Technical. Configuration Notes. MITEL SIP CoE. Configure the Mitel 5000 Communications Platform SIP Trunking for use with EarthLink SIP trunk
|
|
- Janel Welch
- 7 years ago
- Views:
Transcription
1 MITEL SIP CoE Technical Configuration Notes Configure the Mitel 5000 Communications Platform SIP Trunking for use with EarthLink SIP trunk SIP CoE
2 NOTICE The information contained in this document is believed to be accurate in all respects but is not warranted by Mitel Networks Corporation (MITEL ). The information is subject to change without notice and should not be construed in any way as a commitment by Mitel or any of its affiliates or subsidiaries. Mitel and its affiliates and subsidiaries assume no responsibility for any errors or omissions in this document. Revisions of this document or new editions of it may be issued to incorporate such changes. No part of this document can be reproduced or transmitted in any form or by any means - electronic or mechanical - for any purpose without written permission from Mitel Networks Corporation. TRADEMARKS Mitel is a trademark of Mitel Networks Corporation. Windows and Microsoft are trademarks of Microsoft Corporation. Other product names mentioned in this document may be trademarks of their respective companies and are hereby acknowledged. Mitel Technical Configuration Notes Configure the Mitel 5000 Communications Platform for use with EarthLink SIP trunk August 2011, , Trademark of Mitel Networks Corporation Copyright 2011, Mitel Networks Corporation All rights reserved ii
3 Table of Contents OVERVIEW... 1 Interop History... 1 Interop Status... 1 Software & Hardware Setup... 1 Tested Features... 2 Device Limitations and Known Issues... 3 Network Topology... 4 CONFIGURATION NOTES... 5 Mitel 5000 Communications Platform Configuration Notes... 5 Network Requirements... 5 Assumptions for the Mitel 5000 Communications Platform Programming... 5 Licensing and Option Selection SIP Licensing... 6 Creating and Configuring a SIP Peer Trunk Group... 7 Programming the Configuration settings... 8 Programming the Trunk Group Configuration properties Programming the Trunks in Trunk Group Configuration Folder Phone Configurations Call Configurations Adtran 908e Configuration settings (Optional) iii
4
5 Overview This document provides a reference to Mitel Authorized Solutions providers for configuring the Mitel 5000CP to connect to EarthLink SIP trunk. The different devices can be configured in various configurations depending on your VoIP solution. This document covers a basic setup with required option setup. Interop History Version Date Reason 1 August 30, 2011 Initial Interop with Mitel 5000CP 5.0 and EarthLink SIP trunk Interop Status The Interop of EarthLink has been given a Certification status. This service provider or trunking device will be included in the SIP CoE Reference Guide. The status EarthLink achieved is: The most common certification, which means that SIP Trunk from EarthLink has been tested and/or validated by the Mitel SIP CoE team. Product support will provide all necessary support related to the interop, but issues unique or specific to the 3rd party will be referred to the 3rd party as appropriate. Software & Hardware Setup This was the test setup to generate a basic SIP call between EarthLink service provider and the 5000CP. Manufacturer Variant Software Version Mitel 5000CP CS 5.0 release 30 Mitel IP set 5340, Mitel MAS (NuPoint) Adtran Total Access 908e, IP Business Gateway A E Metaswitch Application Server Ver. 7.3 Nortel PSTN gateway CS2000/MG15K Acme Packet Session Boarder Controller SBC 4250 & 4500 Ver. SC6.1.0 MR-7 Patch 4 (Build 855) 1
6 Tested Features This is an overview of the features tested during the Interop test cycle and not a detailed view of the test cases. Please see the SIP Trunk Side Interoperability Test Plans ( ) for detailed test cases. This is an overview of the features tested during the Interop test cycle and not a detailed view of the test cases. Feature Feature Description Issues Basic Call Automatic Call Distribution MAS/NuPoint Voic Embedded voic Dynamic Extension Express Video Fax Making and receiving a call through the SIP Service provider and their PSTN gateway, call holding, transferring, conferencing, busy calls, long calls durations, variable codec. Making calls to an ACD environment with RAD treatments, Interflow and Overflow call scenarios and DTMF detection. Terminating calls to a NuPoint voic boxes and DTMF detection. Using the embedded voic system on Mitel 5000 Receiving a call through the SIP Service provider and their PSTN gateway to Mobile extensions and TUI interface. Also moving calls to/from Desktop and Twinned devices. Making and receiving a call through EarthLink SIP trunk with video capable devices. G.711 Fax Calls Not Supported Fax T.38 Fax Calls Not Supported - No issues found - Issues found, cannot recommend to use - Issues found
7 Device Limitations and Known Issues This is a list of problems or not supported features when EarthLink has a SIP trunk connected to the Mitel 5000 Communications Platform. Faxing Features Calls to busy PSTN numbers Video Calls Reliable Provisional Responses (PRACK) Packetization rate Call privacy on outbound calls Problem Description G.711 faxing is possible over the trunk only. Recommendation: None. EarthLink does not support T.38 faxing. When Mitel extension calls to a busy PSTN number, the audible busy tone is heard almost immediately. However, SIP message 486 Busy Here arrives at 5000CP only after 30 seconds. Because of this, forward trunk clearing is impossible until the real SIP message 486 is received. Recommendation: none. Contact EarthLink for further details. Mitel 5000CP does not support multiple m-lines and as such is incapable to process video calls. Video functionality is unavailable over the ErthLink SIP trunk. Recommendation: none Mitel 5000 Communications Platform does not support PRACK at this time. Recommendation: Contact Mitel for further information regarding this feature. The SIP trunk fully supports only 20ms packets rate whereas Mitel 5000CP supports 20ms and 30ms rates (Audio Frames). Recommendation: In Mitel 5000CP, keep packets rate of 20ms. There is no way to configure a "classical" privacy in 5000CP (with "anonymous"). If you remove the Calling Party Number from Trunk Group Configuration, EarthLink rejects this call. If you enter e.g. " ", then this call will be accepted and number delivered at far end is " ". Recommendation: Contact EarthLink for further information regarding this issue. 3
8 Network Topology This diagram shows how the testing network is configured for reference. Figure 1 Network Topology
9 Configuration Notes This section is a description of how the SIP Interop was configured. Disclaimer: Although Mitel has attempted to setup the interop testing facility as closely as possible to a customer premise environment, implementation setup could be different onsite. YOU MUST EXERCISE YOUR OWN DUE DILIGENCE IN REVIEWING, planning, implementing, and testing a customer configuration. Mitel 5000 Communications Platform Configuration Notes The following steps show how to program Mitel 5000 Communications Platform to interconnect with EarthLink Service Provider. Network Requirements There must be adequate bandwidth to support the voice over IP. As a guide, the Ethernet bandwidth is approx 85 Kb/s per G.711 voice session and 29 Kb/s per G.729 voice session (assumes 20ms packetization). As an example, for 20 simultaneous SIP sessions, the Ethernet bandwidth consumption will be approx 1.7 Mb/s for G.711 and 0.6Mb/s for G.729. Almost all Enterprise LAN networks can support this level of traffic without any special engineering. Please refer to the 5200 Engineering guidelines for further information. For high quality voice, the network connectivity must support a voice-quality grade of service (packet loss <1%, jitter < 30ms, one-way delay < 80ms). Assumptions for the Mitel 5000 Communications Platform Programming The SIP signaling connection was configured to use UDP on Port
10 Licensing and Option Selection SIP Licensing Ensure that the Mitel 5000 is equipped with enough SIP Trunks licences for the connection to EarthLink. This can be verified within the Software License form. Check the total number of licenses in the SIP Trunk Licences field. This is the maximum number of SIP trunk sessions that can be configured in the Mitel 5000 to be used with all service providers and applications. Figure 2: Example of SIP Licensing
11 Creating and Configuring a SIP Peer Trunk Group To support SIP trunks through a SIP trunk service provider, the SIP Trunk Groups folder was added to the SIP Peers folder in DB Programming. To create a SIP Trunk Group for EarthLink, navigate to System->Device and Feature Codes- >SIP Peers->SIP Trunk Groups and right click in the right hand window panel. Then select Create SIP Trunk Group. (See Figure 3) Figure 3: Example of Create SIP Trunk Group When you create a SIP Peer trunk group without using a template, you must obtain the necessary information from the SIP trunk service provider, and then configure this information in DB Programming. When Trunk group for EarthLink is been created, we have to configure parameters in Configuration and Trunk Group Configuration nodes. 7
12 Programming the Configuration settings Registrar: Although EarthLink SIP trunk requires registration, we don t need to configure any registration details in Mitel Instead, all these settings were configured in Adtran IP Business Gateway by EarthLink personnel. Set Enable Registration option to No as shown in Figure 4. Figure 4: Example of Registrar form
13 Authentication: In this form, we still need to configure Username and Password for outbound calls as shown in Figure 5. EarthLink should provide Username and Password. Figure 5: Example of Authentication form Keep-Alive: The Keep-Alive option keeps refreshing the NAT bindings for any Firewall/NAT in the path. It also helps in determining whether the SIP peer is reachable or not. Leave the default values here. NAT Settings: Specifies the NAT address type. The default is No NAT or SIP-Aware NAT (for systems that are using a SIP-aware firewall). If you are not using a SIP-aware firewall, you must change the setting to Non SIP-Aware NAT. Leave the default values here. Alternate IP/FQDN List: At the time of testing, EarthLink used a single IP address to send SIP messages to the Mitel Therefore, there is no need to configure any alternative IP addresses or FQDNs. Click Configuration node (see Figure 6) IP Address: Indicates the IP address of the SIP peer trunk group. Since we use Adtran IP Business Gateway as Back2Back agent, we have to configure IP address of Adtran s LAN interface here. Port Number: Indicates the port that the system listens on the system for SIP peer messages. The range is Leave the default value of
14 Fully Qualified Domain Name: Indicates the domain name of the SIP peer trunk group. In our test environment, we do not use FQDN. Therefore, leave is blank. Figure 6: Example of Configuration form Call Configuration: Enter the call configuration number in Value field that you want to use with this trunk group. Clicking Call Configuration takes you to the Call Configuration folder where you can add a new call configuration profile or configure the existing profile(s) (e.g. codecs for voice and faxing, DTMF settings, etc. See section Call Configurations). (System->IP-Related Information->Call Configurations-><call configuration number>). Operating State: Indicates the operating state of the SIP peer. If required, the status could be changed to Out-of-Service Maintenance. Maximum Number of Calls: Indicates the maximum number of concurrent calls that are been permitted towards the SIP peer. This number is not configurable in here and depends on number of trunks added at System->Device and Feature Codes->SIP Peers- >SIP Trunk Groups-><SIP Trunk group #>->Trunk Group Configuration->Trunks (see next section for details) Use ITU-T E.164 Phone Number: If set to Yes, the Mitel 5000 handles ITU-T E.164 formatted phone numbers as part of the incoming SIP INVITE messages from the SIP peer. Static Binding: It specifies whether a static binding exist for the corresponding SIP Peer. If set to Yes, then IP address and listening port for the SIP Peer must be configured. Leave this setting to Yes.
15 Use Peer Address In From Header: In our test environment, we set it to No. Programming the Trunk Group Configuration properties To program the Trunk Group Configuration properties, navigate to System->Device and Feature Codes->SIP Peers->SIP Trunk Groups-><SIP Trunk group #>->Trunk Group Configuration: As per Figure 7, we need to configure three most important parameters: - Day and Night Ring-In Type in our test environment we configured Single ring-in type with the value of 1310, where 1310 is the extension number where the incoming DID trunk calls are terminated. - Calling Party Number is the default calling party number, which 5000CP presents to the provider s SIP trunk. EarthLink should give this number to you. If this value is missing, EarthLink rejects to process this call. So, insure that this field is not blank. For the rest of the settings, refer to the DB Programming Help for trunk programming Figure 7: Example of Trunk Group Configuration 11
16 Programming the Trunks in Trunk Group Configuration Folder The number of SIP trunks that we create in here will appear as Maximum Number of Calls in the Configuration screen (see Figure 6). Create the SIP peer trunks as follows: Navigate to System->Device and Feature Codes->SIP Peers->SIP Trunk Groups-><SIP Trunk group #>->Trunk Group Configuration->Trunks Right-click the right pane and the select Create SIP Peer Trunk. The Create SIP Peer Trunk dialog box appears (see Figure 8). Select the extension number you want to use for the item in the Starting Extension field. The recommended range is ; Indicate the number of extensions you want to create in the Number of Extensions field. If the system is set to have more than one extension, the new trunks will be assigned sequentially to the next available numbers. Click OK. For the EarthLink, 3 extensions were created, See Figure 8. The number of available SIP Trunks licenses restricts the number of SIP peer trunks. Figure 8: Example of SIP Trunks creation
17 Phone Configurations Some configuration settings need to be updating for the extensions. In our test environment, when Outgoing key is pressed on the phone, we wanted to direct outbound calls to the EarthLink SIP trunk. To do this: Navigate to System->Device and Feature Codes->Phones-><Phone s extension number>->associated Extension In right hand pane, select Outgoing Extension and enter the number of SIP Trunk Group corresponding to EarthLink trunk (in our test environment 92006). See Figure 9 for details. You can configure a voic extension in the same screen. Figure 9: Configure outgoing extension for the phone When configuring call forwarding to a voic box, it is not enough to create the mailbox and assign it to the phone. You also have to define a Forwarding Path and assign it to the phone. To do this: Navigate to System->Phone Related Information->System Forwarding Paths Define at least Forwarding Point 1 for the selected path. In the example in Figure 10, we defined extension 2502 as the forwarding point for path #3. Extension 2502 is a MAS (NuPoint) server s voic pilot number. We also defined extension 2500 as Forwarding Point 1 for path #2. Extension 2500 represents the pilot number for Basic voic (BVM). 13
18 NOTE: For easier identification later on, we would recommend to enter a text in the Description field as shown in Figure 10. Figure 10: Example of Forwarding Path definition Now, when Forwarding Path #3 and #6 are defined, we can assign one of them to the phone: Navigate to System->Device and Feature Codes->Phones-><Phone s extension number>->forwarding Paths Right click in right hand pane and select Add to Forwarding Paths List Select the Forwarding Paths and click Next Select the required Forwarding Path s number and click Add Items button Click Finish NOTE: If you wish to forward unanswered internal calls to the defined Forwarding Point, set parameter Fwd Call Type IC Calls to Yes as shown on Figure 11.
19 Figure 11: Example of the properties for defined Forwarding Path 15
20 Call Configurations Call configurations define the settings that IP phones and gateways use when connected to calls. You can assign multiple devices to a specific call configuration. By default, all IP devices are been placed in Call Configuration 1, which is programmable. You do not need to add SIP phones to Call Configurations, because these devices negotiate call configurations before establishing a connection. You can program up to 25 different Call Configurations. Since EarthLink SIP trunk does not support T.38 faxing, we recommend enabling codec G.711U for faxing (see Figure 12 for details). Set Audio Frames/IP Packet to 2 which corresponds to the packet rate of 20ms. To view the list of IP phones which are currently assigned to the call configuration: Navigate to System->IP-Related Information->Call Configurations-><call configuration number> Click Phones
21 Figure 12: Call Configuration Options You can move extensions to this call configuration profile. To do this: Right click in right hand pane and select Move to Phones List Select the device type, e.g. 52xx/53xx and click Next Select extensions that you want to move and click Move Items button Click Finish To view and move SIP Trunk Groups to the Call Configuration: Navigate to System->IP-Related Information->Call Configurations-><call configuration number> Click SIP Trunk Groups Right click in right hand pane and select Move to SIP Trunk Groups List Select the type, e.g. SIP Trunk Group and click Next Select the required trunk group that you want to move and click Move Items button Click Finish 17
22 Adtran 908e Configuration settings (Optional) Adtran IP Business Gateway was configured as a Back2Back agent to enable SIP communication between EarthLink and Mitel EarthLink provides the configuration file for this type of gateway. This file contains all required settings to configure the gateway to connect to EarthLink SIP trunk. So, every configuration file is a site specific. Below, just for reference, we provide the configuration file loaded in Adtran Total Access 908e for our test environment. ADTRAN, Inc. OS version A E Boot ROM version SA Platform: Total Access 908e (2nd Gen), part number L1 Serial number CFG hostname "MITEL_LAB_908e" enable password test; set password to access Adtran s config mode clock timezone -5-Eastern-Time ip subnet-zero ip classless ip routing ip domain-proxy ip name-server no auto-config event-history on no logging forwarding no logging no service password-encryption username "admin" password "123456"; set name and password for web access ip policy-timeout tcp telnet ip policy-timeout udp ip firewall no ip firewall alg msn no ip firewall alg mszone no ip firewall alg h323 no dot11ap access-point-control
23 qos map VOICE 10 match dscp 46 match list DNS priority percent 90 interface eth 0/1 description MITEL_LAB speed 100 ip address ; Adtran s internal interface access-policy Private media-gateway ip primary no shutdown interface eth 0/2 description MITEL_PUBLIC_WAN_IP speed 100 ip address ; Adtran s external interface access-policy Public media-gateway ip primary max-reserved-bandwidth 100 qos-policy out VOICE no shutdown interface t1 0/1 shutdown interface t1 0/2 shutdown interface t1 0/3 shutdown interface t1 0/4 shutdown interface fxs 0/1 no shutdown interface fxs 0/2 no shutdown interface fxs 0/3 no shutdown interface fxs 0/4 19
24 no shutdown interface fxs 0/5 no shutdown interface fxs 0/6 no shutdown interface fxs 0/7 no shutdown interface fxs 0/8 no shutdown interface fxo 0/0 no shutdown ip access-list standard DATA permit any ip access-list standard MATCH_ALL permit ip access-list extended DNS permit tcp any host permit tcp any host permit tcp any host permit tcp any host ip access-list extended HOSTED_VOICE_LIST remark NAT list HOSTED_VOICE_LIST permit ip any host permit ip any host permit ip any host permit ip any permit ip any permit ip any permit ip any permit ip any permit ip any permit ip any permit ip any permit ip any host permit ip any permit ip any permit ip any host ip access-list extended REMOTE_MANAGEMENT_ACCESS permit tcp any any eq www log
25 permit tcp any any eq telnet log permit udp any any eq snmp log permit tcp any any eq https log permit tcp any any eq ssh log permit tcp any any eq ftp log permit icmp any any echo log ip access-list extended VOICE_WAN permit udp any any eq 5060 permit tcp any any eq 5060 ip policy-class Private allow list MATCH_ALL self nat source list HOSTED_VOICE_LIST address overload nat source list DATA address overload ip policy-class Public allow list REMOTE_MANAGEMENT_ACCESS allow list VOICE_WAN ip route no ip tftp server no ip tftp server overwrite ip http server ip http secure-server no ip snmp agent ip ftp server no ip scp server no ip sntp server snmp-server community ITC-PubliC RO auto-link ip sip ip sip udp 5060 ip sip tcp 5060 voice feature-mode network voice forward-mode network voice dial-plan 1 local NXX-NXX-XXXX voice dial-plan 2 long-distance 1-NXX-NXX-XXXX 21
26 voice codec-list G.711_only codec g711ulaw voice ani-list ALL_ANI ani $ voice trunk-list METASWITCH_SIP_LINES trunk T01 voice trunk T01 type sip description "SIP Line to LAB Meta" sip-server primary sbc.voiplab.deltacom.net codec-group G.711_only voice trunk T10 type analog supervision loop-start connect fxo 0/0 rtp delay-mode adaptive voice grouped-trunk METASWITCH_SIP_LINES description "SIP_Lines_to_Metaswitch" trunk T01 accept $ cost 0 deny proxy permit list ALL_ANI deny all other trunks deny all other ani voice grouped-trunk FXO_01 trunk T10 accept $ cost 10 deny list METASWITCH_SIP_LINES permit proxy permit list ALL_ANI deny all other trunks deny all other ani voice user 01 password "1234" description "SIP_IDENTITY_USER" sip-identity metaswitch T01 sip-authentication password "1234" voice user connect fxs 0/1 first-name "Adtran908e_ST" last-name "FXS_0/2" password "1234"
27 no special-ring-cadences sip-identity T01 register auth-name " " password "deltacom" sip-authentication password "deltacom" modem-passthrough codec-group G.711_only ip sip default-call-routing switchboard ip sip proxy ip sip proxy sip-server primary static.voiplab.deltacom.net ip sip proxy user-template IP_PBX target udp 5060; IP address of Mitel 5000CP proxy-mode stateful reject reject accept $ ip sip qos dscp 46 ip rtp quality-monitoring ip rtp quality-monitoring sip line con 0 no login line telnet 0 4 login password tinman no shutdown line ssh 0 4 login local-userlist no shutdown sntp server sntp wait-time 60 End 23
28
MITEL SIP CoE. Technical. Configuration Notes. Configure MCD 4.1 SP1 for use with the Lyrix Speech Enabled Auto Attendant
MITEL SIP CoE Technical Configuration Notes Configure MCD 4.1 SP1 for use with the Lyrix Speech Enabled Auto Attendant NOTICE The information contained in this document is believed to be accurate in all
More informationTechnical Configuration Notes
MITEL SIP CoE Technical Configuration Notes Configure MiVoice Office 250 6.0 SP2 with MBG for use with Time Warner Cable Business Class SIP Trunking service MARCH 2015 SIP COE 15-4940-00364 TECHNICAL CONFIGURATION
More informationTechnical Configuration Notes
MITEL SIP CoE Technical Configuration Notes Configure MCD for use with OpenIP SIP Trunking service SIP CoE 11-4940-00186 NOTICE The information contained in this document is believed to be accurate in
More informationMitel- SIP CoE. Technical. Configuration Notes. How to Guide to Configure the Mitel 5000 CP 4.0 R24 for use with Integra Telecom
Mitel- SIP CoE Technical Configuration Notes How to Guide to Configure the Mitel 5000 CP 4.0 R24 for use with Integra Telecom NOTICE The information contained in this document is believed to be accurate
More informationMITEL SIP CoE. Technical. Configuration Notes. Configure the Mitel 3300 MCD 4.1 for use with Paetec Broadworks Softswitch. SIP CoE 08-4940-00035
MITEL SIP CoE Technical Configuration Notes Configure the Mitel 3300 MCD 4.1 for use with Broadworks Softswitch SIP CoE 08-4940-00035 NOTICE The information contained in this document is believed to be
More informationMITEL SIP CoE. Technical. Configuration Notes. Configure MCD 4.1 for use with SKYPE SIP Trunking. SIP CoE 10-4940-00120
MITEL SIP CoE Technical Configuration Notes Configure MCD 4.1 for use with SKYPE SIP Trunking SIP CoE 10-4940-00120 NOTICE The information contained in this document is believed to be accurate in all respects
More informationMITEL SIP CoE. Technical. Configuration Notes. Configure MCD 6.X for use with babytel SIP trunks. SIP CoE 13-4940-00266
MITEL SIP CoE Technical Configuration Notes Configure MCD 6.X for use with babytel SIP trunks SIP CoE 13-4940-00266 NOTICE The information contained in this document is believed to be accurate in all respects
More informationMITEL SIP CoE. Technical. Configuration Note. Configure MCD for use with Intelepeer Service provider SIP Trunking. SIP CoE 14-4940-00313
MITEL SIP CoE Technical Configuration Note Configure MCD for use with Intelepeer Service provider SIP Trunking SIP CoE 14-4940-00313 NOTICE The information contained in this document is believed to be
More informationMITEL SIP CoE. Technical. Configuration Notes. Configure Ascom i62 phones for use with MiVoice Office. SIP CoE 14-4940-00310
MITEL SIP CoE Technical Configuration Notes Configure Ascom i62 phones for use with MiVoice Office SIP CoE 14-4940-00310 NOTICE The information contained in this document is believed to be accurate in
More informationMITEL SIP CoE Technical. Configuration Note. Configure MCD for use with Thinktel SIP Trunking Service. SIP CoE 12-4940-00197
MITEL SIP CoE Technical Configuration Note Configure MCD for use with SIP Trunking Service SIP CoE NOTICE The information contained in this document is believed to be accurate in all respects but is not
More informationA2.03 AdTran NetVanta 1355/6355 SIP/TDM/IP Appliance
A2.03 AdTran NetVanta 1355/6355 SIP/TDM/IP Appliance 1 Important Notes Check the SIP 3 rd Party Validation Website for current validation status. The SIP 3 rd Part Validation Website can be viewed at:
More informationTechnical Configuration Notes
MITEL SIPCoE Technical Configuration Notes Configure Mitel UC360 SIP Phone and Mitel MCD for use with VidyoWay SIP CoE 13-4940-00228 NOTICE The information contained in this document is believed to be
More informationTechnical Configuration Notes
MITEL SIPCoE Technical Configuration Notes Configure Inn-Phone SIP Phone for use with MCD SIP CoE NOTICE The information contained in this document is believed to be accurate in all respects but is not
More informationTechnical Configuration Notes
MITEL SIPCoE Technical Configuration Notes Configure the MCD 6.0 for use with the Commend SIP Doorphone SIP CoE 13-4940-00251 NOTICE The information contained in this document is believed to be accurate
More informationUsing the NetVanta 7100 Series
MENU OK CANCEL 1 2 3 4 5 6 7 8 9 * 0 # MENU MENU OK CANCEL CANCEL 1 2 3 4 5 6 7 8 9 * 0 # MENU OK CANCEL CANCEL 1 2 3 4 5 6 7 8 9 * 0 # MENU OK CANCEL CANCEL 1 2 3 4 5 6 7 8 9 * 0 # MENU OK CANCEL 1 2
More informationEarthLink Business SIP Trunking. Adtran 7100 IP PBX Customer Configuration Guide
EarthLink Business SIP Trunking Adtran 7100 IP PBX Customer Configuration Guide Publication History First Release: Version 1.0 January 23, 2013 CHANGE HISTORY Version Date Change Details Changed By 1.0
More informationADTRAN SBC and Cisco Unified Call Manager SIP Trunk Interoperability
6AOSSG0004-42A April 2013 Interoperability Guide ADTRAN SBC and Cisco Unified Call Manager SIP Trunk Interoperability This guide describes an example configuration used in testing the interoperability
More informationADTRAN SBC and Avaya IP Office PBX SIP Trunk Interoperability
6AOSSG001-42B March 2014 Interoperability Guide ADTRAN SBC and Avaya IP Office PBX SIP Trunk Interoperability This guide describes an example configuration used in testing the interoperability of an ADTRAN
More informationEarthLink Business SIP Trunking. ININ IC3 IP PBX Customer Configuration Guide
EarthLink Business SIP Trunking ININ IC3 IP PBX Customer Configuration Guide Publication History First Release: Version 1.0 August 30, 2011 CHANGE HISTORY Version Date Change Details Changed By 1.0 8/30/2011
More informationApplication Notes for BT Wholesale/HIPCOM SIP Trunk Service and Avaya IP Office 8.0 Issue 1.0
Avaya Solution & Interoperability Test Lab Application Notes for BT Wholesale/HIPCOM SIP Trunk Service and Avaya IP Office 8.0 Issue 1.0 Abstract These Application Notes describe the procedures for configuring
More informationEarthLink Business SIP Trunking. Switchvox SMB 5.5 & Adtran SIP Proxy Implementation Guide
EarthLink Business SIP Trunking Switchvox SMB 5.5 & Adtran SIP Proxy Implementation Guide Publication History First Release: Version 1.0 April 20, 2012 CHANGE HISTORY Version Date Change Details Changed
More informationHow to Configure the NEC SV8100 for use with Integra Telecom SIP Solutions
How to Configure the NEC SV8100 for use with Integra Telecom SIP Solutions Overview: This document provides a reference for configuration of the NEC SV8100 IP PBX to connect to Integra Telecom SIP trunks.
More informationApplication Notes for Configuring Avaya IP Office 9.0 with HIPCOM SIP Trunk Issue 1.0
Avaya Solution & Interoperability Test Lab Application Notes for Configuring Avaya IP Office 9.0 with HIPCOM SIP Trunk Issue 1.0 Abstract These Application Notes describe the procedures for configuring
More informationApplication Notes for Avaya IP Office 7.0 Integration with Skype Connect R2.0 Issue 1.0
Avaya Solution & Interoperability Test Lab Application Notes for Avaya IP Office 7.0 Integration with Skype Connect R2.0 Issue 1.0 Abstract These Application Notes describe the steps to configure an Avaya
More informationApplication Notes for Configuring Intelepeer SIP Trunking with Avaya IP Office 7.0 - Issue 1.0
Avaya Solution & Interoperability Test Lab Application Notes for Configuring Intelepeer SIP Trunking with Avaya IP Office 7.0 - Issue 1.0 Abstract These Application Notes describe the procedures for configuring
More informationInteractive Intelligence CIC 2015 R4 Patch1 Configuration Guide
Interactive Intelligence CIC 2015 R4 Patch1 Configuration Guide Performed By tekvizion PVS, Inc. Contact: 214-242-5900 www.tekvizion.com Copyright 2015 by tekvizion PVS, Inc. All Rights Reserved. Confidential
More informationApplication Notes for Configuring Cablevision Optimum Voice SIP Trunking with Avaya IP Office - Issue 1.1
Avaya Solution & Interoperability Test Lab Application Notes for Configuring Cablevision Optimum Voice SIP Trunking with Avaya IP Office - Issue 1.1 Abstract These Application Notes describe the procedures
More informationAvaya IP Office 8.1 Configuration Guide
Avaya IP Office 8.1 Configuration Guide Performed By tekvizion PVS, Inc. Contact: 214-242-5900 www.tekvizion.com Revision: 1.1 Date: 10/14/2013 Copyright 2013 by tekvizion PVS, Inc. All Rights Reserved.
More informationHow to Configure the Allworx 6x, 24x and 48x for use with Integra Telecom SIP Solutions
How to Configure the Allworx 6x, 24x and 48x for use with Integra Telecom SIP Solutions Overview: This document provides a reference for configuration of the Allworx 6x IP PBX to connect to Integra Telecom
More informationConfiguring SIP Trunking and Networking for the NetVanta 7000 Series
61200796L1-29.4E July 2011 Configuration Guide Configuring for the NetVanta 7000 Series This configuration guide describes the configuration and implementation of Session Initiation Protocol (SIP) trunking
More informationConfiguring for Integra Telecom SIP Solutions
February 2013 Configuring for Integra Telecom SIP Solutions Section Title Page Background 1 Table 1 Software & Firmware Versions Tested 1 Figure 1 Generic IP PBX Test Configuration (with Transparent SIP
More informationHow to Configure the Cisco UC500 for use with Integra Telecom SIP Solutions
How to Configure the Cisco UC500 for use with Integra Telecom SIP Solutions Overview: This document provides a reference for configuration of the Cisco UC500 IP PBX to connect to Integra Telecom SIP Trunks.
More informationCisco Unified Communications 500 Series
Cisco Unified Communications 500 Series IP PBX Provisioning Guide Version 1.0 Last Update: 02/14/2011 Page 1 DISCLAIMER The attached document is provided as a basic guideline for setup and configuration
More information1 SIP Carriers. 1.1 Tele2. 1.1.1 Warnings. 1.1.2 Vendor Contact. 1.1.3 Versions Verified Interaction Center 2015 R2 Patch1. 1.1.
1 SIP Carriers 1.1 Tele2 1.1.1 Warnings Check the SIP 3 rd Party SIP Carrier Matrix for certification status, and supported features. More info about the SIP 3 rd Party SIP Carrier Matrix can be found
More informationApplication Notes for Configuring Broadvox SIP Trunking with Avaya IP Office - Issue 1.0
Avaya Solution & Interoperability Test Lab Application Notes for Configuring Broadvox SIP Trunking with Avaya IP Office - Issue 1.0 Abstract These Application Notes describe the procedures for configuring
More informationHow To Connect A Phone To An Ip Trunk On A Cell Phone On A Sim Sim Simlia (Vizon) Or Ip Office (Izon) On A Ppl (Telnet) On An Ip Office Softphone On A Vnet (V
Avaya Solution & Interoperability Test Lab Application Notes for SIP Trunking Using Verizon Business IP Trunk SIP Trunk Service and Avaya IP Office Release 7.0 Issue 1.1 Abstract These Application Notes
More informationHow to Configure the Toshiba Strata CIX for use with Integra Telecom SIP Solutions
How to Configure the Toshiba Strata CIX for use with Integra Telecom SIP Solutions Overview: This document provides a reference for configuration of the Toshiba Strata CIX IP PBX to connect to Integra
More informationEarthLink Business SIP Trunking. NEC SV8300 IP PBX Customer Configuration Guide
EarthLink Business SIP Trunking NEC SV8300 IP PBX Customer Configuration Guide Publication History First Release: Version 1.0 May 18, 2012 CHANGE HISTORY Version Date Change Details Changed By 1.0 5/18/2012
More informationIP PBX. SD Card Slot. FXO Ports. PBX WAN port. FXO Ports LED, RED means online
1 IP PBX SD Card Slot FXO Ports PBX LAN port PBX WAN port FXO Ports LED, RED means online 2 Connect the IP PBX to Your LAN Internet PSTN Router Ethernet Switch FXO Ports 3 Access the PBX s WEB GUI The
More informationEarthLink Business SIP Trunking. NEC SV8100 IP PBX Customer Configuration Guide
EarthLink Business SIP Trunking NEC SV8100 IP PBX Customer Configuration Guide Publication History First Release: Version 1.0 August 30, 2011 CHANGE HISTORY Version Date Change Details Changed By 1.0 8/30/2011
More informationApplication Notes for Configuring Avaya IP Office 8.1 with Colt VoIP Access service Issue 1.0
Avaya Solution & Interoperability Test Lab Application Notes for Configuring Avaya IP Office 8.1 with Colt VoIP Access service Issue 1.0 Abstract These Application Notes describe the procedures for configuring
More informationApplication Notes for SIP Trunking Using Verizon Business IP Trunk SIP Trunk Service and Avaya IP Office Release 7.0 Issue 1.0
Avaya Solution & Interoperability Test Lab Application Notes for SIP Trunking Using Verizon Business IP Trunk SIP Trunk Service and Avaya IP Office Release 7.0 Issue 1.0 Abstract These Application Notes
More informationIntegrating Skype for SIP with UC500
Integrating Skype for SIP with UC500 Version 1.1 2008 Cisco Systems, Inc. All rights reserved. 1 TABLE OF CONTENTS 1 OVERVIEW... 3 1.1 INTRODUCTION... 3 1.2 SCOPE... 3 1.3 REVISION CONTROL... 3 1.4 RESTRICTIONS...
More informationConfiguring the NetVanta 7100 for Operation with Polycom s SpectraLink Wireless Telephones
6AOSCG0007-29A October 2010 Configuration Guide Configuring the NetVanta 7100 for Operation with Polycom s SpectraLink Wireless Telephones This configuration guide describes the configuration of the NetVanta
More informationEarthLink Business SIP Trunking. Toshiba IPedge Customer Configuration Guide
EarthLink Business SIP Trunking Toshiba IPedge Customer Configuration Guide Publication History First Release: Version 1.0 August 30, 2011 CHANGE HISTORY Version Date Change Details Changed By 1.0 8/30/2011
More informationApplication Notes for Configuring Broadvox SIP Trunking with Avaya IP Office Release 8.0 Issue 1.0
Avaya Solution & Interoperability Test Lab Application Notes for Configuring Broadvox SIP Trunking with Avaya IP Office Release 8.0 Issue 1.0 Abstract These Application Notes describe the steps necessary
More informationnexvortex Setup Guide
nexvortex Setup Guide CISCO UC500 March 2012 Introduction This document is intended only for nexvortex customers and resellers as an aid to setting up the Cisco PBX software to connect to the nexvortex
More informationSIP Trunking Configuration Guide for Mitel 5000 v6.0 IP-PBX
October 14, 2014 SIP Trunking Configuration Guide for Mitel 5000 v6.0 IP-PBX Page 1 of 19 Table of Contents 1 Overview... 3 1.1 Prerequisites... 3 2 Network Topology... 4 3 Description of Basic Operation
More informationInstallation and Maintenance Guide Release 1.0
Installation and Maintenance Guide Release 1.0 NOTICE The information contained in this document is believed to be accurate in all respects but is not warranted by Mitel Networks Corporation (MITEL ).
More informationEarthLink Business SIP Trunking. Avaya IPO IP PBX Customer Configuration Guide
EarthLink Business SIP Trunking Avaya IPO IP PBX Customer Configuration Guide Publication History First Release: Version 1.0 August 30, 2011 CHANGE HISTORY Version Date Change Details Changed By 1.0 8/30/2011
More informationSBC 1000 / SBC 2000 Series Configuration Guide (For Microsoft Lync Server 2013)
Configuration Guide SBC 1000 / SBC 2000 Series Configuration Guide (For Microsoft Lync Server 2013) For use with AT&T s IP Flexible Reach Enhanced Features Service on MIS, MPLS PNT or AT&T VPN Disclaimers
More information6.40A AudioCodes Mediant 800 MSBG
AudioCodes Mediant 800 MSBG Page 1 of 66 6.40A AudioCodes Mediant 800 MSBG 1. Important Notes Check the SIP 3 rd Party Validation Website for current validation status. The SIP 3 rd party Validation Website
More informationApplication Notes for Configuring OneStream SIP Trunking with Avaya IP Office Release 8.1 Issue 0.1
Avaya Solution & Interoperability Test Lab Application Notes for Configuring OneStream SIP Trunking with Avaya IP Office Release 8.1 Issue 0.1 Abstract These Application Notes describes the steps to configure
More informationAbstract. Avaya Solution & Interoperability Test Lab
Avaya Solution & Interoperability Test Lab Application Notes for Configuring SIP Trunking between the Verizon Business VoIP Service with IP Trunking and Avaya Communication Manager Branch Edition Issue
More informationTechnical Configuration Notes
MITEL MSA 3PPV Technical Configuration Notes Configure the 5000 CP for use with the Polycom Spectralink 8400 Series SIP Wireless device SIP CoE 11-4940-00177 NOTICE The information contained in this document
More informationSIP Trunk Configuration V/IPedge Feature Description 5/22/13
SIP Trunk Configuration V/IPedge Feature Description 5/22/13 OVERVIEW Session Initiation Protocol (SIP) is an application layer protocol used for establishing sessions in an IP network. SIP trunks allow
More informationApplication Note Startup Tool - Getting Started Guide
Application Note Startup Tool - Getting Started Guide 1 April 2012 Startup Tool Table of Contents 1 INGATE STARTUP TOOL... 1 2 STARTUP TOOL INSTALLATION... 2 3 CONNECTING THE INGATE FIREWALL/SIPARATOR...
More informationnexvortex SIP Trunking
nexvortex SIP Trunking January 2015 510 SPRING STREET HERNDON VA 20170 +1 855.639.8888 Copyright nexvortex 2014 This document is the exclusive property of nexvortex, Inc. and no part may be disclosed,
More informationFortiVoice. Version 7.00 VoIP Configuration Guide
FortiVoice Version 7.00 VoIP Configuration Guide FortiVoice Version 7.00 VoIP Configuration Guide Revision 2 14 October 2011 Copyright 2011 Fortinet, Inc. All rights reserved. Contents and terms are subject
More informationNetVanta 7100 Exercise Service Provider SIP Trunk
NetVanta 7100 Exercise Service Provider SIP Trunk PSTN NetVanta 7100 FXS 0/1 x2001 SIP Eth 0/0 x2004 SIP Server 172.23.102.87 Hosted by x2003 www.voxitas.com In this exercise, you will create a SIP trunk
More informationVega 100G and Vega 200G Gamma Config Guide
Vega 100G and Vega 200G Gamma Config Guide This document aims to go through the steps necessary to configure the Vega SBC to be used with a Gamma SIP Trunk. When a SIP trunk is provisioned by Gamma a list
More informationnexvortex Setup Template
nexvortex Setup Template ZULTYS, INC. April 2013 5 1 0 S P R I N G S T R E E T H E R N D O N V A 2 0 1 7 0 + 1 8 5 5. 6 3 9. 8 8 8 8 Introduction This document is intended only for nexvortex customers
More information1 SIP Carriers. 1.1 Tele2. 1.1.1 Warnings. 1.1.2 Vendor Contact. 1.1.3 Versions Verified SIP Carrier status as of Jan 1, 2011. 1.1.
1 SIP Carriers 1.1 Tele2 1.1.1 Warnings Check the SIP 3 rd Party SIP Carrier Matrix for certification status, and supported features. More info about the SIP 3 rd Party SIP Carrier Matrix can be found
More informationHow To Configure Aastra Clearspan For Aastro (Turbos) And Bpb (Broadworks) On A Pc Or Macbook (Windows) On An Ipa (Windows Xp) On Pc Or Ipa/
BroadSoft Partner Configuration Guide Aastra Clearspan TM April 2011 Document Version 1.4 2811 Internet Blvd. Frisco, TX 75034, U.S.A Tel: 469-365-3237 Fax: 469-365-3071 WWW.AASTRA.COM BroadWorks Guide
More informationConfiguring Interactive Intelligence ININ IP PBX For tw telecom SIP Trunking service USER GUIDE
Configuring Interactive Intelligence ININ IP PBX For tw telecom SIP Trunking service USER GUIDE Version 1.0 August 23, 2012 Copyright 2012 by tw telecom inc. All Rights Reserved. This document is the property
More informationSIP Trunking Quick Reference Document
SIP Trunking Quick Reference Document Publication Information SAMSUNG TELECOMMUNICATIONS AMERICA reserves the right without prior notice to revise information in this publication for any reason. SAMSUNG
More informationOptimum Business SIP Trunk Set-up Guide
Optimum Business SIP Trunk Set-up Guide For use with IP PBX only. SIPSetup 07.13 FOR USE WITH IP PBX ONLY Important: If your PBX is configured to use a PRI connection, do not use this guide. If you need
More informationEarthLink Business SIP Trunking. Asterisk 11.2 IP PBX Customer Configuration Guide
EarthLink Business SIP Trunking Asterisk 11.2 IP PBX Customer Configuration Guide Publication History First Release: Version 1.0 August 30, 2011 CHANGE HISTORY Version Date Change Details Changed By 1.0
More informationSBC 1000/2000 Configuration Guide with Lync 2013 for Windstream/ LPAETEC SIP Trunk Deployments
SBC 1000/2000 Configuration Guide with Lync 2013 for Windstream/ LPAETEC SIP Trunk Deployments Application Notes Rev. 1.0 Last Updated: April 10, 2015 Revision Date Revised By Comments 0.1 12/03/2015 Roman
More informationSample Configuration for SIP Trunking between Avaya IP Office R8.0 and Cisco Unified Communications Manager 8.6.2 Issue 1.0
Avaya Solution & Interoperability Test Lab Sample Configuration for SIP Trunking between Avaya IP Office R8.0 and Cisco Unified Communications Manager 8.6.2 Issue 1.0 Abstract These Application Notes describe
More informationBroadvox SIP Trunk Setup
DSX Broadvox SIP Trunk Setup April 22, 2011 Issue 1.05 NEC Corporation of America 4 Forest Parkway, Shelton, CT 06484 DSX DSX SIP Trunk Setup Issue 1.05 Copyright 2011 NEC Corporation of America 6535 N.
More informationBackground 1 Table 1 Software & Firmware Versions Tested 1 Figure 1 Integra s Universal Access (UA) IP PBX Test Configuration 1
1 Background 1 Table 1 Software & Firmware Versions Tested 1 Figure 1 Integra s Universal Access (UA) IP PBX Test Configuration 1 Configuration Data 2 Section 1: Initial IPitomy IP PBX Connection & Login
More information1.1.3 Versions Verified SIP Carrier status as of 18 Sep 2014 : validated on CIC 4.0 SU6.
1 SIP Carriers 1.1 Telstra 1.1.1 Warnings Check the SIP 3 rd Party SIP Carrier Matrix for certification status, and supported features. More info about the SIP 3 rd Party SIP Carrier Matrix can be found
More information3CX PBX v12.5. SIP Trunking using the Optimum Business Sip Trunk Adaptor and the 3CX PBX v12.5
SIP Trunking using the Optimum Business Sip Trunk Adaptor and the 3CX PBX v12.5 Table of Contents 1. Overview 3 2. Prerequisites 3 3. PBX Configuration 3 4. Creating Extensions 4 5. VoIP Provider Setup
More informationApplication Note Configuring the Synapse SB67070 SIP Gateway for Broadvox GO! SIP Trunking
Configuring the Synapse SB67070 SIP Gateway for Broadvox GO! SIP Trunking 2012 Advanced American Telephones. All Rights Reserved. AT&T and the AT&T logo are trademarks of AT&T Intellectual Property licensed
More informationUsing LifeSize systems with Microsoft Office Communications Server 2007. Server Setup
Using LifeSize systems with Microsoft Office Communications Server 2007 This technical note describes the steps to integrate a LifeSize video communications device with Microsoft Office Communication Server
More informationLink2VoIP SIP Trunk Setup
DSX Link2VoIP SIP Trunk Setup April 23, 2011 Issue 1.00 NEC Corporation of America 4 Forest Parkway, Shelton, CT 06484 Copyright 2011 NEC Corporation of America 6535 N. State Highway 161 Irving, TX 75039-2402
More informationApplication Notes for Configuring Yealink T-22 SIP Phones to interoperate with Avaya IP Office - Issue 1.0
Avaya Solution & Interoperability Test Lab Application Notes for Configuring Yealink T-22 SIP Phones to interoperate with Avaya IP Office - Issue 1.0 Abstract These Application Notes describe the configuration
More informationLifeSize Video Communications Systems Administrator Guide
LifeSize Video Communications Systems Administrator Guide November 2009 Copyright Notice 2005-2009 LifeSize Communications Inc, and its licensors. All rights reserved. LifeSize Communications has made
More informationApplication Notes for DuVoice Emergency Alert System with Avaya IP Office 9.0 Issue 1.0
Avaya Solution & Interoperability Test Lab Application Notes for DuVoice Emergency Alert System with Avaya IP Office 9.0 Issue 1.0 Abstract These Application Notes describe the configuration steps required
More informationGW400 VoIP Gateway. User s Guide
GW400 VoIP Gateway User s Guide P/N: 956YD30001 Copyright 2006. All Rights Reserved. Document Version: 1.0 All trademarks and trade names are the properties of their respective owners. i Table of Contents
More informationVoIP Network Configuration Guide
The owner friendly phone system for small business VoIP Network Configuration Guide Release 7.10 Copyright 2011 Fortinet, Inc. All rights reserved. Fortinet, FortiGate, FortiGuard, FortiCare, FortiManager,
More informationMyIC setup and configuration (with sample configuration for Alcatel Lucent test environment)
MyIC setup and configuration (with sample configuration for Alcatel Lucent test environment) N.B. Goto MyIC Preferences in the System Toolbar. Description: this may be any appropriate description of the
More informationEarthLink Business SIP Trunking. Cisco Call Manager and Cisco CUBE Customer Configuration Guide
EarthLink Business SIP Trunking Cisco Call Manager and Cisco CUBE Customer Configuration Guide Publication History First Release: Version 2.0 April 20, 2012 CHANGE HISTORY Version Date Change Details Changed
More informationMIVOICE BORDER GATEWAY PLATFORM
MITEL MIVOICE BORDER GATEWAY PLATFORM MiVoice Border Gateway Remote Phone Configuration Guide FEBRUARY, 2016 RELEASE 9.2 MBG - Remote IP Phone Configuration Guide NOTICE The information contained in this
More informationApplication Note. Onsight Mobile Collaboration Video Endpoint Interoperability v5.0
Application Note Onsight Mobile Collaboration Video Endpoint Interoperability v5. Onsight Mobile Collaboration Video Endpoint Interoperability... 3 Introduction... 3 Adding Onsight to a Video Conference
More informationApplication Notes for Revolabs FLX UC 1000 with Avaya IP Office - Issue 0.1
Avaya Solution & Interoperability Test Lab Application Notes for Revolabs FLX UC 1000 with Avaya IP Office - Issue 0.1 Abstract These Application Notes describe the configuration steps required to integrate
More informationApplication Notes for Configuring SIP Trunking between McLeodUSA SIP Trunking Solution and an Avaya IP Office Telephony Solution 1.
Avaya Solution & Interoperability Test Lab Application Notes for Configuring SIP Trunking between McLeodUSA SIP Trunking Solution and an Avaya IP Office Telephony Solution 1.0 Abstract These Application
More informationAbstract. Avaya Solution & Interoperability Test Lab
Avaya Solution & Interoperability Test Lab Application Notes for Configuring SIP Trunking Using Verizon Business IP Contact Center VoIP Inbound and Avaya IP Office Release 8 with Avaya Session Border Controller
More informationApplication Notes Rev. 1.0 Last Updated: January 9, 2015
SBC 1000/2000 Series Configuration Guide with Cisco Unified Call Manager v9.1 for Level 3 Voice Complete SM SIP Trunk Deployments Application Notes Rev. 1.0 Last Updated: January 9, 2015 Contents 1 Document
More informationMediatrix 3000 with Asterisk June 22, 2011
Mediatrix 3000 with Asterisk June 22, 2011 Proprietary 2011 Media5 Corporation Table of Contents Introduction... 3 Network Topology... 3 Equipment Detail... 3 Configuration of the Fax Extension... 4 Configuration
More informationLifeSize UVC Multipoint Deployment Guide
LifeSize UVC Multipoint Deployment Guide May 2014 LifeSize UVC Multipoint Deployment Guide 2 LifeSize UVC Multipoint LifeSize UVC Multipoint is a software MCU optimized for conferences that mix high definition
More informationSIP Trunking using Optimum Business SIP Trunk Adaptor and the Cisco Call Manager Express Version 8.5
CISCO SIP Trunking using Optimum Business SIP Trunk Adaptor and the Cisco Call Manager Express Version 8.5 Goal The purpose of this configuration guide is to describe the steps needed to configure the
More informationAT&T IP Flex Reach/ IP Toll Free Configuration Guide IC 3.0 with Interaction SIP Proxy
INTERACTIVE INTELLIGENCE AT&T IP Flex Reach/ IP Toll Free Configuration Guide IC 3.0 with Interaction SIP Proxy Version 1.7 9/2/2009 TABLE OF CONTENTS 1 AT&T... 5 1.1 Introduction... 5 1.2 Product Descriptions...
More informationHow to Configure the Avaya IP Office 6.1 for use with Integra Telecom SIP Solutions
How to Configure the Avaya IP Office 6.1 for use with Integra Telecom SIP Solutions Overview This document provides a reference for configuration of the Avaya IP Office to connect to Integra Telecom SIP
More informationSIP Trunking using the EdgeMarc Network Services Gateway and the Mitel 3300 ICP IP-PBX
June 26th, 2014 SIP Trunking using the EdgeMarc Network Services Gateway and the Mitel 3300 ICP IP-PBX Page 1 of 30 Table of Contents 1 Overview... 3 2 Prerequisites... 3 3 Network Topology... 4 4 Description
More informationConfiguring Shared Line Appearances over Analog Trunks
61200796L1-29.1G March 2013 Configuration Guide Configuring Shared Line Appearances over Analog Trunks This configuration guide explains how to configure shared line appearances (SLAs) on AOS voice products
More informationSIP Trunking Manual 05.15. Technical Support Web Site: http://ws1.necii.com (registration is required)
SIP Trunking Manual 05.15 Technical Support Web Site: http://ws1.necii.com (registration is required) This manual has been developed by NEC Unified Solutions, Inc. It is intended for the use of its customers
More informationConfiguring Avaya 1120E, 1140E, 1220 and 1230 IP Deskphones with Avaya IP Office Release 6.1 Issue 1.0
Avaya Solution & Interoperability Test Lab Configuring Avaya 1120E, 1140E, 1220 and 1230 IP Deskphones with Avaya IP Office Release 6.1 Issue 1.0 Abstract These Application Notes describe a solution comprised
More information