COMMERCIAL GAS AND ELECTRIC STACKED WASHER/ DRYER INSTALLATION INSTRUCTIONS

Size: px
Start display at page:

Download "COMMERCIAL GAS AND ELECTRIC STACKED WASHER/ DRYER INSTALLATION INSTRUCTIONS"

Transcription

1 COMMERCIAL GAS AND ELECTRIC STACKED WASHER/ DRYER INSTALLATION INSTRUCTIONS MODELS MLG19PD, MLE19PD The installation, including a proper exhaust system, is the responsibility of the owner. LEAVE THESE INSTRUCTIONS WITH THE OWNER Printed in U.S.A

2 CONTENTS: 1. Before you start 8. Gas connection 2. Space requirements 9. Water supply connection 3. Location 10. Drain hose connection 4. Unpacking 11. Commercial installation accessories 5. reversal 12. Final installation checklist 6. Dryer exhaust 13. Technical specification 7. Electrical connection 1. Before you start Items provided with your washer/dryer: Gas Washer/ Dryer Only Electric Washer/ Dryer Only Gas Adapter Typical tools needed for installation: PTFE tape Jointing compound Cutting knife Pipe wrench Adjustable spanners Spirit level Screwdrivers T20 security Torx screwdriver Duct tape (heat resistant) WARNINGS: Read these instructions carefully before you start, and make sure you have everything necessary for proper installation. These instructions cover both gas or electric dryer stacked on top of the electric washer. Proper installation is the responsibility of the owner. This appliance must be installed in accordance with these Maytag installation instructions, and all local and national regulations, such as for electrical wiring, municipal buildings, gas fitting. For Australia the installation should also be carried out in accordance with the AGA Installation Code for gas burning appliances. Maytag gas dryers have been certified for operation on either Natural Gas or LP Gas (with appropriate conversion). Service calls performed as a result of incorrect installation may be the responsibility of the installer. These instructions should be left with the owner for future reference. If disposing of an old dryer or washer, remove the door(s) to prevent it being a hazard to young children. Page 1

3 2. Space requirements The washer/dryer dimensions are shown in the figure below: Location of Canadian terminal block (gas models) 27 3 /16" 69 cm 5 1 /2" 5" 14 cm 12.7 cm Location of Canadian terminal block (electric models) 5/8" 1.6 cm 27 1 /2" 69.9 cm Dryer 3 1 /4" 8.3 cm Connection Gas Manifold 41" cm Location of dryer terminal block on electric models and power supply cord on gas models (except Canadian) 3/4" 1.9 cm 38 3 /16" 97 cm 13 1/2" 34.3 cm 71 1 /2" cm 1 1 /8" 2.9 cm 39 5 /32" 99.5 cm 3/8" min..95 cm Washer Exit location of washer drain hose 13 1 /2" 34.3 cm Location of washer water valve connections 27 1 /2" 69.9 cm 3. Location Each appliance should be located to permit adequate room in front for loading the clothes, and sufficient room behind for the dryer exhaust system and washer hose connections. The dryer is factory-ready for rear exhaust. To exhaust out the left side, use an accessory exhaust kit available from your dealer. Instructions are included with the kit. When installing the dryer, the following minimum clearances to combustibles apply; clearance to wall and sides 0 inches. Top 0 inches with outside exhaust; rear 0 inches with outside exhaust. It is important to make sure the room has an adequate air supply for gas combustion and/or drying operation. This is particularly important for multiple unit installations. The operation of the dryer may affect the operation of other gas appliances which take their air supply for safe combustion from the same room. If in doubt, consult the appliance manufacturers. An adequate means of ventilation must be provided that opens directly to outside air. For gas washer/dryer installations where dry cleaning machines are also installed, the sources of makeup air and air movement to the dryers must be located away from the dry cleaners. The appliance must not be installed or stored in an area where it will be exposed to outside weather, or where water may freeze, since the washer will always retain some water in the water valve, pump and hose areas. The area must be kept clear and free of combustible materials, flammable vapours or liquids. Operating temperature should be above 15 C (60 F). Page 2

4 IMPORTANT: This appliance is not IPX4 (splashproof) rated. It must not be installed or stored in an area where it will be exposed to water. Do not use a water hose or wet cloth to clean the outside of the appliance. For best performance, the appliance must be installed on a solidly constructed floor. Wood floors may need to be reinforced to minimize vibration and/or unbalanced washer load situations. Carpeting and soft tile surfaces are contributing factors in vibration and/or tendency for an appliance to move slightly during the washer spin cycle. Never install the appliance on a platform or weak supported structure. 4. Unpacking IMPORTANT: Notice that the washer hoses are tied up with a shipping strap. The upper straps on the back of the machine should not be cut or removed until the machine is ready to be installed. To remove appliance from transit base. Cut both lower shipping straps where they wrap around the crate bottom, DO NOT BE ALARMED as the tub will jump up when the last strap is cut. Lay two of the carton corner posts on the floor, and tip the appliance on its back to lay across the carton corner posts. Pull loose straps from the bottom of the washer. Release the transit base by removing the two wire hooks with a screwdriver as shown. Locate the metal buckles attached to the shipping straps at back of washer. Carefully cut away straps near both buckles, completely removing both buckles from the washer. Pull loose straps from back of washer one at a time until all straps have been removed. Loosen the leveling feet lock nuts. Place appliance in its intended location and adjust feet until the top is level on all four edges, before tightening lock nuts. A carpenter s level should be used on all four edges of top cover. 5. reversal swing direction can be successfully changed using the following procedure: Upper Dryer Dryer : 1. Remove the two screws in the hinges that secure the hinges to the front panel. Slightly lift the door and remove from the dryer front shroud. Set the door aside. 2. Remove the two hinge hold covers and the door catch cover and transfer them to the other side of the door opening. 3. Move the following parts to the opposite side of the door: 2 hinges and 4 screws, 4 colored door screws, door strike and screw, inner door cover plate and screw. 4. Reposition the door with the relocated hinges into the slots opposite of the original mounting position. Seat the hinges fully into the slots and screw the hinges into the front panel. Catch Hinge Screws Hinge Hole Cover Catch Cover Inner Cover Plate Strike Screws Page 3

5 Washer : 1. Swing door fully open and remove the two screws securing the hinges to the front panel. 2. Lift door slightly and pull door out of plastic front shroud. Press the plastic shroud toward the cabinet, should the hinge bind. Set the door aside. 3. Transfer the hinge hole covers to the opposite side of the door opening. 4. Transfer the hinges to the opposite side of the door, while transferring the colored screws to the previous hinge location. Position the hinge pin to the outside of the door panel. 5. Reposition the door into the plastic shroud and seat the hinges fully into the plastic shroud. Secure the hinges to the front panels with the hinge screws. 6. Close the door and run the washer through a wash cycle to check for leaks. If leaks occur, reposition the hinges to allow more contact between the lower edge of the door liner and the door boot. Hinge Hole Covers Hinges Screws Screws 6. Dryer exhaust The dryer must be exhausted to the outside air. This is necessary for gas combustion (on gas models), and will also prevent large amounts of moisture and some lint from being blown into the room. WARNING: Plastic or non-metal flexible duct presents a potential fire hazard. NEVER USE PLASTIC OR NON-METAL FLEXIBLE DUCT. If your existing ductwork is plastic, non-metal or combustible, replace it with metal. Plastic flexible duct can kink, sag, be punctured, reduce airflow, extend drying times and affect dryer operation. USE A MINIMUM OF 100mm (4 ) DIAMETER RIGID ALUMINUM OR RIGID GALVANIZED STEEL DUCT. Do not use smaller duct. Ducts larger than 100mm can result in increased lint build-up. Any lint build-up should be cleaned regularly. If flexible metal must be used in some areas, use the type with a stiff sheet metal wall. Do not use flexible duct with a thin foil wall. Serious blockage can result if flexible metal duct is bent too sharply. Never install any type of flexible duct in walls, ceiling or other concealed spaces. Keep exhaust duct as straight and short as possible. Exhaust systems longer than recommended can extend drying times, affect dryer operation and may collect lint. Secure joints with proper duct tape. Do not use screws. DO NOT EXHAUST DRYER INTO ANY WALL, CEILING, CRAWL SPACE OR OTHER CONCEALED SPACE IN A BUILDING, GAS VENT OR CHIMNEY. THIS COULD CREATE A FIRE HAZARD FROM LINT EXPELLED BY THE DRYER. Page 4 Number of 90 Turns Exhaust Hood Type 100mm 64mm Maximum length of 100mm (4 ) diameter rigid metal duct m 24 m 20 m 15 m 11 m 18 m 15 m 12 m 9 m 7 m Maximum length of 100mm (4 ) diameter flexible stiff walled metal duct m 10 m 9 m 8 m 7 m 9 m 7 m 6 m 5 m 4 m

6 The exhaust duct should end with an exhaust hood with a swing-out flap to prevent back-draughts and access for wildlife (see Accessories). Never use an exhaust hood with a magnetic flap. The hood should have at least 300mm (12 ) clearance between the bottom of the hood and the ground or other obstruction. The hood opening should point down. Never install a screen over the exhaust outlet. When possible, do not exhaust the dryer directly into a basement window well in order to avoid a lint build-up. Do not exhaust under a building. If exhaust ductwork must run through an unheated area, the duct should be insulated and slope slightly down towards the exhaust hood to reduce condensation and lint build-up. If an existing exhaust system is to be used with your new machine, you must ensure: The exhaust system meets all local and national regulations That plastic flexible duct is not used. To completely inspect and clean all lint accumulation from the duct interior. The duct is not kinked or crushed which could restrict airflow. The exhaust hood flap opens and closes freely. If multiple units are exhausted into a common duct: 1. An exhaust cross-section area of 78cm 2 ( ) is required per dryer. This will allow for free air movement should all dryers be operated simultaneously. 2. A power exhaust may be used on multiple installations. 3. Ducts larger than 100mm (4 ) diameter can result in increased lint accumulation. Such lint accumulation should be cleaned regularly. 4. Exhaust ducting should be kept as short and direct as possible. The operating pressure in the exhaust system must not exceed 23mm (0.92 ) water gauge, or be less than 0. This can be measured with the dryer(s) operating, by inserting a manometer connection at the point where the exhaust duct connects to the dryer (a no-heat part of a cycle should be used, without clothes load and with a clean lint filter). Inspect and clean the interior of the dryer exhaust system at least twice a year. Disconnect from the electricity supply prior to cleaning. Check the gas supply connection any time the machine is moved. Frequently check to be sure the exhaust hood flap opens and closes freely. 7. Electrical connection WARNING: This is a 3-wire appliance which must be earthed. The gas dryer/washer is fitted with an electrical supply cord and plug. It should be connected to an electricity supply socket at the voltage shown on the dataplate. The minimum supply fuse capacity should be 10A. The appliance must be positioned so that the plug is accessible. If the fitted plug is not used, the electrical connection must be carried out by a competent electrician in accordance with local or national wiring regulations. Do not use extension lead assemblies on commercial installations. If the supply cord is damaged, it must be replaced with a specially terminated cord by an authorized service agent or a similarly qualified person in order to avoid a hazard. The electric dryer/washer is supplied without an electric cord and plug. It must be connected to a singlephase electricity supply at the voltage shown on the dataplate, by a suitable fixed wiring installation in accordance with local and national wiring regulations. A 3-wire circular cord of minimum conductor size 2.5mm 2 cross-section area should be used. A 30A supply fuse should be used, and a switch with a minimum contact separation of 3mm in both poles must be incorporated into the fixed wiring for machine disconnection. A cord clamp bush is provided with the machine, and should be tightened on completion of wiring. The electrical mains terminals are located behind the small rear access panel at the top of the dryer, and connections should be made as shown in the figure above. Remember to replace the terminal access panel. Page 5

7 NOTE: In accordance with the European EMC Directive (89/336/EEC) the maximum electricity supply system impedance to which the electric dryer/washer should be connected is declared to be Ω + J0.155 Ω. Some local wiring regulations require connection of an additional earth bond connection to the appliance. An earthing kit (Part No ) is available. It contains the earth wire, clamp, earth screw and washer. The wire should be connected to the earth (ground) terminal on the rear panel of the dryer using the additional screw and washer shown at right. 8. Gas connection WARNING: The gas dryer is factory-set with a burner orifice for Natural Gas supply (see Technical Specification). It may be converted for use with LP (butane or propane) gas using the correct conversion kit (see Accessories). Full instructions are supplied with the kit. Before installation, check that the local distribution conditions, nature of gas and pressure, and the adjustment of the appliance are compatible. Gas installation must be carried out in accordance with any local or national gas installation regulations by a suitably qualified person. Each dryer gas inlet connection is 3/8 NPT thread. An adapter is included for conversion to ISO.7-1 thread. A 12.5mm (1/2 ) gas supply line is recommended for each dryer. For multiple unit installations the size of the main gas line must be adequate for the number of dryers (see Technical Specification for gas flow rate per dryer). Gas connection to the dryer must be made by means of a flexible gas hose suitable for the appliance and gas category (a fixed gas pipe could be damaged should the machine vibrate). A means of restraint should be used on the appliance to prevent straining of the gas supply when the appliance is moved. Remove the gas inlet connection thread protective cap. Apply jointing compound or approximately 1-1/2 turns of PTFE sealing tape over all threaded connections, and securely tighten (Note: jointing compound used must be resistant to LPG). Check for leaks as directed by local or national regulations. DO NOT use a naked flame to check for gas leaks. A pressure measurement tapping is provided on the gas valve within each dryer, accessible after removal of the front service access panel (disconnect from electricity supply before removing this panel). NOTE: All gas dryers should be disconnected from gas supply before any over-pressure testing of the gas supply system. The gas dryer uses an automatic ignition system to ignite the burner. There is no constant burning pilot light. 9. Water supply connection EARTH BOND SCREW (GROUND) Cold water supply: Pressure: MPa ( p.s.i.) Temperature: 25 C max. (77 F max.) Hot water supply: Pressure: MPa ( p.s.i.) Temperature: 49 C 60 C (120 F 140 F) These water pressures are required to correctly fill the washer in the proper time. Pressures of less than 0.2 MPa may cause a malfunction in the machine water valve, and it may also not shut off completely. Fit water supply stop-taps to allow easy disconnection of fill hoses. Always turn taps off when washer is not in use (make sure they are accessible). Page 6

8 Connect inlet hoses to water supplies using screen washer at tap connections. NOTE: Accessory inlet hoses are available tin various lengths up to 3m (10 ). Ensure the correct hose end is used on each hose. The appliance end has an NPT thread. The water supply end has a standard European 3/4 BSP thread. Do not overtighten hose connections. Hand tight should be adequate to avoid leaks without damaging the sealing washer. 10. Drain hose connection Install gooseneck end of drain hose into a standpipe. Be sure an air-tight connection is NOT made between the drain hose and the standpipe. Recommended height of the standpipe is 0.9m (36 ). If the standpipe is less than 0.6m (24 ) high, the drain hose should be routed through the clip to raise the hose to the proper height. Standpipe must be large enough to accept the outside diameter of the drain hose. If a floor drain is used, route the drain hose through the drain hose clip before routing to the drain. Without the 0.6m (24 ) high elevation, water may run out of the washer prematurely. NOTE: Caution must always be exercised to avoid kinking the drain hose. For best performance the drain hose should not be restricted in any way, through elbows, couplings or excessive lengths. HOSE RETAINER CLIP To prevent accidental dislodging secure the drain hose to the standpipe, inlet hose or laundry tub with the tie strap provided in the parts package. 11. Commercial installation accessories For all accessories and replacement parts, contact your Maytag Commercial Distributor. Vent hood 100mm (4 ) opening Aluminum duct pipe 100mm x 610mm (4 x 24 ) Aluminum elbow, 100mm (4 ) Aluminum window plate 381mm x 508mm (15 x 20 ) with 100mm (4 ) hole Flexible aluminum duct 100mm (4 ) 812mm (38 ) extending to 2.44m (8 ) Clamp for flexible aluminum duct Exhaust duct kit for base or left side exhausting Rectangular vent kit Anchor bracket kit Gas conversion kit NATURAL to LPG Gas conversion kit LPG to NATURAL Earthing kit Page 7

9 12. Final installation checklist Instructions and Installation Kit have been removed from inside. Shipping straps have been removed. Appliance has been properly levelled. All legs should be firmly on the floor and lock nuts MUST be tightened. Water is turned on and checked for leaks at tap and water valve connections. Appliance is connected to electricity supply and is properly earthed. Drain hose is properly located into drain facility and is not kinked. All exhaust and gas connections to dryer are correctly made. Turn on gas supply (where applicable). Turn on water supplies. Switch on electricity supply. Following Operating Instructions, check the operation of the dryer first, then the washer. Dryer On gas dryers the burner may not ignite initially due to air in the gas pipework. Allowing the dryer to operate on a heat setting will purge the pipework. If the gas does not ignite within 5 minutes, turn the dryer off and wait for 5 more minutes. Make sure gas supply has been turned on. In order to confirm gas ignition and correct operation of the burner (mostly blue flame) the professional installation engineer may remove the front access panel to view the burner. WARNING: Do not touch any electrical parts and replace panel immediately after this check. To confirm gas ignition at any other time, the exhaust duct should be checked for heat. Washer Ensure washer fills properly on all temperature selections. Test for proper operation by running the washer through a complete cycle. Page 8

10 13.TECHNICAL SPECIFICATION (see dataplate by door opening for full model details) Gas model: V ~ 50 Hz 1ph 1200W max. IP22 Clothes capacity: 9 kg max. Gas Category: II 2H3+ Gross heat input: 6.5 kw (gas consumption 23.6 MJ/h) Net heat input: 5.9kW Factory settings: Natural gas: (G20) Gas rate: 0.62 m 3 /h (23.6 MJ/h) Injector size: 2.16mm Supply pressure, normal: 20 mb (2 KPa) Test point pressure: 8.7 mb (0.87 KPa) Supply pressure, min.: 11.3 mb (1.13 KPa) Test point pressure: 8.7 mb (0.87 KPa) With LPG conversion kit (Europe): LP gas: butane (G30) Gas rate: 0.19 m 3 /h (23.6 MJ/h) Injector size: 1.25mm Supply pressure, normal: 29 mb (2.9 KPa) Test point pressure: Not applicable LP gas: propane (G31) Gas rate: m 3 /h (23.6 MJ/h) Injector size: 1.25mm Supply pressure, normal: 37 mb (3.7 KPa) Test point pressure: Not applicable With LPG conversion kit (Australia): LP gas: propane (G31) Gas rate: m 3 /h (23.6 MJ/h) Injector size: 1.35mm Supply pressure, normal: 27.5 mb (2.75 KPa) Test point pressure: Not applicable Countries of destination: UK, IE, IT, ES, AU Cold water supply: Pressure: MPa ( p.s.i.) Temperature: 25 C max. (77 F max.) Hot water supply: Pressure: MPa ( p.s.i.) Temperature: 49 C 60 C (120 F 140 F) Electric dryer/ washer: V~ 50 Hz: 1ph 5450W max. IP22 Clothes capacity: Dryer: 9 kg max. Washer: 8.1 kg Manufacturer: MAYTAG APPLIANCES: 1 Dependability Square, Newton, Iowa 50208, U.S.A. Page 9

BUILT-IN DISHWASHER INSTALLATION INSTRUCTIONS

BUILT-IN DISHWASHER INSTALLATION INSTRUCTIONS BUILT-IN DISHWASHER INSTALLATION INSTRUCTIONS PLEASE READ COMPLETE INSTRUCTIONS BEFORE YOU BEGIN LEAVE INSTALLATION INSTRUCTIONS AND USER'S GUIDE WITH OWNER ALL ELECTRIC WIRING AND PLUMBING MUST BE DONE

More information

Installation Instructions

Installation Instructions Installation Instructions Built-In Dishwasher If you have questions, call 1-800-4-MY-HOME (1-800-469-4663) or visit our website at: www.sears.com BEFORE YOU BEGIN Read these instructions completely and

More information

UB1 AIR CONDITIONING UNIT INSTALLATION INSTRUCTIONS

UB1 AIR CONDITIONING UNIT INSTALLATION INSTRUCTIONS UB1 AIR CONDITIONING UNIT INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS: Carefully read these instructions before installing your new air-conditioner. AUSTRALIAN AUTOMOTIVE AIR AL00500054E 1 Table

More information

Your safety and the safety of others are very important.

Your safety and the safety of others are very important. NATURAL GAS TO PROPANE CONVERSION KIT 090 INSTALLATION INSTRUCTIONS FOR ALTITUDES 0 -,00 FT. ONLY PROPANE CONVERSION KIT SAFETY... INSTALLATION REQUIREMENTS... Tools and Parts... LP Gas Requirements...

More information

INFRARED QUARTZ WALL HEATER

INFRARED QUARTZ WALL HEATER INFRARED QUARTZ WALL HEATER MODEL NO: IQ2000 PART NO: 6939004 MOUNTING & OPERATION INSTRUCTIONS GC0715 INTRODUCTION Thank you for purchasing this CLARKE Infrared Wall Heater. Before attempting to use this

More information

San josé OWNER S MANUAL

San josé OWNER S MANUAL San josé OWNER S MANUAL Assembling & operating manual San josé 30 mbar - PORTABLE GAS BARBECUE 1. 2. 3. Improper installation, adjustment, alteration, service or maintenance can injury or property damage.

More information

Installation Instructions

Installation Instructions Instructions for Dryers Original Instructions Keep These Instructions for Future Reference. (If this machine changes ownership, this manual must accompany machine.) www.speedqueen.com Part No. 5206R8 November

More information

Electrical Connection. Provide Proper Electrical Supply. Electrical Requirements. Connecting using the supplied cord and plug

Electrical Connection. Provide Proper Electrical Supply. Electrical Requirements. Connecting using the supplied cord and plug Electrical Connection When installed the range must be electrically grounded in accordance with local codes or; in the absence of local codes with the National Electrical Code ANSI/NFPA 70, latest edition.

More information

Installation Instructions

Installation Instructions GE Consumer & Industrial Appliances Installation Instructions Junction Box Cover Within this user bag, you will find a junction box cover and a #10 hex head screw used to attach the junction box cover

More information

36G22, 36G23, 36G24 & 36G52 36J22, 36J23, 36J24 & 36J52 DSI and HSI Single Stage Combination Gas Valve

36G22, 36G23, 36G24 & 36G52 36J22, 36J23, 36J24 & 36J52 DSI and HSI Single Stage Combination Gas Valve Operator: Save these instructions for future use! FAILURE TO READ AND FOLLOW ALL INSTRUCTIONS CAREFULLY BEFORE INSTALLING OR OPERATING THIS CONTROL COULD CAUSE PERSONAL INJURY AND/OR PROPERTY DAMAGE. DESCRIPTION

More information

DRYER VENTING SPECIFICATIONS DRYER SAFETY

DRYER VENTING SPECIFICATIONS DRYER SAFETY DRYER VENTING SPECIFICATIONS Table of Contents DRYER SAFETY...1 INSTALLATION REQUIREMENTS...4 Venting Requirements...5 DRYER INSPECTION AND CLEANING...7 Frequency of Exhaust System Cleaning...7 Inspecting

More information

CARING FOR YOUR WATER HEATER

CARING FOR YOUR WATER HEATER http://waterheatertimer.org/troubleshoot-rheem-tankless-water-heater.html Water Heater Inspections CARING FOR YOUR WATER HEATER Venting System (Direct Vent Only) The venting system should be inspected

More information

Electric Dryer Installation Instructions

Electric Dryer Installation Instructions Electric Dryer Installation Instructions Table of Contents DRYER SAFETY... 2 INSTALLATION REQUIREMENTS... 3 Tools and Parts... 3 Location Requirements... 4 Electrical Requirements... 6 Install Leveling

More information

Andersen Electric Window Opener for Andersen Awning and Roof Windows

Andersen Electric Window Opener for Andersen Awning and Roof Windows W A Electric Window Opener Electric Window Opener for Awning and Roof Windows Congratulations! You have just purchased one of the many fine products. For ease of installation and continued enjoyment of

More information

- 2 - IMPORTANT SAFETY REMINDERS

- 2 - IMPORTANT SAFETY REMINDERS USER MANUAL IMPORTANT SAFETY REMINDERS This appliance should only be used for domestic cleaning, as described in this user guide. Please ensure that this guide is fully understood before operating the

More information

USER INSTRUCTIONS FOR 10 LITRE PORTABLE DEHUMIDIFIER MODEL NO. DHMD102

USER INSTRUCTIONS FOR 10 LITRE PORTABLE DEHUMIDIFIER MODEL NO. DHMD102 USER INSTRUCTIONS FOR 10 LITRE PORTABLE DEHUMIDIFIER MODEL NO. DHMD102 THANK YOU FOR CHOOSING YOUR NEW DEHUMIDIFIER. BEFORE USING THE UNIT READ THESE INSTRUCTIONS FULLY AND RETAIN THEM FOR FUTURE REFERENCE

More information

OWNER S MANUAL Table Tennis Table Patent Pending

OWNER S MANUAL Table Tennis Table Patent Pending OWNER S MANUAL Table Tennis Table Patent Pending Be sure to write your model number and serial number here for future reference. You can find these numbers printed on the bottom of the table. MODEL # T8179

More information

Portable Air Conditioner

Portable Air Conditioner Portable Air Conditioner Owner's Manual Model:3 in 1 12,000 Btu/h Series 3 Please read this owner s manual carefully before operation and retain it for future reference. CONTENTS 1. SUMMARY...1 2. PORTABLE

More information

PRODUCT: WASHER / WASHER-DRYER COMBO MODEL: AW 120 / AW 122 / AW 125 AWD 120 / AWD 121 / AWD 129

PRODUCT: WASHER / WASHER-DRYER COMBO MODEL: AW 120 / AW 122 / AW 125 AWD 120 / AWD 121 / AWD 129 PRODUCT: WASHER / WASHER-DRYER COMBO MODEL: The information included in this Splendide Repair Manual may change without notice. Please see our web site www.splendide.com/service/docs.html for updates,

More information

COMMERCIAL GAS DRYER

COMMERCIAL GAS DRYER COMMERCIAL GAS DRYER MODELS CGD8990XW0 4 12 Litho In U.S.A. (CMS) (psw) c 2012 WHIRLPOOL CORPORATION Part No. Rev. B TOP AND CONSOLE PARTS 2 TOP AND CONSOLE PARTS 1 Literature Parts W10184516 Installation

More information

User Guide. Bagless Cylinder White. Get Cleaning... vax.co.uk. Vax Careline: (UK) 0844 412 8455 (ROI) 1-800 928 308. White series

User Guide. Bagless Cylinder White. Get Cleaning... vax.co.uk. Vax Careline: (UK) 0844 412 8455 (ROI) 1-800 928 308. White series C88-VW-B UG [Update 10.05.12]_User guide 10/05/2012 09:40 Page 1 User Guide Vax Careline: (UK) 0844 412 8455 Bagless Cylinder White Get Cleaning... What s your Vax model number? (Located on the top flap

More information

Split-type Air-Conditioner INSTALLATION MANUAL CONTENTS FOR INSTALLER MXZ-3A30NA MXZ-4A36NA ATTENTION. English. Français. Español

Split-type Air-Conditioner INSTALLATION MANUAL CONTENTS FOR INSTALLER MXZ-3A30NA MXZ-4A36NA ATTENTION. English. Français. Español Split-type Air-Conditioner MXZ-3A30NA MXZ-4A36NA INSTALLATION MANUAL Refer to the installation manual of each indoor unit for indoor unit installation. English Français Español ATTENTION This manual mentions

More information

2-SLICE COOL TOUCH TOASTER

2-SLICE COOL TOUCH TOASTER 2-SLICE COOL TOUCH TOASTER PLA0405 Instruction Manual Due to on-going product improvements, specifications and accessories may change without notice. Actual product may differ slightly to that depicted.

More information

COMMERCIAL GAS DRYER

COMMERCIAL GAS DRYER COMMERCIAL GAS DRYER MODELS CGM2751TQ0 (WHITE) CGM2751TQ1 (WHITE) 5 12 Litho in U.S.A. (CMS) (psw) c 2012 WHIRLPOOL CORPORATION Part No. W10119631 Rev. C TOP AND CONSOLE PARTS W10119631 2 TOP AND CONSOLE

More information

Installation Guide. 5 Series 15 W. Undercounter/Freestanding Nugget Ice Machine

Installation Guide. 5 Series 15 W. Undercounter/Freestanding Nugget Ice Machine Installation Guide 5 Series 15 W. Undercounter/Freestanding Nugget Ice Machine Table of Contents Warnings & Important Safety Instructions 3 Dimensions (Professional) 5 Dimensions (Custom Panel) 6 Specifications

More information

IMPORTANT SAFETY INSTRUCTIONS WARNING READ AND SAVE THESE OPERATING AND SAFETY INSTRUCTIONS BEFORE USING THIS HEATER.

IMPORTANT SAFETY INSTRUCTIONS WARNING READ AND SAVE THESE OPERATING AND SAFETY INSTRUCTIONS BEFORE USING THIS HEATER. THERMAWAVE CERAMIC HEATER Model HZ-850 Series Model HZ-860 Series IMPORTANT SAFETY INSTRUCTIONS WARNING READ AND SAVE THESE OPERATING AND SAFETY INSTRUCTIONS BEFORE USING THIS HEATER. Warning Failure to

More information

Cooktop Low-Profile Ventilation Hoods

Cooktop Low-Profile Ventilation Hoods INSTALLATION GUIDE Cooktop Low-Profile Ventilation Hoods Contents Wolf Cooktop Low-Profile Ventilation Hoods........ 3 Cooktop Low-Profile Hood Specifications.......... 4 Cooktop Low-Profile Hood Installation............

More information

OWNER S MANUAL DRAINVAC ATOMIK PRINTED APRIL 4-2011

OWNER S MANUAL DRAINVAC ATOMIK PRINTED APRIL 4-2011 OWNER S MANUAL th DRAINVAC ATOMIK PRINTED APRIL 4-2011 INTRODUCTION We take this opportunity to express our gratitude and extend our congratulations for your decision to purchase a Drainvac product. A

More information

IMPORTANT INSTRUCTIONS & OPERATING MANUAL. Houston 50 Inch Electric Wall Mounted Fireplace Black / White

IMPORTANT INSTRUCTIONS & OPERATING MANUAL. Houston 50 Inch Electric Wall Mounted Fireplace Black / White IMPORTANT INSTRUCTIONS & OPERATING MANUAL Houston 50 Inch Electric Wall Mounted Fireplace Black / White Model Number:MFE5050BK Model Number:MFE5050WH Read these instructions carefully before attempting

More information

SHOT BLAST CABINET MODEL NO: CSB20B

SHOT BLAST CABINET MODEL NO: CSB20B SHOT BLAST CABINET MODEL NO: CSB20B PART NO: 7640110 USER INSTRUCTIONS GC0216 INTRODUCTION Thank you for purchasing this CLARKE Shot Blast Cabinet which is designed for professional workshop use. Before

More information

G26 Corp. 9721-L11 Revised 07-2001 LENNOXOEMPARTS.COM. Service Literature G26 SERIES UNITS

G26 Corp. 9721-L11 Revised 07-2001 LENNOXOEMPARTS.COM. Service Literature G26 SERIES UNITS Service Literature G26 SERIES UNITS G26 series units are high-efficiency upflow gas furnaces manufactured with DuralokPlust aluminized steel clamshell-type heat exchangers. G26 units are available in heating

More information

orlando OWNER S MANUAL

orlando OWNER S MANUAL orlando OWNER S MANUAL 2 Assembling & operating manual Orlando 30 mbar - PORTABLE GAS BARBECUE 1. 2. 3. Improper installation, adjustment, alteration, service or maintenance can injury or property damage.

More information

LPM-06 CONVERSION KIT

LPM-06 CONVERSION KIT LPM-06 CONVERSION KIT TWO-STAGE FURNACE NATURAL GAS TO L.P. GAS CONVERSION Goodman Manufacturing Company, L.P. 2009-2011 5151 San Felipe, Suite 500, Houston, TX 77056 www.goodmanmfg.com -or- www.amana-hac.com

More information

NAVIEN AMERICA INC. 17855 FITCH AVENUE

NAVIEN AMERICA INC. 17855 FITCH AVENUE Navien America Inc. Specification Details for the Navien models: CC-240 CC-240A For Potable Water Heating and Space Heating NAVIEN AMERICA INC. 17855 FITCH AVENUE IRVINE, CALIFORNIA, USA 92614 Toll Free:

More information

INSTALLATION & OPERATING INSTRUCTIONS

INSTALLATION & OPERATING INSTRUCTIONS INSTALLATION & OPERATING INSTRUCTIONS WARNING RISK OF ELECTRIC SHOCK. CONNECT ONLY TO A CIRCUIT PROTECTED BY A GROUND-FAULT CIRCUIT-INTERRUPTER. THE UNIT SHOULD BE INSTALLED BY A QUALIFIED SERVICE REPRESENTATIVE.

More information

Installation Instructions For Slider Casement Air Conditioners

Installation Instructions For Slider Casement Air Conditioners Installation Instructions For Slider Casement Air Conditioners NOTE: These instructions describe installation in a typical wood framed window with a wood SLIDE-BY sash, or installation in a metal CASEMENT

More information

SMD Rework Station TABLE OF CONTENTS

SMD Rework Station TABLE OF CONTENTS SMD Rework Station Thank you for purchasing the Hakko 50B SMD Rework Station. The Hakko 50B is designed to solder and desolder surface mounted devices with hot air. Please read this manual before operating

More information

Please also see 10 golden rules for correct Saniflo installation on www.saniflo.co.uk

Please also see 10 golden rules for correct Saniflo installation on www.saniflo.co.uk 1. Description Sanicom is a lifting pump for wastewater used in commercial applications (restaurants, hairdressing salons, the catering industry etc.). The unit operates automatically, has a high performance

More information

COMMERCIAL TOP LOAD WASHER INSTALLATION, USER & SET-UP INSTRUCTIONS

COMMERCIAL TOP LOAD WASHER INSTALLATION, USER & SET-UP INSTRUCTIONS COMMERCIAL TOP LOAD WASHER INSTALLATION, USER & SET-UP INSTRUCTIONS MODELS: MAT12CS, MAT12PD, MAT13MN, MAT13PN LEAVE THESE INSTRUCTIONS WITH THE OWNER MAYTAG COMPANY, NEWTON, IOWA 50208 2207647 IMPORTANT

More information

GENUINE PARTS INSTALLATION INSTRUCTIONS

GENUINE PARTS INSTALLATION INSTRUCTIONS GENUINE PARTS INSTALLATION INSTRUCTIONS DESCRIPTION: Illuminated Kick Plate APPLICATION: Rogue (2011) PART NUMBER: 999G6 GX010 KIT CONTENTS: Item A B C G H QTY 1 1 1 D 1 E 1 F 3 15 6 Description Kick Plate,

More information

Please keep this manual for f uture reference.

Please keep this manual for f uture reference. GAS WATER/AGUA Congratulations! You've just purchased a new Marey Portable tankless water heater and will soon begin to enjoy the benefits of going tankless. Take the time to thoroughly read and understand

More information

INSTRUCTION MANUAL REFRIGERATOR BEFORE USE, PLEASE READ AND FOLLOW ALL SAFETY RULES AND OPERATING INSTRUCTIONS.

INSTRUCTION MANUAL REFRIGERATOR BEFORE USE, PLEASE READ AND FOLLOW ALL SAFETY RULES AND OPERATING INSTRUCTIONS. INSTRUCTION MANUAL Model Number: BC-130 REFRIGERATOR BEFORE USE, PLEASE READ AND FOLLOW ALL SAFETY RULES AND OPERATING INSTRUCTIONS. 1 REFRIGERATOR SAFETY Your safety and the safety of others are very

More information

SELECTION, APPLICATION AND MAINTENANCE

SELECTION, APPLICATION AND MAINTENANCE DIESEL PROTECTION SYSTEMS Automatic Diesel Engine Shut Down System for Safe Area Applications SELECTION, APPLICATION AND MAINTENANCE Series 300 Series 310 SYSTEM DESCRIPTION Suitable for attended engine

More information

5800 Temperature Sensor Cable Assembly

5800 Temperature Sensor Cable Assembly 5800 Temperature Sensor Cable Assembly Removal and Replacement Instruction Sheet #60-4702-070 Revision D, January 14, 2013 Overview The 5800 has two refrigeration temperature sensors, one attached to the

More information

Reverse Cycle Inverter Split System Air Conditioner

Reverse Cycle Inverter Split System Air Conditioner Reverse Cycle Inverter Split System Air Conditioner Model Number TAC-09CHSA/JAI5 INSTALLATION MANUAL Contents 03 Warranty Details 04 Welcome 05 General Safety Instructions 06 Product Overview 07 Selecting

More information

POSEIDON 2-29, 2-25 & 2-22 POSEIDON 2-29, 2-25 & 2-22 XT

POSEIDON 2-29, 2-25 & 2-22 POSEIDON 2-29, 2-25 & 2-22 XT POSEION 2-29, 2-25 & 2-22 POSEION 2-29, 2-25 & 2-22 XT Repair Manual Index A. Safety precautions 3 B. Technical data 4 C. Structure 5-6. Service / Repair 7-23 E. Tools 24 F. Function 25-26 G. Electric

More information

PARTS NEEDED FOR CONVERTING FROM LP TO NG

PARTS NEEDED FOR CONVERTING FROM LP TO NG 1 6 7 8 3 5 4 10 9 2 PARTS NEEDED FOR CONVERTING FROM LP TO NG Number Description 1 30" NG Manifold 2 NG side burner valve 3 NG Regulator 4 Rear I/R NG orifice 4 Rear I/R NG orifice 5 Side burner NG orifice

More information

Replacement parts. WM97+ gas-fired water boiler Boiler Manual. OBTAIN PARTS ONLY THROUGH WEIL-McLAIN THE BOILER CONTAINS CERAMIC FIBER MATERIALS

Replacement parts. WM97+ gas-fired water boiler Boiler Manual. OBTAIN PARTS ONLY THROUGH WEIL-McLAIN THE BOILER CONTAINS CERAMIC FIBER MATERIALS Replacement parts DO NOT SERVICE THE BOILER WITHOUT A WM97+ MAINTENANCE KIT AVAILABLE Failure to adhere to these guidelines can result in severe personal injury, death or substantial property damage. The

More information

Table of Contents. www.hunterfan.com. What to Expect with. Preparation. Tools Needed. Wiring. Hanging the Fan. Blades. Motor Housing.

Table of Contents. www.hunterfan.com. What to Expect with. Preparation. Tools Needed. Wiring. Hanging the Fan. Blades. Motor Housing. www.hunterfan.com Table of Contents What to Expect with Your Installation 30 inches Hanging the Fan Wiring 8 Maintenance, Operation & Cleaning Light Kit 13??? 14 1 9 Troubleshooting 11 5 Blades Motor Housing

More information

Convection Ovens. BX Classic. Models BX4 / FG 189C, BX4-6040 / FG 158C, BX10 / FG 180C. Operator's Manual

Convection Ovens. BX Classic. Models BX4 / FG 189C, BX4-6040 / FG 158C, BX10 / FG 180C. Operator's Manual Convection Ovens BX Classic Models BX4 / FG 189C, BX4-6040 / FG 158C, BX10 / FG 180C Operator's Manual Belshaw Bros., Inc. 814 44 th Street NW, Suite 103 Auburn, WA 98001 USA Phone: 206-322-5474 Fax: 206-322-5425

More information

Fully Automatic Washing Machine User manual

Fully Automatic Washing Machine User manual Fully Automatic Washing Machine User manual This manual is for HWMP55-918 Please read this manual carefully before using. Retain it for future reference. CONTENTS CONTENTS Inside cover Parts 1 Safety precautions

More information

SHOWER WATER HEATER MODEL BS 35 / 45 / 60 BS 35 E / 45 E / 60 E OPERATION AND INSTALLATION INSTRUCTIONS

SHOWER WATER HEATER MODEL BS 35 / 45 / 60 BS 35 E / 45 E / 60 E OPERATION AND INSTALLATION INSTRUCTIONS SHOWER WATER HEATER MODEL BS 35 / 45 / 60 BS 35 E / 45 E / 60 E OPERATION AND INSTALLATION INSTRUCTIONS 2 This water heater must be installed (water and electrical installation), commissioned and serviced

More information

3 IN 1 BATHROOM HEATER

3 IN 1 BATHROOM HEATER 3 IN 1 BATHROOM HEATER MODEL NO.: A515 - SH MINI FUNCTION: HEATER, EXHAUST FAN AND LIGHT Dear customers, Thank you for selecting the AUPU 3 in 1 Bathroom Heater. Please read all instructions before commencing

More information

Ceiling Fan Installation Instructions

Ceiling Fan Installation Instructions Ceiling Fan Installation Instructions 1525..series OWNER S MANUAL READ AND SAVE THESE INSTRUCTIONS Total fan wieght with light kit 1-1525-CUL-English INSTALLATION CH-545 Safety Tips WARNING: TO REDUCE

More information

M7RL Series TECHNICAL SPECIFICATIONS. FEATURES and BENEFITS. High Efficiency / Direct Vent Condensing Downflow Gas Furnace

M7RL Series TECHNICAL SPECIFICATIONS. FEATURES and BENEFITS. High Efficiency / Direct Vent Condensing Downflow Gas Furnace TECHNICAL SPECIFICATIONS M7RL Series High Efficiency / Direct Vent Condensing Downflow Gas Furnace Induced Draft - 9%+ AFUE Input 4,000 thru 7,000 Btuh The high efficiency downflow gas furnace is especially

More information

Getting the best from your urn

Getting the best from your urn 444448538 Standard 444448539 Deluxe Getting the best from your urn Remove any plastic film from the urn before use. Any water in the urn is due to testing and is normal. The urn must be used on a flat

More information

NOTE: Additional user information for your printer may be available in the "Manuals" section at support.dell.com.

NOTE: Additional user information for your printer may be available in the Manuals section at support.dell.com. CAUTION: General Safety Instructions Use the following safety guidelines to help ensure your own personal safety and to help protect your equipment and working environment from potential damage. NOTE:

More information

STEADYfast Stabilizer Installation Notes Fifth Wheel and Travel Trailers 11/23/13

STEADYfast Stabilizer Installation Notes Fifth Wheel and Travel Trailers 11/23/13 STEADYfast Stabilizer Installation Notes Fifth Wheel and Travel Trailers 11/23/13 (See Supplemental Instructions for trailers with heavy duty round footplates and/or Power Leveling Systems) PHONE SUPPORT

More information

INSTALL INSTRUCTIONS KK-C-HVAC-1 HVAC UNIT 2003-2014 CHEVROLET/GMC VANS FOR

INSTALL INSTRUCTIONS KK-C-HVAC-1 HVAC UNIT 2003-2014 CHEVROLET/GMC VANS FOR INSTALL INSTRUCTIONS KK-C-HVAC-1 HVAC UNIT 2003-2014 CHEVROLET/GMC VANS FOR (For NEW 2007 ALL WHITE KWIK-KITS ONLY) Warning do not attempt to install A/C units unless you are experienced with servicing

More information

Installation Manual. Solar Pool Heating System. Read the complete manual before beginning the installation

Installation Manual. Solar Pool Heating System. Read the complete manual before beginning the installation Solar Pool Heating System Installation Manual Read the complete manual before beginning the installation 1. Sizing the System Visit www.techno-solis.com to size the system using the sizing calculator.

More information

Navico-Northstar 2kW JRC Radar Package, Scanner Cable Removal and Replacement

Navico-Northstar 2kW JRC Radar Package, Scanner Cable Removal and Replacement Navico-Northstar 2kW JRC Radar Package, Scanner Cable Removal and Replacement This work instruction describes the methods and means for which to remove and reinstall optional scanner cable configurations

More information

DBF 4XL Dryer Booster Fans

DBF 4XL Dryer Booster Fans Installation and Operation Manual Item #: 401315 Rev Date: 121514 DBF 4XL Dryer Booster Fans DBF4XL Kit Includes: Dryer Booster Fan, 1 pc Fan Mounting Bracket and Hardware, 1 pc Wall Label (Mount on wasll

More information

Carpet Washer. vax.co.uk VRS5W. Vax Careline: (UK) 0844 412 8455 (ROI) 1-800 928 308. Vax model number: Version 1.0

Carpet Washer. vax.co.uk VRS5W. Vax Careline: (UK) 0844 412 8455 (ROI) 1-800 928 308. Vax model number: Version 1.0 VRS5W Powermax User Guide V1.0.qxd:V1.0 23/7/10 15:35 Page 1 Vax Careline: (UK) 0844 412 8455 (ROI) 1-800 928 308 Carpet Washer Vax model number: VRS5W instruction manual Version 1.0 Please read carefully

More information

RE-3 : SOLID TOP RANGE RANGE TOP ONLY

RE-3 : SOLID TOP RANGE RANGE TOP ONLY VULCAN ELECTRIC SOlid top oven range MODEL: RE-3 - SOLID TOP oven Range RE-3T - SOLID range top only ON CABINET BASE RE-3 : SOLID TOP RANGE Model Re-3T : Solid TOP RANGE TOP ONLY Index: General Data 2

More information

UHIR Series. Horizontal or Vertical Mounting Industrial / Commercial Electric Unit Heater. Owner s Manual

UHIR Series. Horizontal or Vertical Mounting Industrial / Commercial Electric Unit Heater. Owner s Manual UHIR Series Horizontal or Vertical Mounting Industrial / Commercial Electric Unit Heater Owner s Manual This manual covers installation, maintenance and repair parts. Read carefully before attempting to

More information

DETACHABLE WINDSHIELD AND DOCKING HARDWARE KIT

DETACHABLE WINDSHIELD AND DOCKING HARDWARE KIT -J00 REV. 00-- DETACHABLE WINDSHIELD AND DOCKING HARDWARE KIT GENERAL Kit Number -A, 0-, -, 0-, -, - 0, -0 Models These kits fit and later FXST, FXSTB, FXSTC, and and later FXDWG Harley-Davidson model

More information

with installation dynafact boost GAUGE this manual is for use with systems 64050-64054

with installation dynafact boost GAUGE this manual is for use with systems 64050-64054 owners manual with installation instructions dynafact boost GAUGE this manual is for use with systems 64050-64054 GENERAL INSTALLATION PRACTICES This manual is an installation guide for all 1. Banks DynaFact

More information

USER S, MAINTENANCE and SERVICE INFORMATION MANUAL

USER S, MAINTENANCE and SERVICE INFORMATION MANUAL CONTENTS SAFETY INFORMATION................ 2 FOR YOUR SAFETY....................... 2 SYSTEM OPERATION.................. 2 THERMOSTATS........................... 2 INTERMITTENT IGNITION DEVICE...........

More information

INSTALLATION MANUAL ELECTRIC RANGE. Please read these instructions thoroughly before installing and operating the range.

INSTALLATION MANUAL ELECTRIC RANGE. Please read these instructions thoroughly before installing and operating the range. ENGLISH ESPAÑOL INSTALLATION MANUAL ELECTRIC RANGE Please read these instructions thoroughly before installing and operating the range. LRE3025ST LRE3085ST LRE3083ST LRE3083SB LRE3083SW LRE3021ST LDE3037ST

More information

ATS Overhead Table Shelf System INSTRUCTION MANUAL

ATS Overhead Table Shelf System INSTRUCTION MANUAL ATS Overhead Table Shelf System INSTRUCTION MANUAL ATS Overhead Table Shelf System Instruction Manual Warranty Newport Corporation warrants this product to be free of defects in material and workmanship

More information

LUCCI AIRFUSION QUEST II CEILING FAN

LUCCI AIRFUSION QUEST II CEILING FAN LUCCI AIRFUSION QUEST II CEILING FAN WITH IR REMOTE INSTALLATION OPERATION MAINTENANCE WARRANTY INFORMATION CAUTION READ INSTRUCTIONS CAREFULLY FOR SAFE INSTALLATION AND FAN OPERATION. V1.0 QUEST II IR

More information

NewAir AC-10000E, AC-10000H Portable Air Conditioner Owner s Manual PLEASE READ AND SAVE THESE INSTRUCTIONS

NewAir AC-10000E, AC-10000H Portable Air Conditioner Owner s Manual PLEASE READ AND SAVE THESE INSTRUCTIONS NewAir AC-10000E, AC-10000H Portable Air Conditioner Owner s Manual PLEASE READ AND SAVE THESE INSTRUCTIONS BEFORE USE GENERAL SAFETY INSTRUCTIONS: ALWAYS OPERATE THE UNIT IN AN UPRIGHT POSITION AND PLACE

More information

Installation Instructions

Installation Instructions GE Consumer & Industrial Appliances Installation Instructions Junction Box Cover Within this user bag, you will find a junction box cover and a #10 hex head screw used to attach the junction box cover

More information

Instruction Manual. Alfa Laval SB Membrane Sample Valve ESE02963-EN1 2015-10. www.sks-online.com www.sks-webshop.com.

Instruction Manual. Alfa Laval SB Membrane Sample Valve ESE02963-EN1 2015-10. www.sks-online.com www.sks-webshop.com. Instruction Manual Alfa Laval SB Membrane Sample Valve ESE02963-EN1 2015-10 Original manual Table of contents The information herein is correct at the time of issue but may be subject to change without

More information

Dehumidifier Users manual. For Models: DH45S DH65S

Dehumidifier Users manual. For Models: DH45S DH65S Dehumidifier Users manual For Models: DH45S DH65S 950-0062-revD Jan. 9 2007 FORWARD The appearance of the units that you purchase might be slightly different from the ones described in the Manual, but

More information

DC REFRIGERATORS 12/24 VOLTS INSTALLATION AND OWNER S MANUAL

DC REFRIGERATORS 12/24 VOLTS INSTALLATION AND OWNER S MANUAL DC REFRIGERATORS 12/24 VOLTS INSTALLATION AND OWNER S MANUAL Service Information If service or parts are required, contact the nearest Norcold Service Center. To find an authorized Norcold Service Center

More information

CEILING CASSETTE FAN COIL UNIT

CEILING CASSETTE FAN COIL UNIT CEILING CASSETTE FAN COIL UNIT Operation and Installation Manual MHCFC4W-04, 08, 12, 16 Four way ceiling cassette fan coil unit Please read this manual before using the fan coil unit. Installation and

More information

Not required for most applications Not required for most applications High pressure (12-803 provided) High pressure (12-803 provided)

Not required for most applications Not required for most applications High pressure (12-803 provided) High pressure (12-803 provided) ELECTRIC FUEL PUMPS P/N 12-801-1, 712-801-1, 12-802-1, 712-802-1, 12-815-1, & 712-815-1 FUEL PRESSURE REGULATORS P/N 12-803, 12-501, 12-804, 12-500, & 15812NOS Installation Instructions THESE INSTRUCTIONS

More information

INSTALLATION AND SERVICE MANUAL

INSTALLATION AND SERVICE MANUAL CI8100 IMI Wilshire, Inc. IMI WILSHIRE, INC. COUNTER INTELLIGENCE BEVERAGE SYSTEM CI8100 INSTALLATION AND SERVICE MANUAL 1993 IMI Wilshire, Inc. TABLE OF CONTENTS CI8100 IMI Wilshire, Inc. SECTION I CI8100

More information

M-9424-463V Intake Manifold INSTALLATION INSTRUCTIONS

M-9424-463V Intake Manifold INSTALLATION INSTRUCTIONS Please visit www.fordracingparts.com for the most current instruction information!!! PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. AT ANY TIME YOU DO NOT UNDERSTAND THE

More information

SBC90. Abrasive Blast Cabinet Assembly & Operating Instructions

SBC90. Abrasive Blast Cabinet Assembly & Operating Instructions SBC90 Abrasive Blast Cabinet Assembly & Operating Instructions READ ALL INSTRUCTIONS AND WARNINGS BEFORE USING THIS PRODUCT. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE. This manual provides important

More information

MODEL J SERIES CONVERTER

MODEL J SERIES CONVERTER 3030 S Susan Street, MODEL J SERIES CONVERTER REPAIR KIT INSTRUCTIONS Important: Any maintenance, service or repair should be performed by trained and experienced service technicians. Proper tools and

More information

FRONT BUMPER INSTALLATION INSTRUCTIONS 2007-2011 DODGE / MERCEDES SPRINTER

FRONT BUMPER INSTALLATION INSTRUCTIONS 2007-2011 DODGE / MERCEDES SPRINTER Aluminess Products Inc 9402 Wheatlands Ct. #A Santee, CA 92071 619-449-9930 FRONT BUMPER INSTALLATION INSTRUCTIONS 2007-2011 DODGE / MERCEDES SPRINTER Please read before beginning Stainless steel hardware

More information

Safety, Operation and Maintenance Manual with Parts List

Safety, Operation and Maintenance Manual with Parts List Safety, Operation and Maintenance Manual with Parts List 20-Gallon Wet/Dry Vac Important Information and Safety Instructions PLEASE READ BEFORE USE! # 961130020 9/10-Rev 1 20-Gallon Wet/Dray Vac TABLE

More information

CORNER FRIDGE REFRIGERATION UNIT INSTALLATION AND OPERATION INSTRUCTIONS

CORNER FRIDGE REFRIGERATION UNIT INSTALLATION AND OPERATION INSTRUCTIONS CORNER FRIDGE REFRIGERATION UNIT INSTALLATION AND OPERATION INSTRUCTIONS D E F Y I N G C O N V E N T I O N Congratulations on your new Corner Fridge Your new corner fridge may have different functions

More information

42U/45U 28" Wide Rack Installation & Service Guide

42U/45U 28 Wide Rack Installation & Service Guide 42U/45U 28" Wide Rack Installation & Service Guide 96-00171-005 Rev B Important Information Information in this document is subject to change without notice and does not represent a commitment on the part

More information

Commercial Gas Furnace Upflow

Commercial Gas Furnace Upflow Commercial Gas Furnace Upflow Model G24-200 80% A.F.U.E. 200,000 Btuh Input Heating Cap. 7.5 or 10 Tons Nominal Add-On Cooling GUK FEATURES Certified by A.G.A./C.G.A. Laboratories. Heavy gauge painted

More information

MODEL 300505 INSTALLATION INSTRUCTIONS

MODEL 300505 INSTALLATION INSTRUCTIONS WWW.BURCAM.COM 2190 Boul. Dagenais West TEL: 514.337.4415 LAVAL (QUEBEC) FAX: 514.337.4029 CANADA H7L 5X9 info@burcam.com Your pump has been carefully packaged at the factory to prevent damage during shipping.

More information

Before installation it is important to know what parts you have and what the capabilities of these parts are.

Before installation it is important to know what parts you have and what the capabilities of these parts are. INSTALLATION GUIDE Before installation it is important to know what parts you have and what the capabilities of these parts are. The Recon XZT is the smallest and most powerful gauge of its kind. With

More information

Select Radiators Installation Guide

Select Radiators Installation Guide Select Radiators Installation Guide Table of Contents Informational Symbols...3 Before You Begin...4 Select Rough-In... 5 Connection Installation...6 Optional Piping Arrangements...7 Conventional Wall

More information

Guidelines for Earthquake Bracing of Residential Water Heaters

Guidelines for Earthquake Bracing of Residential Water Heaters Guidelines for Earthquake Bracing of Residential Water Heaters Department of General Services Division of the State Architect 1102 Q Street, Suite 5100 Sacramento, CA 95814 Phone: (916) 324-7099 Fax: (916)

More information

PLEASE READ ALL INSTRUCTIONS BEFORE USE AND SAVE A COPY FOR FUTURE REFERENCE!

PLEASE READ ALL INSTRUCTIONS BEFORE USE AND SAVE A COPY FOR FUTURE REFERENCE! PLEASE READ ALL INSTRUCTIONS BEFORE USE AND SAVE A COPY FOR FUTURE REFERENCE! 1. Read all instructions carefully before using the machine. 2. Do not touch hot surfaces. Use handles or knobs. The lid and

More information

VOYAGER 570G. 744A Sprayer Control

VOYAGER 570G. 744A Sprayer Control VOYAGER 570G 744A Sprayer Control U S E R M A N U A L U S E R M A N U A L Table of Contents CHAPTER 1 - INTRODUCTION...1 SYSTEM CONFIGURATIONS...1 KIT CONTENTS...3 CONTROL HOUSING ASSEMBLY...5 CHAPTER

More information

Guidelines for Earthquake Bracing Residential Water Heaters

Guidelines for Earthquake Bracing Residential Water Heaters Guidelines for Earthquake Bracing Residential Water Heaters Department of General Services Division of the State Architect In accordance with the Health and Safety Code Section 19215, the Division of the

More information

SIBIR MANUAL V110 KE. English page 5 RKE - 1D 822 70 66-02

SIBIR MANUAL V110 KE. English page 5 RKE - 1D 822 70 66-02 SIBIR MANUAL RKE - 1D V110 KE English page 5 822 70 66-02 2 1 A. Flue tube E. Adapter I. Thermostat B. Flue baffle F. Burner base J. Lever arm C. Control knob G. Lamp glass D. Fuel gauge H. Lamp glass

More information

VACUUM CLEANER INSTRUCTION MANUAL

VACUUM CLEANER INSTRUCTION MANUAL VACUUM CLEANER INSTRUCTION MANUAL MODEL: SVC9702 PLEASE READ THIS MANUAL CAREFULLY BEFORE USING AND KEEP IT PROPERLY FOR FUTURE USE 1 Safety Cautions: WARNING: To reduce the risk of fire, electrical shock,

More information

Instantaneous gas water heater

Instantaneous gas water heater Instantaneous gas water heater Models W 125...T1 installation operation maintenance The Bosch instantaneous water heater is a high efficiency, space saving answer to your water heating needs. All Bosch

More information

USER INSTRUCTIONS FOR GET PORTABLE 12k BTU AIR CONDITIONER MODEL No. GPACU12HR

USER INSTRUCTIONS FOR GET PORTABLE 12k BTU AIR CONDITIONER MODEL No. GPACU12HR USER INSTRUCTIONS FOR GET PORTABLE 12k BTU AIR CONDITIONER MODEL No. GPACU12HR CONTENTS Introduction Safety Notes Identification of parts Installation instructions Operation instructions Maintenance Troubleshooting

More information

Installation and Operating Instructions Installation Instructions for SS EPE-316L Series

Installation and Operating Instructions Installation Instructions for SS EPE-316L Series INSTR3010 0406 Installation and Operating Instructions Installation Instructions for SS EPE-316L Series Congratulations on your purchase of this Aqua-Pure high flow, single housing filtration system. This

More information

DTM04 TANK MONITOR DTM08 TANK MONITOR Dtm12 TANK MONITOR. Installation and Operation Manual

DTM04 TANK MONITOR DTM08 TANK MONITOR Dtm12 TANK MONITOR. Installation and Operation Manual DTM04 TANK MONITOR DTM08 TANK MONITOR Dtm12 TANK MONITOR Installation and Operation Manual 1 ENGLISH Safety Instructions 2 Features 2-3 Specifications 3 Installation 4-5 Wiring Diagrams 6-7 Warranty 8

More information