THX9321 Prestige 2.0 THX9421 Prestige IAQ 2.0 with EIM

Save this PDF as:
 WORD  PNG  TXT  JPG

Size: px
Start display at page:

Download "THX9321 Prestige 2.0 THX9421 Prestige IAQ 2.0 with EIM"

Transcription

1 TM System Installation Guide THX9 Prestige.0 THX94 Prestige IAQ.0 with EIM With wireless accessories ontrol for up to 4 Heat/ ool heat pump systems or up to Heat/ ool conventional systems for residential and commercial applications. Installation guide for: Prestige THX9/94 thermostat Equipment Interface Module (EIM) Portable omfort ontrol Wireless Outdoor Sensor Wireless Indoor Sensor edlink Internet Gateway Quick start guide Install thermostat...page Install optional Equipment Interface Module (EIM)... Power optional accessories Link thermostat to wireless network Link optional accessories to wireless network Install optional sensors Setup installer options...8 Wiring guides Key features Device replacement and specifications DISONNET POWE EFOE INSTALLATION. an cause electrical shock or equipment damage. MEUY NOTIE: If this product is replacing a control that contains mercury in a sealed tube, do not place the old control in the trash. ontact the Thermostat ecycling orporation at or for information on how and where to properly and safely dispose of your old thermostat. Must be installed by a trained, experienced technician. ead these instructions carefully. Failure to follow these instructions can damage the product or cause a hazardous condition. U.S. egistered Trademark. opyright 0 Honeywell International Inc. All rights reserved

2 System Installation Guide Your Honeywell advantage edlink ompatible Increase your content and profit per job by including edlink accessories that meet your customers' comfort and convenience needs. edlink accessories include the Wireless Outdoor Sensor, Portable omfort ontrol (P), Equipment Interface Module (EIM), edlink Internet Gateway, Wireless Indoor Sensor, TrueSTEAM humidifier with Wireless Adapter, TrueZONE zoning panel with Wireless Adapter, Vent oost emote and Entry/ Exit emote. ustomizable Service eminders Set up to 0 service reminders. hoose from the pre-set options or customize your own. eminders based on date, outdoor temperature or a dry contact input will alert customers with instructions to contact you for assistance. Delta T Alerts and Diagnostics Alerts give customers a sense of security while also enabling you to service or replace the equipment prior to a loss of heating or cooling. ased on limits you set at installation, customers can be alerted when their system is not operating as expected. The system alert will instruct customers to contact you for assistance. equires EIM. Delta T Installer Test Save time by viewing Delta T while running a system test to verify proper operation. equires EIM. Universal Inputs S and S Assignable inputs allow you to configure Indoor and Outdoor Temperature Sensors, Discharge and eturn Air Sensors or Dry ontact Devices. Dry ontact Devices can be used to trip pre-set or customized alerts on the thermostat home screen. equires EIM. User Interactions Log The interaction log stores history of thermostat setting changes including temperature, system and installer setup. You can use the interaction log to save time by determining if the issue is a system error or an accidental user error. onfigurable for esidential and Light ommercial Applications One thermostat does it all to meet the needs of esidential and Light ommercial applications. Simply select esidential or ommercial during the installer setup. If ommercial is selected, the thermostat will use commercial language, meet building codes and offer 65 day holiday scheduling. US Port for Quick Installer Setup Save time by using a US stick to upload installer settings and service reminders in one simple step. Selectable Sensors When paired with a Wireless Indoor Sensor(s) you have the ability to choose which sensor(s) to use for temperature, humidification and dehumidification. They can be used in combination for temperature averaging or individually to condition humidity levels in separate spaces

3 THX9/94 Prestige IAQ and F EIM Install thermostat M9 M86 THX94: Mount the thermostat and wire to and terminals of the Equipment Interface Module (EIM), or to a separate volt transformer (not provided). THX9: Install and wire as above if using EIM. If not, see pages -5. When the THX9 thermostat is used with the EIM, the relays in the thermostat do not function. M87 See pages 0-7 for detailed wiring guidelines Install Equipment Interface Module (if used) [If no EIM is used, skip to Section.] Use screws & anchors as appropriate for the mounting surface. Mount the EIM near the H equipment, or on the equipment itself. Strip /4 insulation, then insert wires as shown. W AUX W O/ W AUX Y Y G A L/A M89A M88 NOTE: If you install more than one thermostat and EIM, the EIMs must be at least feet apart. If you are installing discharge and return air sensors, refer to the mounting instructions in the Alerts and Delta T Diagnostics Installation Instructions packed with the Prestige IAQ.0 kit

4 System Installation Guide Power optional accessories [If no wireless accessories are used, skip to Section 4.] Wireless Outdoor Sensor Wireless Indoor Sensor Portable omfort ontrol M97 Install fresh AA lithium batteries M98 Install fresh AAA alkaline batteries M99 Install fresh AA alkaline batteries edlink Internet Gateway The Honeywell edlink Internet Gateway gives your customers remote access to home climate-control systems from any location with Internet access. Using a Web browser, users can review and adjust indoor temperature, system mode and other settings. The Gateway can also send alerts to as many as 6 addresses if a problem occurs. onnect edlink Gateway to a router or modem with Ethernet cable (J45). onnect power cord to an electrical outlet not controlled by a wall switch M

5 THX9/94 Prestige IAQ and F EIM 4 Link thermostat to the wireless network (if used with an EIM or TrueZONE Wireless Adapter) Next, link all components and edlink accessories to the wireless network. Initial powerup When the thermostat is first activated, it will lead you through the steps necessary to define and set up your system. The steps will change depending on the type of system and thermostat you're installing. Setup options for THX9 Setup options for THX94 If non-zoned system: Setup for thermostat only Setup for use with EIM If zoned system: Setup for EIM wired to zone panel Setup for thermostat wired to zone panel Setup for edlink wireless connection to zone panel (using THM4000 TrueZONE Wireless Adapter) If non-zoned system: Setup for EIM connection If zoned system: Setup for EIM wired to zone panel Setup for edlink wireless connection to zone panel (using THM4000 TrueZONE Wireless Adapter) Link thermostat to EIM or TrueZONE Wireless Adapter Use the step-by-step thermostat menus to define your system type (above). When you reach the Wireless Setup screen, follow the steps below: ONNETED ONNET S S S S Press and release the ONNET button at the EIM or Wireless Adapter, and make sure the "onnected" light is flashing green. If the "onnected" light does not flash, make sure no other edlink devices are in Wireless Setup mode, then try again. If the power light at the wireless adapter does not turn on, consult the TrueZONE manual for help. M94 "onnected" status light Green flashing: In Wireless Setup mode. Green steady: edlink device(s) are communicating. ed: edlink device(s) not communicating. heck EIM and edlink devices. While the EIM light is flashing, press NEXT to link the thermostat with the EIM. After a brief delay, the screen will display "Device onnected." At any screen you can press HELP for more information, or press AK to change earlier options

6 System Installation Guide 5 Link optional accessories to wireless network While the Add Device screen is displayed on the thermostat, press and release the ONNET button on each wireless device, as described below. Accessories need to be at least feet away from the thermostat or EIM during the linking process. Press DONE after all devices have been linked If you need to return to the "Add Device" screen to add devices later, press MENU and scroll down to press INSTALLE OPTIONS. Enter the date code (password) when prompted. The date code is printed on the back of the thermostat; or press MENU > EQUIPMENT STATUS to find the date code. After you enter the password, scroll down to press WIELESS DEVIE MANAGE and then select ADD DEVIE. Wireless outdoor sensor Wireless indoor sensor M94 M95 M8847A Press and release ONNET. After a short delay the thermostat will display "Wireless Outdoor Sensor added" on the Add Device screen. Portable omfort ontrol Press and release ONNET. After a short delay, the status light will glow green for 5 seconds. If the status light turns red, the sensor did not link with the thermostat. In normal operation, this light remains off. If it begins flashing red, batteries are low (power will be depleted after weeks). ONNET WIELESS SETUP M94 Press ONNET on the Portable omfort ontrol display screen. Press DONE when the screen displays "onnected," then exit or continue to link another thermostat. Error messages: E 9 Incompatible device cannot be connected. E 4 Low F signal. Move device to a different location and try again. E 8 Make sure the thermostat or the EIM is in Wireless Setup mode, and the Portable omfort ontrol is at least feet away (600 mm). The linking procedure will time out if there is no keypress for 0 minutes. To begin again, press and hold in the lower right corner of the screen until the display changes (about seconds). edlink Internet Gateway M958A Press and release the button on the bottom of the Internet Gateway. After a short delay, the edlink status light will glow steady green M94 6 The Internet Gateway must be registered online before use at Enter the MA ID and MA numbers located on the bottom of the Internet Gateway. For additional information, see instructions provided with the device.

7 THX9/94 Prestige IAQ and F EIM 6 Install optional sensors [If no sensors are used, skip to Section 7.] To install outdoor air sensor Mount the sensor on a vertical exterior wall, at least 6 inches below any overhang. hoose a location protected from direct sunlight. Place sensor securely in bracket, facing away from wall. M849 M8849A To install indoor air sensor emove the wallplate and mount it 4 to 6 feet above the floor on an interior wall. Drill /6-inch holes for drywall, 7/-inch for plaster. Attach sensor securely to wallplate as shown. M96A 7 Setup Installer options (ISU) To setup the thermostat, press MENU and scroll down to press INSTALLE OPTIONS. Enter the date code (password) when prompted. The date code is printed on the back of the thermostat; or press MENU > EQUIPMENT STATUS to find the date code. After you enter the password, press EATE SETUP to setup the thermostat. A brief summary of installer options follows (pages 8 9). You can download a complete list of all options at

8 System Installation Guide 7 Setup Installer options (ISU) - continued TIP: You can use the thermostat US port to download all system configuration and installer options, including your company name and contact information. You can upload this data to each thermostat you install, to save time. : esidential : ommercial : oth ISU Function ISU Function reate Setup: Press EATE SETUP to set all system settings one by one. View/Edit urrent Setup: Press VIEW/EDIT UENT SETUP to select a specific function and make quick changes. Set Up Diagnostics: Press SET UP DIAGNOSTIS to setup and test Delta T diagnostics. Installer Test: Press INSTALLE TEST to quickly determine if the heat, cool, fan and thermostat are operating properly. Minimum off timers are ignored during the test. Data Logs: Press DATA LOGS to view the Alerts Log and User Interactions Log. Wireless Device Manager: Press WIELESS DEVIE MANAGE to add or remove wireless accessories. Advanced Options: Press ADVANED OPTIONS to setup the thermostat using a US device or to restore the thermostat to the factory default settings. Thermostat functions marked in gray below require an EIM (see page ). 000 Language 00 esidential/ommercial 00 Zone Number 00 Device Name 00 Device Name on Home Screen 040 Programmable/Non-programmable 050 Fahrenheit/elsius 060 Outdoor Air Sensor 000 Heating System Type 00 Heating Equipment Type Heat Stages 050 Geothermal Forced Air System 060 eversing Valve O/ ool/ompressor Stages 0 Fan Operation in Heat 0, 80 ackup Heat Type 0, 70 ackup Heat Stages 40 Entry/Exit emote - 50, 00 ackup Heat Operation Home/Occupied ool Setpoint 60, 0 ackup Heat Fan Operation 40 Entry/Exit emote - 90 External Fossil Fuel Kit Home/Occupied Heat Setpoint 0 A-L/A Terminal Setup 40 Entry/Exit emote Manual/Auto hangeover Away/Unoccupied ool Setpoint 000 Auto hangeover Deadband 40 Entry/Exit emote - 00 Temperature ontrol Options Away/Unoccupied Heat Setpoint 00 Finish With High ool Stage 440 Entry/Exit emote - 0 Finish With High Heat Stage Vacation/Holiday ool Setpoint 00 Staging ontrol - ool Differentials 440 Entry/Exit emote Staging ontrol - Heat Differentials Vacation/Holiday Heat Setpoint 080, 090 Staging ontrol - ackup Heat Differentials 0 ackup Heat Upstage Timer 0 Outdoor ompressor Lockout 0 Outdoor ackup Heat Lockout 0, 50 Heat ycles Per Hour 40 ool ycles Per Hour 60 ackup Heat ycles Per Hour ooling Derivative, Integral, Throttling range Heating Derivative, Integral, Throttling range 0 Minimum ompressor Off Time 60 Extended Fan un Time in ool 60 Extended Fan un Time in Heat 4000 Number of Scheduled Periods 400 Pre-occupancy Purge Duration 400 Override: Standard or Initiate Occupancy 400 Override Duration 4050 Minimum ecovery Settings - Heat 4060 Maximum ecovery Settings - Heat 4070 Minimum ecovery Settings - ool 4080 Maximum ecovery Settings - ool 4090 Adaptive Intelligent ecovery 400 Minimum ool Setpoint 400 Maximum Heat Setpoint 40 Keypad Lockout 5000 Select Wired Sensors 500 Indoor Temperature Sensor Name 500 Terminals Wired to Indoor Sensor 500 Indoor Temperature Sensor Type 5040 Indoor Sensors Used for Temperature ontrol 5050 Terminals Wired to Outdoor Sensor 5070 Terminals Wired to eturn Air Sensor 5080 eturn Air Sensor Type

9 THX9/94 Prestige IAQ and F EIM 7 Installer options (ISU) - continued ISU Function ISU Function Thermostat functions marked in gray below require an EIM (see page ) Terminals Wired to Discharge Air Sensor 500 Discharge Air Sensor Type 50 A-oil Low Temperature utoff 6000 Select the Dry ontacts in the System 600 Terminals Wired to emote Setback Dry ontact 600 emote Setback Dry ontact Setup 600 emote Setback Time Delay 6040 emote Setback - Standby ool Setpoint 6040 emote Setback - Standby Heat Setpoint 6050 Terminals Wired to Full Drain Pan Alert Dry ontact 6060 Full Drain Pan Alert Dry ontact Setup 6070 Terminals Wired to Dirty Filter Alert Dry ontact 6080 Dirty Filter Alert Dry ontact Setup 6090 Terminals Wired to Water Leak Alert Dry ontact 600 Water Leak Alert Dry ontact Setup 60 Terminals Wired to System Shutdown Alert Dry ontact 60 System Shutdown Alert Dry ontact Setup 60 Terminals Wired to Service Needed Alert Dry ontact 640 Service Needed Alert Dry ontact Setup 650 Terminals Wired to Fan Failure Alert Dry ontact 660 Fan Failure Alert Dry ontact Setup 670 Terminals Wired to ustom Alert Dry ontact 680 ustom Alert Dry ontact Setup 690, 600 ustom Alert Name and Message 7000 Filter Type 700 Number of Air Filters 70 Air Filter eplacement eminder 70 Air Filter eplacement eminder 70 EA ell leaning eminder 70 EA Pre-Filter leaning eminder 70 EA Post-Filter eplacement eminder 8000 Humidifier Type 800 Indoor Sensor Used for Humidification ontrol 800 Terminals Wired to the Humidifier 8050 Humidification - Window Protection 8060 System Modes Allowing Humidification 8070 Humidification ontrol 8080 Humidifier Lockout 800 lean Tank / Water Filter eplacement eminder 800 Humidifier Pad eplacement eminder 9000 Dehumidification Equipment 900 Indoor Sensor Used for Dehumidification ontrol 900 Humidity Sensor Displayed on the Home Screen 9040 Terminals Wired to Dehumidification Equipment 9050 A/ with Low Speed Fan Setup 9050 Hot Gas ypass Setup 9070 Dehumidification - Overcooling Limit 9080 Dehumidification ontrol 9090 Dehumidification Minimum On Time 900 High Humidity omfort eset Setting 90 System Modes Allowing Dehumidification 90 Dehumidifier Fan ontrol 940 Dehumidifier Lockout 980 Dehumidification Away Mode 990 Dehumidification Away Mode - Fan ontrol 900 Dehumidification Away Mode - Low Limit Temperature 900 Dehumidification Away Mode - Temperature Setting 900 Dehumidification Away Mode - Dehumidification Setting 90 Dehumidifier Filter eplacement eminder 0000 Ventilation Type 000 Terminals Wired to Ventilator/Fresh Air Damper 0050 Ventilation ontrol Method 0060 Ventilation Fan ontrol 0090 Number of edrooms 0090 Size of House 000 Enter Equipment Ventilation ate 00 Ventilation Percent On Time 05 Ventilation Priority 00 Ventilation Low Temperature Lockout 00 Ventilation High Temperature Lockout 00 Ventilation High Dewpoint Lockout 040 Lockout Ventilation on Hum/Dehum alls 060 Ventilate on High Indoor Humidity 070 Ventilator ore leaning eminder 070 Ventilator Filter leaning eminder 000 Number of UV Devices 050 UV ulb eplacement eminder 050 UV ulb eplacement eminder 000 Installer ustom eminders 000 Heat Delta T Diagnostics 00 ool Delta T Diagnostics 05 Set Advanced Delta T Diagnostic Options 00 Allow Delta T Diagnostics During Humidification 00 Allow Delta T Diagnostics During Dehumidification 040 Allow Delta T Diagnostics During Ventilation Allow Heat Delta T Diagnostics: Temp & Humidity Allow ackup Heat Delta T Diagnostics: Temp & Humidity 0-60 Allow ool Delta T Diagnostics: Temp & Humidity 70 Defrost ycle 80 Delta T Alert Sensitivity 90 Display Delta T Alerts to User 4000 lock Format 400 Daylight Saving Time 400 Indoor Temperature Display Offset 400 Indoor Humidity Display Offset Dealer name, phone, , website, message

10 System Installation Guide EIM wiring guide conventional systems Typical wiring of a conventional system with up to -stage heat and -stage cool with one transformer. FUNAE EIM TO THEMOSTAT TANSFOME 0 STATUS LEDS POWE HEAT OOL FAN U ONV A 4 HEAT STAGE W W HEAT STAGE W HEAT STAGE G FAN Y Y OMPESSO STAGE OMPESSO STAGE JUMPES SENSOS ONNET OPTIONAL SENSOS TO S AND S TEMINALS (MAX. SENSOS) M945A 4 See guides on following pages for thermostat wiring and geothermal radiant heat wiring. Wire a maximum of sensors using the S and S terminals. See ISU for options. S and S terminals can be connected to an indoor sensor, outdoor sensor, discharge sensor, return sensor, dry contact device to display an alert or an occupancy sensor for remote setback. emove jumper(s) if using separate transformers. See Economizer wiring section. See following pages for additional thermostat wiring guidelines for heat pumps, geothermal systems and optional Economizer

11 EIM wiring guide heat pump systems THX9/94 Prestige IAQ and F EIM Typical wiring of a heat pump system with up to four-stage heat and two-stage cool with one transformer. EIM TO THEMOSTAT STATUS LEDS POWE HEAT OOL FAN U HEAT PUMP O/ AUX AUX L/A O/ AUX AUX Y HANGEOVE VALVE AKUP HEAT STAGE AKUP HEAT STAGE OMPESSO STAGE Y OMPESSO STAGE G FAN ELAY L/A OMPESSO MONITO O ZONE PANEL JUMPES AI HANDLE TANSFOME 0 SENSOS ONNET OPTIONAL SENSOS TO S AND S TEMINALS (MAX. SENSOS) M946A See guides on following pages for thermostat wiring and geothermal radiant heat wiring. Wire a maximum of sensors using the S and S terminals. See ISU for options. S and S terminals can be connected to an indoor sensor, outdoor sensor, discharge sensor, return sensor, dry contact device to display an alert or an occupancy sensor for remote setback. L/A terminal sends continuous output when thermostat is set to EM HEAT mode, except when set up for Economizer or TOD. See Economizer wiring section

12 System Installation Guide EIM wiring guide geothermal radiant heat Typical wiring for geothermal radiant heat, geothermal forced-air, and backup heat with one transformer. See page 9 for operation. EIM TO THEMOSTAT STATUS LEDS POWE HEAT OOL FAN U HEAT PUMP O/ AUX AUX L/A O/ AUX AUX HANGEOVE VALVE AKUP HEAT STAGE AKUP HEAT STAGE OMPESSO STAGE OMPESSO STAGE FAN ELAY OMPESSO MONITO O ZONE PANEL Y Y G L GEOTHEMAL ADIANT HEAT STAGE OPTIONAL JUMPE AI HANDLE TANSFOME 0 JUMPES SENSOS ONNET OPTIONAL SENSOS TO S AND S TEMINALS (MAX. SENSOS) M947A, or U terminals must be used for geothermal radiant heat (ISU 00). Thermostat allows stages of radiant heat geothermal (stage ) and boiler (stage ). U terminals are normally open dry contacts when set up for geothermal radiant heat. You must install a field jumper if radiant heat is powered by system transformer. Do NOT install a field jumper if radiant heat has its own transformer. L/A terminal sends continuous output when thermostat is set to EM HEAT mode except when set up for Economizer or TOD. See Economizer wiring section

13 Thermostat wiring guides Prestige THX9 THX9/94 Prestige IAQ and F EIM Typical wiring of a -heat / -cool heat pump system with one transformer Typical wiring of a -heat / -cool conventional system with one transformer Transformer 0 Transformer 0 O/ AUX/E Y Y HANGEOVE VALVE AKUP HEAT OMPESSO STAGE OMPESSO STAGE c Thermostat W W Y Y HEAT STAGE HEAT STAGE OMPESSO STAGE OMPESSO STAGE 5 c Thermostat G L/A K 6 FAN ELAY OMPESSO MONITO O ZONE PANEL M948 G A K 6 FAN ELAY M949A Typical wiring of a -heat / -cool heat pump system with two transformers (example - oil forced air backup heat) Typical wiring for geothermal radiant heat, geothermal forced-air and backup heat with one transformer. See page 9 for operation. Air Handler Transformer 0 Transformer 0 O/ AUX/E Y Y G L/A K 6 ackup Heat Transformer HANGEOVE VALVE OMPESSO STAGE OMPESSO STAGE FAN ELAY OMPESSO MONITO O ZONE PANEL 0 c Thermostat AKUP HEAT M950A O/ AUX/E Y Y G L/A K 6 HANGEOVE VALVE AKUP HEAT OMPESSO STAGE OMPESSO STAGE FAN ELAY OMPESSO MONITO O ZONE PANEL 4 GEOTHEMAL ADIANT HEAT STAGE c Thermostat M95A and terminals are dry contacts. L/A terminal sends continuous output when thermostat is set to EM HEAT mode except when set up for Economizer or TOD. See Economizer wiring section. or terminals must be used for geothermal radiant heat (ISU 00). Thermostat allows stages of radiant heat geothermal (stage ) and boiler (stage ). "U" terminals are normally open dry contacts when set up for geothermal radiant heat. You must install a field jumper if radiant heat is powered by system transformer. Do NOT install a field jumper if radiant heat has its own transformer. emove jumper if using separate transformers. onnect the THP9045 Wiresaver Module to the K terminal in heating/cooling applications that do not have a common wire at the thermostat. The K terminal cannot be used in heat-only applications. See THP9045 installation instructions for more information

14 System Installation Guide Prestige THX9 or EIM: Using universal relays to control heating or cooling Powering universal relay with system transformer (THX9 shown) Transformer 0 Powering universal relay with separate heating transformer (THX9 shown) Transformer 0 HEAT STAGE or OOL STAGE or OOL STAGE 4 c Thermostat HEAT STAGE c Thermostat M95A Transformer 0 M95 //U terminals are normally open dry contacts when set up for a stage of heating or cooling. You must install a field jumper if the stage of heating or cooling is powered by system transformer. Do NOT install a field jumper if the stage of heating has its own transformer. //U terminals are assigned to a stage of heating or cooling in the Installer Setup. Options are: THX9 Thermostat ( and ) ool Stage (ISU commercial only) ool Stage 4 (ISU commercial only) onventional Heat Stage (ISU 00, 40) ackup Heat Stage for Heat Pumps (ISU 70) Geothermal adiant Heat (see wiring guide on pages -) THX94 Thermostat with EIM (, and U) ool Stage (ISU commercial only) ool Stage 4 (ISU commercial only) Geothermal adiant Heat (see wiring guide on pages -) Dry ontact Alerts EQUIPMENT DAMAGE HAZAD. Do not apply power to S or S terminals. The dry contact device must be rated for low voltage. If you are not using the S and S terminals on the EIM, you can connect them to a dry contact device to display an alert. Dry contact alerts include Full Drain Pan, Dirty Filter, Water Leak, System Shutdown, Service Needed, Fan Failure and ustom Alert (ISU 6000). EIM ONE DY ONTAT DEVIE MULTIPLE DY ONTAT DEVIES ON ONE SET OF TEMINALS M488 You can connect multiple Dry ontact devices in parallel to the S or S terminals

15 THX9/94 Prestige IAQ and F EIM Wiring guide IAQ equipment (EIM or thermostat) "U" terminals can be used for humidification, dehumidification or ventilation. With power supply Without power supply Typical hookup of powered humidifier. Typical hookup of non-powered humidifier. U U U U POWEED HUMIDIFIE 0 NON-POWEED HUMIDIFIE FIELD INSTALLED JUMPE ETWEEN AND H 0 M9 H 0 M94 Typical hookup of powered ventilation. Typical hookup of non-powered ventilation. U U U U POWEED VENTILATO 0 NON-POWEED VENTILATO FIELD INSTALLED JUMPE ETWEEN AND H 0 M96 H 0 M97 Typical hookup of powered dehumidifier (whole house dehumidifier). Typical hookup of variable speed blower for dehumidification in low speed. U U POWEED DEHUMIDIFIE 0 O U U DEHUMIDIFIATION WITH LOW SPEED FAN FIELD INSTALLED JUMPE ETWEEN AND H 0 M98 H 0 M9 = NOMALLY OPEN, DY ONTATS KEY ANY OMINATION OF UNIVESAL ELAYS (,, U) AN E USED. THEY AE SET IN THE THEMOSTAT INSTALLE SETUP. WIE THE THEMOSTAT O EIM UNIVESAL ELAY TO THE LOW SPEED FAN FO DEHUMIDIFIATION ONTOL AT THE EQUIPMENT. THE THEMOSTAT O EIM ELAY AN E SET TO NOMALLY OPEN O NOMALLY LOSED IN THE THEMOSTAT INSTALLE SETUP. = NOMALLY LOSED, DY ONTATS M

16 System Installation Guide Economizer Module wiring guides Typical wiring of a W70 Economizer Module for a heat pump system, using a Prestige THX9 thermostat or Equipment Interface Module. ooftop Unit W70 Economizer Module (See wiring guidelines provided with the product) O/ N Y Y AUX AUX G SD-O/ O E-GND AUX YI YO YI YO O/ L/A Y Y AUX AUX G Transformer 0 Thermostat/EIM M959A Typical wiring of a W70 Economizer Module for a conventional system, using a Prestige THX9 thermostat or Equipment Interface Module. ooftop Unit W70 Economizer Module (See wiring guidelines provided with the product) N Y Y W W G SD-O/ O E-GND AUX YI YO YI YO A Y Y W W G Transformer 0 Thermostat/EIM M955A A or L/A terminal must be configured for Economizer in the installer setup (ISU 0). These terminals are powered by the cooling transformer (c terminal). Terminal AUX is present only on the Equipment Interface Module

17 THX9/94 Prestige IAQ and F EIM Economizer Module wiring guides Typical wiring of a W7/W74 Economizer Module for a heat pump system, using a Prestige THX9 thermostat or Equipment Interface Module. ooftop Unit O/ N Y Y AUX AUX G W7/W74 Economizer Module (See wiring guidelines provided with the product) O or N 4 & 5 T T O/ L/A Y Y AUX AUX G Transformer 0 Thermostat/EIM M956A Typical wiring of a W7 Economizer Module for a conventional heating system, using a Prestige THX9 thermostat or Equipment Interface Module. ooftop Unit N Y Y W W G W7 Economizer Module (See wiring guidelines provided with the product) N 4 & 5 T T A Y Y W W G Transformer 0 Thermostat/EIM M957A A or L/A terminal must be configured for Economizer in the installer setup (ISU 0). These terminals are powered by the cooling transformer (c terminal). Terminal AUX is present only on the Equipment Interface Module

18 System Installation Guide Economizer and TOD operation (ISU 0) ommercial use only The Economizer can greatly reduce energy costs if configured properly. In some climates the cooling system may run hundreds of hours, when it may not be required to maintain indoor comfort. In some conditions, ventilation with outdoor air can achieve the same level of comfort at lower cost. Tables below explain how the Economizer feature maintains comfort while minimizing costs. Thermostat Mode Equipment Operation A-L/A terminal: Economizer Occupied Heat/ool/Fan running Occupied temporarily Heat/ool/Fan running Occupied Heat/ool/Fan NOT running Occupied temporarily Heat/ool/Fan NOT running Pre-occupancy purge Fan running ON Unoccupied ooling system running Unoccupied temporarily ooling system running Standby ooling system running Unoccupied ooling system NOT running Unoccupied temporarily ooling system NOT running OFF Standby ooling system NOT running Non-programmable Fan running ON Non-programmable Fan NOT running OFF Thermostat Mode A-L/A terminal: TOD Occupied Occupied temporarily Temperature overrides Unoccupied Unoccupied temporarily Standby Non-programmable ON OFF

19 THX9/94 Prestige IAQ and F EIM Heat pump with outdoor temperature lockouts Outdoor temperature lockouts are optional. See Installer Setup options (ISU 0). ackup heat allowed to run with heat pump (see table below) Outdoor temperature Heat pump only Heat pump with backup heat as needed * ackup heat only ackup heat lockout ompressor lockout * No backup heat unless indoor temperature drops to selected ackup Heat Differential setting, or ackup Heat Upstage Timer expires. Heat pump stays ON when backup heat turns on. ackup heat NOT allowed to run with heat pump (see table below) Outdoor temperature Heat pump only Heat pump or backup heat operates * ackup heat only ackup heat lockout ompressor lockout * No backup heat unless indoor temperature drops to selected ackup Heat Differential setting, or ackup Heat Upstage Timer expires. Heat pump turns OFF when backup heat turns on. Heat pump and backup heat operation ackup Heat Type ackup Heat Operation ackup Heat Fan Operation Electric forced air Allowed to run with heat pump Thermostat controls fan Gas or oil forced air NOT allowed to run with heat pump Equipment controls fan Hot water radiant heat Allowed to run with heat pump [n/a] Hot water fan coil Selectable in installer setup Thermostat controls fan Other Selectable in installer setup Selectable in installer setup Geothermal adiant Heat The thermostat can be setup to control Geothermal adiant Heat, Geothermal Forced Air Heat and ackup Heat, all from one thermostat. The thermostat stages the equipment starting with the Geothermal adiant Heat followed by Geothermal Forced Air Heat and then ackup Heat as needed to maintain the desired temperature. The thermostat allows you to set differential temperature settings between each stage if you want the equipment to stage a certain way (see ISU 00 to ISU 090). When the ackup Heat is fossil fuel, the Geothermal Forced Air Heat turns off when the ackup Heat turns on. Geothermal adiant Heat stays on when the fossil fuel ackup Heat turns on. When the ackup Heat is electric, Geothermal adiant Heat and Geothermal Forced Air Heat stay on when the electric ackup Heat turns on. To turn off adiant Heat during the shoulder seasons, install an outdoor reset control and connect to the adiant Heat or switch the thermostat to Emergency Heat mode

20 System Installation Guide asic and Advanced Temperature ontrol Options (ISU 00) asic Options: The Installer Setup displays basic temperature control options which include ackup Heat Differential, ackup Heat Upstage Timer and Outdoor Temperature Lockouts. Note: Outdoor Temperature Lockouts only apply to Heat Pump applications. Advanced Options: The Installer Setup displays both asic and Advanced Options. Advanced temperature control options include Finish With High ool Stage, Finish With High Heat Stage, Temperature Differential settings between all stages and ycle ate settings per stage. Finish With High Heat or ool Stage - When a multi-stage heating or cooling system is used, this feature keeps the high stage of the heating or cooling equipment running until the desired setpoint is reached. ecommended setting for Geothermal Heat Pumps to allow the loop to rest. ackup heat differential and upstage timer A backup heat differential and backup heat upstage timer can be set on any system that has more than one type of heating equipment. See installer setup options (ISU 070-0). Normal operation When the ackup Heat Differential is set to omfort, the thermostat uses backup heat as needed to keep the indoor temperature within F (0.5 ) of the setpoint. When the ackup Heat Differential is set to F or higher, backup heat is not used unless the indoor temperature drops to the ackup Heat Differential setting or the ackup Heat Upstage Timer expires, whichever occurs first. The upstage timer starts when the highest stage of the previous equipment type turns on. Manual temperature change When the ackup Heat Differential is set to omfort, the thermostat uses backup heat as needed to keep the indoor temperature within F (0.5 ) of the setpoint. When the ackup Heat Differential is set to F or higher, if the primary heat is making progress as expected, backup heat will not be used to reach the new setpoint. Set to a higher number to use less backup heat (a greater difference between the current indoor temperature and the new setpoint is required to turn on backup heat). See notes below. Programmed recovery If the primary heat is making progress as expected, backup heat will not be used to reach the setpoint of the next program period. ackup heat is always restricted during a programmed recovery when the Adaptive Intelligent ecovery feature is used. See note below. During a programmed recovery (or when the temperature setpoint is changed by the user), the thermostat waits to turn on the backup heat depending on system performance, load conditions and how many degrees the temperature setpoint is changed. ackup heat will be used ONLY when the temperature is not rising quickly enough to reach the setpoint in a reasonable time. If the backup heat was used in the last hours because the primary heat was not able to maintain the setpoint, the thermostat may turn on the backup heat earlier when the user raises the setpoint. This does NOT apply to heat pumps with fossil fuel backup heat

21 THX9/94 Prestige IAQ and F EIM Humidification The thermostat reads the indoor humidity level and allows the user to set a humidification setting with or without window protection. The thermostat can be setup to control a humidifier in any system mode (Heat, Off, ool [ISU 8060]). A discharge air sensor is required to humidify in the cool mode. Humidification ontrol Options: (ISU 8070) Humidify Only When Heat is On Humidify Only When Fan is On Humidify on Demand: Thermostat ontrols Fan Humidify on Demand: Humidifier ontrols Fan esidential dehumidification The thermostat reads the indoor humidity level and allows the user to set a dehumidification setting. The thermostat controls the humidity level using the cooling system or a whole house dehumidifier. Dehumidification Equipment Options: (ISU 9000) A/ with Low Speed Fan A/ with High Speed Fan Whole House Dehumidifier When set for A/ with Low Speed Fan or A/ with High Speed Fan, an overcooling limit can be set from 0 to F (ISU 9070). The thermostat uses the cooling system to reduce humidity by lowering the temperature up to F below the current cool setpoint until the the desired humidity level is reached. If set for A/ with Low Speed Fan, configure, or U as normally open or normally closed (ISU 9050) and wire the terminal to the Low Speed Fan terminal on the equipment. For example, if the, or U terminal is normally closed, it will open when the thermostat calls for dehumidification. Note: The thermostat will not lower the fan speed when the second stage of cooling is on. The Whole House Dehumidifier option requires a dedicated unit for dehumidification. The thermostat can be setup to control dehumidification in all modes (Heat, Off, ool [ISU 90]). If humidification and dehumidification are setup to operate in the same system mode (Heat, ool, Off), and you are sensing humidity from one location, the thermostat will automatically enforce a 5% deadband between the humidification and dehumidification settings. The thermostat will automatically switch between humidification and dehumidification to maintain the desired humidity level. If humidification and dehumidification are setup to operate in the same system mode (Heat, ool, Off), and you are sensing humidity from two different locations using a remote wireless indoor sensor (for example, main level and crawl space), the thermostat will allow humidification and dehumidification to operate at the same time, and there is no deadband between humidification and dehumidification settings

22 System Installation Guide ommercial dehumidification The thermostat reads the indoor humidity level and allows the user to set a dehumidification setting. The thermostat controls the humidity level using the cooling system or a dehumidifier. Dehumidification Equipment Options: (ISU 9000) A/ with Low Speed Fan A/ with High Speed Fan Hot Gas ypass Dehumidifier When set for A/ with Low Speed Fan, A/ with High Speed Fan or Hot Gas ypass, there are six methods of dehumidification control: (ISU 9080) See descriptions of each, below. asic: This option uses the cooling system to reach the desired humidity level. Minimum On Time, High Humidity omfort eset and eheat are not used with this method. This setting is commonly used if your dehumidification equipment is Hot Gas ypass. Minimum On Time (ISU 9090): This option ensures that the compressor runs long enough to effectively reduce humidity when the cooling equipment is cycled on. The compressor will run for the minimum "on time" you set until the desired humidity level is reached. High Humidity omfort eset (ISU 900): This option uses the cooling system to lower the temperature up to 5 F below the current cool setpoint until the desired humidity is reached. The high humidity comfort range is from to 5 F. 4 High Humidity omfort eset with Minimum On Time (ISU 9090 and 900): This method uses both options above to reduce humidity while maintaining a comfortable temperature. 5 eheat (ISU 9080): This option allows heating to run during dehumidification to help maintain a comfortable temperature. If only cooling stage is used, during the "off" cycle, both cooling and heating run at the same time as needed to dehumidify without overcooling. This option cannot be used in the Heat mode. This option is effective only if using a system with the A-oil located before the heating coil (heat exchanger). 6 eheat with Minimum On Time (ISU 9080 and 9090): This method uses both eheat and Minimum On Time options above to reach the desired humidity level. The Dehumidifier option requires a dedicated unit for dehumidification. The thermostat can be setup to control dehumidification in all modes (Heat, Off, ool [ISU 90]). Hot Gas ypass - During a call for dehumidification, the cooling capacity will be used to remove more latent heat than sensible heat. The operation of Hot Gas ypass varies by equipment. For more details, contact the equipment manufacturer. eheat can be used on heat pump applications that have a forced air backup heat source (gas, oil or electric). The thermostat will turn on the first stage of forced air backup heat during eheat

23 Southern Dehumidification Away Mode THX9/94 Prestige IAQ and F EIM Southern Dehumidification Away Mode protects the home when unoccupied for long periods of time during hot and humid weather by maintaining the desired humidity and temperature settings. Southern Dehumidification Away Mode options: (ISU 980 to 900) Fan ontrol: Auto, On or irculate Low Limit Temperature Setting: The thermostat allows the cooling system to lower the indoor air to the Low Limit Temperature Setting to reach the Dehumidification Setting (ISU 900). Temperature Setting: Temperature that is maintained when dehumidification is not needed. Dehumidification Setting: The desired humidity level while Southern Dehumidification Away Mode is active. You can control humidity with a dehumidifier or a cooling system. If a cooling system is used, humidity is controlled by cooling indoor air to the Low Limit Temperature Setting. When the desired humidity level is reached, the system will maintain the Southern Dehumidification Away Mode temperature setting. Ventilation The thermostat can be set for the following ventilation types: (ISU 0000) EV/HV Passive (Fan Only) Fresh Air Damper Ventilation ontrol Methods (ISU 0050) Ventilation can be setup to meet ASHAE or Percent On Time settings. To meet these settings, the thermostat will ventilate during calls for heat, cool and fan. If the required ventilation has not been achieved for ASHAE or Percent On Time, the thermostat will force the ventilation equipment on. ASHAE: The thermostat operates ventilation equipment to meet the ASHAE 6. ventilation standard based on FM, number of bedrooms, and square footage of the house. ASHAE 6. can only be met if the ventilation equipment is running. If the ventilation equipment is off for any reason (outdoor ventilation lockouts, set up to turn Off during Sleep period, turned off by user etc.), ASHAE 6. is not met during those times. See ISU 05 to select a Ventilation Priority. Percent on Time: The ventilator runs based on a percentage set in the Installer Setup. For example: if set to 50%, the ventilator runs at random times during a hour period until it reaches a 50% run time (approximately 0 minutes)

24 System Installation Guide Indoor sensor operation Temperature control The thermostat can be set to respond to its internal temperature sensor, or to an optional remote indoor sensor. If multiple sensors are used, the thermostat will respond to an average of temperatures detected at each sensor. Humidification control If optional remote indoor sensors are installed, you can choose which sensor you want to use for humidification control. You can use a different sensor for dehumidification. Dehumidification control If optional remote indoor sensors are installed, you can choose which sensor you want to use for dehumidification control. For example, you can use one sensor for humidification control, and another for dehumidification. Wireless indoor sensor attery level indicators (when batteries are inserted) Good: Status light flashes green for 5 seconds. Low: Status light flashes red for 5 seconds. Use fresh batteries. attery level indicators (during use) Good: Status light remains off. Low: attery power will be depleted in about months. Thermostat displays Low attery warning. Status light remains off. ritical: attery power will be depleted in about weeks. Status light flashes red. The Wireless Indoor Sensor is compatible only with edlink.0 thermostats. The thermostat can use up to 6 optional wireless sensors

25 THX9/94 Prestige IAQ and F EIM Alerts and diagnostics Maintain close contact with your customers by providing more comfort and efficiency with alerts and diagnostics. Alerts and reminders can notify customers when maintenance or service is needed, and display your contact information to make it easy for them to reach you. The following are only a few of many options. heck the thermostat's on-screen menus for more. Alerts Log MENU > INSTALLE OPTIONS > DATA LOGS > ALETS LOG The thermostat saves the most recent 5 alerts. It records the date, time, alert status (snoozed, dismissed, recovered), and diagnostic information to help you identify and correct problems. User Interactions Log MENU > INSTALLE OPTIONS > DATA LOGS > USE INTEATIONS LOG heck this log to find out if a problem was caused by an accidental user error. The log shows most changes made to thermostat settings, by time and date, and describes what change was made. The thermostat records the most recent 50 changes. You can quickly search them by date and time, or by function. This feature can be turned off if necessary, so that no user interactions are recorded. Examples: * [date, time] Heat temperature set to 80 F * [date, time] System mode set to Off * [date, time] Installer setup changed heating equipment type Delta T Diagnostics MENU > INSTALLE OPTIONS > SET UP DIAGNOSTIS If a discharge and return air sensor is installed, the thermostat can track system performance over time. It measures this as "Delta T." This can tell you if the system is performing above or below expected standards which would normally go unnoticed, and may cause unnecessary energy use. It can also detect and warn about problems early, before heating or cooling equipment fails. The thermostat will measure and record Delta T of the system for each stage you test. This information can be used to set the proper Delta T fault limits of the system. When the system operates outside those limits multiple times, an alert is recorded in the log. If configured to do so, the system will then display an alert to the user. Delta T Alert Sensitivity is adjustable in the Installer Setup (ISU 80) Delta T diagnostics is only for non-zoned forced air systems

26 System Installation Guide eplacing system components To replace an Equipment Interface Module (EIM) Follow steps below to disconnect the thermostat and edlink accessories. See pages 5-6 to re-link devices. At the Thermostat Press MENU > INSTALLE OPTIONS, then enter date code when prompted (printed on back of thermostat). Or press MENU > EQUIPMENT STATUS to find the date code. Scroll down to select WIELESS DEVIE MANAGE. Press EMOVE DEVIE, then select THIS THEMOSTAT to remove. At the Portable omfort ontrol Press and hold the blank space (or arrow if present) in the lower right hand corner of the screen until the display changes. Press EMOVE, then YES to disconnect from the old EIM. At the Indoor Sensor, edlink Internet Gateway, Entry/Exit emote, Vent oost emote or TrueSTEAM Wireless Adapter Press and hold the ONNET button on the edlink accessory until the status light glows amber (hold for about 0 seconds). This will disconnect the device from the old EIM or thermostat. To replace a thermostat At the EIM (Skip this step if no EIM is used) Press and hold the ONNET button on the EIM until the status light glows amber (hold for about 0 seconds). This will disconnect ALL devices from the EIM. At the Portable omfort ontrol Press and hold the blank space (or arrow if present) in the lower right hand corner of the screen until the display changes. Press EMOVE, then YES to disconnect from the old thermostat. At the Indoor Sensor, edlink Internet Gateway, Entry/Exit emote, Vent oost emote or TrueSTEAM Wireless Adapter Press and hold the ONNET button on the edlink accessory until the status light glows amber (hold for about 0 seconds). This will disconnect the device from the old thermostat. To remove accessories from an EIM or thermostat At the Thermostat Press MENU > INSTALLE OPTIONS, then enter date code when prompted (print on back of thermostat). Or press MENU > EQUIPMENT STATUS to find the date code. Scroll down to select WIELESS DEVIE MANAGE. Press EMOVE DEVIE, then select the device you want to remove. O: At the EIM M958A Press and hold in lower right corner of screen Press and hold the ONNET button on the EIM until the status light glows amber (hold for about 0 seconds). This will disconnect ALL devices from the EIM. If the THX9 thermostat is setup without an EIM, all thermostat settings must be reset before it can be used with an EIM. Press MENU > INSTALLE OPTIONS, scroll down to select ADVANED OPTIONS, then press ESTOE FATOY DEFAULTS

27 THX9/94 Prestige IAQ and F EIM Specifications & replacement parts Operating Ambient Temperature Thermostat: to 0 F (0 to 48.9 ) Portable omfort ontrol: to 0 F (0 to 48.9 ) Wireless Outdoor Sensor: -40 to 40 F (-40 to 60 ) Wireless Indoor Sensor: 0 to 0 F (-7.8 to 48.9 ) For Optimal attery Life: 5 to 4 F (.7 to 45.6 ) Equipment Interface Module: -40 to 65 F (-40 to 7.9 ) eturn Air Sensor: 0 to 00 F (-7.8 to 9. ) Discharge Air Sensor: 0 to 00 F (-7.8 to 9. ) edlink Internet Gateway: to 0 F (0 to 48.9 ) Operating elative Humidity Thermostat: 5% to 90% (non-condensing) Portable omfort ontrol: 5% to 90% (non-condensing) Wireless Outdoor Sensor: 0% to 00% (condensing) Wireless Indoor Sensor: 5% to 90% (non-condensing) Equipment Interface Module: 5% to 95% (non-condensing) edlink Internet Gateway: 5% to 95% (non-condensing) Physical Dimensions (height, width, depth) Thermostat: -7/8 x 6-/6 x -7/6 inches (99 x 7 mm x 6 mm) Equipment Interface Module: 9-5/6 x 4-/6 x -9/ inches (9 x 47 x 4 mm) Wireless Outdoor Sensor: 5 x -/ x -/6 inches (7 x 89 x 4 mm) Wireless Indoor Sensor: -7/8 x -7/8 x 5/6 inches (74 x 48 x mm) Portable omfort ontrol: 6-/4 x -/8 x -5/8 inches (58 x 80 x 8 mm) edlink Internet Gateway: 6 x 4-7/8 x -/ inches (5 x x 64 mm) Electrical atings Terminal Voltage (50/60 Hz) Max. urrent ating W - O/ 8 to 0.00A W - O/ (EIM only) 8 to 0 and 750 mvd.00a Y (cooling) 8 to 0.00A G (fan) 8 to A W - Aux (heating) 8 to A Y (cooling) 8 to A W - Aux 8 to 0.00A A-L/A (Output) 8 to 0.00A, 0 max. 0.50A, 0 max. 0.50A U, U 0 max. 0.50A Accessories & eplacement Parts Item Part Number Equipment Interface Module THM540 edlink Internet Gateway THM Wireless Entry/Exit emote EM00000 Wireless Vent and Filter oost emote HV0A000 Portable omfort ontrol EM Occupancy Sensor for emote Setback WSK- Wireless Outdoor Sensor Wireless Indoor Sensor Wired Outdoor Sensor 0k ohm NT Wired Wall-mount Indoor Sensor 0k ohm NT Wired Flush-mount Indoor Sensor 0k ohm NT 777A004, 777A0 Wired Wall-mount Indoor Sensor 0k ohm NT T Wired Wall-mount Indoor Sensor 0k ohm NT T-A Discharge or eturn Air Sensor 0k ohm NT 775A000 Discharge or eturn Air Sensor 0k ohm NT 704 Discharge or eturn Air Sensor 0k ohm NT 7770A006 over Plate (covers marks left by old thermostats) attery Pack (For demo use only) THP000A007 Wire Saver Module THP9045A

Control for up to 4 Heat/2 Cool heat pump systems or up to 3 Heat/2 Cool conventional systems for residential and commercial applications.

Control for up to 4 Heat/2 Cool heat pump systems or up to 3 Heat/2 Cool conventional systems for residential and commercial applications. THX9/94 Prestige IAQ and F EIM With wireless accessories System Installation Guide ontrol for up to 4 Heat/ ool heat pump systems or up to Heat/ ool conventional systems for residential and commercial

More information

Installation Guide. Prestige IAQ with Equipment Interface Module. RedLINK to Equipment Interface Module. RedLINK to TrueZONE Wireless Adapter

Installation Guide. Prestige IAQ with Equipment Interface Module. RedLINK to Equipment Interface Module. RedLINK to TrueZONE Wireless Adapter TM TM TM Prestige IAQ with Equipment Interface Module Installation Guide edlink to Equipment Interface Module 2 Wires for Power O edlink to TrueZONE Wireless Adapter 2 Wires for Power eference to key features

More information

VisionPRO Series with RedLINK. Installation Guide

VisionPRO Series with RedLINK. Installation Guide VisionPRO Series with RedLINK Installation Guide Reference to key features * Password is the date code. Current display. Underlined label signifies the current display. Mode control buttons. Use to change

More information

Installation Guide. Wi-Fi VisionPRO Reference to key features

Installation Guide. Wi-Fi VisionPRO Reference to key features Wi-Fi VisionPO 8000 Installation Guide eference to key features * Password is the date code. urrent display. Underlined label signifies the current display. Mode control buttons. Use to change settings

More information

Installation Guide. VisionPRO Series with RedLINK. Wired Directly to Equipment. OR RedLINK to TrueZONE Wireless Adapter

Installation Guide. VisionPRO Series with RedLINK. Wired Directly to Equipment. OR RedLINK to TrueZONE Wireless Adapter TM TM TM VisionPO Series with edlin Installation uide Wired Directly to Equipment Dual Powered - Wire or Battery ( wire or Wire Saver required to use edlin accessories) O edlin to Equipment Interface Module

More information

Installation Guide. VisionPRO. TH8000 Series. Need Help? This manual covers the following models. System Types

Installation Guide. VisionPRO. TH8000 Series. Need Help? This manual covers the following models. System Types Installation Guide VisionPRO TH8000 Series Touch-screen Programmable Thermostat This manual covers the following models TH8110U: For 1 Heat/1 Cool systems TH8320U: For up to 3 Heat/2 Cool systems TH8321U:

More information

Alerts and Delta T Diagnostics with the Prestige 2.0 IAQ Thermostat

Alerts and Delta T Diagnostics with the Prestige 2.0 IAQ Thermostat Alerts and Delta T Diagnostics with the Prestige 2.0 IAQ Thermostat MOUNTING LOCATIONS Refer to the guidelines below and Fig. 1 5 for mounting locations of the Discharge and Return Air Temperature Sensors.

More information

THX9321 Prestige 2.0 and. THX9421 Prestige IAQ with EIM APPLICATION FEATURES PRODUCT DATA

THX9321 Prestige 2.0 and. THX9421 Prestige IAQ with EIM APPLICATION FEATURES PRODUCT DATA THX9321 Prestige 2.0 and THX9421 Prestige IAQ with EIM PRODUCT DATA Delta T Alerts and Diagnostics Alerts give customers a sense of security while allowing you to service or replace the equipment prior

More information

Installation Guide. LR-HWLV-HVAC TouchPRO Wireless. System Types

Installation Guide. LR-HWLV-HVAC TouchPRO Wireless. System Types Installation Guide LR-HWLV-HVAC TouchPRO Wireless Touchscreen Thermostat System Types Gas, oil, or electric heat with air conditioning Warm air, hot water, high efficiency furnaces, heat pumps, steam,

More information

Safety & Installation Instructions

Safety & Installation Instructions 8400 Series Thermostats Safety & Installation Instructions READ AND SAVE THESE INSTRUCTIONS 61000652D 8400 Tstat Install.indd 1 Table of contents Installation Installation location recommendations... 3

More information

Installation Guide TH3210D. Non-programmable Digital Thermostat

Installation Guide TH3210D. Non-programmable Digital Thermostat Installation Guide TH3210D Non-programmable Digital Thermostat Product Application This thermostat provides electronic control of 24 VAC heat pump systems with auxiliary heat (2 heat/1 cool). Power Type

More information

Installation Guide TH4210D. Programmable Thermostat

Installation Guide TH4210D. Programmable Thermostat Installation Guide TH4210D Programmable Thermostat Product Application This thermostat provides electronic control of 24 VAC heat pump systems with auxiliary heat (2 heat/1 cool). Power Type Battery power

More information

Controller Kit Installation Manual MIFH1, MRCH1, MCCH1, MOS1

Controller Kit Installation Manual MIFH1, MRCH1, MCCH1, MOS1 Controller Kit Installation Manual MIFH1, MRCH1, MCCH1, MOS1 Installation guide for: Wireless Receiver and Cable (MIFH1) Remote Controller (MRCH1) Portable Central Controller (MCCH1) Outdoor Air Sensor

More information

VisionPRO 8000 with RedLINK

VisionPRO 8000 with RedLINK VisionPRO 8000 with RedLINK PRODUCT DATA Customizable Service Reminders Set up to 10 service reminders. Choose from the pre-set options or customize your own. Reminders can be based on date or the outdoor

More information

Installation Guide TH3110D. Non-programmable Digital Thermostat

Installation Guide TH3110D. Non-programmable Digital Thermostat Installation Guide TH3110D Non-programmable Digital Thermostat Product Application This thermostat provides electronic control of 24 VAC single-stage heating and cooling systems, or 750 mv heating systems.

More information

Safety & Installation Instructions

Safety & Installation Instructions Home omfort ontrol Model 8910 READ AND SAVE THESE INSTRUTIS Safety & Installation Instructions Table of contents Installation Thermostat installation location recommendations.. 2 Thermostat mounting...

More information

Installation Guide TH4110B. Programmable Thermostat

Installation Guide TH4110B. Programmable Thermostat Installation Guide TH4110B Programmable Thermostat Product Application This thermostat provides electronic control of 24 VAC single-stage heating and cooling systems, or 750 mv heating systems. System

More information

Installation Guide TH5220D. Non-programmable Digital Thermostat

Installation Guide TH5220D. Non-programmable Digital Thermostat Installation Guide TH5220D Non-programmable Digital Thermostat Product Application This thermostat provides electronic control of 24 VAC single-stage and multi-stage heating and cooling systems, or 750

More information

Smart Energy Programmable Thermostat + Energy Monitor. EE542-1Z I Installation Manual

Smart Energy Programmable Thermostat + Energy Monitor. EE542-1Z I Installation Manual Smart Energy Programmable Thermostat + Energy Monitor EE542-1Z I Installation Manual 1 2 3 3 4 6 9 14 17 19 20-22 Back Cover Contents Introduction Getting Started Installing the Thermostat Quick Guide

More information

RedLINK Wireless Comfort Systems. RedLINK Connects.

RedLINK Wireless Comfort Systems. RedLINK Connects. RedLINK Wireless Comfort Systems RedLINK Connects. TM THERMOSTATS ZONING AIR CLEANERS HUMIDIFIERS DEHUMIDIFIERS UV SYSTEMS VENTILATION WATER SOLUTIONS wireless TM Your Customers Are Connected. Wireless.

More information

Install Guide 3M-50. Caution. Caution

Install Guide 3M-50. Caution. Caution PG 1 Install Guide 3M-50 aution Your thermostat is a precise instrument, handle it with care. Turn off electricity to the HVA system before installing or servicing thermostat or any part of the system.

More information

Sensi TM. Wi-Fi Programmable Thermostat MANUAL OPERATION. Version: March 2016 2016 Emerson Electric Co. All rights reserved.

Sensi TM. Wi-Fi Programmable Thermostat MANUAL OPERATION. Version: March 2016 2016 Emerson Electric Co. All rights reserved. Sensi TM Wi-Fi Programmable Thermostat MANUAL OPERATION Version: March 2016 2016 Emerson Electric Co. All rights reserved. Contents MANUAL OPERATION GUIDE Buttons and Icons 3 Basic Functionality 4 Manual

More information

INSTALLATION MANUAL. Room thermostat EKRTR EKRTETS

INSTALLATION MANUAL. Room thermostat EKRTR EKRTETS INSTALLATION MANUAL EKRTR EKRTETS 1 2 1 2 3 60 87 170 161 ±1.5 m >0.2 m 3 5 4 34 125 4 5 28 50 EKRTR EKRTETS Contents Read this manual attentively before starting up the unit. Do not throw it away. Keep

More information

Safety & Installation Instructions

Safety & Installation Instructions Home omfort ontrol with i-fi Model 8910 READ AND SAVE THESE INSTRUTIS Safety & Installation Instructions Table of contents I-FI Setup i-fi Setup... 2 Installation Thermostat installation location recommendations..

More information

RESIDENTIAL THERMOSTATS CLIMATEMASTER

RESIDENTIAL THERMOSTATS CLIMATEMASTER ESIDENTIAL THEMSTATS LIMATEMASTE ETHEMAL HEATIN AND LIN MFT SYSTEMS ESIDENTIAL THEMSTAT PDUT UIDE THE LBAL LEADE esidential Thermostats 3.30 in [83.8mm] Fan: turns continuous fan FF or N 0.8 in Depth

More information

Wireless and Prestige Comfort Systems. Frequently Asked Questions Guide

Wireless and Prestige Comfort Systems. Frequently Asked Questions Guide Wireless and Prestige Comfort Systems Frequently sked uestions Guide TM RedLINK Wireless Technology TM The Description What is RedLINK? RedLINK is the first wireless protocol developed specifically for

More information

LX Series. Owner s Manual. Digital Thermostat. Digital Thermostat. Installation Instructions. and

LX Series. Owner s Manual. Digital Thermostat. Digital Thermostat. Installation Instructions. and LX Series Digital Thermostat Digital Thermostat Model S1-THSU21P1 S1-THSU32P7 S1-THSU32HP7 RESIDENTIAL BACKLIT DISPLAY Owner s Manual and Installation Instructions CAUTION Follow the Installation Instructions

More information

NeW. User's Manual Quick Start Installation. Application. Features 110-1043B. 2 Heat / 2 Cool

NeW. User's Manual Quick Start Installation. Application. Features 110-1043B. 2 Heat / 2 Cool DIGITAL 9415 NON-PROGRAMMABLE THERMOSTAT NeW G E O GAS ELECTRIC OIL 2 Heat / 2 Cool User's Manual Quick Start Installation 110-1043B Application The Robertshaw 9415 is a multi-stage thermostat designed

More information

COMFORT CONTROL - 4 HEAT (GAS, OIL*, OR ELECTRIC)/3 COOL/HEAT PUMP COMMUNICATING PROGRAMMABLE 3 WIRE HOOKUP

COMFORT CONTROL - 4 HEAT (GAS, OIL*, OR ELECTRIC)/3 COOL/HEAT PUMP COMMUNICATING PROGRAMMABLE 3 WIRE HOOKUP COMFORT CONTROL - 4 HEAT (GAS, OIL*, OR ELECTRIC)/3 COOL/HEAT PUMP COMMUNICATING PROGRAMMABLE 3 WIRE HOOKUP ALL phases of this installation must comply with NATIONAL, STATE, AND LOCAL CODES INSTALLER S

More information

Installation Instructions

Installation Instructions TP-PRH-A, TP-NRH-A Performance Series Edge Thermidistat Control Installation Instructions Programmable Control A07049 A07048 Non Programmable Control Designed and Assembled in the USA. NOTE: Read the entire

More information

Installation Guide. Programmable Thermostat TH6110D

Installation Guide. Programmable Thermostat TH6110D Installation Guide Programmable Thermostat TH6110D Product Application This thermostat provides electronic control of 24 VAC single-stage heating and cooling systems, or 750 mv heating systems. System

More information

Installation Instructions

Installation Instructions Installation Instructions Model TSTATG2111 Use with most systems: 2-Heat, 1-ool 1- Day Prog ram m ab l e Digital Thermostat u p t o 2 - H e a t & 1 - o o l ontrol up to 2 Heat & 1 ool Stages Backlit Display

More information

Installation Guide. Programmable Thermostat TH6220D

Installation Guide. Programmable Thermostat TH6220D Installation Guide Programmable Thermostat TH6220D Product Application This thermostat provides electronic control of 24 VAC single-stage and multi-stage heating and cooling systems, or 750 mv heating

More information

T8511G,R Microelectronic Heat Pump Thermostats

T8511G,R Microelectronic Heat Pump Thermostats T85G,R Microelectronic Heat Pump Thermostats INSTALLATION INSTRUCTIONS APPLICATION The T85 Microelectronic Heat Pump Thermostat provides electronic control of 24 Vac two-stage heating and one-stage cooling

More information

IMPORTANT Read and save these instructions. OWNER S GUIDE. Elite Series Programmable Touch Screen Thermostats

IMPORTANT Read and save these instructions. OWNER S GUIDE. Elite Series Programmable Touch Screen Thermostats 2005 Lennox Industries Inc. Dallas, Texas, USA OWNER S GUIDE Elite Series Programmable Touch Screen Thermostats IMPORTANT Read and save these instructions. 505,045M 1/2005 Table of Contents Thermostat

More information

ENERGY MANAGEMENT SYSTEM Manual

ENERGY MANAGEMENT SYSTEM Manual 2010 ecobee 333 Adelaide Street West 6th Floor Toronto Ontario M5V 15 anada toll free 1.877.932.6233 www.ecobee.com MA-EMS-201-2 ENEY MANAEMENT SYSTEM Manual ONTENTS etting started 2 Welcome 2 HVA System

More information

Communicating Wall Control Installation Manual TSTAT0101SC

Communicating Wall Control Installation Manual TSTAT0101SC Communicating Wall Control Installation Manual TSTAT0101SC U.S. Patent No. 7,243,004 U.S. Patent No. 7,775,452 616 01 1017 02 08/07/12 Safety Considerations... 7 Introduction... 8 Quick Start... 9 Set

More information

User Manual THR840DUK Digital Thermostat

User Manual THR840DUK Digital Thermostat User Manual THR840DUK Digital Thermostat 50051982-001 Rev. A WARNING: This product must be correctly installed and configured to work properly (see pages 12-24). If you are not experienced in wiring electrical

More information

FAQs. Conserve package. Gateway... 2 Range Extender... 3 Smart Plug... 3 Thermostat... 4 Website... 7 App and Mobile Devices... 7

FAQs. Conserve package. Gateway... 2 Range Extender... 3 Smart Plug... 3 Thermostat... 4 Website... 7 App and Mobile Devices... 7 FAQs Conserve package Gateway... 2 Range Extender... 3 Smart Plug... 3 Thermostat... 4 Website... 7 App and Mobile Devices... 7 FAQs Gateway Can I have someone install my system for me? If you are concerned

More information

PRODUCT PRODUCT CODE TECHNICAL INSTRUCTIONS PAGE

PRODUCT PRODUCT CODE TECHNICAL INSTRUCTIONS PAGE Table of Contents PRODUCT PRODUCT CODE TECHNICAL INSTRUCTIONS PAGE # Electric Room Comfort Controller NEW! RDY2000 Room Comfort Controller RDY 129-905 D-3 Electric for Specialized Applications Surface

More information

Installation Instructions

Installation Instructions T2 -PAC, T2 -NAC T2 -PHP, T2 -NHP LEGACYt SERIES THERMOSTATS Installation Instructions A07047 Legacy Series Programmable Thermostat A07046 Legacy Series Non-Programmable Thermostat Designed and Assembled

More information

TF428 Series Digital Thermostat Fan Coil Unit Control

TF428 Series Digital Thermostat Fan Coil Unit Control TF428 Series Digital Thermostat Fan Coil Unit Control Features SPECIFICATION DATA General The TF428 series digital thermostat is designed for 3-speed fan and valve control in a fan coil system, including:

More information

Operating Manual. VisionPRO TH8000 Series EFS-03. Touchscreen Programmable Thermostat

Operating Manual. VisionPRO TH8000 Series EFS-03. Touchscreen Programmable Thermostat Operating Manual VisionPRO TH8000 Series Touchscreen Programmable Thermostat 69-1894EFS-03 BE CAREFUL! Never use sharp instruments, such as a pencil or pen, to press touchscreen keys. To prevent damage

More information

Variable Air Volume - VAV

Variable Air Volume - VAV Mode Enable Sensor Options Variable Air Volume - VAV The temperature of this sensor will determine if the unit is in heating, cooling or vent mode during occupied operation. The following options are available:

More information

Portable Air Conditioner. OWNER S MANUAL Read these instructions before use. Model: MM14CCS. Voltage rating: 115V~60Hz Power rating : 1400W

Portable Air Conditioner. OWNER S MANUAL Read these instructions before use. Model: MM14CCS. Voltage rating: 115V~60Hz Power rating : 1400W Portable Air Conditioner OWNER S MANUAL Read these instructions before use Model: MM14CCS Customer Support : 1-800-474-2147 Voltage rating: 115V~60Hz Power rating : 1400W For product inquiries or support

More information

Operating Manual. Prestige THX9000 Touch-screen Thermostat Thermostat à écran tactile Termostato con pantalla táctil

Operating Manual. Prestige THX9000 Touch-screen Thermostat Thermostat à écran tactile Termostato con pantalla táctil Operating Manual Prestige THX9000 Touch-screen Thermostat Thermostat à écran tactile Termostato con pantalla táctil BE CAREFUL! Never use sharp instruments, such as a pencil or pen, to press touchscreen

More information

Welcome To INSTALLATION GUIDE

Welcome To INSTALLATION GUIDE Welcome To INSTALLATION GUIDE 1 Contents Introduction... 3 In The Box... 4 Display... 5 Before You Start... 6 Installation Overview... 7 Professional Assistance... 7 Abbreviations... 8 Installation Details...

More information

1F Non-programmable Electronic Digital Heat Pump Thermostat INSTALLATION AND OPERATION INSTRUCTIONS

1F Non-programmable Electronic Digital Heat Pump Thermostat INSTALLATION AND OPERATION INSTRUCTIONS 1F89-211 Non-programmable Electronic Digital Heat Pump Thermostat INSTALLATION AND OPERATION INSTRUCTIONS Operator: Save these instructions for future use! FAILURE TO READ AND FOLLOW ALL INSTRUCTIONS CAREFULLY

More information

CONTROLS KITS AND ACCESSORIES. 507240-01 12/2014 Supersedes10/2014

CONTROLS KITS AND ACCESSORIES. 507240-01 12/2014 Supersedes10/2014 2014 Lennox Industries Inc. Dallas, Texas, USA CONTROLS KITS AND ACCESSORIES 507240-01 12/2014 Supersedes10/2014 Litho U.S.A. Equipment Interface Module Installation Instructions for the Equipment Interface

More information

Portable Air Conditioner. OWNER S MANUAL Read these instructions before use. Model: MN12CES / MN10CESWW

Portable Air Conditioner. OWNER S MANUAL Read these instructions before use. Model: MN12CES / MN10CESWW Portable Air Conditioner OWNER S MANUAL Read these instructions before use 8 Model: MN12CES / MN10CESWW Voltage rating: 120V~60Hz Power rating : 1100W (MN12CES) Power rating : 900W (MN10CESWW) Customer

More information

230 V~ Room Thermostat

230 V~ Room Thermostat 230 V~ 369813a 1 07.02.15 The 230 V~ room thermostat adds temperature control to the LutronR hotel guestroom control solution. Controls 2-pipe, 4-pipe, and 3 fan-speed fan coil units. Compatible with LutronR

More information

Heating and Cooling Basics Thermostat Control

Heating and Cooling Basics Thermostat Control Heating and Cooling Basics Thermostat Control UNI-LINE PRODUCT KNOWLEDGE 2012 Invensys. All Rights Reserved. The names, logos, and taglines identifying the products and services of Invensys are proprietary

More information

Installation Guide RTH6300B. Programmable Thermostat

Installation Guide RTH6300B. Programmable Thermostat Installation Guide RTH6300B Programmable Thermostat MERCURY NOTICE: Do not place your old thermostat in the trash if it contains mercury in a sealed tube. Contact your local waste management authority

More information

Commercial Comfort System (CCS) Operation Overview Technical Bulletin

Commercial Comfort System (CCS) Operation Overview Technical Bulletin Commercial Comfort System (CCS) Operation Overview Technical Bulletin Code No. LIT-12011617 Software Release 1.2 Issued July 15, 2011 Supersedes February 23, 2010 Refer to the QuickLIT Web site for the

More information

HEAT HEAT COOL HEAT PUMP COOL

HEAT HEAT COOL HEAT PUMP COOL OWNER S MANUAL RESIDENTIAL THERMOSTAT P/N P374-1800 HEAT COOL HEAT PUMP Su AUTO 0I20: Pm 74 COOL HEAT 27 7-DAY MABLE DIGITAL THERMOSTAT 3 Configurable Outputs Accepts Optional Humidity Module: Control

More information

Portable Air Conditioner. OWNER S MANUAL Read these instructions before use. Model: MF08CESWW. Voltage rating: 115V~60Hz Power rating : 800W

Portable Air Conditioner. OWNER S MANUAL Read these instructions before use. Model: MF08CESWW. Voltage rating: 115V~60Hz Power rating : 800W MODE ALARM Portable Air Conditioner OWNER S MANUAL Read these instructions before use 8 Model: MF08CESWW Voltage rating: 115V~60Hz Power rating : 800W Customer Support : 1-800-474-2147 For product inquiries

More information

USER MANUAL WARNING! CONTENTS MODEL 1 SPECIFICATIONS READ ALL INSTRUCTIONS BEFORE PROCEEDING. Non-Programmable Single Stage Heat/Cool Thermostat

USER MANUAL WARNING! CONTENTS MODEL 1 SPECIFICATIONS READ ALL INSTRUCTIONS BEFORE PROCEEDING. Non-Programmable Single Stage Heat/Cool Thermostat Builder MODEL 1010 Series Non-Programmable Single Stage Heat/Cool Thermostat USER MANUAL Compatible with low voltage single stage gas, oil or electric heating or cooling systems, including single stage

More information

Programmable Room Thermostat 7 Day (5-2 Day) Models: 22083 / 22087 Power Supply: Battery / Mains

Programmable Room Thermostat 7 Day (5-2 Day) Models: 22083 / 22087 Power Supply: Battery / Mains Drayton Programmable Room Thermostat 7 Day (5-2 Day) Models: 22083 / 22087 Power Supply: Battery / Mains Invensys Controls Europe Technical Helpline: +44 (0) 845 130 7722 www.draytoncontrols.co.uk Installation

More information

Install Guide CT101. Caution. Caution

Install Guide CT101. Caution. Caution Install Guide CT101 PG 1 Caution top cover Your thermostat is a precise instrument, handle it with care. Turn off electricity to the system before installing or servicing thermostat or any part of the

More information

Cooling mode. Temperature adjustment button. Override button. 24 VAC COM AN1 COM OPEN CLOSED T2/AN2 T2/COM T3 T3 COM SENSOR COM C-Over COM NSB

Cooling mode. Temperature adjustment button. Override button. 24 VAC COM AN1 COM OPEN CLOSED T2/AN2 T2/COM T3 T3 COM SENSOR COM C-Over COM NSB TB6980/TB7980 1. Introduction The TB6980/TB7980 digital thermostats provide proportional plus integral individual space temperature control in zoned commercial HVAC systems such as hydronic and pressure

More information

Control4 Wireless Thermostat by Aprilaire. User Guide

Control4 Wireless Thermostat by Aprilaire. User Guide Control4 Wireless Thermostat by Aprilaire User Guide Control4 disclaimer Control4 makes no representations or warranties with respect to this publication, and specifically disclaims any express or implied

More information

Drayton Digistat +2RF/+3RF

Drayton Digistat +2RF/+3RF /+3RF Programmable Room Thermostat Wireless Model: RF700/22090 Model: RF701/22092 Power Supply: Battery - Thermostat Mains - Digistat SCR Invensys Controls Europe Customer Service Tel: 0845 130 5522 Customer

More information

Wireless Solutions. Application Selection Guide

Wireless Solutions. Application Selection Guide Wireless Solutions Application Selection Guide THERMOSTATS ZONING AIR CLEANERS HUMIDIFIERS DEHUMIDIFIERS UV SYSTEMS VENTILATION WATER SOLUTIONS COMBUSTION RedLINK Wireless Systems TrueZONE Panel Return

More information

T7350 Programmable Thermostat FOR CONVENTIONAL/HEAT PUMP SYSTEMS

T7350 Programmable Thermostat FOR CONVENTIONAL/HEAT PUMP SYSTEMS T7350 Programmable Thermostat FOR CONVENTIONAL/HEAT PUMP SYSTEMS Contents Features... 2 Settings... 3 Programming... 5 U.S. Registered Trademark Copyright 2003 Honeywell International Inc. All Rights Reserved

More information

MS7 Single Zone Mini Split System Air Conditioners and Heat Pumps

MS7 Single Zone Mini Split System Air Conditioners and Heat Pumps 2011 Lennox Industries Inc. Dallas, Texas, USA 506789 01 08/2011 MS7 Single Zone Mini Split System Air Conditioners and Heat Pumps This manual is the property of the homeowner and must be left with the

More information

AQUATROL Zone Synchronizing Programmable Relay Boiler Controls AQ25A

AQUATROL Zone Synchronizing Programmable Relay Boiler Controls AQ25A AQUATROL Zone Synchronizing Programmable Relay Boiler Controls AQ25A USER OPERATION AND MAINTENANCE WARNING Risk of electrical shock. Can cause severe injury, property damage or death. Only trained, experienced,

More information

ACONT900AC43UA Communicating, Programmable Comfort Control

ACONT900AC43UA Communicating, Programmable Comfort Control ACONT900AC43UA Communicating, Programmable Comfort Control OWNER S GUIDE Pub No. 69-1820-04 TABLE OF CONTENTS Page Contents 3 Features 4 Home Screen 6 Programming Your Heating and Cooling Schedule 14 Operating

More information

ComfortLink II Installation Guide. 3 Zone Panel (optional) 4 Zone Sensor with Display (optional) 5 Zone Sensor (optional) 6 Zone Dampers (optional)

ComfortLink II Installation Guide. 3 Zone Panel (optional) 4 Zone Sensor with Display (optional) 5 Zone Sensor (optional) 6 Zone Dampers (optional) 18-HD64D1-3 ComfortLink II Installation Guide Other Installation Guides may be necessary, based on system configuration. A complete list of other optional components is shown below. 1 Control 2 Relay Panel

More information

Installation Instructions

Installation Instructions TP --- PAC, TP --- PHP TP --- NAC, TP --- NHP Performance Series AC / HP Thermostat Installation Instructions A07049 Programmable Control A07048 Non-Programmable Control Designed and Assembled in the U.S.A.

More information

SMT-920 Viking. Modbus Addendum. Document version 1.1. Version 2.7 Viking firmware

SMT-920 Viking. Modbus Addendum. Document version 1.1. Version 2.7 Viking firmware SMT-920 Viking Modbus Addendum Document version 1.1 Version 2.7 Viking firmware Preface The SMT-920 Viking HVAC controller from Smart Temp Australia is a standalone commercial Air conditioning controller

More information

Owner s Guide. TrueIAQ. Digital IAQ Control 69-2072-05

Owner s Guide. TrueIAQ. Digital IAQ Control 69-2072-05 Owner s Guide TrueIAQ Digital IAQ Control 69-2072-05 69-2072_C.indd 1 7/31/2008 2:04:24 PM Table of contents User Information About TrueIAQ... 1 Operation... 2 Display screen reference... 3 Adjusting IAQ

More information

HP PS1810-24G Switch Quick Setup Guide, and Safety/Regulatory Information

HP PS1810-24G Switch Quick Setup Guide, and Safety/Regulatory Information HP PS80-4G Switch Quick Setup Guide, and Safety/Regulatory Information For more detailed instructions and information to set up your switch, view or download the Installation and Getting Started Guide

More information

Mark IV/AC Controller for Legacy Console Water Source Heat Pumps

Mark IV/AC Controller for Legacy Console Water Source Heat Pumps Operation & Maintenance Data OM 120-4 Group: WSHP Part Number: 910146916 Date: October 2013 Mark IV/AC Controller for Legacy Console Water Source Heat Pumps Specific to Mark IV Boards with Part No. 056792402

More information

TABLE 1: Wiring Terminals. Connect to... 1C 1H 2C 2H 1H1C 2H1C 2H2C 3H2C

TABLE 1: Wiring Terminals. Connect to... 1C 1H 2C 2H 1H1C 2H1C 2H2C 3H2C Installation TURN OFF POWER TO THE SYSTEM AT THE MAIN POWER PANEL TO AVOID ELECTRICAL SHOCK. Installation should be carried out by an electrician or a qualified technician. 1.1 Find a Location for the

More information

RC-100 / RC-100B Heat Pump 2 Stage Heat / 1 Stage Cool Thermostat Installation Instructions

RC-100 / RC-100B Heat Pump 2 Stage Heat / 1 Stage Cool Thermostat Installation Instructions RC-100 / RC-100B Heat Pump 2 Stage Heat / 1 Stage Cool Thermostat Installation Instructions DESCRIPTION The RC-100 is a precision digital thermostat designed for 24 VAC heat pump systems. It has the capability

More information

WHITE-RODGERS COMFORT-SET 90 SERIES

WHITE-RODGERS COMFORT-SET 90 SERIES INSTALLATI DESCRIPTI WHITE-RODGERS COMFORT-SET 90 SERIES MULTI-STAGE INSTALLATI/CFIGURATI This White-Rodgers Automatic Setback Digital Thermostat uses microcomputer technology to provide precise time and

More information

INSTALLATION AND MAINTENANCE

INSTALLATION AND MAINTENANCE INSTALLATION AND MAINTENANCE Specifications: is suitable for floor heating systems, Power Supply AC 120/ 240V,50/60Hz Maximum Load 15A, resistive Maximum Power 1800W at 120VAC; 3600W at 240VAC GFI Class

More information

Specifications are subject to change without notice according to Carrier Policy of continuous development.

Specifications are subject to change without notice according to Carrier Policy of continuous development. Specifications are subject to change without notice according to Carrier Policy of continuous development. 03501019 Rev. (0) -2009 Thank you for selecting Carrier Air Conditioner You can be justifiably

More information

± 3 % or better at 40 %RH and 23 ºC [73 ºF] 0.8 mm 2 [18 AWG] minimum. -10 ºC to 50 ºC [14 ºF to 122 ºF], 0-95 %RH

± 3 % or better at 40 %RH and 23 ºC [73 ºF] 0.8 mm 2 [18 AWG] minimum. -10 ºC to 50 ºC [14 ºF to 122 ºF], 0-95 %RH Room Humidistat Features: Attractive modern look with large LD and backlight Icons driven information and 1 line of text External humidity sensor input Humidification and dehumidification indicator Multi

More information

T7560A,B,C Digital Wall Module

T7560A,B,C Digital Wall Module T7560A,B,C Digital Wall Module HONEYWELL EXCEL 5000 OPEN SYSTEM BEFORE INSTALLATION All wiring must comply with local electrical codes and ordinances or as specified on installation wiring diagrams. Digital

More information

Portable Air Conditioner

Portable Air Conditioner Portable Air Conditioner Owner's Manual Model:3 in 1 12,000 Btu/h Series 3 Please read this owner s manual carefully before operation and retain it for future reference. CONTENTS 1. SUMMARY...1 2. PORTABLE

More information

1F82-0261 5/1/1 Day Programmable. 1F82-0261 Thermostat Thermostat Configuration Options Heat Pump. Maximum Stages Heat/Cool 2/1

1F82-0261 5/1/1 Day Programmable. 1F82-0261 Thermostat Thermostat Configuration Options Heat Pump. Maximum Stages Heat/Cool 2/1 Blue 2 Heat Pump Thermostat Heat Pump Installation and Operating Instructions Save these instructions for future use! FAILURE TO READ AND FOLLOW ALL INSTRUCTIONS CAREFULLY BEFORE INSTALLING OR OPERATING

More information

User Guide. Linksys PLEK500. Powerline Networking Adapter

User Guide. Linksys PLEK500. Powerline Networking Adapter User Guide Linksys PLEK500 Powerline Networking Adapter Contents Overview............... 3 Features..................... 3 How Powerline networking works........... 4 Example installation 4 Installing

More information

REMOTE CONTROL MANUAL

REMOTE CONTROL MANUAL REMOTE CONTROL MANUAL ENGLISH CONTENT PRECAUTIONS...1-2 ROOM IFEEL MODE TIMER TEMP USING THE REMOTE CONTROL UNIT...3 SLEEP SET CLEAR HOUR OPERATION...4-8 Thank you for purchasing our Room Air Conditioner.

More information

Carrier Thermostat Quick Reference Guide

Carrier Thermostat Quick Reference Guide Cool Share Web-Programmable Thermostat Residential Carrier Thermostat Quick Reference Guide Thank you for taking an active role in helping reduce the region s demand for electricity during the summer.

More information

User s Information Guide

User s Information Guide 32-5038-10 User s Information Guide Trane CleanEffects TM Whole House Air Filtration System Congratulations Your TRANE CleanEffects TM air filtration system is the most advanced, innovative and effective

More information

Workshop 7 PC Software - Tracker

Workshop 7 PC Software - Tracker Workshop 7 PC Software - Tracker Goal: You will startup and perform advanced setup functions using Tracker PC software. You will also setup equations to control MP503 binary outputs. The Binary Output

More information

VisionPRO 8000 Touchscreen Programmable Thermostat

VisionPRO 8000 Touchscreen Programmable Thermostat VisionPO 8000 Touchscreen Programmable Thermostat FEATUES PODUT DATA APPLIATION The VisionPO 8000 Touchscreen Programmable Thermostat is an effortless, 7-Day programmable thermostat that provides universal

More information

Portable Evaporative Air Cooler. OWNER S MANUAL Read and save these instructions before use. Model: CL48PM

Portable Evaporative Air Cooler. OWNER S MANUAL Read and save these instructions before use. Model: CL48PM Portable Evaporative Air Cooler OWNER S MANUAL Read and save these instructions before use Model: CL48PM Power rating: 130 Watts Voltage rating: 230 Volt, 50Hz Made in P.R.C. QUICK START GUIDE Fill with

More information

Installer s Guide. XB200 Comfort Control 18-HD29D1-3. TCONT200AN11AA 1 Heat (Gas, Oil* or Elec) / 1 Cool Electronic Non-Programmable, 4 Wire Hookup

Installer s Guide. XB200 Comfort Control 18-HD29D1-3. TCONT200AN11AA 1 Heat (Gas, Oil* or Elec) / 1 Cool Electronic Non-Programmable, 4 Wire Hookup Installer s uide XB200 Comfort Control TCONT200AN11AA 1 Heat (as, Oil* or Elec) / 1 Cool Electronic Non-Programmable, 4 ire Hookup ALL phases of this installation must comply with NATIONAL, STATE AND LOCAL

More information

User Guide ecobee3. 2014 ecobee 250 University Ave Suite 400 Toronto Ontario M5H 3E5 Canada Toll free 1.877.932.6233 www.ecobee.

User Guide ecobee3. 2014 ecobee 250 University Ave Suite 400 Toronto Ontario M5H 3E5 Canada Toll free 1.877.932.6233 www.ecobee. User Guide ecobee3 2014 ecobee 250 University Ave Suite 400 Toronto Ontario M5H 3E5 Canada Toll free 1.877.932.6233 www.ecobee.com e3-ug-r001 1 Table of Contents Overview... 4 Getting Help... 4 Touch Screen...

More information

RDJ10RF/SET. Wireless room temperature controller with 24-hour time switch and LCD. Programmable, for heating systems

RDJ10RF/SET. Wireless room temperature controller with 24-hour time switch and LCD. Programmable, for heating systems 3 072 RDJ10RF RCR10/433 Wireless room temperature controller with 24-hour time switch and LCD Programmable, for heating systems RDJ10RF/SET Operating modes: Automatic, Comfort, Energy Saving, and Frost

More information

Please read this owner s Manual carefully before operating the unit. - Cooling - Heating - Dehumidifying - Fan

Please read this owner s Manual carefully before operating the unit. - Cooling - Heating - Dehumidifying - Fan Please read this owner s Manual carefully before operating the unit. - Cooling - Heating - Dehumidifying - Fan TABLE OF CONTENTS INTRODUCTION 2 IMPORTANT SAFEGUARDS...2 PACKAGE CONTAINS..2 NAMES OF PARTS.3

More information

AE8-1328 R5 March 2011. Copeland Digital Compressor Controller AE8-1328 R5. Specifications

AE8-1328 R5 March 2011. Copeland Digital Compressor Controller AE8-1328 R5. Specifications AE8-1328 R5 March 2011 Copeland Digital Compressor Controller Introduction The Digital Compressor Controller is the electronics interface between the Copeland Scroll Digital compressor or the Copeland

More information

Quick Start Guide. Cisco SPA232D Mobility Enhanced ATA

Quick Start Guide. Cisco SPA232D Mobility Enhanced ATA Quick Start Guide Cisco SPA232D Mobility Enhanced ATA Package Contents Analog Telephone Adapter Ethernet Cable Phone Cable Power Adapter Quick Start Guide Product CD-ROM Welcome Thank you for choosing

More information

FAST-STAT. Model 7000 Installation Instructions. Application. Fossil Fuel / Supplemental Controller. Before Installing This Product

FAST-STAT. Model 7000 Installation Instructions. Application. Fossil Fuel / Supplemental Controller. Before Installing This Product FAST-STAT Model 7000 Installation Instructions Application The FAST-STAT Model 7000 is designed to reduce installation time when converting from an air conditioner to a single or 2- stage heat pump. Before

More information

Portable Evaporative Air Cooler. OWNER S MANUAL Read and save these instructions before use. Model: CL30XC

Portable Evaporative Air Cooler. OWNER S MANUAL Read and save these instructions before use. Model: CL30XC Portable Evaporative Air Cooler OWNER S MANUAL Read and save these instructions before use Model: CL30XC Power rating: 250 Watts Voltage rating: 230 Volt, 50Hz Made in P.R.C. QUICK START GUIDE Fill with

More information

Honeywell CT3500/CT3595 PROGRAMMABLE THERMOSTAT

Honeywell CT3500/CT3595 PROGRAMMABLE THERMOSTAT Honeywell CT3500/CT3595 PROGRAMMABLE THERMOSTAT Weekday, Saturday and Sunday Programmable Heat and/or Cool Low Voltage (20 to 30 Vac) Thermostat and Wallplate Model CT3500/CT3595 OWNER S GUIDE Para pedir

More information

SC 2201. Installation, Operation & Application Guide

SC 2201. Installation, Operation & Application Guide SC 2201 Manual Changeover Non-Programmable Hardwired Non-Programmable Electronic Thermostat For use with Heat Pumps Up to 2-Stage Heat, 2-Stage Cool 30-Minute Power Loss Memory etention For use with 24

More information

Intelligent Wireless GSM Alarm System

Intelligent Wireless GSM Alarm System Wireless GSM Alarm System Intelligent Wireless GSM Alarm System Profile For a better understanding of this product, please read this user manual thoroughly before using it. 2013.3.V1.0 Wireless GSM Alarm

More information