Service Pack Release Letter MIC Series 550 System Controller Table of Contents

Size: px

Start display at page:

Download "Service Pack Release Letter MIC Series 550 System Controller 2.12.00.07. Table of Contents"

Margaret Ball
8 years ago
Views:

1 Service Pack Release Letter Table of Contents 1. Introduction Disclaimer of Warranty Purpose Scope Installation Requirements 2 2. About This Service Pack Release 2 3. Hardware Changes 3 4. Software Changes Preset Commands Change to Default Settings Enhancements 4 5. Feature Restrictions 4 6. Uploading Firmware 4 7. History 5 Release Notes Robert Bosch GmbH reserves all rights even in the event of industrial property rights. We reserve all rights of disposal such as copying and passing on to third parties. Last Checked-In: Jan-25

2 Change to Default Settings 3 4.3 Enhancements 4 5. Feature Restrictions 4 6. Uploading Firmware 4 7. History 5 Release Notes 01.

2 Page: 2 of 6 Service Pack Release Letter 1. Introduction 1.1 Disclaimer of Warranty Bosch Security Systems, Inc. makes no representations or warranties, either expressed or implied, by or with respect to anything in this document, and shall not be liable for any implied warranties of merchantability or fitness for a particular purpose or for any indirect, special or consequential damages. 1.2 Purpose The purpose of the Service Pack Release Letter document is to communicate major new features and changes in this release of the product. It also documents component compatibility, workarounds, and any feature restrictions. 1.3 Scope This document describes the Service Pack release which includes the following components: Component Version MIC550Main.G4i FPGA_MIC_SC_Biphase_550.G4i Installation Requirements Before installing the MIC550Main.G4i (version ) you must check the version of the FPGA currently on your MIC 550. If the version of the FPGA on the MIC 550 is release 2.02 or earlier, you must first update the FPGA using the FPGA_MIC_SC_Biphase_550.G4i file before updating the system controller with the MIC55Main.G4i file. To check the FPGA version: 1. Issue the AUX 66 ON command from a keyboard or other control device connected to the MIC 550. This command displays the initial firmware version screen on a monitor connected to the MIC While the initial firmware version screen is visible, issue the AUX 66 ON command a second time to expand the list of firmware installed on the MIC Note the release version of the FPGA. If the version of the FPGA is 2.02 or earlier you must install the FPGA_MIC_SC_Biphase_550.G4i file before updating the system controller. It is recommended to extract both files in this service pack to the same directory and to use the Configuration Tool for Imaging Devices to upload both files to the camera. 2. About This Service Pack Release This is an Engineering Release of the firmware components identified section 1.3.

for a particular purpose or for any indirect, special or consequential damages. 1.

3 Page: 3 of 6 3. Hardware Changes None. 4. Software Changes 4.1 Preset Commands The following table lists the special preset commands that the MIC 550 using the Forward Vision protocol now supports: Preset: 1 Preset: 62 Preset: 85 Preset: 86 Preset: 87 Preset: 88 Preset: 89 Preset: 90 Preset: 91 Preset: 92 Preset: 98 Preset: 99 Preset: 198 Preset: 199 Preset: 204 Preset: 205 Preset: 206 Preset: 207 Preset: 208 Preset: 209 Preset: 210 Preset: 215 Preset: 217 Preset: 218 Preset: 219 Preset: 220 Preset: 232 Preset: 233 Preset: 251 Preset: 255 Auto Home Position Wash Wipe Position On Screen menu Self Diagnosis Play Pattern One Stop Pattern One Record Pattern One Play Pattern Two Stop Pattern Two Record Pattern Two Find End Stops Show Boot Message Intermittent Wipe On Intermittent Wipe Off Auto Home to Preset Auto Home to Tour Auto Home Off Multi Alarms Enable Multi Alarms Disable Digital Zoom Disable Digital Zoom Enable Auto Home to Pattern Auto Flip On Auto Flip Off Wash Wipe Enable Wash Wipe Disable Privacy: Replace All Privacy: Uncover All Recalibrate Camera Module Load Factory Defaults 4.2 Change to Default Settings The following values have changed to improve the default image quality.: White Balance: ATW (was Extended ATW) Sharpness: 8 (was 12)

88 Preset: 89 Preset: 90 Preset: 91 Preset: 92 Preset: 98 Preset: 99 Preset: 198 Preset: 199 Preset: 204 Preset: 205 Preset: 206 Preset: 207 Preset: 208 Preset: 209 Preset: 210 Preset: 215 Preset:

4 4.3 Enhancements Page: 4 of 6 This section identifies enhancements and defect resolutions provided in the current Service Pack for the MIC Series 550. The following ENHANCEMENTS have been resolved for this delivery. Change Request IMC IMC Description Implemented special preset commands for Forward Vision protocol (refer to section 4.1) Changed default settings for White Balance and Sharpness (refer to section 4.2) Module MIC550Main.G4i MIC550Main.G4i The following DEFECTS have been resolved for this delivery. Change Description Module Request IMC Improved noise reduction. MIC550Main.G4i IMC IMC Activated Input 8 as a valid input for Alarm Rules. MIC550Main.G4i 5. Feature Restrictions None. 6. Uploading Firmware Refer to the AutoDome 100/600/700/800 and MIC 550 Firmware Update Manual, available on the Bosch Security Systems Web site.

1) Changed default settings for White Balance and Sharpness (refer to section 4.2) Module MIC550Main.G4i MIC550Main.G4i The following DEFECTS have been resolved for this delivery.

5 Page: 5 of 6 7. History The following files have been updated in past Service Pack releases Component Version MICMain.G4i MICMain.G4i The following ENHANCEMENTS have been implemented in past Service Pack releases. Change Request Description Service Pack IMC Update to FPGA code for PTZ control. FPGA_MIC_SC_Bi phase_550.g4i IMC Improves sharpness on video image. MIC550Main.G4i IMC Users can now remap Pelco Auxiliary commands 1 through 8. This MIC550Main.G4i enhancement adds the Aux Setup submenu below the Competitive Protocol menu. IMC Support for enhanced noise reduction. This enhancement adds the MIC550Main.G4i following items to the Camera menu: Noise Reduction and Noise Reduction Level IMC Support Forward Vision (FV) protocol. MICMain.G4i Support for Pelco D Absolute Position Commands MICMain.G4i IMC FV: Implement "L" command (Go To Preset) MICMain.G4i IMC FV: Implement "W" command (Reset) MICMain.G4i IMC Send Bicom events to the OSRD serial port MICMain.G4i IMC Add Bicom Event for Wiper operation MICMain.G4i IMC FV: Implement "M" command (Learn Preset), Normal presets only MICMain.G4i IMC FV: Implement "G" command (Set Manual Control) MICMain.G4i IMC FV: Implement "w" command (Set Manual Control with Proportional MICMain.G4i Zoom) IMC FV: Implement "s" command (Set Address) MICMain.G4i IMC FV: Implement "R" command (Setup Preset Tour) MICMain.G4i IMC FV: Implement "T" command (Start\Stop Preset Tour) MICMain.G4i IMC Pelco D "Query Type" command now provides response message MICMain.G4i IMC FV: Implement "N" command (Go To Position) MICMain.G4i IMC FV: Implement "O" command (Get Position) MICMain.G4i IMC FV: Implement "a" command (Get Config) MICMain.G4i IMC FV: Implement "q" command (Set Config) MICMain.G4i IMC FV: Implement "K" command (Emergency Stop) MICMain.G4i IMC FV: Implement "Y" command (Get Software Version) MICMain.G4i IMC FV: Add ability to use Bosch camera menu MICMain.G4i IMC FV: Implement "H" command (Get Manual Control and Alarm Status) MICMain.G4i IMC FV: Implement "~" command (Get MIC Statistics) MICMain.G4i

FPGA_MIC_SC_Bi phase_550.g4i IMC00004096 Improves sharpness on video image. MIC550Main.G4i IMC00003685 Users can now remap Pelco Auxiliary commands 1 through 8. This MIC550Main.

6 Page: 6 of 6 The following DEFECTS have been resolved in past Service Pack releases. Change Description Service Pack Request IMC Corrects issue with wash/wipe behavior if the was position is not predefined. MIC550Main.G4i IMC Corrects issue with fast address using the Forward Vision protocol. MIC550Main.G4i IMC Improve Bicom Commands MICMain.G4i IMC Alarm Menus Restore Defaults option no longer restores defaults for whole MICMain.G4i device IMC Improve Data migration of privacy masks via Bilinx MICMain.G4i IMC Scene departed event was not firing for wash/wipe MICMain.G4i IMC Alarm > Alarm Rules > 'Output Option' Transmit > 'Output period' would MICMain.G4i not activate. IMC Alarm Output Options > Type 'None' cannot be set again when another MICMain.G4i 'Type' was set before IMC Some of the alarm options could not be uploaded to CTFID MICMain.G4i IMC Adjust night mode threshold default value MICMain.G4i IMC Incorrect Alarm Output type provided to CTFID MICMain.G4i IMC Switching between Bosch and FV protocols improved MICMain.G4i IMC Prevent False Motion Alarms if "Wiper/Washer" is started MICMain.G4i IMC FV - N command: Sending max pan at max pan position caused 360 degree MICMain.G4i pan IMC FV: Modify the speed conversion algorithm in G-command MICMain.G4i IMC False Alarms were triggered When Alarm Input state is selected as N.C as MICMain.G4i default state. IMC Scene 1 Inactivity did not work after pan/tilt moving MICMain.G4i IMC Alarm Rules could only be executed once MICMain.G4i IMC Wash-wipe now functional in FV protocol MICMain.G4i IMC Pelco D: Above the horizon tilt positions now points to the upper tilt limit MICMain.G4i

G4i IMC00003772 Corrects issue with fast address using the Forward Vision protocol. MIC550Main.G4i IMC00002902 Improve Bicom Commands MICMain.

Firmware Release Letter BVIP Firmware 5.52. Table of Contents. 1. Introduction 2 1.1 Disclaimer of Warranty 2 1.2 Purpose 2 1.

Firmware Release Letter BVIP Firmware 5.52 Table of Contents 1. Introduction 2 1.1 Disclaimer of Warranty 2 1.2 Purpose 2 1.3 Scope 2 2. About This Service Pack Release 2 3. Hardware s 2 4. Software s