SYNTHEMUL Product Code: All-Acrylic Latex SEMI-COMMERCIAL
|
|
- Beatrix Henderson
- 8 years ago
- Views:
Transcription
1 APRIL 2005 SYNTHEMUL Product Code: All-Acrylic Latex SEMI-COMMERCIAL DESCRIPTION SYNTHEMUL is high-performance; ultra-low VOC acrylic latex ideal for cosolvent-free exterior house and trim paints. Performance features include alkyd-like adhesion to a variety of difficult substrates, particularly chalky surfaces and aged gloss alkyd. can be formulated at less than 20 gram/liter VOC, giving the paint formulator more latitude in meeting current and future environmental regulations. APPLICATIONS Exterior house paint: flat thru semi-gloss Exterior opaque stains Masonry paints Primers Exterior semi-transparent stains FEATURES Near zero VOC depending on additive package Low temperature film formation Exterior durability Wet adhesion: chalk and gloss alkyd Early water resistance/ reduced blistering Efflorescence resistance Zinc oxide stability Freeze/thaw and long term stability Thick films without mudcracking BENEFITS No need for glycols or coalescing solvents Long term exterior durability Minimal surface preparation required Early resistance properties to humidity and rain Improved appearance over concrete Environmentally-friendly paints Application friendly PROPERTIES Type All Acrylic Percent Solids, Weight 50 Percent Solids, Volume 47 approx. Viscosity at 25 C, Brookfield LVT, #2 at 60 rpm, cps 200 cps Pounds per Gallon, Solution 8.80 ph 8.5 Glass Transition Temperature, C 4 STORAGE Store in a cool, dry place, preferably under 80 F t o ensure a useful shelf life of at least six months. Protect from freezing. Read the Material Safety Data Sheet before handling, storing, or using this product.
2 SUGGESTED FORMULATION Pounds Gallons Raw Material Analysis: Water Weight per gallon, pounds Attagel 50 Weight solids, percent Natrosol 330 Plus Volume solids, percent AMP-95 PVC, % Igepal CTA-639W VOC, (gms/ltr) Colloid 226 KU C FoamStar A10 ICI viscosity, 25 C Minex 4 ph Imsil 1240 Silica 60 Gloss TiPure R Gloss 2.3 Disperse at high speed to 5.0 Hegman. Add grind to the following letdown: Water FoamStar A Add slowly into vortex in the order listed: Nuosept Troysan Polyphase Water Total TYPICAL PERFORMANCE DATA In-can Properties (25 C) Thick Film ph Mudcracking (37 F) KU sealed, mils 40 <14 ICI unsealed, mils 40 <14 #7 DOW - Leneta Contrast ratio Heat Age Stability (4 weeks at 60 C) % Reflectance Stormer, KU Gloss ICI, Poise Sheen ph, Low Temperature Freeze thaw Stability Film Formation (37 F) 5 cycles +8 KU Gel -1 cycle (3% phthalo blue dispersion) E (low temp. / room temp.) Mudcracking (3.5 mil) 10 4 severe 2
3 TYPICAL PERFORMANCE DATA Adhesion: Cross-hatch Abrasive Scrub Resistance 7-day Relative Scrub Resistance 194% 100% Chalk Latex (rating 4-6) Dry Adhesion 5B 5B Wet Adhesion 3B 2B Aged Gloss Alkyd Dry Adhesion 5B 5B Wet Adhesion 5B 5B Galvanized Steel Dry Adhesion 1B 1B Wet Adhesion 1B 0B Aluminum Dry Adhesion 2B 3B Wet Adhesion 2B 3B Smooth Steel Dry Adhesion 4B 4B Wet Adhesion 4B 4B 3
4 SUGGESTED FORMULATION Pounds Gallons Raw Material Analysis: Water Weight per gallon, pounds Attagel 50 Weight solids, percent Natrosol 330 Plus Volume solids, percent AMP-95 PVC, % Igepal CTA-639W VOC, (lbs/gal) Colloid 226 VOC, (gms/ltr) FoamStar A10 KU 25 C Minex 7 ICI viscsoity, 25 C TiPure R902 ph Disperse at high speed to 5.0 Hegman. 60 Gloss Add grind to the following letdown: 85 Sheen OP Water FoamStar A Add slowly into vortex in the order listed: Nuosept Troysan Polyphase Water Total TYPICAL PERFORMANCE DATA In-can Properties (25 C) Thick Film ph Mudcracking (37 F) KU sealed, mils 40 <14 ICI unsealed, mils 45 <14 #7 DOW - Leneta Heat Age Stability (60 C) Contrast ratio weeks 0 12 % Reflectance weeks gloss weeks sheen Freeze thaw Stability Low Temperature 5 cycles +11 KU gell - 2 cycles Film Formation (37 F) (3% phthalo blue dispersion) E (low temp. / room temp.) mudcracks 8 few 3 severe 4
5 TYPICAL PERFORMANCE DATA Adhesion: Cross-hatch Abrasive Scrub Resistance 7-day trial Galvanized Steel trial Dry 3B 2B average 2,170 1,576 Wet 4B 2B % of EM Aluminum Dry 3B 2B Wet 3B 4B Smooth Steel Dry 4B 4B Wet 4B 3B Aged Gloss Alkyd Dry 5B 5B Wet 5B 5B Chalk Latex (rating 4-6) Dry 4B 4B Wet 3B 2B 5
RHOPLEX AC-264 Emulsion Polymer 100% Acrylic Binder for Exterior Flat, Satin and Semigloss Architectural Coatings
RHOPLEX AC-264 Emulsion Polymer 100% Acrylic Binder for Exterior Flat, Satin and Semigloss Architectural Coatings Rhoplex AC-264 emulsion polymer is a unique high solids, 100%-acrylic emulsion vehicle
More informationfamily of products is really Reichhold s answer to the growing need to meet more stringent regulations and performance requirements.
Alkyd performance. Water cleanup. Beckosol AQ is a new platform of low VOC alkyd latex resins made from renewable resources. We take conventional alkyd chemistry and emulsify it in water to deliver a unique
More informationACRYSOL RM-7 Rheology Modifier For Waterborne Architectural and Industrial Coatings
ACRYSOL RM-7 Rheology Modifier For Waterborne Architectural and Industrial Coatings Description ACRYSOL RM-7 rheology modifier is a remarkably versatile hydrophobically modified alkali-soluble emulsion
More informationRHOPLEX HG-706 Acrylic Emulsion
RHOPLEX HG-706 Acrylic Emulsion Description Featuring New Innovative Crosslinking Technology for VOC-Compliant Aqueous Gloss and Semigloss Enamels State-of-the-art technology is the backbone of RHOPLEX
More informationRHOPLEX SG-10M 100% Acrylic Emulsion For Interior/Exterior Semigloss Latex Paints
RHOPLEX SG-10M 100% Acrylic Emulsion For Interior/Exterior Semigloss Latex Paints Description RHOPLEX SG-10M emulsion is a versatile 100% acrylic copolymer that was designed for use in high-quality interior/exterior
More informationFASTRACK 3427 Polymer Emulsion for Waterborne Traffic Marking Paints
Technical Data Sheet FASTRACK 3427 Polymer Emulsion for Waterborne Traffic Marking Paints Regional Product Availability Description North America FASTRACK 3427 Polymer Emulsion is a second generation all-acrylic
More informationSTATE OF CALIFORNIA. Department of Transportation Specification. White Tintable Finish Paint Waterborne Acrylic Latex Vehicle (Formula PWB-174A)
January 2007 STATE OF CALIFORNIA Department of Transportation Specification White Tintable Finish Paint Waterborne Acrylic Latex Vehicle (Formula PWB-174A) SCOPE This specification covers a pre-mixed waterborne
More informationAVANSE 200 Resin Waterborne Acrylic Resin for Industrial Coatings
Technical Data Sheet AVANSE 200 Resin Waterborne Acrylic Resin for Industrial Coatings Description Features and Benefits Typical Physical Properties Potential Applications AVANSE 200 Resin is an aqueous
More informationAnquawhite 100 Curing Agent
Anquawhite 100 Curing Agent Anquawhite 100 curing agent is a novel waterborne curing agent dispersion designed for use in ambient or heat cure two part epoxy systems. Anquawhite 100 curing agent can be
More informationRAPTOR TRUCK BED LINER - BLACK
4 x 750ml RAPTOR base coating x L RAPTOR hardener TECHNICAL DATA SHEET & U-POL s RAPTOR Truck Bed Liner is a durable K polyurethane coating that provides surfaces with a protective barrier. RAPTOR Tintable
More informationMARTIN TESTING LABORATORIES (MTL) PAINTS AND COATINGS TESTING CAPABILITIES
Liquid Coating Properties Composition VOC Content, ASTM D2369 Water Content, ASTM D4017 Physical Properties Calculating Physical Constants of Coatings, ASTM D5201 Density, ASTM D1475 Flash Point, ASTM
More information1045.4 High Solids Epoxy System G Intermediate Coating.
SECTION 1045 PAINT FOR STRUCTURAL STEEL 1045.1 Scope. This specification covers paint, paint material and coating systems for use on structural steel. 1045.2 Paint and Paint Material. 1045.2.1 General.
More informationSIGMAFAST 210. PRODUCT DATA SHEET December 12, 2014 (Revision of April 1, 2013) DESCRIPTION
DESCRIPTION Two-component, high-build zinc phosphate polyurethane primer/finish PRINCIPAL CHARACTERISTICS Specially designed for in-shop application Fast-curing Easy application by airless spray Unlimited
More informationRHOPLEX 2620 100% Acrylic Polymer For High Performance Clear and Colored Sealants
RHOPLEX 2620 100% Acrylic Polymer For High Performance Clear and Colored Sealants Description RHOPLEX 2620 emulsion is a high performance acrylic latex binder designed for sealants. This high solids (62%)
More informationIntercoastal Paint Company
Intercoastal Paint Company Waterborne Fast Dry Shop Primers 14029 W. Hardy Houston TX 77060 (281) 448-5258 Fax (281)448-2664 www.intercoastalpaint.com Table of Contents 1. Waterborne Shop Primers- Why
More informationHigh-Performance Coatings Resins
High-Performance Coatings Resins HYBRIDUR 570 Polymer Dispersion DESCRIPTION HYBRIDUR Polymer Dispersions are a line of anionically stabilized acrylic-urethane hybrid polymers from Air Products. These
More informationSuccessful Painting Jobs Start Here.
Successful Painting Jobs Start Here. The Right Primer Makes All the Difference. Selecting the right primer for the job is a critical part of improving paint coverage and achieving the highest quality finish
More informationMinor Cracks in Horizontal Surfaces
Cracks, chips and broken or flaking areas in concrete are not only unsightly, they can lead to further deterioration of the surface. The result is a costly replacement project as opposed to a simple repair.
More informationARDEX GUIDE SPECIFICATION ARDEX Exterior Concrete Repair & Resurfacing Polymer-Modified, Cement-Based, Patch & Horizontal Overlay Materials
ARDEX GUIDE SPECIFICATION ARDEX Exterior Concrete Repair & Resurfacing Polymer-Modified, Cement-Based, Patch & Horizontal Overlay Materials SECTION 03 92 50 PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings,
More informationDecorative Matt Emulsion Paint
Hydrous Kaolins for Decorative Matt Emulsion Paint Hydrous Kaolin Highly recommended for decorative matt emulsions PERFORMANCE MINERALS Hydrous Kaolin Increases opacity by improving TiO 2 spacing. Hydrous
More informationEXTERIOR PAINT SCHEDULE
A. CONCRETE, STUCCO, AND MASONRY (OTHER THAN CONCRETE MASONRY UNITS): 2. Flat Elastomeric Finish: *1 st Coat: McCormick Interior/Exterior Acrylic Clear Brushing Lacquer Surface Conditioner 01242 OR McCormick
More informationEclipse. Technical Data Sheet. Polyurethane topcoat. Product Group
Technical Data Sheet Product Group Polyurethane topcoat Characteristics Product Information A chemically cured, low VOC topcoat designed to provide premium gloss and distinctness of image (DOI). This coating
More informationDow Coating Materials Acrylic Binders for Waterborne Industrial Coatings
Dow Coating Materials Acrylic Binders for Waterborne Industrial Coatings Less chemical, more chemistry The Acrylic Advantage Few binder chemistries for industrial coatings match the simplicity and performance
More informationSYNTRAN Cationic Acrylic Copolymers
SYNTRAN Cationic Acrylic Copolymers For Waterborne Stain-Blocking Paints and Lacquers Exceptional Stain Blocking Performance: Nicotine Stains, Wood Extractives, Graffiti, etc. Environmentally Friendly
More informationSECTION 09900 PAINTS AND COATINGS. Display hidden notes to specifier by using "Tools"/"Options"/"View"/"Hidden Text".
A PPG Brand SECTION 09900 PAINTS AND COATINGS Display hidden notes to specifier by using "Tools"/"Options"/"View"/"Hidden Text". PART 1 GENERAL 1.1 SECTION INCLUDES A. Surface preparation and field painting
More informationPARALOID AU-1164S Hydroxyl-Functional Acrylic Polyol
PARALOID AU-1164S Hydroxyl-Functional Acrylic Polyol Paraloid AU-1164S is a hydroxyl-functional acrylic polyol designed for acrylic urethane coatings. This product replaces the solid grade form Paraloid
More informationPRODUCT DATA SHEET DESCRIPTION:
DESCRIPTION: SP-9888 Pipe Lining is based on the latest Zero VOC Novolac Technology. The product cures to a highly cross-linked coating with excellent chemical, solvent and water immersion resistance.
More informationApplication of Exterior Wood Finishes
Application of Exterior Wood Finishes The following information is excerpted from the publication, Exterior Wood in the South Selection, Applications, and Finishes by Daniel L. Cassens and William C. Feist;
More information09990 MOLD REMEDIATION, LEAD-BASED PAINT ABATEMENT AND ENCASEMENT OF ASBESTOS
09990 MOLD REMEDIATION, LEAD-BASED PAINT ABATEMENT AND ENCASEMENT OF ASBESTOS PDS SE-160 01-2006 1. PRODUCT NAME SE-160 Clear Surface Coating (water-based copolymer) Specialty Elastomeric Topcoat 2. MANUFACTURER
More informationPRODUCT DATA SHEET Sika Cable System
PRODUCT DATA SHEET Corrosion protection for bridge cables of steel and galvanized steel PRODUCT DESCRIPTION The Sika Cable System consists of coating materials as well as a sealing respectively injection
More information3 Scotch-Seal TM. Tamper Proof Sealant 1252. Technical Data Issue No. 5
3 Scotch-Seal TM Technical Data Issue No. 5 Advantages 3M Scotch-Seal is a one-part, fast drying, antitamper sealer. Self-extinguishing. It can be applied over adjustable or removable parts to indicate
More informationProperty Test/Standard Description. gloss (70-85) Flash point ISO 3679 Method 1. 212 F (100 C) calculated VOC-US/Hong Kong. US EPA method 24 (tested)
Not approved 2063;2064 1,2 2063 ^(ValidationDate) 1 Product description This is a two component solvent free polyamine cured coating. It is a general purpose tank lining with good chemical resistance.
More informationFLOOR TREATMENT 09610
14805 E. Moncrieff Place Aurora, CO 80011 Phone: (800) 872-5515 Phone: (303) 371-1411 Fax: (303) 371-6958 E-mail: gerry.mueller@bona.com www.bonakemi.com This MANU-SPEC utilizes the Construction Specifications
More informationScotch-Weld TM. Epoxy Adhesive 1838 B/A Green 1838 B/A Tan 1838-L B/A Translucent. Technical Data February, 2016. Product Description
3 Scotch-Weld TM 1838 1838 1838-L Technical Data February, 2016 Description 3M TM Scotch-Weld TM s 1838 and are controlled flow products; Scotch-Weld 1838-L is flowable. These epoxy adhesives are two-part,
More informationCompany Profile p.3. Product Coding System p.4. Saturated carboxylated polyesters for TGIC systems
P O L Y E S T E R R E S I N S F O R P O W D E R C O A T I N G S R E C L A I M I N G T H E F U T U R E Contents Company Profile p.3 Product Coding System p.4 Saturated carboxylated polyesters for PRIMID
More informationTriarch Products Over Various Interior Substrates
Triarch products work well over a variety of substrates, both for interior and exterior settings. This document will only discuss interior substrates and is not intended to be a technical discussion of
More informationHIGH TEMPERATURE PROTECTIVE COATINGS
HIGH TEMPERATURE PROTECTIVE COATINGS Technical Bulletin A6 Aremco s Corr-Paint protective coatings include the most expansive line of high temperature organic- and ceramic-based products available on the
More informationScotch-Weld. Low-Odor Acrylic Adhesives DP810 DP810 NS. Technical Data June, 2004
3 Scotch-Weld TM Technical Data June, 2004 Product Description 3M Scotch-Weld Low-Odor Acrylic Adhesive DP810 and DP810 NS are twopart, 1:1 mix ratio, toughened structural adhesives with less odor than
More informationSOCAL UP. Innovative High Performance Precipitated Calcium Carbonate for Emulsion Paints. PCC Division Solvay Special Chemicals
SOCAL UP Innovative High Performance Precipitated Calcium Carbonate for Emulsion Paints PCC Division Solvay Special Chemicals Socal UP benefits in Emulsion paints Up to 60 % TiO 2 substitution (1 : 1)
More information3 Scotch-Weld TM. Urethane Adhesives 3532 B/A 3535 B/A 3549 B/A. Technical Data March, 2002
3 Scotch-Weld TM Technical Data March, 2002 Product Description 3M TM Scotch-Weld TM 3532 B/A, 3535 B/A and 3549 B/A are two-component, polyurethane adhesives which cure at room temperature or with heat
More information10P20-44 High Solids Epoxy Primer
Technical Data Sheet Product Group High solids epoxy primer Characteristics Product Information A high solids urethane compatible, Skydrol resistant primer for the exterior of aircraft. It provides excellent
More informationAcrylic Binders for Water-borne Industrial Coatings
Dow Coating Materials Industrial Coatings Solutions Acrylic Binders for Water-borne Industrial Coatings Version January 2016 Dow Coating Materials 2 Industrial Coatings Solutions Industrial Coatings: tough
More informationMetal Wall Panels. Colorweld 300 Architectural Finishes
Metal Wall Panels Colorweld 300 Architectural Finishes Metal Wall standard architectural finishes These products are protected and colored with high-performance Colorweld 300 coatings ensuring precise
More informationProduct Information/Specifications
BARN & FENCE PAINT NO. 25 BARN RED Smooth or rough sawn exterior vertical wood surfaces such as plywood, fences, shingles, shakes, siding. laminates, masonry and stucco surfaces. AVAILABLE IN: Gallon Only
More informationSIGMACOVER 280. PRODUCT DATA SHEET December 10, 2014 (Revision of March 1, 2014) DESCRIPTION
DESCRIPTION Universal epoxy anticorrosive primer, based upon pure epoxy technology PRINCIPAL CHARACTERISTICS Universal epoxy primer system suitable for Ballast Tanks, Decks, Topside, Superstructure, Hull
More information2014 SPECIFICATION GUIDE Conveyor Equipment
1 Table of Contents Page Introduction Identifying painting requirements 3 How do I use this Specification Guide 3 Contacting my local Axalta Representative 3 Paint Selection Identifying the correct paint
More informationPHOENIX 370-120 Product Data Sheet (Updated on 14-Jan-2012) www.phoenixasia.com.hk
DESCRIPTION A water borne thin film intumescent coating for the fire protection of structural steelwork. PRODUCT FEATURES AND RECOMMENDED USES Provides up to 120 minutes fire resistance to structural steelwork.
More information- - - - Steel Panel Frame. Exterior Steel Sheeting. Optional Rigid Insulation. Optional Steel Insulation Liner
The Kelly Klosure pre-framed modular panel has 4 components that are factory finished to create an easy and versatile bolt-together system in the field. Steel Panel Frame Exterior Steel Sheeting Optional
More informationTECHNICAL DATA SHEET HAMMERITE METAL PAINT. Smooth Hammered Satin Aerosol
TECHNICAL DATA SHEET HAMMERITE METAL PAINT Smooth Hammered Satin Aerosol TENDER ITEM NO (Where applicable) Hammerite Products Ltd. ICI Paints, Wexham Road Slough, Berkshire, SL2 5DS. Telephone (01753)
More information3 Scotch-Weld TM. Urethane Adhesives 3532 B/A 3535 B/A 3549 B/A. Technical Data January, 2010
3 Scotch-Weld TM Technical Data January, 2010 Product Description 3M Scotch-Weld 3532 B/A, 3535 B/A and 3549 B/A are two-component, polyurethane adhesives which cure at room temperature or with heat to
More informationApproved. Property Test/Standard Description. matt (0-35) Flash point ISO 3679 Method 1 27 C calculated IED (2010/75/EU) (calculated)
Approved 402;2521 1 2521 zinc epoxy ^(ValidationDate). 1 Product description This is a two component polyamide cured zinc rich epoxy coating. It is a very high zinc dust containing product. It conforms
More informationRadiation Curable Components and Their use in Hard, Scratch Resistant Coating Applications
Radiation Curable Components and Their use in Hard, Scratch Resistant Coating Applications William Schaeffer Steven Tyson Indu Vappala Robert Kensicki Sartomer USA, LLC 502 Thomas Jones Way Exton, PA 19343
More informationROVACE HP-2931 High Performance Vinyl Acetate/Acrylic Copolymer Emulsion
ROVACE HP-2931 High Performance Vinyl Acetate/Acrylic Copolymer Emulsion Description ROVACE HP-2931, vinyl acetate acrylic copolymer emulsion, is designed for use in formulation high performance adhesives
More informationWater-based Polyurethane and Acrylate Dispersions. for Flexible Substrates
Water-based Polyurethane and Acrylate Dispersions for Flexible Substrates Exemption clause: The aforesaid information is based on our present state of knowledge and shall inform on our products and their
More informationA complete guide of epoxy coatings for industrial and marine applications. Epoxy Coatings Guide
A complete guide of epoxy coatings for industrial and marine applications. Epoxy Coatings Guide Epoxy coatings are generally packaged in two parts that are mixed prior to application. The two parts consist
More informationUFGS-09 96 00 (July 2007) UNIFIED FACILITIES GUIDE SPECIFICATIONS
USACE / NAVFAC / AFCEC / NASA UFGS-09 96 00 (November 2014) ----------------------------- Preparing Activity: NASA Superseding UFGS-09 96 00 (July 2007) UNIFIED FACILITIES GUIDE SPECIFICATIONS References
More informationDenco Sales Aspire Catalog
Denco Sales Aspire Catalog This catalog is a product reference guide. For more detailed information, inventory availability, pricing, data sheets, printing profiles and more click here to go to the Denco
More informationTECHNICAL DATA RS-6100. European Clear EZ. 5751 N. Webster Street Dayton, OH 45414-0802 Phone 937-890-6547 Toll Free 800-257-6547 Fax 937-890-6320
RS-6100 TECHNICAL DATA European Clear EZ DESCRIPTION: RS-6100 European Clear EZ is formulated with premium European resins. It is ideal for excellent color matching on white, light colors and metallics
More informationEXILVA, NATURAL PERFORMANCE ENHANCER IN PAINTS AND COSMETICS
EXILVA, NATURAL PERFORMANCE ENHANCER IN PAINTS AND COSMETICS Advanced chemical solutions from sustainable and renewable raw materials Outline Presentation of Borregaard Biorefinery consept Presentation
More informationLaminating Films - Heat Activated
Laminating Films - Heat Activated Print Guard UV This film features superb ultraviolet protection at low activation temperature (185º F - 195º F) and an aggressive solvent acrylic adhesive. Linerless Print
More informationThermal Adhesives Ther-O-Bond 1500
Products / Interface Materials / Adhesives Adhesives Bond 1500 Epoxy casting system for potting and encapsulation Bond 1600 Two part epoxy for bonding Bond 2000 Rapid cure acrylic adhesive bond High strength
More informationSC2000 CEMENT BONDING PROCEDURES
Pg.1 SC2000 CEMENT BONDING PROCEDURES Widely recognized as the world s finest cold vulcanizing cement REMA SC2000 is the solution to your industrial bonding problems. By using REMA UTR20 hardener with
More informationScotch-Weld TM. Acrylic Adhesives. DP8405NS Green. Product Data Sheet. Date: March 2014 Supersedes: August 2013
Scotch-Weld TM Product Data Sheet Acrylic Adhesives Date: Supersedes: August 2013 Product Description 3M TM Scotch-Weld Acrylic Adhesives are high performance, twopart acrylic adhesives that offer good
More informationHYDRAULIC ANALYSIS OF PIPE LINED WITH MADISON S 100% SOLIDS STRUCTURAL POLYURETHANE COATINGS
HYDRAULIC ANALYSIS OF PIPE LINED WITH MADISON S 100% SOLIDS STRUCTURAL POLYURETHANE COATINGS Shiwei William Guan, Ph.D. Vice President, R&D and International Business Madison Chemical Industries Inc. 490
More informationSpecifications. PermaTone, Inc. Manufacturer s Long Form Specifications Interior Finish Coatings PF-405
PermaTone, Inc. Manufacturer s Long Form PF-405 PART I GENERAL 1.01 SUMMARY This document provides requirements for the proper specification, design, use and installations of PermaTone specialty interior
More informationGRIP-GARD BC BASECOAT CHROME
Description Grip-Gard BC Basecoat Chrome is designed specifically to meet the color, application and quality demands of the Sign and Exhibit Manufacturer. Grip-Gard BC Basecoat Chrome is ideal for fast
More informationBasic Properties and Application of Auto Enamels
Basic Properties and Application of Auto Enamels Composition of Ceramic Automotive Glass Enamels Ceramic automotive glass colours are glass enamels that fire on to the glass during the bending process
More informationTechnical Data Sheet February 2014
Scotch-Weld Technical Data Sheet February 2014 Product Description s are high performance, two-part acrylic adhesives that offer excellent shear, peel, and impact performance. These toughened products
More informationHARD SURFACE PAPERS INSTRUCTION GUIDE
HARD SURFACE PAPERS INSTRUCTION GUIDE I Contents Page Paropy...2 Paropy I...3 Paropy...4 Acrylic...5 Cardboard Puzzles...6 Ceramic Mugs...7 Ceramic Tiles...9 Crystal...10 Glass...10 Leather...11 Magnets...11
More informationAcrylic Enamel Topcoat
Acrylic Enamel Topcoat ACRYL-GLO TECHNICAL DATA SHEET The ACRYL-GLO single-stage acrylic enamel paint system provides a durable finish that is easy to apply and suitable for both commercial and passenger
More information3.8 HSP (High Solids Polyurethane)
Description is a single-stage topcoat designed for commercial and automotive refinishing. This product provides Superior UV durability as well as commercial grade chemical resistance. 3.8 HSP has excellent
More informationAcrylic Coatings: The Perfect Stucco Finish
Acrylic Coatings: The Perfect Stucco Finish By Larry Miller and Joe Miller Whether a stucco surface is new or old, there are many different finish coatings in today s marketplace that are supposedly right
More informationTractor Painting Tips
Keeping your tractor or equipment well kept & free from rust & corrosion will extend the life of your investment & help retain its value for a longer period of time. It can be difficult, in many cases,
More informationPrimer-Sealers Solutions
Guide to Primer-Sealers Solutions for interior and exterior use Create a ready-to-paint surface, while sealing in odors and stains, and ensure the durability, appearance and success of your job. Why Prime-Seal
More informationTable of Contents. Benefits of UNIFLEX Fluid Applied Roofing Systems 2 3. Elastomeric Finish Coats 4 5. Aluminum Finish Coats 6
PORTFOLIO Table of Contents Benefits of UNIFLEX Fluid Applied Roofing Systems 2 3 Elastomeric Finish Coats 4 5 Aluminum Finish Coats 6 Asphalt Emulsion Coatings 7 Base Coats & Primers 8 9 Patch & Repair:
More informationN.V.S.C. INDUSTRIAL PRODUCTS NVSC INDUSTRIAL COATINGS THIS DOCUMENT SHOWS ALL THE N.V.S.C. PRODUCTS SUITABLE FOR INDSUTRIAL PURPOSE
Page 1 NVSC INDUSTRIAL COATINGS THIS DOCUMENT SHOWS ALL THE N.V.S.C. PRODUCTS SUITABLE FOR INDSUTRIAL PURPOSE ADDITIONAL INFORMATION CAN BE AVAILABLE DIRECTLY ON N.V.S.C. WEBSITE www.nvsc.it Page 2 INDEX
More informationSIGMACOVER 300. PRODUCT DATA SHEET December 12, 2014 (Revision of November 1, 2013) DESCRIPTION
DESCRIPTION Two-component, high-build, polyamine adduct-cured, coal tar epoxy coating PRINCIPAL CHARACTERISTICS Outstanding (sea)water resistance (outside hull and ballast tanks) Outstanding water- and
More informationSpecifications For Manufactured Materials
SMM 1301-1 Specifications For Manufactured Materials 1. SCOPE This specification covers the requirements for white and yellow fast dry alkyd traffic paint, suitable for airless and air atomized spray application
More informationDow Corning PROPRIETARY. Dow Corning. A Thermal Modelling Comparison of Typical Curtain Wall Systems
Dow Corning A Thermal Modelling Comparison of Typical Curtain Wall Systems Introduction Today s Aim To understand the meaning of a U value and window energy ratings Discuss the drivers for energy efficiency
More informationTIGER Drylac U.S.A., Inc. 3855 Swenson Avenue St Charles, IL T 800 243 8148 F 877 926 8148 office.us@tiger-coatings.us www.tiger-coatings.
Product Data Sheet SERIES 69 - DRYZINC ZINC-RICH PRIMER (69/90500) Epoxy zinc-rich powder coating primer. Part of a two-coat TIGER Shield system. Designed to impart superior corrosion protection to steel
More information( II ) INDUSTRIAL & PROTECTIVE SYSTEM
( II ) INDUSTRIAL & PROTECTIVE SYSTEM (A) ALKYD BASE QUICK PAINT AUTO GLOSS PAINT GLOSS PAINT VARNISH TOP WOOD VARNISH ALUMINUM TOP RED OXIDE ZINC CHROMATE PRIMER RED OXIDE PRIMER AUTO GLOSS ZINC CHROMATE
More information3M Scotch-Weld Epoxy Adhesive
3 Scotch-Weld TM Technical Data April, 2016 Product Description s DP100 and DP100NS are two-part adhesives offering fast cure and machinability. Available in larger containers like s 100 B/A or 100 NS
More informationACRYLICS. The properties of the resulting acrylics vary depending on the nature of the alkyl groups both on the alcohol and the acrylic acid.
AYLIS Acrylics are polyesters based on acrylic acid (propenoic acid - H 2 =H 2 H) formed from the polymerisation of an alkyl acrylate ester. They are widely used in the surface coatings industry (e.g.
More informationSECTION 03 35 43 POLISHED CONCRETE FINISHING
SECTION 03 35 43 POLISHED CONCRETE FINISHING PART 1 - GENERAL 1.01 SUMMARY A. Provide polished concrete finishing system where indicated on drawings, complete. This section includes the following: 1. Concrete
More informationHow to repair your existing low slope flat roof.
How to repair your existing low slope flat roof. Recycled Rubber Roofing is not a "Roof Coating." It is a liquid emulsion used as the underlayment of a new or retrofit, built-up roofing system. One of
More informationScotch-Weld. Epoxy Adhesives DP-100 Clear DP-100 NS Translucent. Technical Data June, 2002
3 TM Epoxy s Technical Data June, 2002 Product Description 3M Epoxy s DP-100 and DP-100NS are two-part adhesives offering fast cure and machinability. Available in larger containers like 3M Epoxy s 100
More informationGeneral Surface Preparation
General Surface Preparation Proper surface preparation will contribute significantly to the longevity of Ace Paint products. Follow these general guidelines for best results. CLEAN: Paint will not adhere
More informationImportant Notes Color
Important Notes Color Introduction A definition for color (MPI Glossary) The selective reflection of light waves in the visible spectrum. Materials that show specific absorption of light will appear the
More informationYou have just purchased the most portable and economical spray chrome system in the world!
You have just purchased the most portable and economical spray chrome system in the world! The Chrome FX Gun comes attached directly to the pots making it extremely mobile and capable of performing on
More informationDuPont ChromaOne Acrylic Urethane Single Stage
cdupont Automotive Finishes ChromaSystem Technical Manual Description ChromaOne is a productive acrylic urethane designed for spot, panel and overall repairs of OEM Single Stage finishes, both solids and
More informationBLACK JACK ALL WEATHER ROOF COATING
PAGE: 1 of 6 PRINT DATE: 16/09/2004 BLACK JACK ALL WEATHER ROOF COATING DESCRIPTION BLACK JACK ALL WEATHER ROOF COATING is a solvent based, full bodied black brushable compound with added fibres for reinforcement.
More informationScotch-Weld. Epoxy Adhesive. DP190 Translucent and Gray. Technical Data April, 2010
3 TM Technical Data April, 2010 Product Description 3M Epoxy Adhesive is a 1:1 mix ratio similar to 3M Epoxy Adhesive 2216 B/A Translucent but faster curing. 3M Epoxy Adhesive is a 1:1 by volume mix ratio
More informationHow To Test A Base Axe
Scotch-Weld DP760 Product Data Sheet Updated : February 2009 Supersedes: June 2001 Product Description DP760 epoxy adhesive is a non-sag, two-part room temperature curing adhesive designed for use when
More informationTechnical Data Sheet L1.05.03 Top coats. Mat Clear
Description Lesonal Mat clear provides a matt appearance over Lesonal Basecoat SB or may be intermixed with other suitable Lesonal clears to provide various gloss levels, for the protection and durability
More informationENVIRONMENTAL EFFECTS ON COATINGS
ENVIRONMENTAL EFFECTS ON COATINGS Surfaces exposed to the environment, may be damaged by elements such as water, snow, ice, heat, dirt, smog, humidity, brake dust, grime, salts, chemical attack, and acid
More informationPOLYURETHANE LINING AND COATING ON PIPE RAW WATER
POLYURETHANE LINING AND COATING ON PIPE RAW WATER PART 1 -- GENERAL 1.1 THE REQUIREMENT A. The CONTRACTOR shall provide pipe coating, complete and in place, in accordance with the Contract Documents. 1.2
More informationT R A N S F E R A B L E F U L LY
HSTOPS A WALL OF WATER 22 FT. HIG! F U L LY T R A N S F E R A B L E RESISTS10 PSI ! 1 F U L LY T R A N S F E R A B L E HSTOPS A WALL OF WATER 22 FT. HIG RESISTS10 PSI Guaranteed To Stop Water Even Under
More informationImron 1.2 HG High Gloss Waterborne Polyurethane (WG Quality)
Imron 1.2 HG High Gloss Waterborne Polyurethane (WG Quality) GENERAL DESCRIPTION An isocyanate-free, high gloss, single component, VOC conforming (1.2 lbs/gal), zero HAPs coating based on unique Axalta
More informationDRYTAC LARGE FORMAT GRAPHICS EASY REFERENCE GUIDE
DRYTAC LARGE FORMAT GRAPHICS EASY REFERENCE GUIDE LARGE FORMAT GRAPHICS EASY REFERENCE GUIDE ANTALIS OFFER AN EXTENSIVE DRYTAC RANGE OF LARGE FORMAT DISPLAY MATERIALS: LAMINATES, MOUNT FILM & NEW SPECIALIST
More informationA. Work on this project shall consist of, but is not limited to, the following:
PART 1 - GENERAL CLEANING AND RESTORATION OF SECTION 05900-1 1.1 SUMMARY A. Work on this project shall consist of, but is not limited to, the following: 1. Clean and treat all exposed anodized architectural
More information