DESIGN GUIDELINES AND STANDARDS

Transcription

1 DESIGN GUIDELINES AND STANDARDS

2 Table of Contents Table of Contents Procurement and Contracting Requirements Application for Payment Form for AE Services Summary Construction Insurance Requirements EXHIBIT General Requirements Regulatory Requirements UNF Acid Dilution Tank Exemption EXHIBIT Project Identification Temporary Project Signage EXHIBIT Closeout Procedures Operation and Maintenance Data Sustainable Design Requirements Facility Shell Performance Requirements Interiors Performance Requirements UNF Custodial Work Rooms Diagram EXHIBIT Other Facility Construction Performance Requirements Site Improvements Performance Requirements Metals Decorative Metal Railings EXHIBIT Thermal & Moisture Protection Styrene-Butadiene-Styrene Modified Bituminous Roofing Openings General Product Procurement and Installation Matrix EXHIBIT Metal Doors and Frames Frame Tolerances EXHIBIT Wood Doors Entrances and Storefronts Door Hardware Glazing Louvers Finishes General Finish Information Resilient Flooring and Accessories Tile Carpeting Specialties 107 Revised: 12/16/2010

3 Table of Contents General Specialties Information Panel Signage Traffic Signage Toilet Compartments Fire Extinguishers Transportation Stop Shelters Transportation Stop Shelters EXHIBIT Furnishings General Furnishings Information Simulated Stone Countertops Waste Receptacles Rugs and Mats Rugs and Mats EXHIBIT Rugs and Mats EXHIBIT Office Furniture Typical Office Layout EXHIBIT Office Furniture Typical Office Layout EXHIBIT Office Furniture Typical Office Layout EXHIBIT Classroom Furniture Site Furnishings Conveying Equipment General Elevator Requirements Fire Suppression Wet-Pipe Sprinkler Systems Plumbing Plumbing Project Requirements Common Motor Requirements for Plumbing Equipment Meters and Gages for Plumbing Piping General-Duty Valves for Plumbing Equipment Identification for Plumbing Piping and Equipment Domestic Water Piping Domestic Water Piping Specialties Domestic Water Pumps Sanitary Waste and Vent Piping Facility Storm Drainage Piping Plumbing Fixtures Heating, Ventilating, and Air-Conditioning (Hvac) 160 Revised: 12/16/2010

4 Table of Contents Hvac Project Requirements Common Work Results For Hvac Common Motor Requirements for Hvac Equipment Meters and Gages for Hvac Piping General-Duty Valves for Hvac Piping Identification for Hvac Piping and Equipment Testing, Adjusting, and Balancing Hvac Insulation Hydronic Piping Metal Ducts Centrifugal Hvac Fans Air Terminal Units Diffusers, Registers, and Grilles Modular Indoor Central-Station Air Handling Units Fan Coil Units Integrated Automation Integrated Automation Facility Controls Electrical Electrical Project Requirements Common Work Results For Electrical Low-Voltage Electrical Power Conductors and Cables Raceway and Boxes for Electrical Systems Identification for Electrical Systems Lighting Control Devices Switchboards Panelboards Electricity Metering Wiring Devices Variable-Frequency Motor Controllers Engine Generators Transfer Switches Lightning Protection for Structures Transient-Voltage Suppression for Low-Voltage Electrical Power Circuits Interior Lighting Exterior Lighting General Communication Requirements Technology Legends and Symbols EXHIBIT Revised: 12/16/2010

5 Table of Contents Communications Communications EXHIBIT Communications EXHIBIT Communications EXHIBIT Communications EXHIBIT Communications EXHIBIT Communications EXHIBIT Common Work Results For Communications Communications Equipment Room Fittings Communications Backbone Cabling Communications Services Cabling Communications Horizontal Cabling Ring-Down Emergency Telephones Ring-Down Emergency Telephones - EXHIBIT Audio-Video Systems Electronic Safety and Security General Safety and Security Requirements General Safety and Security Requirements EXHIBIT Fire Detection and Alarm Exterior Improvements General Landscape and Irrigation Information Paving Specialties EXHIBIT Tactile Warning Surfacing Irrigation Planting Revised: 12/16/2010

6 Procurement and Contracting Requirements Page 1 of 330 Revised: 12/16/2010

7 Application for Payment Form for AE Services Application for Payment Form for AE Services All Applications for Payment shall include the information in the following UNF AE Services Invoice Template EXHIBIT 1. Page 2 of 330 Revised: 12/16/2010

8 Summary Construction Insurance Requirements EXHIBIT Summary Construction Insurance Requirements EXHIBIT 1 This summary is intended to assist you in preparing the Surety Bonds and Certificates of Insurance contractually required by the University s Construction contract documents. It is important to note Certificate of Insurance acceptable to the Owner (University of North Florida) shall be filed with the Owner prior to execution of the formal contractual agreement. The University of North Florida Board of Trustees and the Florida Board of Governors must be named as the Certificate Holder and as Additional Named Insureds as to the operations of the contractor under the Agreement and shall provide the Severability of Insureds Provision and a Waiver of Subrogation in favor of the Owner on all liability policies. Waiver of Subrogation is also required on all Property Insurance as well as naming the University of North Florida Board of Trustees and the Florida Board of Governors as Additional Named Insureds. The A M Best Insurance Company rating requirements for projects in excess of $500,000 are: Contract Amount Best Rating Required Financial Size $10,000,000+ A IX ($250 million to $500 million) $1,500,000 to 9,999,999 $1,000,000 to $1,499,999 A VIII ($100 million to $250 million) A VII ($50 million to $100 million) $750,000 to 999,999 A VI ($25 million to $50 million) $500,000 to 749,999 A V ($10 million to $25 million) Page 3 of 330 Revised: 12/16/2010

9 Summary Construction Insurance Requirements EXHIBIT 1 If any liability insurance is written on a Claims Made Form, the Retroactive date of Coverage must also be included on the Certificate of Insurance. Certificates of Insurance must include the specific Project Name. The Owner (University of North Florida) shall be exempt from and in no way liable for any sums of money which may represent a deductible in any insurance policy. Each Certificate of Insurance must be countersigned (with name of agent signing the certificate also printed on the certificate) by a lawfully licensed agent in the State of Florida and the agent must be appointed to represent the companies shown on the certificate. Excerpts from the Sections of the project manual specific to the insurance requirements are attached for your convenience The Owner s accountants will review and report in writing on the Construction Manager s final accounting within 30 days after delivery of the final accounting to the Architect by the Construction Manager. Based upon such Cost of the Work as the Owner s accountants report to be substantiated by the Construction Manager s final accounting, and provided the other conditions of Section have been met, the Architect will, within seven days after receipt of the written report of the Owner s accountants, either issue to the Owner a final Certificate for Payment with a copy to the Construction Manager or notify the Construction Manager and Owner in writing of the Architect s reasons for withholding a certificate as provided in Section of A201 TM The time periods stated in this Section 7.2 supersede those stated in Section of A201 TM If the Owner s accountants report the Cost of the Work as substantiated by the Construction Manager s final accounting to be less than claimed by the Construction Manager, the Construction Manager shall be entitled to proceed in accordance with Article 9 without a further decision of the Architect. Unless agreed to otherwise, a demand for mediation of the disputed amount shall be made by the Construction Manager within 60 days after the Construction Manager s receipt of a copy of the Architect s final Certificate for Payment. Failure to make such demand within this 60-day period shall result in the substantiated amount reported by the Owner s accountants becoming binding on the Construction Manager. Pending a final resolution of the disputed amount, the Owner shall pay the Construction Manager the amount certified in the Architect s final Certificate for Payment If, subsequent to final payment and at the Owner s request, the Construction Manager incurs costs described in Section 6.1 and not excluded by Section 6.2 (1) to correct nonconforming Work or (2) arising from the resolution of disputes, the Owner Page 4 of 330 Revised: 12/16/2010

10 Summary Construction Insurance Requirements EXHIBIT 1 shall reimburse the Construction Manager such costs and the Construction Manager s Fee, if any, related thereto on the same basis as if such costs had been incurred prior to final payment, but not in excess of the Guaranteed Maximum Price. If the Construction Manager has participated in savings, the amount of such savings shall be recalculated and appropriate credit given to the Owner in determining the net amount to be paid by the Owner to the Construction Manager. ARTICLE 8 INSURANCE AND BONDS 8.1 INSURANCE REQUIRED OF THE CONSTRUCTION MANAGER During both phases of the Project, the Construction Manager shall purchase and maintain insurance as set forth in Section 11.1 of A201 TM (If Umbrella Excess Liability coverage is required over the primary insurance or retention, insert the coverage limits. Commercial General Liability and Automobile Liability limits may be attained by individual policies or by a combination of primary policies and Umbrella and/or Excess Liability policies. If Project Management Protective Liability Insurance is to be provided, state the limits here.) (Paragraphs deleted) 8.2 INSURANCE REQUIRED OF THE OWNER Intentionally deleted. (Paragraphs deleted) 8.3 PERFORMANCE BOND AND PAYMENT BOND The Construction Manager shall furnish bonds covering faithful performance of the Contract and payment of obligations arising thereunder. Bonds shall be in the form prescribed by Owner, and the cost of bonds shall be included in the Cost of the Work. The amount of each bond shall be equal to 100% (one hundred percent) of the Contract Sum The Construction Manager shall deliver the required bonds to the Owner at least three days before the commencement of any Work at the Project site If, without negligence on the part of the Contractor, the Contractor is held liable for the cost of remediation of a hazardous material or substance solely by reason of performing Work as required by the Contract Documents, the Owner shall indemnify the Contractor for all cost and expense thereby incurred. Page 5 of 330 Revised: 12/16/2010

11 Summary Construction Insurance Requirements EXHIBIT EMERGENCIES In an emergency affecting safety of persons or property, the Contractor shall act, at the Contractor s discretion, to prevent threatened damage, injury or loss. Additional compensation or extension of time claimed by the Contractor on account of an emergency shall be determined as provided in Section 4.3 and Article 7. ARTICLE 11 INSURANCE AND BONDS 11.1 CONTRACTOR S LIABILITY INSURANCE The Contractor shall purchase from and maintain in a company or companies lawfully authorized to do business in the jurisdiction in which the Project is located such insurance as will protect the Contractor from claims set forth below which may arise out of or result from the Contractor s operations under the Contract and for which the Contractor may be legally liable, whether such operations be by the Contractor or by a Subcontractor or by anyone directly or indirectly employed by any of them, or by anyone for whose acts any of them may be liable:.1 claims under workers compensation, disability benefit and other similar employee benefit acts which are applicable to the Work to be performed;.2 claims for damages because of bodily injury, occupational sickness or disease, or death of the Contractor s employees;.3 claims for damages because of bodily injury, sickness or disease, or death of any person other than the Contractor s employees;.4 claims for damages insured by usual personal injury liability coverage;.5 claims for damages, other than to the Work itself, because of injury to or destruction of tangible property, including loss of use resulting therefrom;.6 claims for damages because of bodily injury, death of a person or property damage arising out of ownership, maintenance or use of a motor vehicle;.7 claims for bodily injury or property damage arising out of completed operations; and.8 claims involving contractual liability insurance applicable to the Contractor s obligations under Section The insurance required by Section shall be written for not less than limits of liability specified in the Contract Documents or required by law, whichever Page 6 of 330 Revised: 12/16/2010

12 Summary Construction Insurance Requirements EXHIBIT 1 coverage is greater. Coverages, whether written on an occurrence or claims-made basis, shall be maintained without interruption from date of commencement of the Work until date of final payment and termination of any coverage required to be maintained after final payment Certificates of insurance acceptable to the Owner shall be filed with the Owner prior to commencement of the Work. These certificates and the insurance policies required by this Section 11.1 shall contain a provision that coverages afforded under the policies will not be canceled or allowed to expire until at least 30 days prior written notice has been given to the Owner. If any of the foregoing insurance coverages are required to remain in force after final payment and are reasonably available, an additional certificate evidencing continuation of such coverage shall be submitted with the final Application for Payment as required by Section Information concerning reduction of coverage on account of revised limits or claims paid under the General Aggregate, or both, shall be furnished by the Contractor with reasonable promptness in accordance with the Contractor s information and belief OWNER S LIABILITY INSURANCE The Owner shall be responsible for purchasing and maintaining the Owner s usual liability insurance PROJECT MANAGEMENT PROTECTIVE LIABILITY INSURANCE Optionally, the Owner may require the Contractor to purchase and maintain Project Management Protective Liability insurance from the Contractor s usual sources as primary coverage for the Owner s, Contractor s and Architect s vicarious liability for construction operations under the Contract. Unless otherwise required by the Contract Documents, the Owner shall reimburse the Contractor by increasing the Contract Sum to pay the cost of purchasing and maintaining such optional insurance coverage, and the Contractor shall not be responsible for purchasing any other liability insurance on behalf of the Owner. The minimum limits of liability purchased with such coverage shall be equal to the aggregate of the limits required for Contractor s Liability Insurance under Sections through To the extent damages are covered by Project Management Protective Liability insurance, the Owner, Contractor and Architect waive all rights against each other for damages, except such rights as they may have to the proceeds of such insurance. The policy shall provide for such waivers of subrogation by endorsement or otherwise. Page 7 of 330 Revised: 12/16/2010

13 Summary Construction Insurance Requirements EXHIBIT The Owner shall not require the Contractor to include the Owner, Architect or other persons or entities as additional insureds on the Contractor s Liability Insurance coverage under Section PROPERTY INSURANCE Unless otherwise provided, the Owner shall purchase and maintain, in a company or companies lawfully authorized to do business in the jurisdiction in which the Project is located, property insurance written on a builder s risk all-risk or equivalent policy form in the amount of the initial Contract Sum, plus value of subsequent Contract modifications and cost of materials supplied or installed by others, comprising total value for the entire Project at the site on a replacement cost basis without optional deductibles. Such property insurance shall be maintained, unless otherwise provided in the Contract Documents or otherwise agreed in writing by all persons and entities who are beneficiaries of such insurance, until final payment has been made as provided in Section 9.10 or until no person or entity other than the Owner has an insurable interest in the property required by this Section 11.4 to be covered, whichever is later. This insurance shall include interests of the Owner, the Contractor, Subcontractors and Sub-subcontractors in the Project Property insurance shall be an all-risk or equivalent policy form and shall include, without limitation, insurance against the perils of fire (with extended coverage) and physical loss or damage including, without duplication of coverage, theft, vandalism, malicious mischief, collapse, earthquake, flood, windstorm, falsework, testing and startup, temporary buildings and debris removal including demolition occasioned by enforcement of any applicable legal requirements, and shall cover reasonable compensation for Architect s and Contractor s services and expenses required as a result of such insured loss If the Owner does not intend to purchase such property insurance required by the Contract and with all of the coverages in the amount described above, the Owner shall so inform the Contractor in writing prior to commencement of the Work. The Contractor may then effect insurance which will protect the interests of the Contractor, Subcontractors and Sub-subcontractors in the Work, and by appropriate Change Order the cost thereof shall be charged to the Owner. If the Contractor is damaged by the failure or neglect of the Owner to purchase or maintain insurance as described above, without so notifying the contractor in writing, then the Owner shall bear all reasonable costs properly attributable thereto If the property insurance requires deductibles, the Owner shall pay costs not covered because of such deductibles. Page 8 of 330 Revised: 12/16/2010

14 Summary Construction Insurance Requirements EXHIBIT This property insurance shall cover portions of the Work stored off the site, and also portions of the Work in transit Partial occupancy or use in accordance with Section 9.9 shall not commence until the insurance company or companies providing property insurance have consented to such partial occupancy or use by endorsement or otherwise. The Owner and the Contractor shall take reasonable steps to obtain consent of the insurance company or companies and shall, without mutual written consent, take no action with respect to partial occupancy or use that would cause cancellation, lapse or reduction of insurance Boiler and Machinery Insurance. The Owner shall purchase and maintain boiler and machinery insurance required by the Contract Documents or by law, which shall specifically cover such insured objects during installation and until final acceptance by the Owner; this insurance shall include interests of the Owner, Contractor, Subcontractors and Sub-subcontractors in the Work, and the Owner and Contractor shall be named insureds Loss of Use Insurance. The Owner, at the Owner s option, may purchase and maintain such insurance as will insure the Owner against loss of use of the Owner s property due to fire or other hazards, however caused. The Owner waives all rights of action against the Contractor for loss of use of the Owner s property, including consequential losses due to fire or other hazards however caused If the Contractor requests in writing that insurance for risks other than those described herein or other special causes of loss be included in the property insurance policy, the Owner shall, if possible, include such insurance, and the cost thereof shall be charged to the Contractor by appropriate Change Order If during the Project construction period the Owner insures properties, real or personal or both, at or adjacent to the site by property insurance under policies separate from those insuring the Project, or if after final payment property insurance is to be provided on the completed Project through a policy or policies other than those insuring the Project during the construction period, the Owner shall waive all rights in accordance with the terms of Section for damages caused by fire or other causes of loss covered by this separate property insurance. All separate policies shall provide this waiver of subrogation by endorsement or otherwise Before an exposure to loss may occur, the Owner shall file with the Contractor a copy of each policy that includes insurance coverages required by this Section Each policy shall contain all generally applicable conditions, definitions, exclusions and endorsements related to this Project. Each policy shall contain a Page 9 of 330 Revised: 12/16/2010

15 Summary Construction Insurance Requirements EXHIBIT 1 provision that the policy will not be canceled or allowed to expire, and that its limits will not be reduced, until at least 30 days prior written notice has been given to the Contractor Waivers of Subrogation. The Owner and Contractor waive all rights against (1) each other and any of their subcontractors, sub-subcontractors, agents and employees, each of the other, and (2) the Architect, Architect s consultants, separate contractors described in Article 6, if any, and any of their subcontractors, subcontractors, agents and employees, for damages caused by fire or other causes of loss to the extent covered by property insurance obtained pursuant to this Section 11.4 or other property insurance applicable to the Work, except such rights as they have to proceeds of such insurance held by the Owner as fiduciary. The Owner or Contractor, as appropriate, shall require of the Architect, Architect s consultants, separate contractors described in Article 6, if any, and the subcontractors, subsubcontractors, agents and employees of any of them, by appropriate agreements, written where legally required for validity, similar waivers each in favor of other parties enumerated herein. The policies shall provide such waivers of subrogation by endorsement or otherwise. A waiver of subrogation shall be effective as to a person or entity even though that person or entity would otherwise have a duty of indemnification, contractual or otherwise, did not pay the insurance premium directly or indirectly, and whether or not the person or entity had an insurable interest in the property damaged A loss insured under Owner s property insurance shall be adjusted by the Owner as fiduciary and made payable to the Owner as fiduciary for the insureds, as their interests may appear, subject to requirements of any applicable mortgagee clause and of Section The Contractor shall pay Subcontractors their just shares of insurance proceeds received by the Contractor, and by appropriate agreements, written where legally required for validity, shall require Subcontractors to make payments to their Sub-subcontractors in similar manner If required in writing by a party in interest, the Owner as fiduciary shall, upon occurrence of an insured loss, give bond for proper performance of the Owner s duties. The cost of required bonds shall be charged against proceeds received as fiduciary. The Owner shall deposit in a separate account proceeds so received, which the Owner shall distribute in accordance with such agreement as the parties in interest may reach, or in accordance with an arbitration award in which case the procedure shall be as provided in Section 4.6. If after such loss no other special agreement is made and unless the Owner terminates the Contract for convenience, replacement of damaged property shall be performed by the Contractor after notification of a Change in the Work in accordance with Article 7. Page 10 of 330 Revised: 12/16/2010

16 Summary Construction Insurance Requirements EXHIBIT The Owner as fiduciary shall have power to adjust and settle a loss with insurers unless one of the parties in interest shall object in writing within five days after occurrence of loss to the Owner s exercise of this power; if such objection is made, the dispute shall be resolved as provided in Sections 4.5 and 4.6. The Owner as fiduciary shall, in the case of arbitration, make settlement with insurers in accordance with directions of the arbitrators. If distribution of insurance proceeds by arbitration is required, the arbitrators will direct such distribution PERFORMANCE BOND AND PAYMENT BOND The Owner shall have the right to require the Contractor to furnish bonds covering faithful performance of the Contract and payment of obligations arising thereunder as stipulated in bidding requirements or specifically required in the Contract Documents on the date of execution of the contract Upon the request of any person or entity appearing to be a potential beneficiary of bonds covering payment of obligations arising under the Contract, the Contractor shall promptly furnish a copy of the bonds or shall permit a copy to be made. ARTICLE 12 UNCOVERING AND CORRECTION OF WORK 12.1 UNCOVERING OF WORK If a portion of the Work is covered contrary to the Architect s request or to requirements specifically expressed in the Contract Documents, it must, if required in writing by the Architect, be uncovered for the Architect s examination and be replaced at the Contractor s expense without change in the Contract Time If a portion of the Work has been covered which the Architect has not specifically requested to examine prior to its being covered, the Architect may request to see such Work and it shall be uncovered by the Contractor. If such Work is in accordance with the Contract Documents, costs of uncovering and replacement shall, by appropriate Change Order, be at the Owner s expense. If such Work is not in accordance with the Contract Documents, correction shall be at the Contractor s expense unless the condition was caused by the Owner or a separate contractor in which event the Owner shall be responsible for payment of such costs CORRECTION OF WORK BEFORE OR AFTER SUBSTANTIAL COMPLETION Page 11 of 330 Revised: 12/16/2010

17 Summary Construction Insurance Requirements EXHIBIT The Contractor shall promptly correct Work rejected by the Architect or failing to conform to the requirements of the Contract Documents, whether discovered before or after Substantial Completion and whether or not fabricated, installed or completed. Costs of correcting such rejected Work, including additional testing and inspections and compensation for the Architect s services and expenses made necessary thereby, shall be at the Contractor s expense AFTER SUBSTANTIAL COMPLETION In addition to the Contractor s obligations under Section 3.5, if, within one year after the date of Substantial Completion of the Work or designated portion thereof or after the date for commencement of warranties established under Section 9.9.1, or by terms of an applicable special warranty required by the Contract Documents, any of the Work is found to be not in accordance with the requirements of the Contract Documents, the contractor shall correct it promptly after receipt of written notice from the Owner to do so unless the Owner has previously given the Contractor a written acceptance of such condition. The Owner shall give such notice promptly after discovery of the condition. During the one-year period for correction of Work, if the Owner fails to notify the Contractor and give the Contractor an opportunity to make the correction, the Owner waives the rights to require correction by the Contractor and to make a claim for breach of warranty. If the Contractor fails to correct nonconforming Work within a reasonable time during that period after receipt of notice from the Owner or Architect, the Owner may correct it in accordance with Section The one-year period for correction of Work shall be extended with respect to portions of Work first performed after Substantial completion by the period of time between Substantial Completion and the actual performance of the Work The one-year period for correction of Work shall not be extended by corrective Work performed by the Contractor pursuant to this Section The Contractor shall remove from the site portions of the Work which are not in accordance with the requirements of the Contract Documents and are neither corrected by the Contractor nor accepted by the Owner The Contractor shall bear the cost of correcting destroyed or damaged construction, whether completed or partially completed, of the Owner or separate contractors caused by the Contractor s correction or removal of Work which is not in accordance with the requirements of the Contract Documents Nothing contained in this Section 12.2 shall be construed to establish a period of limitation with respect to other obligations which the Contractor might have Page 12 of 330 Revised: 12/16/2010

18 Summary Construction Insurance Requirements EXHIBIT 1 under the Contract Documents. Establishment of the one-year period for correction of Work as described in Section relates only to the specific obligation of the Contractor to correct the Work, and has no relationship to the time within the obligation to comply with the Contract [document continuation?] endorsed or prohibited, and utilizing all personal protection devices included, within OSHA and MIOSHA Construction Safety Regulations. The Contractor shall take all necessary precautions for the safety of the persons on or near the site of the Work, and shall comply with all applicable laws, rules, regulations and orders to prevent accidents or injuries to persons on or in the proximity of the project site. The Contractor shall put into place a meaningful and effective safety program comprised of regular safety training of its employees on site, focusing upon various topics which, from time to time, its employees are likely to encounter in performing the Work. The Owner will cooperate with all safety audits and recommendations with regard to improving worker s safety, but the Contractor hereby acknowledges and agrees that the Owner is not responsible, in whole or in part, for the Work, execution of the Work or initiating, maintaining and supervising any safety precautions and programs in connection with the Work or the Project. ARTICLE 11 Section is deleted and replaced with the following: Commercial General Liability Insurance. The Contractor shall provide and maintain throughout its performance of the Work a commercial general liability insurance policy which has liability limits of at least $2,000,000 per occurrence for bodily injury, death and property damage, with a deductible no greater than $50,000. Such insurance shall be provided by a bona fide insurer licensed to provide insurance coverage within the State of Florida maintaining an A rating. The University of North Florida Board of Trustees, State of Florida, their employees, directors, officers, and agents shall be named insureds on such policy, and the policy shall provide cross liability coverage. Such insurance policy shall protect the Contractor from Claims which may arise out of or result from the Contractor s operations under the Contract Documents and for which the Contractor may be legally liable, whether such operations be by the Contractor or by a Subcontractor or by anyone directly or indirectly employed by any of them, or by anyone for whose acts any of them may be liable. In addition, the policy shall contain the following endorsements: (i) XCU (explosion, collapse, underground damage) for those classifications excluded under the policy and (ii) contractual liability. If the Contractor is performing asbestos-related work, the policy shall also contain a pollution liability endorsement. Page 13 of 330 Revised: 12/16/2010

19 Summary Construction Insurance Requirements EXHIBIT 1 Automobile Liability Insurance. The Contractor shall carry automobile liability insurance which has liability limits of at least $500, Worker s Compensation Insurance. The Contractor shall maintain worker s compensation insurance which complies with the requirements of Chapter 440, Florida Statutes. The first sentence of Section is deleted. The first two sentences of Section are deleted and replaced with the following: Certificates of Insurance and/or evidence of insurance for all insurance required to be carried under this Article, together with certified copies of the insurance policies (including required endorsements), shall be filed with, and approved by, the Owner prior to commencement of the Work. The Certificates of insurance shall be dated and show the name of the Insurer, the number of the policy, its effective date, and its termination date. Owner will not issue a notice to proceed for the Work until Contractor has complied with this Article. Contractor shall not be entitled to an extension of time or to compensation which may result from delays in the issuance of a notice to proceed caused by its failure to provide the foregoing certificates and policies in a timely manner. Certificates of insurance evidencing the renewal of all Insurance required to be carried under this Article shall be provided to Owner at least thirty (30) days prior to the date each applicable insurance policy is scheduled to expire. Owner s review, inspection, or approval of Contractor s insurance shall not relieve Contractor of its responsibility for providing the insurance required hereby nor constitute a waiver of any such requirements. Delete Section Add the following Section: The Owner is exempt from and in no way liable for any sums of money which may represent a deductible in any insurance policy. The payment of any deductible shall be the sole responsibility of the Contractor or Subcontractor providing the insurance. Delete Section Delete Section 11.3 and replace it with the following: Page 14 of 330 Revised: 12/16/2010

20 Summary Construction Insurance Requirements EXHIBIT Builder s Risk Insurance. The Contractor shall maintain builder s risk insurance, at replacement cost covering the full value of the construction being performed, including where applicable, the existing structure. This insurance shall insure the interests of the Contractor, Subcontractors and Sub-subcontractors in the Work. Property covered by the insurance shall include temporary building(s) or structure(s) at the Project site, other than any of Contractor s office trailer(s). In addition, such insurance shall cover portions of the Work stored off the site, after written approval of the Owner, at the value established in the approval, and portions of the Work in transit. This insurance shall be maintained until Final Payment has been made as provided in Section 9.10 or until no person or entity other than the Owner has an insurable interest in the property required by this Section 11.4 to be covered, whichever is later, provided that such coverage shall not be required as to any portion of the Project which Owner has actually occupied prior to final completion. This insurance shall be provided by a bona fide insurer licensed to provide insurance coverage within the State of Florida maintaining an A rating. The University of North Florida Board of Trustees and the State of Florida, their employees, directors, officers and agents shall be named insureds on such policy. The policy shall include a waiver of subrogation endorsement and a severability of interests endorsement. Delete Section and replace it with the following: Such policy shall be written on a causes of loss special form policy, and shall include coverage for reasonable compensation for the Architect s services and expenses required as a result of such insured loss. Delete Section Add the following sentence to the end of Section : The deductible under the policy shall not exceed $5, Owner shall not be liable for amounts that may represent a deductible in any insurance policy. The payment of such deductible shall be the sole responsibility of the Contractor. Delete Section and replace it with the following: When the Work includes the repair, removal, installation and/or testing of live steam boilers, valves, pipes or lines, then such insurance shall include boiler and machine coverage, written on an ISO form or its equivalent. Delete Sections , , and Page 15 of 330 Revised: 12/16/2010

21 Summary Construction Insurance Requirements EXHIBIT 1 Delete Section and replace it with the following: Waiver of Subrogation. The Contractor hereby releases and discharges the Owner, State of Florida and Florida Board of Governors from all liability to the Contractor, and to anyone claiming by, through or under the Contractor, by subrogation or otherwise, on account of any loss or damage to tools, machinery, equipment or other property, however caused. The Contractor shall cause its Contractor s risk property insurance company to issue a waiver of subrogation consistent with this provision. Delete Section and replace it with the following: A loss or losses insured under this insurance policy shall be adjusted by the Contractor and its insurance company. The Contractor shall repair or replace the damaged property with the proceeds from the Contractor s risk policy. The Contractor shall be responsible for all damages and necessary repairs whether or not the loss is covered by the Contractor s risk policy. Delete Sections and Add the following Section: Compliance with insurance requirements shall not relieve the Contractor of any responsibility to indemnify the Owner for any liability to the Owner as specified in any other provision of the Contract for Construction, and the Owner shall be entitled to pursue any remedy in law or equity if the Contractor fails to comply with the provisions of this Contract for Construction. Indemnity obligations specified elsewhere in this Contract for Construction shall not be negated or reduced by virtue of any insurance carrier s (i) denial of insurance coverage for the occurrence of event which is the subject matter of the claim; or (ii) refusal to defend any named insured. Delete Section and replace it with the following: The Contractor shall furnish bonds in the form prescribed by Owner covering faithful performance of the Contract and payment of obligations arising thereunder in the full sum of the Contract and otherwise in compliance with the requirements of Florida Statutes Section Add the following Section: Page 16 of 330 Revised: 12/16/2010

22 Summary Construction Insurance Requirements EXHIBIT The Contractor shall deliver the required bonds to the Owner prior to commencement of the Work. ARTICLE 12 [This appears incomplete.] Page 17 of 330 Revised: 12/16/2010

23 General Requirements Page 18 of 330 Revised: 12/16/2010

24 Regulatory Requirements Regulatory Requirements UNF Acid Dilution Tank Exemption EXHIBIT 1 Page 19 of 330 Revised: 12/16/2010

25 UNF Acid Dilution Tank Exemption EXHIBIT UNF Wind Zone Ordinance EXHIBIT 2 Page 20 of 330 Revised: 12/16/2010

26 UNF Acid Dilution Tank Exemption EXHIBIT 1 Page 21 of 330 Revised: 12/16/2010

27 UNF Acid Dilution Tank Exemption EXHIBIT 1 Page 22 of 330 Revised: 12/16/2010

28 UNF Acid Dilution Tank Exemption EXHIBIT 1 Page 23 of 330 Revised: 12/16/2010

29 UNF Acid Dilution Tank Exemption EXHIBIT 1 Page 24 of 330 Revised: 12/16/2010

30 UNF Acid Dilution Tank Exemption EXHIBIT UNF Landscape MOU With County EXHIBIT 3 Page 25 of 330 Revised: 12/16/2010

31 UNF Acid Dilution Tank Exemption EXHIBIT 1 Page 26 of 330 Revised: 12/16/2010

32 UNF Acid Dilution Tank Exemption EXHIBIT 1 Page 27 of 330 Revised: 12/16/2010

33 UNF Acid Dilution Tank Exemption EXHIBIT 1 Page 28 of 330 Revised: 12/16/2010

34 UNF Acid Dilution Tank Exemption EXHIBIT 1 Page 29 of 330 Revised: 12/16/2010

35 UNF Acid Dilution Tank Exemption EXHIBIT 1 Page 30 of 330 Revised: 12/16/2010

36 UNF Acid Dilution Tank Exemption EXHIBIT UNF Building Code Enforcement Program Checklist EXHIBIT 4 Page 31 of 330 Revised: 12/16/2010

37 UNF Acid Dilution Tank Exemption EXHIBIT 1 Page 32 of 330 Revised: 12/16/2010

38 UNF Acid Dilution Tank Exemption EXHIBIT 1 Page 33 of 330 Revised: 12/16/2010

39 UNF Acid Dilution Tank Exemption EXHIBIT 1 Page 34 of 330 Revised: 12/16/2010

40 Project Identification Temporary Project Signage EXHIBIT Project Identification Temporary Project Signage EXHIBIT 1 Page 35 of 330 Revised: 12/16/2010

41 Closeout Procedures Closeout Procedures 1. General A. Related Documents: Drawings and general provisions of the contract, including General and Supplementary Conditions and other Division 1 Specification Sections, apply to this section. B. Summary: This section includes administrative and procedural requirements for contract closeout, including, but not limited to, the following: Inspection procedures. Project Record Documents. Operation and maintenance manuals. Warranties. Instruction of Owner s personnel. Final cleaning. Related sections include the following: Divisions 2 through 16 sections for specific closeout and special cleaning requirements for products of those sections. C. Substantial Completion: Preliminary Procedures: Before requesting inspection for determining date of Substantial Completion, complete the following. List items below that are incomplete in request. Prepare a list of items to be completed and corrected (punch list), the value of items on the list, and reasons why the work is not complete. Advise Owner of pending insurance changeover requirements. Submit specific warranties, workmanship bonds, maintenance service agreements, final certifications, and similar documents. Obtain and submit releases permitting Owner unrestricted use of the work and access to services and utilities. Include occupancy permits, operating certificates, and similar releases. Page 36 of 330 Revised: 12/16/2010

42 Closeout Procedures Prepare and submit Project Record Documents, operation and maintenance manuals, Final Completion construction photographs and photographic negatives, damage or settlement surveys, property surveys, and similar final record information. Deliver tools, spare parts, extra materials, and similar items to location designated by Owner. Label with manufacturer s name and model number where applicable. Make final changeover of permanent locks and deliver keys to Owner. Advise Owner s personnel of changeover in security provisions. Complete startup testing of systems. Submit test/adjust/balance records. Terminate and remove temporary facilities from project site, along with mockups, construction tools, and similar elements. Advise Owner of changeover in heat and other utilities. Submit changeover information related to Owner s occupancy, use, operation, and maintenance. Complete final cleaning requirements, including touchup painting. Touch up and otherwise repair and restore marred exposed finishes to eliminate visual defects. Inspection: Submit a written request for inspection for Substantial Completion. On receipt of request, Architect will either proceed with inspection or notify contractor of unfulfilled requirements. Architect will prepare the Certificate of Substantial Completion after inspection or will notify contractor of items, either on contractor s list or additional items identified by architect, that must be completed or corrected before certificate will be issued. Reinspection: Request reinspection when the work identified in previous inspections as incomplete is completed or corrected. Results of completed inspection will form the basis of requirements for Final Completion. D. Final Completion: Preliminary Procedures: Before requesting final inspection for determining date of Final Completion, complete the following: Page 37 of 330 Revised: 12/16/2010

43 Closeout Procedures Submit a final Application for Payment according to Division 1 section Payment Procedures. Submit certified copy of Architect s Substantial Completion inspection list of items to be completed or corrected (punch list), endorsed and dated by Architect. The certified copy of the list shall state that each item has been completed or otherwise resolved for acceptance. Submit evidence of final, continuing insurance coverage complying with insurance requirements. Instruct Owner s personnel in operation, adjustment, and maintenance of products, equipment and systems. Inspection: Submit a written request for final inspection for acceptance. On receipt of request, architect will either proceed with inspection or notify contractor of unfulfilled requirements. Architect will prepare a final Certificate for Payment after inspection or will notify contractor of construction that must be completed or corrected before certificate will be issued. Reinspection: Request reinspection when the work identified in previous inspections as incomplete is completed or corrected. E. List of Incomplete Items (Punch List) Preparation: Submit three copies of list. Include name and identification of each space and area affected by construction operations for incomplete items and items needing correction including, if necessary, areas disturbed by contractor that are outside the limits of construction. Organize list of spaces in sequential order, starting with exterior areas first. Organize items applying to each space by major element, including categories for ceiling, individual walls, floors, equipment, and building systems. Include the following information at the top of each page: Project Name. Date. Name of Architect. Name of Contractor. Page number. Page 38 of 330 Revised: 12/16/2010

44 Closeout Procedures F. Project Record Documents: Refer to individual project contract requirements. G. Operation and Maintenance Manuals: Refer to Specification Section Operations and Maintenance Data. H. Warranties: Refer to individual project specifications for warranty requirements. 2. Products A. Materials: Cleaning Agents: Use cleaning materials and agents recommended by manufacturer or fabricator of the surface to be cleaned. Do not use cleaning agents that are potentially hazardous to health or property or that might damage finished surfaces. 3. Execution A. Demonstration and Training: Instruction: Instruct Owner s personnel to adjust, operate, and maintain systems, subsystems, and equipment not part of a system. Provide instructors experience in operation and maintenance procedures. Provide instruction at mutually agreed-on times. For equipment that requires seasonal operation, provide similar instruction at the start of each season. Schedule training with Owner with at least seven days advance notice. Coordinate instructors, including providing notification of dates, times, length of instruction, and course content. Provide Owner training for all mechanical, electrical, plumbing, communication systems, operable panel partitions and custodial. Provide this training recorded on a DVD. Video taping shall be done outside of the training class so that it can be scripted and completed without interruption. This video tape training shall answer the following questions about each component and system: What is it? What does it do? How does it do it? Where is the power feed from / Where are the emergency shut-offs and any other pertinent information related to each component and system. Page 39 of 330 Revised: 12/16/2010