabilization of Acute Acromioclavicular Joint Dislocations using Dog Bone Button Technology Surgical Technique
Stabilization of Acute Acromioclavicular Joint Dislocations using Dog Bone Button Technology Surgical Technique AC Repair - Dog Bone Button Stabilization of Acute Acromioclavicular Joint Dislocations using
Ankle Syndesmosis Surgical Protocol by Timothy Charlton, M.D.
Featuring Ankle Syndesmosis Surgical Protocol by Timothy Charlton, M.D. ZipLoop Technology is a unique weave in which a single strand of braided polyethylene is woven through itself twice in opposite directions.
M/DN Femoral Interlocking & Recon Nail Intramedullary Fixation Surgical Technique
M/DN Femoral Interlocking & Recon Nail Intramedullary Fixation Surgical Technique M/DN Femoral Interlocking & Recon Nail Intramedullary Fixation 1 Surgical Techniques for Fixation of Femoral Fractures
TRIGEN TAN and FAN Intramedullary Nails
Surgical Technique TRIGEN TAN and FAN Intramedullary Nails Surgical Technique Table of Contents Indications...2 TRIGEN TAN and FAN Case Examples...3 Design Features: TAN...4 Implant Specifications: TAN...5
Zimmer NexGen CR-Flex and LPS-Flex Knees. Surgical Technique with Posterior Referencing Instrumentation
Zimmer NexGen CR-Flex and LPS-Flex Knees Surgical Technique with Posterior Referencing Instrumentation INTRO Zimmer NexGen CR-Flex and LPS-Flex Knees Surgical Technique with Posterior Referencing Instrumentation
LISS PLT. The less invasive stabilization system for proximal tibia fractures.
LISS PLT. The less invasive stabilization system for proximal tibia fractures. Surgical Technique This publication is not intended for distribution in the USA. Instruments and implants approved by the
BONE PRESERVATION STEM
TRI-LOCK BONE PRESERVATION STEM Featuring GRIPTION Technology SURGICAL TECHNIQUE IMPLANT GEOMETRY Extending the TRI-LOCK Stem heritage The original TRI-LOCK Stem was introduced in 1981. This implant was
METAL HEMI. Great Toe Implant SURGICAL TECHNIQUE
METAL HEMI Great Toe Implant SURGICAL TECHNIQUE Contents Chapter 1 4 Product Information 4 Device Description Chapter 2 5 Intended Use 5 Indications 5 Contraindications Chapter 3 6 Surgical Technique
758 Heavy-duty Ratchet Guy Wire Cutter
INSTRUCTION MANUAL 758 Heavy-duty Ratchet Guy Wire Cutter Read and understand all of the instructions and safety information in this manual before operating or servicing this tool. Register this product
Elo Touch Solutions Wall-mounting Kit for the 5501L IDS Touchmonitors
Installation Manual Elo Touch Solutions Wall-mounting Kit for the 5501L IDS Touchmonitors SW602206 Rev B Table of Contents Chapter 1: Safety Warning... 3 Chapter 2: Kit Contents... 4 Included in Kit...
Minimally Invasive Lumbar Fusion
Minimally Invasive Lumbar Fusion Biomechanical Evaluation (1) coflex-f screw Biomechanical Evaluation (1) coflex-f intact Primary Stability intact Primary Stability Extension Neutral Position Flexion Coflex
Zimmer PSI Knee System For Use with Persona The Personalized Knee System Surgical Technique
Zimmer PSI Knee System For Use with Persona The Personalized Knee System Surgical Technique TOC Zimmer PSI Knee Surgical Technique Zimmer PSI Knee Surgical Technique Table of Contents Intra-Operative Guide
TABLE OF CONTENTS. I. TROUBLESHOOTING... 2 - Section 1.01: Common Problems/Solutions... 2
BAL Accu-Slide System I. Table of Contents TABLE OF CONTENTS I. TROUBLESHOOTING... 2 - Section 1.01: Common Problems/Solutions... 2 II. GETTING STARTED... 5 - Section 2.01: Tools You Will Need... 5 - Section
AstroSystems Digital Setting Circles for Zhumell, GSO, Apertura and Astro-Tech
AstroSystems Digital Setting Circles for Zhumell, GSO, Apertura and Astro-Tech Components 1 Sky Commander Digital Setting Circle Computer 2 Encoders 10,000 step 1 Sky Commander Digital Setting Circle Manual