1 Operating Instructions DLP Based Projector Commercial Use Model No. PT-D5700U PT-D5700UL PT-DW5100U PT-DW5100UL Read these instructions completely before operating this unit. TQBJ0219
2 Dear Panasonic Customer: This instruction booklet provides all the necessary operating information that you might require. We hope it will help you to get the most performance out of your new product, and that you will be pleased with your Panasonic DLP based projector. The serial number of your product may be found on its back. You should note it in the space provided below and retain this booklet in case service is required. Model number: PT-D5700U/PT-D5700UL/PT-DW5100U/PT-DW5100UL Serial number: IMPORTANT SAFETY NOTICE WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. MISE EN GARDE- WARNUNG- WARNING RISK OF ELECTRIC SHOCK. DO NOT OPEN RISQUE DE CHOC ÉLECTRIQUE. NE PAS OUVRIR. ZUR VERMEIDUNG EINES ELEKTRISCHEN SCHLAGES GERÄT NICHT ÖFFNEN. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated dangerous voltage within the Product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The eclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. CAUTION: This equipment is equipped with a three-pin grounding-type power plug. Do not remove the grounding pin on the power plug. This plug will only fit a grounding-type power outlet. This is a safety feature. If you are unable to insert the plug into the outlet, contact an electrician. Do not defeat the purpose of the grounding plug. Do not remove 2
3 WARNING: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an eperienced radio/tv technician for help. FCC CAUTION: To assure continued compliance, use only shielded interface cables when connecting to computer or peripheral devices. Any unauthorized changes or modifications to this equipment could void the user s authority to operate. WARNING: Not for use in a computer room as defined in the Standard for the Protection of Electronic Computer/Data Processing Equipment, ANSI/NFPA 75. Declaration of Conformity Model Number: PT-D5700U/PT-D5700UL/PT-DW5100U/PT-DW5100UL Trade Name: Panasonic Responsible Party: Panasonic Corporation of North America One Panasonic Way, Secaucus, New Jersey Telephone Number: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE: This product has a High Intensity Discharge (HID) lamp that contains mercury. Dispose may be regulated in your community due to environmental considerations. For disposal or recycling information, please contact your local authorities, or the Electronic Industries Alliance: 3
4 Contents 4 IMPORTANT SAFETY NOTICE...2 Precautions with regard to safety...5 Accessories...7 Precautions on handling...8 Name and function of parts...9 Remote control...9 Front and side of the projector...11 Rear view of the main unit/controls on rear panel...12 Side-mounted connection terminals...13 Using the remote control unit...14 Loading dry cells...14 Effective range of remote control operation...14 Setting projector ID number to remote control...15 Connect to the projector to use with a cable...15 Installation...16 Projection schemes...16 Installation geometry...16 Projection distance by projection lens...17 Calculation formulas for projection distance by lens types..21 Connection...22 Setup precautions...22 Eample of connecting with AV products...23 Eample of connecting with PCs...23 Projection...24 Powering up the projector...24 Making adjustment and selection...24 Powering off the projector...25 Direct power off function...25 How to install and remove the projection lens...26 How to install the projection lens...26 How to remove the projection lens...26 How to adjust the lens...26 How to adjust the FOCUS, ZOOM and SHIFT...26 How to adjust the lens position to the left or right...27 Status function...27 Automatic adjustment (AUTO SETUP)...27 Using the SHUTTER function...27 On-screen menus...28 Structure of menu screens...28 Basic menu operations...29 Returning to the previous page...29 Menu items shown in black characters...29 Menu items setting...29 Resetting to the factory default...29 Adjusting the picture...30 PICTURE MODE...30 CONTRAST...30 BRIGHTNESS...30 COLOR...30 TINT...30 COLOR TEMP...30 WHITE GAIN...30 SYSTEM DAYLIGHT VIEW...30 SHARPNESS...31 NOISE REDUCTION...31 AI...31 SYSTEM SELECTOR...31 Adjusting the position...31 SHIFT...31 ASPECT...31 ZOOM...32 CLOCK PHASE...32 KEYSTONE...32 How to use ADVANCED MENU...32 DIGITAL CINEMA REALITY...32 BLANKING...32 INPUT RESOLUTION...33 CLAMP POSITION...33 EDGE BLENDING...33 RASTER POSITION...34 XGA MODE...34 SXGA MODE...34 Changing the display language...34 OPTION1 settings...35 COLOR MATCHING...35 Adjusting the color matching using a colorimeter...35 COLOR CORRECTION...36 CONTRAST MODE...36 AUTO SIGNAL...36 BACK COLOR...36 STARTUP LOGO...36 SUB MEMORY LIST...36 DVI EDID...37 DVI SIGNAL LEVEL...37 FUNC OSD POSITION...37 OSD MEMORY...37 OPTION2 settings...38 PROJECTOR ID...38 INSTALLATION...38 ALTITUDE...38 DIRECTION...38 LAMP SELECT...39 LAMP RELAY...39 LAMP POWER...39 RS-232C...39 SYSTEM INFORMATION...40 AUTO POWER OFF...40 DATE AND TIME...40 PASSWORD...40 Displaying the internal test pattern...40 Cycle of displayed internal test patterns...40 Setting the network...41 Returning the network function setting back to the factory setting..41 Connecting the PC...41 System requirements...41 Connection eample...41 Using Web Browser Control...42 Accessing from Web browser...42 Password change page...42 Basic control page...43 Detail control page...43 Monitor information page...44 Error information page set up page...45 Authentication server set up page...47 DNS server set up page...47 Ping test page...47 Contents of mail sent...48 Adjust clock page...48 Network config page...49 Network status page...49 Using the PJLink TM protocol...50 Supported commands...50 PJLink TM security authentication...50 Setting the security...51 PASSWORD...51 PASSWORD CHANGE...51 DISPLAY SETTING...51 TEXT CHANGE...51 CONTROL DEVICE SETUP...51 Using the serial terminals...52 Eamples of connection...52 Pin assignments and signal names...52 Communication conditions...52 Basic format...52 Control commands...53 Cable specifications...53 Using the Remote 2 terminal...53 Indication of lamp monitor...54 Cleaning and replacement of air filter...55 Procedure of cleaning...55 Replacing the lamp unit...56 When to replace the Lamp unit...56 Lamp unit replacement steps...57 Ceiling Mount Bracket Safeguards...58 Before asking for service...59 Specifications...60 Compatible Signal List...62 Dimensions...63 Installation dimensions diagram...63 Français Information...65
5 Precautions with regard to safety WARNING If you notice smoke, strange smells or noise coming from the projector, disconnect the power cord plug from the wall outlet. Do not continue to use the projector in such cases, otherwise fire or electric shocks could result. Check that no more smoke is coming out, and then contact an Authorized Service Center for repairs. Do not attempt to repair the projector yourself, as this can be dangerous. Installation work (such as ceiling suspension) should only be carried out by a qualified technician. If installation is not carried out correctly, there is the danger that injury or electric shocks may occur. Use the dedicated ceiling mount bracket specified for the model. Use the provided safety wire cable and take measures to prevent the projector from falling. Do not overload the wall outlet. If the power supply is overloaded (for eample, by using too many adapters), overheating may occur and fire may result. Do not look into the lens while the projector is being used. Strong light is emitted from the projector s lens. If you look directly into this light, it can hurt and damage your eyes. Be especially careful not to let young children look into the lens. In addition, turn off the power and disconnect the power cord plug when you are away from the projector. Never attempt to modify or disassemble the projector. High voltages can cause fire or electric shocks. For any inspection, adjustment and repair work, please contact an Authorized Service Center. Do not install this projector in a place which is not strong enough to take the full weight of the projector or on top of a surface which is unstable. If the projector is installed in a place which is not strong enough or on top of a surface which is sloped or unstable, it may fall down or tip over, and severe injury or damage could result. If foreign objects or water get inside the projector, or if the projector is dropped or the cabinet is broken, disconnect the power cord plug from the wall outlet. Continued use of the projector in this condition may result in fire or electric shocks. Contact an Authorized Service Center for repairs. Do not place liquid containers on top of the projector. Do not place the projector into water or let it become wet. If water spills onto the projector or gets inside it, fire or electric shocks could result. If any water gets inside the projector, contact an Authorized Service Center. Do not insert any foreign objects into the projector. Do not insert any metal objects or flammable objects into the projector or drop them onto the projector, as doing so can result in fire or electric shocks. Use only the power cord supplied with the projector. Do not use the supplied power cord with equipment other than the projector. Failure to observe this may result in electric shocks. Insert the power cord plug securely into the wall outlet. If the plug is not inserted correctly, electric shocks or overheating could result. Do not use plugs which are damaged or wall outlets which are coming loose from the wall. Do not do anything that might damage the power cord or the power cord plug. Do not damage the power cord, make any modifications to it, place it near any hot objects, bend it ecessively, twist it, pull it, place heavy objects on top of it or wrap it into a bundle. If the power cord is used while damaged, electric shocks, short-circuits or fire may result. Ask an Authorized Service Center to carry out any repairs to the power cord that might be necessary. Clean the power cord plug regularly to prevent it from becoming covered in dust. If dust builds up on the power cord plug, the resulting humidity can damage the insulation, which could result in fire. Pull the power cord plug out from the wall outlet and wipe it with a dry cloth. If not using the projector for an etended period of time, pull the power cord plug out from the wall outlet. Do not handle the power cord plug with wet hands. Failure to observe this may result in electric shocks. 5
6 6 Precautions with regard to safety Do not set up the projector in humid or dusty places or in places where the projector may come into contact with oily smoke or steam. Using the projector under such conditions may result in fire, electric shocks or plastic deterioration. The plastic deterioration may cause the falling down of the projector which is mounted in the ceiling. Do not place the projector on soft materials such as carpets or sponge mats. Doing so may cause the projector to overheat, which can cause burns, fire or damage to the projector. During a thunderstorm, do not touch the projector or the cable. Electric shocks can result. Do not place your hands or other objects close to the air outlet port. Heated air comes out of the air outlet port. Do not place your hands or face, or objects which cannot withstand heat close to this port [allow at least 50 cm (19.7") of space], otherwise burns or damage could result. Do not use or handle the batteries improperly. Failure to observe these precautions may cause the batteries to leak, overheat, eplode or catch fire. - Do not disassemble the dry cell batteries. - Do not heat, or disassemble the batteries or place them into fire or liquids such as water. - Do not connect the + and - terminals with wire or other metallic objects. - Do not store batteries together with metallic objects such as necklaces or hairpins. - Make sure the polarities (+ and -) are correct when inserting the batteries. - Do not use a new battery together with an old battery or mi different types of batteries. - Do not use batteries with the outer covering peeling away or removed. - Do not use rechargeable batteries in place of the dry cell batteries. - The batteries have a protective outer covering. Do not remove this covering, as this may result in a short circuit. If the battery fluid leaks, do not touch it with bare hands, and take the following measures if necessary. Battery fluid entering your eyes may result in loss of sight. In this case, do not rub your eyes. Rinse with clean water and seek medical advice immediately. Battery fluid on your skin or clothing may result in skin inflammation or injury. Rinse with clean water and seek medical advice immediately. Remove empty batteries from the remote control at once. Do not leave empty batteries inside the equipment, as this may cause the batteries to leak, overheat or eplode. Before replacing the lamp, be sure to disconnect the power cord plug from the wall outlet. Electric shocks or eplosions can result if this is not done. When replacing the lamp, allow it to cool for at least one hour before handling it. The lamp cover gets very hot, and touching it can cause burns. Do not disassemble the lamp unit. If the lamp section breaks, it may cause injury. Caution When disconnecting the power cord, hold the plug, not the cord. If the power cord itself is pulled, the cord will become damaged, and fire, short-circuits or serious electric shocks may result. Always disconnect all cables before moving the projector. Moving the projector with cables still attached can damage the cables, which could cause fire or electric shocks to occur. Do not place a projector or other heavy object on top of the unit. Do not put your weight on this projector. Failure to observe this may cause the projector to become unbalanced and fall, which could result in damage or injury. The projector may be damaged or deformed. Do not prevent heat loss. Doing so may cause the projector to overheat, which can cause fire or damage to the projector. Do not place the projector in narrow, badly ventilated places such as closets or bookshelves. Do not place the projector on cloth or papers, as these materials could be drawn into the air inlet port.
7 If the lamp has broken, ventilate the room immediately. Do not touch or bring your face close to the broken pieces. Failure to observe this may cause the user to absorb the gas which was released when the lamp broke and which contains nearly the same amount of mercury as fluorescent lamps, and the broken pieces may cause injury. If you believe that you have absorbed the gas or that the gas has got into your eyes or mouth, seek medical advice immediately. Ask your dealer about the replacement of the lamp unit and check the inside of the projector. If not using the projector for an etended period of time, disconnect the power cord plug from the mains socket. If dust builds up on the power cord plug, the resulting humidity may damage the insulation, which could result in fire. Disconnect the power cord plug from the wall outlet as a safety precaution before carrying out any cleaning. Electric shocks can result if this is not done. Be careful not to catch your fingers between the lens and shroud when shifting the lens. Do not catch your fingers between the lens and shroud when shifting the lens as it may cause injury. Ask an Authorized Service Center to clean inside the projector at least once a year. If dust is left to build up inside the projector without being cleaned out, it can result in fire or problems with operation. It is a good idea to clean the inside of the projector before the season for humid weather arrives. Ask your nearest Authorized Service Center to clean the projector when required. Please discuss with the Authorized Service Center regarding cleaning costs. If not using the projector for an etended period of time, remove the batteries from the remote control. Failure to do so may cause the batteries to leak, overheat, catch fire or eplode, possibly resulting in fire or corruption of surrounding areas. Do not use the old lamp unit. The lamp section may break. Do not place the projector in etremely hot locations. Doing so may cause the outer casing or internal components to deteriorate, or result in fire. Take particular care in locations eposed to direct sunlight or near stoves. Accessories Check that all of the accessories shown below have been included with your projector. Remote control unit [N2QAYB ] Power cord [K2CG3FZ ] Battery for remote control unit (AA) [R6DW/2ST] Lens cover [TKKL ] Wire cable [TKLA3201 1] Wire fastening M6 screw [XYN6+F10FJ 1] 7
8 Precautions on handling 8 Precautions on transport Make absolutely sure that the lens cap is in place when transporting the projector or carrying it around. Both the projector and the projection lens are precision-made and, as such, are susceptible to vibration and impacts. When transporting the projector and lens or carrying them around, place them in the boes in which they were housed at the time of purchase, and take care to keep them away from vibration and impacts. Precautions on installation Be sure to observe the following precautions when installing the product. Avoid installing the product in a place eposed to vibrations or impacts. If the projector is installed in a place where vibrations are transmitted from a source of driving power and others or mounted in a car or a vessel, vibrations or impacts may be transmitted to the product to damage the internal parts, causing failure. Install the product in a place free from vibrations and impacts. Do not move the projector while it is operating or subject it to vibration or impact. The service life of its internal motors may be shortened. Do not install the projector near highvoltage power lines or power sources. The product may be eposed to interference if it is installed in the vicinity of high-voltage electrical power lines or power sources. Do not place the projector on a vinyl sheet or carpet. If a vinyl sheet sucked up and blocks the air filter intake port, the internal temperature of the projector may increase, which triggers the protection circuit, turning off the power. Be sure to ask a specialized technician when installing the product to a ceiling. If the product is to be installed hanging from the ceiling, purchase an optional hanging attachment (for high ceiling: Model No. ET-PKD56H) (for low ceiling: Model No. ET-PKD55S). Please call a specialized technician or contact an Authorized Service Center for installation. Install the projector so that it will be supported only by its bottom panel and by none of its other parts or surfaces. Do not place the projector over m ( ') above sea level. When using it over m ( ') above sea level, set the ALTITUDE, described on page 38, to HIGH. Otherwise the life of the product may be shortened. When using it over m above sea level, consult your dealer. Lens Focus Do not adjust the lens focus in the initial period (within appro. 30 minutes) after switching the projector on. The high clarity projector lens is thermally affected by the light from the light source, making the focus unstable in the period just after switching on. Please allow a warm-up time of at least 30 minutes before adjusting the lens focus. Failure to do so may cause heating focus drift. Disposal To discard the product, call the dealer or a specialized dealer. Precautions on use To view clear images: The audience cannot enjoy high-contrast and clear images if outside light or the illumination interferes the screen surface. Draw window curtains or blinds, turn off the lightings near the screen or take other proper measures. Depending on where the projector is used, there are rare occasions when hot air from the air ehaust vents or the warm air from air conditioning can cause a shimmering effect on the screen. For this reason, take care not to shield the air ehaust vents and consider the direction of the air flowing from air conditioning. Do not touch the surface of the projection lens with bare hand. If fingerprints or stains are left on the projection lens surface, they are magnified and projected on the screen. Keep your hands away from the lens. Cover the lens with the supplied lens cap when the projector is not used. Lamp A mercury lamp with high internal pressure is used for the light source of this product. A high-pressure mercury lamp has the following characteristics: It may burst with a loud sound or end its life cycle by not illuminating because of given impacts, flaws, or deterioration due to used hours. The life cycle of a mercury lamp varies according to the individual difference or conditions of use. In particular, turning the power on and off frequently and/or repeatedly will greatly affect the life cycle. In rare cases, it may burst shortly after the first lighting. The possibility of burst increases when the lamp is used beyond the replacement time. Lamp deterioration accelerates when used continuously for 24 hours or more. Lamp deterioration due to continuous use can be reduced by using the LAMP RELAY function. Cleaning and maintenance Be sure to remove the power cord plug from the receptacle before cleaning. Use soft and dry cloth to clean the cabinet. If stains are hard to remove, use a cloth dampened with a kitchen detergent solution (neutral) and squeezed to wipe the cabinet and finish with a dry cloth. If a chemical wipe is used, follow its instructions. Do not clean the lens surface with fuzzy or dusty cloth. If dust adheres to the lens, it will be magnified and projected on the screen. Use a soft and clean cloth to wipe off dust.
9 Name and function of parts Remote control Remote control operation indicator lamp The lamp flashes when any remote control button is pressed. POWER STANDBY ( ) button (page 25) Switched the power to the standby mode if the MAIN POWER has been put to the l position. POWER ON ( I ) button (page 24) Turns on the power if the MAIN POWER has been put to the l position. Input selector (RGB1, RGB2, DVI-D, VIDEO, S-VIDEO) button Use to toggle through the RGB1, RGB2, DVI-D, VIDEO and S-VIDEO input ports. MENU button (page 29) Displays and clears the MAIN MENU. It can also return to the previous screen when the menu is displayed. Arrow buttons (page 29) Use these buttons to select an item on the menu screen, change setting and adjust the level. Also use them to enter the SECURITY password. ENTER button (page 29) Press this button to enter your menu selection or to run function. ON SCREEN button This button turns on and off the on-screen indication function. TEST PATTERN button (page 40) This displays the test pattern. Numeric (0-9) buttons (pages 15, 40) These buttons are used for systems where more than one projector is being used. They are used to enter ID numbers when selecting an ID, and they are also used by service personnel for entering passwords when password entry is needed. STATUS button (page 27) Press this button to display projector information. It can also be used to send information about the projector s status via . AUTO SETUP button (page 27) Pressing this button while projecting an image automatically corrects the picture positioning on the screen. While the auto setup feature is active, a message AUTO SETUP appears on the screen. SHUTTER button (page 27) Press this button to black out the image temporarily. ASPECT button (page 31) Switches the image aspect ratio. 9
10 Name and function of parts Bottom LENS (FOCUS, ZOOM, SHIFT) buttons (page 26) These buttons are used to adjust the projection lens. Function 1 (FUNC1) button (page 37) This button can control the functions set in FUNC1 of the OPTION1 screen from the MAIN MENU. DEFAULT button (page 29) Press this button to restore the default factory setting. ID SET button (page 15) When two or more main units are used in the system, this button specifies the ID of the remote control. ID ALL button (page 15) When two or more main units are used in the system, this button switches to the mode to control them simultaneously with a single remote control. Remote control transmitter window Operate the remote control aiming at the remote control receiver window on the main unit. Remote control wired terminal (page 15) To use the wired output terminal, connect the remote control and the main unit with the M3 stereo mini jack cable available in the market. 10
11 Front and side of the projector Side-mounted connection terminals (page 13) Status LED lights (Refer to the figure on the right.) Status LED lights AC IN terminal (page 24) Connect the supplied line power cord into this receptacle. Do not connect any other cable to this socket. Air filter (page 55) Burglar lock Attach a commercial burglar prevention cable (e.g., from Kensington) to this lock port. It is compatible with the Microsaver Security System from Kensington. Clasp for attaching anti-theft chain Attach a chain or other fastening device available from a hardware store through this clamp. Level-adjusting feet (page 24) Use these feet to adjust the tilt of the projector. (The leveling feet at the front left and right can be adjusted.) Lens release button (page 26) Press this to remove the projection lens. Projection lens Lens for projecting images on the screen. Lens left/right adjusting dial (page 27) Turn this clockwise to move the screen to the left; conversely, turn it counterclockwise to move it to the right. Remote control receiver window (front) (page 14) This window receives the signal beam emitted from the remote control. Focus ring (page 26) For focus adjustment. Powered focus adjustment is also available. Temperature monitor (TEMP) (page 54) Lighting or blinking of this lamp indicates an abnormal condition of the internal temperature. LAMP1 monitor (page 54) This lamp lights up when the time to replace lamp unit 1 is reached. It also blinks if something unusual occurs in the lamp circuit. LAMP2 monitor (page 54) This lamp lights up when the time to replace lamp unit 2 is reached. It also blinks if something unusual occurs in the lamp circuit. Power indicator (page 24) The lamp lights in red when the MAIN POWER switch is turned to l (on). It turns to green when the POWER ON button of the remote control or the main unit is pressed. Lens cap Cap the lens whenever the projector is left unused. Air intake vents Attention Do not remove the upper cover (white or black top panel). 11
12 Name and function of parts Rear view of the main unit Controls on rear panel Controls on rear panel 12 Air ehaust vents AUTO SETUP button (page 27) Pressing this button while projecting an image Do not place your hands or other objects close to the air outlet port. Heated air comes out of the air outlet port. Do not place your hands or face, or objects which cannot withstand heat close to this port [allow at least 50 cm (19.7") of space], otherwise burns or damage could result. Lamp unit cover The lamp unit is housed. MAIN POWER switch (page 24) Use this switch to turn on I and off O the main power applied to the projector. Remote control receiver window (rear) (page 14) This also receives the signal beam coming from the remote control. POWER ON ( I ) button (page 24) Turns on the power. POWER STANDBY ( ) button (page 25) Switches the power to the standby mode. RGB1 button (page 24) Switches to RGB1 input. RGB2 button (page 24) Switches to RGB2 input. VIDEO button (page 24) Switches to video input. S-VIDEO button (page 24) Switches to S-VIDEO input. MENU button (page 29) Displays and clears the MAIN MENU. It can also return to the previous screen when the menu is displayed. The on-screen display (OSD) selection menu can be displayed by holding down the menu key for at least three seconds. automatically corrects the picture positioning on the screen. DVI button (page 24) Switches to DVI-D input. SHUTTER button (page 27) Press this button to black out the image temporarily. ENTER button (page 29) Press this button to enter your menu selection or to run function. LENS button (page 26) Switches to the adjustment mode for lens focus, zoom and shift (position). Arrow ( ) buttons (page 29) Use to select an item on the menu screen, change setting and adjust the level. Also use them to enter the SECURITY password.