Smoking and any food or drinks are not permitted in the Applications Lab!
|
|
- Evangeline Curtis
- 8 years ago
- Views:
Transcription
1 220 Lab C Introduction to Cisco IP Telephony Pre-Lab Activities: None Purpose of the experiment: To explore the Cisco IP Telephony System configuration options, and its use. Smoking and any food or drinks are not permitted in the Applications Lab! Equipment: The heart of a Cisco telephony system is a device called Cisco Unified 500 Series. This device is located in the middle of the rack in your work area. (In the past Cisco used the Call Manager and Call Unity servers, these might be in the same rack but you will not be using them. You will use several Cisco phones, Arthur (7961 series), Zaphod (7941 series) and Marvin (7961 series), and an extra phone that you will configure during the lab. You will also call an extension number connected to the Norstar system (located next to the IDF panels in the lab). You ll use a client computer for two purposes: 1. Use a web browser to configure the system. 2. To monitor the network traffic generated by calls in and out of the extension called Zaphod. Acquiring Data At the end of these instructions, you will find a sheet with several labeled sections. Use this sheet to record data as you take measurements. The lab instructor may want to sign with his initials the data sheet before you leave the lab. You must include the data sheet with your lab report to receive full credit. Steps to be Performed: Using the Cisco Phone In this part you will make several phone calls. You should actually talk some on each call. Listen for delay, noise, echo, or any other audio problems. Note the steps needed to invoke various call handling steps. Make an internal call between two Cisco phones. To do this just lift up a handset and dial one of the other two phones. The extension numbers are: Marvin: 8001, Arthur 8002 and Zaphod To answer a phone that is ringing you might need to lift the handset and select answer by pressing one of the buttons adjacent to the lower part of the phone s screen. Call an outside phone from a Cisco phone dial 9, then A phone on the Norstar side will ring. Place calls from an outside Norstar phone to Marvin (8001) and then transfer that call to another station. To do this, from a Norstar phone dial 8 and then Marvin s extension. Answer Marvin s phone and press the transfer button, wait for dial tone and dial either Arthur s or Zaphod s extension Answer the phone that is ringing ITS Printed 9/28/09
2 Press Transfer on Marvin s phone When done, hang up all phones Have Marvin answer an inbound call, then place the call on hold, call Arthur, then return to the original call. To do this, from a Norstar phone dial 8 and then Marvin s extension number Answer Marvin s phone and press the hold button Press New Call Dial Arthur s extension Answer Arthur s phone, now Marvin and Arthur are connected while the first call is on hold Hang up Arthur s phone and return to the original call by pressing resume on Marvin s phone Make a call between any two Cisco phones. Once you re actually talking, unplug one of the phones from the Cisco Unified 500. What happens? Now reconnect the phone, approximately how long does it take to get phone ready for calls again? On Marvin s phone, press the settings button. Look around this menu. Change her ring tone. Record the phone s IP and MAC addresses (under Network Configuration). Exit settings. On Marvin s phone, press the directories button. Look at the list of missed calls. Note the time and originator of the most recent unanswered call prior to the beginning of the lab period. Cisco Unified 500 On the PC screen bring up the window for Cisco Configuration Assistant application. (It is already running and logged in). Press the Topology button (located on the top toolbar, looks like a star with a yellow core) Right click Zaphod, select Properties and note its IP and MAC addresses. Repeat the process for the all other phones and the UC520. Copy the topology and this information to your data sheet. Adding a phone. Plug in the 7940 phone that is on top of the UC520 rack, connecting the black cable to the port labeled Power over Ethernet Act 3 Lnk. Wait for the phone to boot up and try using it to send and receive calls. It will be automatically assigned extension number Don t Panic! (Startup for a new phone may take a considerable amount of time to automatically configure itself). Go to the Cisco Configuration Assistant, close the Topology window if it is open and then reopen the Topology window, you should be able to see the new phone. Under Configure->Telephony->Voice select the User Extensions tab. You should be able to see the new phone, it has not been assigned a user s first, last names or User ID. Assign Trillian both to the first and last names. Assign Trillian to the UserId and as the password Click the Apply button, the configuration will be sent to the phone Adding the intercom option. You are going to configure Arthur to have intercom access to Trillian. Go to the Cisco Configuration Assistant Screen If you are not already under Configure->Telephony->Voice (User Extensions tab), go there and click on Arthur. On the bottom part of the screen you can modify the behavior of Arthur s 6 buttons (the ones to the right of Arthur s screen) Change one of Arthur s buttons to Type Intercom to call Trillian s Extension. You can label it Trillian Intercom. The system will also ask you to select which button on Trillian s phone the Intercom will appear. After a few seconds both Arthur s and Trillian s phones will have the Intercom option enabled ITS Printed 9/28/09
3 through one of their buttons. Use Arthur to have access to Trillian s speaker by pressing the Intercom button. Removing the intercom option. Select Arthur s phone under the Configure->Telephony->Voice screen (User Extensions tab) Select the button used for intercom on the bottom part of the screen and change its type to None Apply the configuration. You will notice that both Arthur s and Trillian s screens have been updated and no longer show the Intercom option. Removing a phone Unplug Trillian s phone from the UC520, remember this is the new phone you just added and is on the UC520 rack. Select Trillian s phone under the Configure->Telephony->Voice screen (User Extensions tab) and click Delete Phone Creating a Hunt Group In the Cisco Configuration Assistant close the Voice window if it is still open Go to Configure->Telephony->Phone Groups->Hunt Groups We are going to put Arthur and Zaphod in a hunt group. Whenever someone calls a particular number we are about to define, first Arthur s phone should ring then if there is no answer Zaphod s phone should ring. In the Hunt Groups windows enable the first line (which has the Pilot #1 set to 5001). On the bottom part of the screen select Arthur from the Available list and move it to the Selected list using the Add button. Do the same for Zaphod. Click apply From Marvin call the pilot number Arthur s phone should ring, let it ring for a few seconds. After that Zaphod s phone will ring. Go back to the Cisco Configuration Assistant software and disable hunt group 1 and click Apply. Traffic Analysis of an ongoing call You will be analyzing the traffic generated by the Cisco phones. To do so you will be using the Wireshark software installed on the computer you have been working on. You will capture traffic sent and received between extensions 8003 and Launch Wireshark by clicking on its icon on the desktop (The Wireshark window might appear on the television on your left, if necessary turn on the TV, hit the tv/video button until you see the computer screen, grab the window and drag it to your monitor). Go to the Capture pull down menu and click on Interfaces, the Capture Intefaces window will appear Click on the Start button for the 3 Com Etherlink PCI line in the Capture Options window If Wireshark had a capture already in memory it is going to ask you if you want to save it, answer Continue Without Saving The Capture window will appear From extension 8001 call 8003 After you answer the ringing phone you will start seeing new captured packets on the screen going to and from Zaphod s and Marvin s phone While the capture list is being updated, enter a new filter in the Filter textbox (located under the main toolbar). Enter ip.src == ZaphodsIPAddress and hit Enter. (Instead of ZaphodsIPAddress you need to type the actual IP address you recorded in your topology, it should look something ITS Printed 9/28/09
4 like some number). You just created a Wireshark filter (you can check the syntax of your filter by inspecting the text box under the main toolbar). Copy the filter text you just created by highlighting it and pressing CTRL-C. You are now capturing just the traffic coming from one of the phones. To graphically visualize the traffic generated by one of the phones (the one selected in the filter), select Statistics from the pull down menu. Then select IO Graphs, you should now see a real time graphic of the traffic flowing through your filter Click on the Filter for Graph 1, the Display Filter IO-Stat Window appears. Paste the contents of the clipboard (the filter syntax) in the Filter String textbox by pressing CTRL-V and then hit Enter. Adjust the units of the picture by setting the Y Axis Unit to Bits/Tick. (Keep the scale to Auto). Make sure the X Axis unit is set to a Tick interval of 1 second. Let the graph run for about 60 seconds and notice the long term average bits per tick (Each tick represents one second). Write this value on your data sheet; obtain this value by reading it not from the latest sample but from samples taken 30 seconds ago. Hang up the phones, you should see the line on the graphic drop to zero Close the Wireshark IO Graphs window From the list packets on the screen write down the time between two packets in milliseconds and write it on your Data Sheet. You ll do this by analyzing the time column between two consecutive packets. (Notice that each packet includes some Time information too, make sure you read the time stamps from the time column and compute the difference between any consecutive two packets from your phone call) Under the Capture pull down menu select Stop Double click on a packet shown on the screen, the details about this packet will open in a new window. Maximize this window Write down the total length in bytes of the packet, this should appear in the summary line of the packet (Example: Frame 359 (xxx bytes on wire)). You are now going to determine all the pieces that make up this packet and their lengths. These are already partially identified in your data sheet. Complete the rest of the information from the table in your data sheet. You can determine how many bytes each section occupies by clicking it on Wireshark and then counting the number of bytes represented on the bottom of the screen in hexadecimal or ASCII format. (Note that each pair of numbers in hexadecimal format represents 1 byte). To better understand how to count bytes, the Ethernet and 802.1Q fields have already been completed for you. Use these to understand how to determine the remaining values using Wireshark. Leave the system as is. ITS Printed 9/28/09
5 Requirements for your lab report General Rules Your report must be typed, except that drawings may be made by hand. While your raw data sheet must be attached, all relevant data must be copied into your typed report. Do not put things like see data sheet into your typed report. Things to put into your lab report A header section with your name, your teammates names, group number, and date/time of the lab. The initialed raw data sheet (always attach this at the end of the report) Each of the subsections below requires a brief description of what you measured, your results, and when requested a reference to and a quote from a reference source that you can compare your measurement to (for example, one of our readings or an internet source). 1. Topology view of the system with all the information you wrote down in your data sheet 2. What is the load in bits per second you recorded using the IO Graph? 3. What is the time between packets you recorded using the packet trace from Wireshark? 4. What is the packet size in bytes of each packet a phone transmits? 5. What is the packet size in bits of each packet a phone transmits? 6. Divide the packet size in bits by the time between packets in seconds, how does this compare to the value from the IO Graph? 7. The RTP section of the packet actually includes voice samples; Wireshark does not report this. Using an external reference indicate how big is a typical RTP header in bytes? 8. Using the answer above, compute the number of bytes used by the voice samples. 9. Using the answer above, compute the voice rate by converting the answer above to bits and dividing it by the time between packets. Show your result. 10. The phones in your setup used the G.711 PCMU codec (usually called simply G.711). Using an external reference look for the data rate of a G.711 codec that generates packets every 20 ms. ITS Printed 9/28/09
6 ITS 220 Lab C Data Sheet Name: Group: Group Number: Date/Time: Comment on the overall voice quality of the system What happens to a call if a phone is disconnected while on a call? How much time (approx.) does it take to boot up a phone? Draw a picture showing the topology (similar to the one shown in the Topology window) including IP addresses, MAC addresses, extensions and device names ITS Printed 9/28/09
7 Traffic analysis: (the phones are preconfigured to use a G.711 voice codec) Bits per second (read from the Wireshark figure) Time between packets generated by extension 8003 or 8001 in seconds: Total number of bytes in a packet: Packet composition Ethernet II length in bytes: Q Virtual LAN length in bytes: 4 Internet Protocol length in bytes : User Datagram Protocol length in bytes: Real-Time Transport Protocol length in bytes: Total number of bytes (add all of the above you should get the same value as the total number of bytes in a packet you wrote above): ITS Printed 9/28/09
CS 326e F2002 Lab 1. Basic Network Setup & Ethereal Time: 2 hrs
CS 326e F2002 Lab 1. Basic Network Setup & Ethereal Time: 2 hrs Tasks: 1 (10 min) Verify that TCP/IP is installed on each of the computers 2 (10 min) Connect the computers together via a switch 3 (10 min)
More informationInSciTek Microsystems 635 Cross Keys Park Fairport, NY 14450 585-421-3850. Setting up Your Phones
InSciTek Microsystems 635 Cross Keys Park Fairport, NY 14450 585-421-3850 Setting up Your Phones Table of Contents Setting up Your Phones... 1 How to Add an Analog Handset... 2 How to Add a SIP Handset...
More informationIf you need additional assistance please contact our Technical Support Center at 24 hours a day, 7 days a week.
Cisco SPA 2100 Phone Adapter Installation Manual Index Installation of the Cisco SPA 2100 Phone Adapter to NationPhone P. 1 Index, before you begin, and what is included P.2 Installing the NationPhone
More informationQuick & Easy Set-Up of Packet8 Internet Phone Service
For the Way You Live & Work Quick & Easy Set-Up of Packet8 Internet Phone Service Welcome to Packet8 Internet Phone Service. Soon, you ll be able to make all your calls over the Internet and save a bundle
More informationDNS (Domain Name System) is the system & protocol that translates domain names to IP addresses.
Lab Exercise DNS Objective DNS (Domain Name System) is the system & protocol that translates domain names to IP addresses. Step 1: Analyse the supplied DNS Trace Here we examine the supplied trace of a
More informationPersonal Call Manager User Guide. BCM Business Communications Manager
Personal Call Manager User Guide BCM Business Communications Manager Document Status: Standard Document Version: 04.01 Document Number: NN40010-104 Date: August 2008 Copyright Nortel Networks 2005 2008
More informationIpiphony Phone System. User Manual. 1 P a g e
Ipiphony Phone System User Manual 1 P a g e About this Guide This guide explains how to use the basic features of your new Aastra phones. Not all features listed are available by default. Contact your
More informationLab - Using Wireshark to View Network Traffic
Topology Objectives Part 1: (Optional) Download and Install Wireshark Part 2: Capture and Analyze Local ICMP Data in Wireshark Start and stop data capture of ping traffic to local hosts. Locate the IP
More informationIP/SIP Trunk Software User Guide
PRILINK http://www.prilink.com Tel: 905-882-4488 1-866-261-0649 Fax: 905-597-1139 Sales@prilink.com Support@prilink.com IP/SIP Trunk Software User Guide Table of Contents Overview...3 Getting Started...4
More informationQuick Start Guide. Vonage Device Motorola VT2142
Quick Start Guide Vonage Device Motorola VT2142 Before you begin 1. If you purchased your Vonage Device from a retail store, you must first activate your Vonage phone service. (You will need to provide
More informationHow To Program A Talkswitch Phone On A Cell Phone On An Ip Phone On Your Ip Phone (For A Sim Sim) On A Pc Or Ip Phone For A Sim Phone On Iphone Or Ipro (For An Ipro) On
TALKSWITCH DOCUMENTATION ADDING IP PHONES TO TALKSWITCH RELEASE 6.50 CT.TS005.008104 ANSWERS WITH INTELLIGENCE COPYRIGHT INFORMATION Copyright 2011 Fortinet, Inc. All rights reserved. Fortinet, FortiGate,
More informationZed One Hosted VoIP Telephony User Guide. A document to provide end user guidance on enterprise-class Hosted VoIP Telephony solution.
Zed One Hosted VoIP Telephony User Guide A document to provide end user guidance on enterprise-class Hosted VoIP Telephony solution. Contents Unity Desktop Client Quick Start User Guide... 3 Broadworks
More information4m. MONITORING OF ETHERNET/IP NETWORK TRAFFIC.
4m. MONITORING OF ETHERNET/IP NETWORK TRAFFIC. Wireshark (see Section 6) is a network packet analyser. It is used to: troubleshoot network problems, examine security problems, debug protocol implementations,
More informationCapture and analysis of the network traffic with Wireshark
Capture and analysis of the network traffic with Wireshark Lab Objectives Understanding the purpose of Wireshark Studying configuration settings and capture options of Wireshark Studying Wireshark filters
More informationQuick Start Guide. Vonage VWR Device
Quick Start Guide Vonage VWR Device Before you begin 1. If you purchased your Vonage Device from a retail store, you must first activate your Vonage phone service. (You will need to provide the MAC ID
More informationShoreTel Contact Center Using ShoreWare Agent Toolbar
ShoreTel Contact Center Using ShoreWare Agent Toolbar USER GUIDES RELEASE 6 Document and Software Copyrights Copyright 1998 2010 ShoreTel, Inc. All rights reserved. Printed in the United States of America.
More informationsilhouette Cloud-Based Phone System Mitel IP Phone User Reference Guide Release 5.0 Final
silhouette Cloud-Based Phone System Mitel IP Phone User Reference Guide Release 5.0 Final Contents Introduction...1 Setting your language...1 Setting your language for the web interface...1 Setting your
More informationTroubleshooting Tools to Diagnose or Report a Problem February 23, 2012
Troubleshooting Tools to Diagnose or Report a Problem February 23, 2012 Proprietary 2012 Media5 Corporation Scope of this Document This Technical Bulletin aims to inform the reader on the troubleshooting
More informationAdministration. Avaya Business Communications Manager Find Me/Follow Me. Introduction. Find Me/Follow Me Fundamentals
Avaya Business Communications Manager Find Me/Follow Me Administration Introduction Find Me/Follow Me allows simultaneous ringing on up to five different external destinations. Users and administrators
More informationHow To Use An Ip Phone On A Cell Phone On An Ipphone On A Sim Sim Sim (Cisco) Or Ip Phone (Ip Phone) On A Iphone Or Ipphone (Ipphone) On An Iphon Or Ip
USER GUIDE Cisco Small Business SPA 300 Series IP Phones Models 301 and 303 Contents Chapter 1: Getting Started 6 About This Document 6 Overview of the Cisco Small Business 300 Series IP Phones 8 Caring
More informationSIP-T22P User s Guide
SIP-T22P User s Guide Thank you for choosing this T-22 Enterprise IP Phone. This phone is especially designed for active users in the office environment. It features fashionable and sleek design, and abundant
More informationCisco 7941 / 7961 IP Phone User Guide
Cisco 7941 / 7961 IP Phone User Guide Emergency To dial 911 for emergency service, you must dial the Outside Access Digit first (usually 9) + 911. Customer Service / Technical Support (919) 459-2300, option
More informationOrchestra Call Centre Agent Software Version 3
Orchestra Call Centre Agent Software Version 3 User Guide v1.0 (Installation & Configuration) Converged Solutions Pte Ltd 1 Table of Contents Installation and Setup for Orchestra AgentIV... 3 Answering
More informationCisco Unified Communications Manager 5.1 SIP Configuration Guide
Valcom Session Initiation Protocol (SIP) VIP devices are compatible with Cisco Unified Communications Manager (formerly Cisco Unified CallManager) (SIP enabled versions). The Valcom device is added to
More informationP160S SIP Phone Quick User Guide
P160S SIP Phone Quick User Guide Version 2.2 TABLE OF CONTENTS 1.0 INTRODUCTION... 1 2.0 PACKAGE CONTENT... 1 3.0 LIST OF FIGURES... 2 4.0 SUMMARY OF KEY FUNCTIONS... 3 5.0 CONNECTING THE IP PHONE... 4
More information6.0. Getting Started Guide
6.0 Getting Started Guide Netmon Getting Started Guide 2 Contents Contents... 2 Appliance Installation... 3 IP Address Assignment (Optional)... 3 Logging In For the First Time... 5 Initial Setup... 6 License
More information2 Session buttons. 1 Phone Screen
1 Phone Screen 2 Session buttons Shows information about your phone, including directory number (extension), call information (for example caller ID, icons for an active call or call on hold) and available
More informationFax Messages. You can double click a new message to show it on your computer or a right click on it will bring up more options as follows:
Fax Messages If you have the Open Scape Fax Server installed you will be receiving faxes to your myportal. This tab shows you the fax messages you have received, the number you have received them from
More informationDialplate Receptionist Console Version 3.0.0.3
En Dialplate Receptionist Console Version 3.0.0.3 Configuration Manual TABLE OF CONTENTS Table of contents... 2 Accessing configuration panel... 2 General panel... 4 Account list... 4 Tabs... 5 Behaviour...
More informationCenturyLink Smart IP Hosted Voice and Data
CenturyLink Smart IP Hosted Voice and Data Hosted Voice End User Guide Document ID VPM 549 0001 1 TABLE OF CONTENTS 1. Introduction... 7 2. Advanced Phone Features... 8 2.1 Call Forwarding... 8 2.2 Speed
More informationVerizon Collaboration Plug-In for Microsoft Outlook User Guide
Verizon Collaboration Plug-In for Microsoft Outlook User Guide Version 4.11 Last Updated: July 2011 2011 Verizon. All Rights Reserved. The Verizon and Verizon Business names and logos and all other names,
More informationWelcome. Unleash Your Phone
User Manual Welcome Unleash Your Phone For assistance with installation or troubleshooting common problems, please refer to this User Manual or Quick Installation Guide. Please visit www.vonage.com/vta
More informationNEC s SonicView IP Recorder Release Notes. Version 1.2. Release Notes
Version 1.2 Release Notes 1 SonicView 1.2 features: Selective Recording (rules based) The user can specify extension based recording rules and orchestrate call recordings based on the enterprise requirements
More informationCisco IP Phone Training 8/26/15
Cisco IP Phone Training 8/26/15 Using your Phone This document will provide information on the following: Introduce you to your phone Place, transfer, forward, park and pick up a call Set voice mail passwords
More informationBusiness Wireless Internet quick install guide
Read me first Business Wireless Internet quick install guide Wi-Fi and email set-up instructions included Actiontec Wireless Gateway TELUS Internet account information Record your personal account information
More informationHosted PBX. TelePacific Communicator User Guide. Desktop Edition
Hosted PBX TelePacific Communicator User Guide Desktop Edition 11/19/2014 CONTENTS Login... 2 Home Window... 3 Status Flag... 4 My Room... 6 Contacts Screen... 6 History... 8 Directory... 9 Dialpad...
More informationFonality. Optimum Business Trunking and the Fonality Trixbox Pro IP PBX Standard Edition V4.1.2- p13 Configuration Guide
Fonality Optimum Business Trunking and the Fonality Trixbox Pro IP PBX Standard Edition V4.1.2- p13 Configuration Guide Fonality Table of Contents 1. Overview 2. SIP Trunk Adaptor Set-up Instructions 3.
More informationUC-One. Epik. UC-One Quick Guide. Quick Guide For Apps. Why we love UC-One
Quick Guide For Apps Epik UC-One UC-One is part of our Epik suite enabling you to access all your communication services, telephony, video, IM and presence from any supported device. Contact Integration
More informationIridium Extreme TM Satellite Phone. Data Services Manual
Iridium Extreme TM Satellite Phone Data Services Manual Table of Contents 1 OVERVIEW... 1 2 HOW IT WORKS... 1 3 BEFORE INSTALLING... 2 4 USB DRIVER INSTALLATION... 3 5 MODEM INSTALLATION AND CONFIGURATION...
More informationUSER GUIDE Cisco Small Business
USER GUIDE Cisco Small Business SPA 300 Series IP Phones Models 301 and 303 August 2013 Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other
More informationFeatures Phone Access... 1. Features Web Access... 3. emta Quick Reference Guide...14. Troubleshooting...15. Quick Reference Guide...
Phone TABLE OF CONTENTS Features Phone Access... 1 Features Web Access... 3 emta Quick Reference Guide...14 Troubleshooting...15 Quick Reference Guide...16 Features Phone Access Caller ID Feature that
More informationVerizon Collaboration Plug-In for Microsoft Outlook User Guide
Verizon Collaboration Plug-In for Microsoft Outlook User Guide Version 4.11 Last Updated: July 2011 2011 Verizon. All Rights Reserved. The Verizon and Verizon Business names and logos and all other names,
More informationOfficeSuite Cloud-Based Phone System Mitel IP Phone User Reference Guide Release 5.0 Final
OfficeSuite Cloud-Based Phone System Mitel IP Phone User Reference Guide Release 5.0 Final Note: The information contained in this document is the property of Broadview Networks Inc. and is disclosed to
More informationWireshark Tutorial INTRODUCTION
Wireshark Tutorial INTRODUCTION The purpose of this document is to introduce the packet sniffer WIRESHARK. WIRESHARK would be used for the lab experiments. This document introduces the basic operation
More information1 VoIP/PBX Axxess Server
- 1 1 VoIP/PBX Axxess Server The Axxess Server supports comprehensive Voice Over Internet Protocol network services, which are based on the Open Source Asterisk VoIP software. The Axxess Server VoIP telephony
More informationMITEL IP PHONE USER REFERENCE GUIDE Release 4.0
MITEL IP PHONE USER REFERENCE GUIDE Release 4.0 Simple as your phone. Smart as the internet. NOTICE The information contained in this document is believed to be accurate in all respects but is not warranted
More informationVoice Gateway with Router
Voice User Guide Model No. SPA3102 Copyright and Trademarks Specifications are subject to change without notice. Linksys is a registered trademark or trademark of Cisco Systems, Inc. and/or its affiliates
More informationSIP Proxy Server. Administrator Installation and Configuration Guide. V2.31b. 09SIPXM.SY2.31b.EN3
SIP Proxy Server Administrator Installation and Configuration Guide V2.31b 09SIPXM.SY2.31b.EN3 DSG, DSG logo, InterPBX, InterServer, Blaze Series, VG5000, VG7000, IP590, IP580, IP500, IP510, InterConsole,
More informationIP Office Phone Manager Users Guide
IP Office Phone Manager Users Guide 40DHB0002USAR Issue 6 (03/04/2002) Contents Getting Started... 3 Introduction... 3 Getting Started... 4 Phone Manager... 5 Main Window... 5 Call Status... 6 Call History...
More informationTraining Guide For 7960 & 7940 Series Cisco IP Phones
Training Guide For 7960 & 7940 Series Cisco IP Phones Prepared by: Corporate Technologies, LLC 2000 44 th Street SW, Suite 100 Fargo, ND 58103 (701) 893-4000 1 Table of Contents: Section I: GETTING STARTED
More informationLab 8.3.2 Conducting a Network Capture with Wireshark
Lab 8.3.2 Conducting a Network Capture with Wireshark Objectives Perform a network traffic capture with Wireshark to become familiar with the Wireshark interface and environment. Analyze traffic to a web
More informationShoreTel Enterprise Contact Center Using Agent Toolbar
ShoreTel Enterprise Contact Center Using Agent Toolbar USER GUIDES RELEASE 7 Document and Software Copyrights Copyright 1998 2011 ShoreTel, Inc. All rights reserved. Printed in the United States of America.
More informationLinksys Gateway SPA2100-SU Manual
Linksys Gateway SPA2100-SU Manual Manuel de l'utilisateur Table of Contents Looking for Basic Setup Instructions?... 3 Most Recent Version of this Manual... 3 Advanced Setup Instructions... 4 Wiring Your
More informationPhone Adapter. with 2 Ports for Voice-over-IP. Installation and Troubleshooting Guide. Model No. PAP2 Ver. 2. Voice
Phone Adapter with 2 Ports for Voice-over-IP Voice Installation and Troubleshooting Guide Model No. PAP2 Ver. 2 Copyright and Trademarks Specifications are subject to change without notice. Linksys is
More informationVoIP Intercom and Cisco Call Manager Server Setup Guide
The IP Endpoint Company VoIP Intercom and Cisco Call Manager Server Setup Guide CyberData Corporation 2555 Garden Road Monterey, CA 93940 T:831-373-201 F: 831-373-4193 www.cyberdata.net 2 1.0 Setup Diagram
More informationCisco IP Phone 7941 and 7961 User Guide
Cisco IP Phone 7941 and 7961 User Guide Depending on configuration, programmable buttons provide access to: Phone lines (line buttons) Speed-dial numbers (speed-dial buttons) 1 The buttons illuminate to
More informationSipura SPA-3102 Simplified Users Guide Version 1.1a In Progress :)
Sipura SPA-3102 Simplified Users Guide Version 1.1a In Progress :) A Step by Step Introduction Written by Jason from JMG Technology http://www.jmgtechnology.com.au Section 1 Getting Started When you receive
More informationShoreTel Enterprise Contact Center 8 Using Agent Toolbar
ShoreTel Enterprise Contact Center 8 Using Agent Toolbar November 2012 Legal Notices Document and Software Copyrights Copyright 1998-2012 by ShoreTel Inc., Sunnyvale, California, USA. All rights reserved.
More informationCisco IP Phone 7960G and Cisco IP Phone 7940G for Cisco IOS Telephony Services
CHAPTER 1 Cisco IP Phone 7960G and Cisco IP Phone 7940G for Cisco IOS Telephony Services Button Legend The Cisco IP Phone 7960G and the Cisco IP Phone 7940G differ only in the number of available line
More informationConnect the Host to attach to Fast Ethernet switch port Fa0/2. Configure the host as shown in the topology diagram above.
Lab 1.2.2 Capturing and Analyzing Network Traffic Host Name IP Address Fa0/0 Subnet Mask IP Address S0/0/0 Subnet Mask Default Gateway RouterA 172.17.0.1 255.255.0.0 192.168.1.1 (DCE) 255.255.255.0 N/A
More informationIntegrator Soft Client User Guide
Integrator Soft Client User Guide Contents Introduction... 3 Installing the Integrator Soft Client... 4 Signing in... 5 Passwords... 5 Settings and Configuration... 6 Telephony settings... 6 Interface
More informationCommunicator for Mac Help
Communicator for Mac Help About the ShoreTel Communicator Introduction to the ShoreTel Communicator for Mac ShoreTel Communicator elements Learn about the window layout, panels, icons, buttons and notifications
More informationExtension Manual. 3CX Assistant, MyPhone User portal, Dial codes & Voice mail for 3CX Phone System Version 8.0
Extension Manual 3CX Assistant, MyPhone User portal, Dial codes & Voice mail for 3CX Phone System Version 8.0 Copyright 2006-2009, 3CX ltd. http:// E-mail: info@3cx.com Information in this document is
More informationDPH-140S SIP Phone Quick User Guide
DPH-140S SIP Phone Quick User Guide Version 1.0 TABLE OF CONTENTS 1.0 INTRODUCTION... 1 2.0 PACKAGE CONTENT... 1 3.0 LIST OF FIGURES... 2 4.0 SUMMARY OF KEY FUNCTIONS... 3 5.0 CONNECTING THE IP PHONE...
More informationFrontier Tandem. Administrator User Guide. Version 2.4 January 28, 2013
Frontier Tandem Administrator User Guide Version 2.4 January 28, 2013 About This Document 1 Version 7.3 Jan 28, 2013 Frontier Tandem Administrator Guide CONFIDENTIAL About This Document The Frontier Small
More informationIntroduction to Wireshark Network Analysis
Introduction to Wireshark Network Analysis Page 2 of 24 Table of Contents INTRODUCTION 4 Overview 4 CAPTURING LIVE DATA 5 Preface 6 Capture Interfaces 6 Capture Options 6 Performing the Capture 8 ANALYZING
More informationCISCO IP PHONE MODEL 7960 & UNITY VOICEMAIL INCLUDES CISCO CALLMANAGER ATTENDANT CONSOLE. Getting Started Manual
CISCO IP PHONE MODEL 7960 & UNITY VOICEMAIL INCLUDES CISCO CALLMANAGER ATTENDANT CONSOLE Getting Started Manual... 3 Getting Started... 3 Using LCD Icons... 3 Using the IP Phone Configuration Utility...
More informationExtension Manual. User portal, Dial codes & Voice mail for 3CX Phone System Version 7.0
Extension Manual User portal, Dial codes & Voice mail for 3CX Phone System Version 7.0 Copyright 2006-2008, 3CX ltd. http:// E-mail: info@3cx.com Information in this document is subject to change without
More informationQ. The Phone Manager call banner disappears after being displayed for a couple of seconds...5 Q. The Phone Manager icon in the taskbar is blue and
Phone Manager FAQ s Q. The Phone Manager call banner disappears after being displayed for a couple of seconds...5 Q. The Phone Manager icon in the taskbar is blue and has a cross on it. 5 Q. Some options
More informationInter-Tel. 3000 IP Phone Quick Reference Guide
Inter-Tel 3000 IP Phone Quick Reference Guide Introduction to your IP Phone The Inter-Tel 3000 IP Phone provides the same functionality as the Inter-Tel 3000 digital telephone sets. It can be connected
More informationMiraCosta College now offers two ways to access your student virtual desktop.
MiraCosta College now offers two ways to access your student virtual desktop. We now feature the new VMware Horizon View HTML access option available from https://view.miracosta.edu. MiraCosta recommends
More informationSelf Help Guide IMPORTANT! Configuring Your Router With Your Modem. Please read the following carefully; This Guide refers to the following Products:
IMPORTANT! This Guide refers to the following Products: Configuring Your Router With Your Modem Please read the following carefully; Synopsis: A standard (Wireless) Router does not come equipped with the
More informationCISCO IP PHONE 6945 Series User Guide
CISCO IP PHONE 6945 Series User Guide Notes Page 15 VOICE MAIL Setting up Voice Mail for the First Time: Press the messages key on your phone. Follow the recorded instruction to record your name, record
More informationHelp Menu. Kakapo Systems Ltd 1
Help Menu 1. Introducing Unity 2. Initial Login and Setup 3. Getting Started 3.1. Resizing Unity 3.2. Maximising and Minimising 3.2.1. Using Unity From the System Tray 4. Call Control 4.1. Make a Call
More informationVirtual Integrated Design Getting started with RS232 Hex Com Tool v6.0
Virtual Integrated Design Getting started with RS232 Hex Com Tool v6.0 Copyright, 1999-2007 Virtual Integrated Design, All rights reserved. 1 Contents: 1. The Main Window. 2. The Port Setup Window. 3.
More informationIntroduction to Network Security Lab 1 - Wireshark
Introduction to Network Security Lab 1 - Wireshark Bridges To Computing 1 Introduction: In our last lecture we discussed the Internet the World Wide Web and the Protocols that are used to facilitate communication
More informationUnified Communicator Advanced Training Handout
Unified Communicator Advanced Training Handout About Unified Communicator Advanced (UCA) Video Summary (must have access to the internet for this to launch) http://www.mitel.tv/videos/mitel_unified_communicator_advanced_na
More informationVoIP Quick Start Guide
VoIP Quick Start Guide VoIP is made up of three elements: The Phone The Software (optional) The Web Version of the software (optional) Your new voice mail can be accessed by calling (971-722) 8988. Or,
More informationDigital Phone Installation & User Guide
Digital Phone Installation & User Guide Telephone #1 Voicemail PIN Telephone #2 Voicemail PIN skybeam high speed internet digital phone We would like you to verify that the 911 address we have for you
More informationITL Lab 5 - Performance Measurements and SNMP Monitoring 1. Purpose
Lab 5 - Performance Measurements and SNMP Monitoring 1 Purpose Before the Lab Measure the performance (throughput) of TCP connections Measure the performance of UDP connections; observe an RTP flow Examine
More informationVoice over IP. Demonstration 1: VoIP Protocols. Network Environment
Voice over IP Demonstration 1: VoIP Protocols Network Environment We use two Windows workstations from the production network, both with OpenPhone application (figure 1). The OpenH.323 project has developed
More informationDSG SoftPhone & USB Phone Series User Guide
DSG SoftPhone & USB Phone Series User Guide Table of Contents Overview Before You Start Installation Step 1. Installing DSG SoftPhone Step 2. Installing USB Phone Step 3. System Check First Time Use Step
More informationMediatrix 4404 Step by Step Configuration Guide June 22, 2011
Mediatrix 4404 Step by Step Configuration Guide June 22, 2011 Proprietary 2011 Media5 Corporation Table of Contents First Steps... 3 Identifying your MAC Address... 3 Identifying your Dynamic IP Address...
More informationCaller ID Tracker 2005 - Summit Computer Networks, Inc.
Caller ID Tracker 2005 - Summit Computer Networks, Inc. This is a caller ID monitoring & logging system to be used with Windows based PCs. This software is for use with the Whozz Calling caller ID units
More informationUsing the Cisco IP Phone 7940/7960
CHAPTER 3 Using the Cisco IP Phone 7940/7960 Your Cisco IP Phone 7940/7960 provides features you might not have had before on an office phone. You can learn how to use these features by exploring the available
More informationLab 1: Introduction to the network lab
CSCI 312 - DATA COMMUNICATIONS AND NETWORKS FALL, 2014 Lab 1: Introduction to the network lab NOTE: Be sure to bring a flash drive to the lab; you will need it to save your data. For this and future labs,
More informationHosted PBX Phone Setup & End User Training Guide
Hosted PBX Phone Setup & End User Training Guide HOSTED PBX PHONE SETUP GUIDE REQUIRED FOR INSTALL Modem / Router Ethernet Power Supply or Switch (CAT5, CAT5e, CAT6) (if required) POLYCOM SOUNDPOINT IP
More informationAllworx Call Assistant 2.3 Quick Reference Guide
Allworx Call Assistant 2.3 Quick Reference Guide No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, photocopy,
More informationADSL Router Quick Installation Guide Revised, edited and illustrated by Neo
ADSL Router Quick Installation Guide Revised, edited and illustrated by Neo A typical set up for a router PCs can be connected to the router via USB or Ethernet. If you wish to use a telephone with the
More informationUsing Avaya Flare Experience for Windows
Using Avaya Flare Experience for Windows Release 9.0 Issue 02.01 September 2013 Contents Chapter 1: About Flare Experience... 5 About Flare Experience... 5 Main window... 6 Button descriptions... 10 Chapter
More informationCloud Voice Service Remote Extension for Cisco Unified IP Phone 7942G User Guide
Cloud Voice Service Remote Extension for Cisco Unified IP Phone 7942G User Guide (Version 1.0) Table of Content 1. Phone Set Features and Functions... 2 1.1 Setup the IP Phone... 3 1.2 Adjusting the Height
More informationNote: these functions are available if service provider supports them.
Key Feature New Feature Remote Maintenance: phone can be diagnosed and configured by remote. Zero Config: automated provisioning and software upgrading even through firewall/nat. Centralized Management:
More informationHow to Program a Commander or Scout to Connect to Pilot Software
How to Program a Commander or Scout to Connect to Pilot Software Commander and Scout are monitoring and control products that can transfer physical environmental conditions and alarm sensor electrical
More informationEnd User Training Guide
End User Training Guide Everything You Need to Get Started on Vonage Business Solutions End User Portal This guide will give you a comprehensive look at the Vonage Business Solutions online user interface
More informationUsing Basic Call Management Functions
Using Basic Call Management Functions This chapter provides instructions on using your basic phone functions. It includes the following sections: Managing the Audio Source and Volume, page 28 Answering
More informationLab 2.1 Configure CME using the CLI and Cisco IP Communicator
Lab 2.1 Configure CME using the CLI and Cisco IP Communicator Learning Objectives Configure Cisco Unified Call Manager Express (CME) Install Cisco IP Communicator (CIPC) on a host Verify CME and CIPC Operation
More informationAvaya one-x Communicator User Reference
Avaya one-x Communicator User Reference November 2009 Table Of Contents Introduction...1 Log into the server...3 Log out of the server...5 Use your feature buttons...7 Use Avaya one-x Communicator with
More informationUSER GUIDE Cisco Small Business
USER GUIDE Cisco Small Business IP Phone Model SPA92X, SPA94X, and SPA962 Contents Chapter 1: Getting Started 6 Overview of the Cisco SPA9000 Voice System IP Phones 6 SPA921/922 IP Phone 8 SPA941/942 IP
More informationPre-lab and In-class Laboratory Exercise 10 (L10)
ECE/CS 4984: Wireless Networks and Mobile Systems Pre-lab and In-class Laboratory Exercise 10 (L10) Part I Objectives and Lab Materials Objective The objectives of this lab are to: Familiarize students
More informationReceptionist console. User guide 1.1
Receptionist console User guide 1.1 Contents Introduction and purpose... 4 Common deployments of the receptionist console... 5 Fixed Receptionist Console... 5 Soft Receptionist Console... 5 Multiple site
More information