TSX ETZ Configuration of your computer for TSX ETZ direct connection by serial link. Eng V1.0
|
|
|
- Claribel Leonard
- 8 years ago
- Views:
Transcription
1 TSX ETZ Configuration of your computer for TSX ETZ direct connection by serial link Eng V1.0
2 2
3 Table of Contents About the book Chapter 1 Configuration and connection for Windows At a Glance Configuration of the computer Configuration of the direct cable connection Connection to the TSX ETZ Module with null modem Chapter 2 Configuration and connection for Windows At a Glance Configuration of the computer Configuration of the direct cable connection Connection to the TSX ETZ Module with null modem Chapter 3 Configuration and connection for Windows At a Glance Configuration of the computer Configuration of the Dial-Up Networking Connection to the TSX ETZ Module with null modem Chapter 4 Configuration and connection for Windows NT At a Glance Configuration of the computer Configuration of the Dial-Up Networking Connection to the TSX ETZ Module with null modem Chapter 5 Configuration and connection for Windows Millennium At a Glance Configuration of the computer Configuration of the direct cable connection Connection to the TSX ETZ Module with null modem Chapter 6 Connection problems Connection problems
4 4
5 About the book At a Glance Document Scope This manual contains examples of your computer configuration in order to access the TSX ETZ Module http server using its serial link. Revision History Rev. No. Changes 1 Initial version. User Comments We welcome your comments about this document. You can reach us by at TECHCOMM@modicon.com 5
6 About the book 6
7 Configuration and connection for Windows 95 1 At a Glance Presentation What s in this Chapter? This non-exhaustive document is an example of your computer configuration in order to access the TSX ETZ Module http server using its serial link. Although reasonable care has been taken to provide accurate and authoritative information in this document, no responsibility is assumed by Schneider Automation for any consequences arising from the use of this document. This Chapter contains the following Maps: Topic Page Configuration of the computer 8 Configuration of the direct cable connection 14 Connection to the TSX ETZ Module with null modem 22 7
8 Configuration and connection for Windows 95 Configuration of the computer Presentation Click on "Start", point to "Settings", and then click on "Control Panel". The following dialog box is displayed: Double click on "Add / Remove Programs": in the menu "Add / Remove Programs Properties", click on the tab "Windows Setup". 8
9 Configuration and connection for Windows 95 The following dialog box is displayed: Select "Communications" and then click on "Details". 9
10 Configuration and connection for Windows 95 The following dialog box displayed: Add the components "Dial-Up Networking" and "Direct Cable Connection". Then click on "OK". 10
11 Configuration and connection for Windows 95 The following dialog box displayed: Insert the Windows 95 CD-ROM if needed and then click on "OK" to validate the component "Communications". 11
12 Configuration and connection for Windows 95 If the computer is not identified by the network component, you must follow these 2 steps: 1. The dialog box is diplayed: Click on "OK". The dialog box "Network" is displayed: 12
13 Configuration and connection for Windows In the tab identification, type the "Computer name" and the "Workgroup". Click on "Close". Then, Window installs different files on this directory: Click on "OK" to restart your computer. 13
14 Configuration and connection for Windows 95 Configuration of the direct cable connection Presentation Click on "Start", point to "Programs -> Accessories", and then click on "Direct Cable Connection". The following dialog box is displayed: Check "Guest" and click on "Next". 14
15 Configuration and connection for Windows 95 The following dialog box is displayed: Select the serial port you want to use and click on "Next". Note: The example is given with the communication port COM1. You can select either COM1 or another serial port on your computer. 15
16 Configuration and connection for Windows 95 The following dialog box is displayed: Click on "Finish" to complete set up. Click on "Close". Before connecting, you must modify "Serial COM1" settings. Note: If the connection is not closed fast enough, the user may get the message "Cannot connect to host". 16
17 Configuration and connection for Windows 95 Click on "Start", point to "Settings", and then click on "Control Panel". In the dialog box "Control Panel", double click on "System" icon. The dialog box "System Properties" is displayed: In the menu "System properties", select the tab "Device manager": click on "modem" and select "Serial cable on COM1". Then click on "Properties". 17
18 Configuration and connection for Windows 95 The dialog box "Serial cable on COM1 Properties" is displayed: In the tab "Modem", select the communication port you want to use and the speed (57600 bits per second). Then click on "OK" to get back to the dialog box "System Properties": 18
19 Configuration and connection for Windows 95 In the tab "Device Manager": click on "Ports (COM & LPT)" and select "Communications Port (COM1)". Click on "Properties". 19
20 Configuration and connection for Windows 95 Click on the tab "Port Settings" to adjust the speed at bits per second, 8 data bits, parity: None, 1 stop bit, Flow control: None, then click on "OK". Click "OK" in the dialog box "System Properties" to complete the set up. Then close the "Control Panel" dialog box. 20
21 Configuration and connection for Windows 95 Procedure to install TCP/IP Protocol on your computer Direct Cable Connection may not work if you are using Dial up Networking with only the Net BEUI Protocol installed. You have then to install the TCP/IP Protocol on your computer. Steps to follow: Step Action 1 Click the Start button, point to Settings and click Control Panel. 2 Double-click the Network icon. 3 Click the Add button. 4 Click Protocol, then click the Add button. 5 Click Microsoft. 6 Click TCP/IP Protocol. 7 Click the OK button. You must restart your computer before the new settings will take effect. 21
22 Configuration and connection for Windows 95 Connection to the TSX ETZ Module with null modem Presentation First, connect the null modem between the computer and the TSX ETZ Module. Click on "Start", point to "Programs -> Accesories" and then click on "Direct Cable Connection". The following dialog box is displayed: Click on "Connect", then the following dialog box is displayed: The connection may take several seconds. 22
23 Configuration and connection for Windows 95 Then, the dialog box is displayed: Click on "Cancel" in the dialog box "Direct Cable Connection Host". Then the following dialog box is displayed: You are currently connected to the TSX ETZ Module. Open your internet browser with the IP Address in order to access TSX ETZ http server. Refer to the "TSX ETZ User Manual" to set up password, configure and diagnose TSX ETZ Module. To shut down the connection, just click on "Close". 23
24 Configuration and connection for Windows 95 24
25 Configuration and connection for Windows 98 2 At a Glance Presentation What s in this Chapter? This non-exhaustive document is an example of your computer configuration in order to access the TSX ETZ Module http server using its serial link. Although reasonable care has been taken to provide accurate and authoritative information in this document, no responsibility is assumed by Schneider Automation for any consequences arising from the use of this document. This Chapter contains the following Maps: Topic Page Configuration of the computer 26 Configuration of the direct cable connection 30 Connection to the TSX ETZ Module with null modem 37 25
26 Configuration and connection for Windows 98 Configuration of the computer Presentation Click on "Start", point to "Settings", and then click on "Control Panel". The following dialog box is displayed: Double click on "Add / Remove Programs": in the menu "Add / Remove Programs Properties", click on the tab "Windows Setup". 26
27 Configuration and connection for Windows 98 The following dialog box is displayed: Select "Communications" and then click on "Details". 27
28 Configuration and connection for Windows 98 The following dialog box displayed: Add the components "Dial-Up Networking" and "Direct Cable Connection". Then click on "OK". 28
29 Configuration and connection for Windows 98 The following dialog box displayed: Insert the Windows 98 CD-ROM if needed and then click on "OK" to validate the component "Communications". Click on "OK" to restart your computer. 29
30 Configuration and connection for Windows 98 Configuration of the direct cable connection Presentation Click on "Start", point to "Programs -> Accessories -> Communications", and then click on "Direct Cable Connection". The following dialog box is displayed: Check "Guest" and click on "Next". 30
31 Configuration and connection for Windows 98 The following dialog box is displayed: Select the serial port you want to use and click on "Next". Note: The example is given with the communication port COM1. You can select either COM1 or another serial port on your computer. 31
32 Configuration and connection for Windows 98 The following dialog box is displayed: Click on "Finish" to complete set up. Click on "Close". Before connecting, you must modify "Serial COM1" settings. Note: If the connection is not closed fast enough, the user may get the message "Cannot connect to host". 32
33 Configuration and connection for Windows 98 Click on "Start", point to "Settings", and then click on "Control Panel". In the dialog box "Control Panel", double click on "System" icon. The dialog box "System Properties" is displayed: In the menu "System Properties", select the tab "Device Manager": click on "Modem" and select "Serial cable on COM1". Then click on "Properties". 33
34 Configuration and connection for Windows 98 The dialog box "Serial cable on COM1 Properties" is displayed: In the tab "Modem", select the communication port you want to use and the speed (57600 bits per second). Then click on "OK" to get back to the dialog box "System Properties": 34
35 Configuration and connection for Windows 98 In the tab "Device Manager": click on "Ports (COM & LPT)" and select "Communications Port (COM1)". Click on "Properties". 35
36 Configuration and connection for Windows 98 Click on the tab "Port Settings" to adjust the speed at bits per second, 8 data bits, parity: None, 1 stop bit, Flow control: None, then click on "OK". Click "OK" in the dialog box "System Properties" to complete the set up. Then close the "Control Panel" dialog box. You must restart your computer before the new settings will take effect. 36
37 Configuration and connection for Windows 98 Connection to the TSX ETZ Module with null modem Presentation First, connect the null modem between the computer and the TSX ETZ Module. Click on "Start", point to "Programs -> Accesories -> Communications" and then click on "Direct Cable Connection". The following dialog box is displayed: Click on "Connect", then the following dialog box is displayed: The connection may take several seconds. 37
38 Configuration and connection for Windows 98 Then, the dialog box is displayed: Click on "Cancel" in the dialog box "Direct Cable Connection Host". Then the following dialog box is displayed: You are currently connected to the TSX ETZ Module. Open your internet browser with the IP Address in order to access TSX ETZ http server. Refer to the "TSX ETZ User Manual" to set up password, configure and diagnose TSX ETZ Module. To shut down the connection, just click on "Close". 38
39 Configuration and connection for Windows At a Glance Presentation What s in this Chapter? This non-exhaustive document is an example of your computer configuration in order to access the TSX ETZ Module http server using its serial link. Although reasonable care has been taken to provide accurate and authoritative information in this document, no responsibility is assumed by Schneider Automation for any consequences arising from the use of this document. This Chapter contains the following Maps: Topic Page Configuration of the computer 40 Configuration of the Dial-Up Networking 46 Connection to the TSX ETZ Module with null modem 61 39
40 Configuration and connection for Windows 2000 Configuration of the computer Presentation Click on "Start", point to "Settings", and then click on "Control Panel". The following dialog box is displayed: 40
41 Configuration and connection for Windows 2000 Double click on the "System" icon: On the tab "Hardware": click on "Device Manager". 41
42 Configuration and connection for Windows 2000 Click on "Port (COM & LPT)" and then double click on "Communications Port (COM1)". 42
43 Configuration and connection for Windows 2000 Click on the tab "Port Settings" to adjust the speed at bits per second, 8 data bits, parity: None, 1stop bit, Flow control: None. Then click "OK". 43
44 Configuration and connection for Windows 2000 Back to the menu "Device Manager": click on "Modem" and then double click on "Communications cable between two computers". 44
45 Configuration and connection for Windows 2000 The dialog box "Communications cable between two computers Properties" is displayed: Select the maximum speed (57600 bits per second). Then click on "OK" to get back to the dialog box "Device Manager": close this dialog box and click on "OK" in the dialog box "System Properties": 45
46 Configuration and connection for Windows 2000 Configuration of the Dial-Up Networking Presentation Click on "Start", point to "Settings", and then click on "Control Panel": Double click on the "Network and Dial-up Connections" icon. 46
47 Configuration and connection for Windows 2000 The following dialog box is displayed: Double click on "Make New Connection" icon. 47
48 Configuration and connection for Windows 2000 The dialog box "Location Information" may be displayed: Fill the area code and the phone number and then click "OK". Then, click on "OK" in the dialog box "Phone and Modem Options". 48
49 Configuration and connection for Windows 2000 The "Network Connection Wizard" dialog box is displayed: Click on "Next". 49
50 Configuration and connection for Windows 2000 The following dialog box is displayed: Select "Connet directly to another computer" and then click on "Next". 50
51 Configuration and connection for Windows 2000 Check "Guest" and click on "Next". 51
52 Configuration and connection for Windows 2000 Note: The example is given with the communication port COM1. You can select either COM1 or another serial port on your computer. Select the communication port you want to use for Direct Cable Connection and click "Next". 52
53 Configuration and connection for Windows 2000 Select if you want to make the connection available for "all users" or only for "you" and then click on "Next". 53
54 Configuration and connection for Windows 2000 Type the name of the connection for TSX ETZ Module and click on "Finish". 54
55 Configuration and connection for Windows 2000 In the connection dialog box "Connect ETZ Direct Connection": Type "User name" and "Password" corresponding to the TSX http Server (Default values on the TSX ETZ are USER for User name and USER for Password). Then click on "Properties" to configure the connection: 55
56 Configuration and connection for Windows 2000 In the menu "General", select the communication port used: serial port COM1 here. Once the device selected, click on "Configure" in the same dialog box. 56
57 Configuration and connection for Windows 2000 Then, the dialog box is displayed: Adjust the maximum speed at bits per second. Check Parameters as described above and then click on "OK". 57
58 Configuration and connection for Windows 2000 The configuration dialog box is displayed again: Select the menu "Networking". 58
59 Configuration and connection for Windows 2000 The "ETZ Direct Connection" dialog box is displayed: Select the dial-up server "PPP for windows 95/98/2000/NT4, Internet " and the Network protocol "TCP/IP". Click then on "OK". 59
60 Configuration and connection for Windows 2000 The connection dialog box is displayed again: The set up of the Direct Cable Connection is now complete, even if you close the previous dialog box. 60
61 Configuration and connection for Windows 2000 Connection to the TSX ETZ Module with null modem Presentation First, connect the null modem between the computer and the TSX ETZ Module. Click on "Start", point to "Settings -> Network and Dial-up Connection" and then click on "Connect ETZ Direct Connection". The "Connect ETZ Direct Connection" dialog box is displayed: 61
62 Configuration and connection for Windows 2000 Click on "Connect": two dialog boxes are displayed: You are then connected to the TSX ETZ Module. Open your internet browser with the IP Address in order to access TSX ETZ http server. Refer to the "TSX ETZ User Manual" to set up password, configure and diagnose TSX ETZ Module. To shut down the connection or check the status of the connection, right click its icon in the network connections folder, or click its icon on the taskbar (if present). 62
63 Configuration and connection for Windows NT4 4 At a Glance Presentation What s in this Chapter? This non-exhaustive document is an example of your computer configuration in order to access the TSX ETZ Module http server using its serial link. Although reasonable care has been taken to provide accurate and authoritative information in this document, no responsibility is assumed by Schneider Automation for any consequences arising from the use of this document. This Chapter contains the following Maps: Topic Page Configuration of the computer 64 Configuration of the Dial-Up Networking 74 Connection to the TSX ETZ Module with null modem 80 63
64 Configuration and connection for Windows NT4 Configuration of the computer Presentation Click on "Start", point to "Settings", and then click on "Control Panel". Double click on "Modems" icon. The following dialog box is displayed: Check "Don t detect my modem; I will select it from a list", and then click on "Next". 64
65 Configuration and connection for Windows NT4 The following dialog box is displayed: Select "(Standard Modem Types)" and "Dial-Up Networking Serial Cable between 2 PCs", and then click on "Next". 65
66 Configuration and connection for Windows NT4 Note: The example is given with the communication port COM1. You can select either COM1 or another serial port on your computer. Select on which port you want to install the direct cable connection and then click on "Next". 66
67 Configuration and connection for Windows NT4 Click on "Finish". 67
68 Configuration and connection for Windows NT4 The following dialog box is diplayed: Select "Dial-Up Networking Serial Cable between 2 PCs" and click on "Properties". 68
69 Configuration and connection for Windows NT4 Adjust the "Maximum speed" at bits per second, and click on "OK". 69
70 Configuration and connection for Windows NT4 Click on "Close". Click on "Yes". 70
71 Configuration and connection for Windows NT4 The dialog box "Remote Access Setup" is displayed: After selecting the communication port, click on "Configure": Select "Dial out only" and then click "OK". 71
72 Configuration and connection for Windows NT4 The dialog box "Remote Access Setup" is displayed again: Select "Network": Check "TCP/IP" and click "OK": 72
73 Configuration and connection for Windows NT4 The dialog box "Remote Access Setup" is displayed again. Click on "Continue". After a few seconds, the dialog box is displayed: Click on "Yes" to restart your computer. The set up of the Direct Cable Connection is complete. 73
74 Configuration and connection for Windows NT4 Configuration of the Dial-Up Networking Presentation Click on "Start", point to "Programs -> Accessories", and then click on "Dial-Up Networking". The following dialog box is displayed: Click on "New...". 74
75 Configuration and connection for Windows NT4 The dialog box "New Phonebook Entry" is displayed: Enter the "Entry Name", and deselect "Use another port if busy". Then click on "Configure": Set up speed at "57600" bits per second, and deselect icons as shown in this dialog box. Then click on "OK". 75
76 Configuration and connection for Windows NT4 In the dialog box "New Phonebook Entry": click on tab "Server". Select "PPP: Windows NT..." for dial-up server type, check "TCP/IP" for the network protocol, "Enable PPP LCP extensions", and then click on "TCP/IP Settings...": 76
77 Configuration and connection for Windows NT4 Check Parameters as described above and then click on "OK". 77
78 Configuration and connection for Windows NT4 In the dialog box "New Phonebook Entry", select the tab "Security": Check "Accept any authentication including clear text", and then click on "OK": 78
79 Configuration and connection for Windows NT4 The set-up of the connection "ETZ" is complete and saved in the Phonebook. 79
80 Configuration and connection for Windows NT4 Connection to the TSX ETZ Module with null modem Presentation First, connect the null modem between the computer and the TSX ETZ Module. Click on "Start", point to "Programs -> Accesories" and then click on "Dial-Up Networking". The following dialog box is displayed: Select the "Phonebook Entry"corresponding to TSX ETZ and click on "Dial" to establish the connection. 80
81 Configuration and connection for Windows NT4 Type "User name" and "Password" corresponding to the TSX ETZ http Server (Default values on the TSX ETZ are USER for User name and USER for Password). Note: This information is requested only for a modem connection. The "domain" field must remain empty. Then, click on "OK". 81
82 Configuration and connection for Windows NT4 Once connected, the dialog box is displayed: Click on "OK". Open your internet browser with the IP Address in order to access TSX ETZ http server. Refer to the "TSX ETZ User Manual" to set up password, configure and diagnose TSX ETZ Module. To shut down the connection, click on "Hang up" and "Close" in the dialog box "Dial-Up Networking Monitor. 82
83 Configuration and connection for Windows Millennium 5 At a Glance Presentation What s in this Chapter? This non-exhaustive document is an example of your computer configuration in order to access the TSX ETZ Module http server using its serial link. Although reasonable care has been taken to provide accurate and authoritative information in this document, no responsibility is assumed by Schneider Automation for any consequences arising from the use of this document. This Chapter contains the following Maps: Topic Page Configuration of the computer 84 Configuration of the direct cable connection 88 Connection to the TSX ETZ Module with null modem 95 83
84 Configuration and connection for Windows Millennium Configuration of the computer Presentation Click on "Start", point to "Settings", and then click on "Control Panel". The following dialog box is displayed: Double click on "Add / Remove Programs": in the menu "Add / Remove Programs Properties", click on the tab "Windows Setup". 84
85 Configuration and connection for Windows Millennium The following dialog box is displayed: Select "Communications" and then click on "Details". 85
86 Configuration and connection for Windows Millennium The following dialog box displayed: Add the components "Dial-Up Networking" and "Direct Cable Connection". Then click on "OK". 86
87 Configuration and connection for Windows Millennium The following dialog box displayed: Insert the Windows Millennium CD-ROM if needed and then click on "OK" to validate the component "Communications". 87
88 Configuration and connection for Windows Millennium Configuration of the direct cable connection Presentation Click on "Start", point to "Programs -> Accessories -> Communications", and then click on "Direct Cable Connection". The following dialog box is displayed: Check "Guest" and click on "Next": 88
89 Configuration and connection for Windows Millennium Select the serial port you want to use and click on "Next". Note: The example is given with the communication port COM1. You can select either COM1 or another serial port on your computer. 89
90 Configuration and connection for Windows Millennium The following dialog box is displayed: Click on "Finish" to complete set up. Click on "Close". Before connecting, you have change parameters for serial cable COM1. Note: If the connection is not closed fast enough, the user may get the message "Cannot connect to host". 90
91 Configuration and connection for Windows Millennium Click on "Start", point to "Settings", and then click on "Control Panel". In the dialog box "Control Panel", double click on "System" icon. The dialog box "System Properties" is displayed: In the menu "System properties", select the tab "Device manager": click on "modem" and select "Serial cable on COM1". Then click on "Properties": the dialog box "Serial cable on COM1 Properties" is displayed: 91
92 Configuration and connection for Windows Millennium In the tab "Modem", select the communication port you want to use and the speed (57600 bits per second). Then click on "OK" to get back to the dialog box "System Properties": 92
93 Configuration and connection for Windows Millennium In the tab "Device Manager": click on "Ports (COM & LPT)" and select "Communications Port (COM1)". Click on "Properties". 93
94 Configuration and connection for Windows Millennium Click on the tab "Port Settings" to adjust the speed at bits per second, 8 data bits, parity: None, 1 stop bit, Flow control: None, then click on "OK". Click "OK" in the dialog box "System Properties" to complete the set up. Then close the "Control Panel" dialog box. You must restart your computer before the new settings will take effect. 94
95 Configuration and connection for Windows Millennium Connection to the TSX ETZ Module with null modem Presentation First, connect the null modem between the computer and the TSX ETZ Module. Click on "Start", point to "Programs -> Accesories -> Communications" and then click on "Direct cable connection", the following dialog box is displayed: Click on "Connect". Then the following dialog box is displayed: The connection has been made between the computer and the TSX ETZ. Open your internet browser with the IP Address in order to access TSX ETZ http server. Refer to the "TSX ETZ User Manual" to set up password, configure and diagnose TSX ETZ Module. To shut down the connection, just click on "Close". 95
96 Configuration and connection for Windows Millennium 96
97 Connection problems 6 Connection problems Procedure It may be due to several causes: Step Action 1 Verify that your computer is connected to the TSX ETZ with a null modem cable. 2 You must verify your serial port settings (speed at bits per second...). 3 Ensure that the Internet protocol TCP/IP is installed on your computer. If not, please refer to the documentation provided with Windows
98 Connection problems Step Action 4 In certain cases, the connection may not work if the FIFO Buffers are not activated. To access this dialog box, click on "Start", point to "Settings" and click on "Control Panel": For Windows 95, 98 and Millennium: l Click on "System" icon. l In the tab "Device Manager", click on "Ports (COM & LPT)" and select "Communications Port (COM1)". Click on "Properties". l Click on the tab "Port Settings" on the dialog box "Communications Port (COM1) Properties". l In the tab "Port Settings", click on "Advanced". l Select the "Use FIFO Buffers" and click "OK" to validate the new settings. For Windows NT4: l Click on "Ports" icon. l Then click on "Settings". l Click on "Advanced". l Select the "FIFO Enabled" and click "OK" to validate the new settings. For Windows 2000: l Click on "System". l In the tab "Hardware", click on "Device Manager". l Then click on "Ports (COM & LPT)" and double click on "Communications Port (COM1)". l In the tab "Port Settings", click on "Advanced". l Select the "Use FIFO Buffers" and click "OK" to validate the new settings. Note: Nevertheless, if you encounter any other problem with the configuration of your direct cable, you can also refer to Microsoft support at: " 98
Palomar College Dial-up Remote Access
Palomar College Dial-up Remote Access Instructions for Windows 95/98 and Windows 2000 Following are instructions to implement dialup access to the Palomar College network, email and Internet. The minimum
Connecting and Setting Up Your Laptop Computer
CHAPTER 3 Connecting and Setting Up Your Laptop Computer This chapter explains how to connect your laptop to the Cisco Unified MeetingPlace system and how to set up your laptop so that you can use HyperTerminal.
Installing the Microsoft Network Driver Interface
Installing the Microsoft Network Driver Interface Overview This guide explains how to install the PictureTel Live200 Microsoft Network Driver Interface (NDIS) software you have downloaded from PictureTel's
MODEM AND DIAL-UP. Installation/Configuration (Windows 95/98/Me/NT/2000/XP)
MODEM AND DIAL-UP Installation/Configuration (Windows 95/98/Me/NT/2000/XP) Iridium Satellite LLC 1 February 22, 2006 --------------------------------------------------------------------------------------------------------------------------------------------TABLE
Metasys System Direct Connection and Dial-Up Connection Application Note
Metasys System Direct Connection and Dial-Up Connection Application Note Code No. LIT-1201639 Software Release 5.1 Issued August 27, 2013 Supersedes October 4 2010 Refer to the QuickLIT website for the
LPR for Windows 95/98/Me/2000/XP TCP/IP Printing User s Guide. Rev. 03 (November, 2001)
LPR for Windows 95/98/Me/2000/XP TCP/IP Printing User s Guide Rev. 03 (November, 2001) Copyright Statement Trademarks Copyright 1997 No part of this publication may be reproduced in any form or by any
Immotec Systems, Inc. SQL Server 2005 Installation Document
SQL Server Installation Guide 1. From the Visor 360 installation CD\USB Key, open the Access folder and install the Access Database Engine. 2. Open Visor 360 V2.0 folder and double click on Setup. Visor
Operating Instructions
Operating Instructions (For Setting Up) Digital Imaging Systems Installation Overview Model No. DP-8060 / 8045 / 8035 Table of Contents Setting Your Machine Installation Overview General Installation Overview...
Operating Instructions
Operating Instructions (For Setting up the Printer Driver and the Panasonic Document Management System) Digital Imaging Systems Model No. DP-800P / 800E / 806P Installation Table of Contents Installation
Omni 56K USB Lite Quick Start Guide
Omni 56K USB Lite Quick Start Guide ZyXEL TOTAL INTERNET ACCESS SOLUTION 1. Hardware Installation Connect your modem to your analog phone or fax. Use the phone cord included to connect to the phone jack
USER GUIDE. Ethernet Configuration Guide (Lantronix) P/N: 2900-300321 Rev 6
KRAMER ELECTRONICS LTD. USER GUIDE Ethernet Configuration Guide (Lantronix) P/N: 2900-300321 Rev 6 Contents 1 Connecting to the Kramer Device via the Ethernet Port 1 1.1 Connecting the Ethernet Port Directly
Chapter7 Setting the Receiving PC for Direct Upload. Setting the Receiving PC for Direct Upload... 148 For Windows... 148 For Macintosh...
Chapter7 Setting the Receiving PC for Direct Upload Setting the Receiving PC for Direct Upload... 148 For Windows... 148 For Macintosh... 153 Setting the Receiving PC for Direct Upload This section explains
DIAL-UP DATA. User s Guide
DIAL-UP DATA User s Guide Iridium Satellite LLC Rev. 5; January 1, 2003 DIAL-UP DATA SERVICE--------------------------------------------------------------------------------------- TABLE OF CONTENTS 1 Dial-Up
Connecting to Bruin OnLine Using Windows 95/98/ME
Connecting to Bruin OnLine Using Windows 95/98/ME (Manual Setup Method) Completion Time Estimate: 25 Minutes These are the instructions for manually setting up Dial-Up Networking for use with Bruin OnLine.
DIAL-UP DATA. User s Guide
DIAL-UP DATA User s Guide Iridium Satellite LLC Rev. 2; June 15, 2001 DIAL-UP DATA SERVICE--------------------------------------------------------------------------------------- TABLE OF CONTENTS 1 Dial-Up
Prestige 314 Read Me First
Prestige 314 Read Me First Console WAN 10M PORT Prestige Rear Panel Connections CONNECTION Use an RS-232 console cable. Use the cable that came with your broadband modem. LAN 10/100M Port Number COMPUTER
Connecting the DG-102S VoIP Gateway to your network
Contents of Package: DG-102S VoIP Station Gateway Power adapter CD-ROM, including User s Manual Quick Install Guide Requirements: RS-232 Console Cable Two RJ-45 CAT-5 Straight-Through Cables For more information
DP-313 Wireless Print Server
DP-313 Wireless Print Server Quick Installation Guide TCP/IP Printing (LPR for Windows 95/98/Me/2000) Rev. 03 (August, 2001) Copyright Statement Trademarks Copyright 1997 No part of this publication may
How to setup a VPN on Windows XP in Safari.
How to setup a VPN on Windows XP in Safari. If you want to configure a VPN connection from a Windows XP client computer you only need what comes with the Operating System itself, it's all built right in.
AC500. Software Description. Scalable PLC for Individual Automation. Installation of the AC500 Control Builder PS501
Software Description AC500 Scalable PLC for Individual Automation Installation of the AC500 Control Builder PS501 CM572 PM581 DC532 AX522 Contents Installation of the AC500 Control Builder 1 Contents
Setup and Configuration Guide for Pathways Mobile Estimating
Setup and Configuration Guide for Pathways Mobile Estimating Setup and Configuration Guide for Pathways Mobile Estimating Copyright 2008 by CCC Information Services Inc. All rights reserved. No part of
IIS, FTP Server and Windows
IIS, FTP Server and Windows The Objective: To setup, configure and test FTP server. Requirement: Any version of the Windows 2000 Server. FTP Windows s component. Internet Information Services, IIS. Steps:
SQL EXPRESS INSTALLATION...
Contents SQL EXPRESS INSTALLATION... 1 INSTALLING SQL 2012 EXPRESS... 1 SQL EXPRESS CONFIGURATION... 7 BILLQUICK DATABASE... 9 SQL Express Installation The Microsoft SQL Server 2012 Express software is
4-441-095-12 (1) Network Camera
4-441-095-12 (1) Network Camera SNC easy IP setup Guide Software Version 1.0 Before operating the unit, please read this manual thoroughly and retain it for future reference. 2012 Sony Corporation Table
Set Up E-mail Setup with Microsoft Outlook 2007 using POP3
Page 1 of 14 Help Center Set Up E-mail Setup with Microsoft Outlook 2007 using POP3 Learn how to configure Outlook 2007 for use with your 1&1 e-mail account using POP3. Before you begin, you will need
GSM Ready 56K FAX/MODEM PC Card
GSM Ready 56K FAX/MODEM PC Card Quick Installation Guide M73-APO02-110 INTRODUCTIONS The GSM-Ready 56K Fax/Modem PC Card provides you both fax and data connection via GSM cellular networks. With this combo
Windows Dial Up Networking (DUN) for AirLink Modems Application Note - How To
Windows Dial Up Networking (DUN) for AirLink Modems Application Note - How To Dial-up Networking (DUN) allows a computer or other device to use your AirLink modem to connect to the Internet or private
Dialing Into Dartmouth With Windows 95/98
Dialing Into Dartmouth With Windows 95/98 Who needs this document? Any member of the Dartmouth community who wants to gain access to Dartmouth s network resources, such as electronic mail and the Internet,
Install MS SQL Server 2012 Express Edition
Install MS SQL Server 2012 Express Edition Sohodox now works with SQL Server Express Edition. Earlier versions of Sohodox created and used a MS Access based database for storing indexing data and other
Configuring Network Load Balancing with Cerberus FTP Server
Configuring Network Load Balancing with Cerberus FTP Server May 2016 Version 1.0 1 Introduction Purpose This guide will discuss how to install and configure Network Load Balancing on Windows Server 2012
Important Notes for WinConnect Server VS Software Installation:
Important Notes for WinConnect Server VS Software Installation: 1. Only Windows Vista Business, Windows Vista Ultimate, Windows 7 Professional, Windows 7 Ultimate, Windows Server 2008 (32-bit & 64-bit),
1. Hardware Installation
4 Port 10/100M Internet Broadband Router with USB Printer server Quick Installation Guide #4824904AXZZ0 1. Hardware Installation A. System Requirement Before you getting started, make sure that you meet
Introduction. Before you begin. Installing efax from our CD-ROM. Installing efax after downloading from the internet
Introduction Before you begin Before you begin installing efax, please check the following: You have received confirmation that your application for the efax service has been processed. The confirmation
LPR for Windows 95 TCP/IP Printing User s Guide
LPR for Windows 95 TCP/IP Printing User s Guide First Edition Printed in Taiwan, R.O.C. RECYCLABLE Copyright Statement Trademarks Limited Warranty Copyright 1997 D-Link Corporation No part of this publication
Quick Note 32. Using Digi RealPort with a Digi TransPort Router. UK Support September 2012
Quick Note 32 Using Digi RealPort with a Digi TransPort Router UK Support September 2012 1 Contents 1 Introduction... 3 1.1 Outline... 3 1.2 Assumptions... 3 1.3 Version... 3 2 Configuration & scenario...
Hypercom Key Loading and Management (HKLM) RS232 PPP Key Injection PC Setup Guide
Hypercom Key Loading and Management (HKLM) RS232 PPP Key Injection PC Setup Guide Hypercom Corporation 8888 East Raintree Drive Scottsdale, Arizona 85260 USA Corporate Telephone: 480.642.5000 Corporate
QUANTIFY INSTALLATION GUIDE
QUANTIFY INSTALLATION GUIDE Thank you for putting your trust in Avontus! This guide reviews the process of installing Quantify software. For Quantify system requirement information, please refer to the
Converting InfoPlus.21 Data to a Microsoft SQL Server 2000 Database
Technical Bulletin Issue Date August 14, 2003 Converting InfoPlus.21 Data to a Microsoft SQL Server 2000 Database Converting InfoPlus.21 Data to a Microsoft SQL Server 2000 Database...2 Introduction...
Dial Up Config & Connecting Instructions with Graphics
Dial Up Config & Connecting Instructions with Graphics Dial Up Config & Connecting Below are the Basic Manual Configurations Connecting to the Internet for the following operating systems: Windows 2000
VPN clients configuration for Windows 98SE - for Library access
VPN clients configuration for Windows 98SE - for Library access Requirements: 1. These instructions are only applicable for a computer that has Windows 98SE with a current Internet dialup connection. Note
Dialing up with Windows 95
L.A. Bridge Win95 Dialup Page: 1 System Requirements Dialing up with Windows 95 These instructions will work with most Windows 95 compatible computers, using the Microsoft dialer software. Most versions
Chapter 2 Preparing Your Network
Chapter 2 Preparing Your Network This document describes how to prepare your network to connect to the Internet through a router and how to verify the readiness of your broadband Internet service from
64-Bit Compatibility with Micromeritics Applications
Tech Tip 7 64-Bit Compatibility with Micromeritics Applications Micromeritics products are designed to operate in most Microsoft Windows environments. However, more current versions of Microsoft Windows,
Network Printing In Windows 95/98/ME
Network Printing In Windows 95/98/ME If you are using Windows 2000/ XP: To install a printer on your network using D-Link Print Server or DI-series router with built-in print server you do not need to
How To Create An Easybelle History Database On A Microsoft Powerbook 2.5.2 (Windows)
Introduction EASYLABEL 6 has several new features for saving the history of label formats. This history can include information about when label formats were edited and printed. In order to save this history,
Important Notes for WinConnect Server ES Software Installation:
Important Notes for WinConnect Server ES Software Installation: 1. Only Windows 8/8.1 Enterprise, Windows 8/8.1 Professional (32-bit & 64-bit) or Windows Server 2012 (64-bit) or Windows Server 2012 Foundation
XStream Remote Control: Configuring DCOM Connectivity
XStream Remote Control: Configuring DCOM Connectivity APPLICATION BRIEF March 2009 Summary The application running the graphical user interface of LeCroy Windows-based oscilloscopes is a COM Automation
Easy Setup Guide for the Sony Network Camera
-878-191-11 (1) Easy Setup Guide for the Sony Network Camera For setup, a computer running the Microsoft Windows Operating System is required. For monitoring camera images, Microsoft Internet Explorer
Installing Novell Client Software (Windows 95/98)
Installing Novell Client Software (Windows 95/98) Platform: Windows 95/98 Level of Difficulty: Intermediate The following procedure describes how to install the Novell Client software. This software allows
1 Getting Started. Before you can connect to a network
1 Getting Started This chapter contains the information you need to install either the Apple Remote Access Client or Apple Remote Access Personal Server version of Apple Remote Access 3.0. Use Apple Remote
SECURITY SYSTEM MANAGEMENT SOFTWARE FOR WINDOWS. Quick Start Instructions
TM SECURITY SYSTEM MANAGEMENT SOFTWARE FOR WINDOWS Quick Start Instructions Introduction WinLoad for Windows was developed to simplify and speed up the task of programming Paradox control panels. Remote
1. CONFIGURING REMOTE ACCESS TO SQL SERVER EXPRESS
1. CONFIGURING REMOTE ACCESS TO SQL SERVER EXPRESS From the Start menu, point to All Programs, point to Microsoft SQL Server 2005, point to Configuration Tools, and then click SQL Server Configuration
GRICdial User's Guide
GRICdial User's Guide Table of Contents System Requirements Getting Connected Additional Settings Main Menu Functions Setting up Proxy FAQ System Requirements For Windows 95 You should have the following
Tufts VPN Client User Guide for Windows
Tufts VPN Client User Guide for Windows Introduction The Tufts Virtual Private Network (VPN) implementation is a service that is provided to the faculty and staff of Tufts University to enable secure access
Iridium Extreme TM Satellite Phone. Data Services Manual
Iridium Extreme TM Satellite Phone Data Services Manual Table of Contents 1 OVERVIEW... 1 2 HOW IT WORKS... 1 3 BEFORE INSTALLING... 2 4 USB DRIVER INSTALLATION... 3 5 MODEM INSTALLATION AND CONFIGURATION...
SAPIP GUI INSTALLATION. Table of Contents
QUICK START GUIDE SAPIP GUI INSTALLATION Table of Contents 1. Install CSU cable driver for SapIP..2-3 2. Check for pre-requisite for SAPIP GUI install......2 3. Check for pre-requisite for SAPIP GUI install...2-6
Guide to Setting up Internet Connection Sharing for Windows
Guide to Setting up Internet Connection Sharing for Windows Document Date: December 20, 2005 Document Version: Version: 1.0 Disclaimer: Please note that this document is provided on an as is where is basis
Internet Guide. Prepared for 55 John Street
Internet Guide Prepared for 55 John Street I. Internet Service How do I connect to the Internet? WiFi (Wireless Connectivity) is available throughout the building. In order to connect, you will need a
HYPERLINK Internet PC setup guide. HYPERLINK Internet support helpdesk at 1-866-302-5525.
HYPERLINK Internet support helpdesk at 1-866-302-5525. Congratulations on your new residence and welcome to HYPERLINK Internet service. In a few short moments you will be connected to one of the fastest
Setting Up Windows 95/98 for Dial-In
Page: 1 Setting Up Windows 95/98 for Dial-In First make sure Windows 95/98 is installed on your PC and your modem is configured for use by Windows 95/98. Step 1: Setup the connection Open up My Computer
Experiment # 6 Remote Access Services
Experiment # 6 Remote Access Services 7-1 : Introduction Businesses today want access to their information anywhere, at any time. Whether on the road with customers or working from home, employees need
Upgrading from Call Center Reporting to Reporting for Call Center
Upgrading from Call Center Reporting to Reporting for Call Center www.nortelnetworks.com 2003 Nortel Networks i Table of Contents Table of Contents Change History...1 How to use this guide...2 Introduction...
Windows 95 Revision B Installation Instructions
Windows 95 Revision B Installation Instructions Follow the instructions in this document if you are installing Live200 1.5 on a PC that runs Windows 95 revision B (OSR2). The Windows 95 version number
Quick Reference Guide: Business Mail
: Business Mail TABLE OF CONTENTS GENERAL INFORMATION...2 DETAILED STEPS ON CONFIGURING WINDOWS FOR E-MAIL...2 Set-up For Microsoft Outlook Express...7 Set-up Of Microsoft Outlook On Windows XP...9 PROBLEMS
Prestige 650R-31/33 Read Me First
Prestige 650R-31/33 Read Me First Prestige Rear Panel Connections PORT DSL CONSOLE LAN 10/100M POWER Connect to a telephone jack using a telephone wire. CONNECTION Connect to a serial port (COM port) on
Aquadyne TechTip TITLE: TROUBLESHOOTING PC COM PORT AND MODEM PRODUCTS AFFECTED SYMPTOMS POSSIBLE CAUSES
Aquadyne TechTip TITLE: TROUBLESHOOTING PC COM PORT AND MODEM COMMUNICATIONS WITH AN OCTOPUS. Article # 072297-1 Last reviewed: 03/25/98 Keywords: Serial Port, Modem, Polling, AquaWeb, Node Not Responding
If you are unable to set up your Linksys Router by using one of the above options, use the steps below to manually configure your router.
This article describes how to manually configure a Linksys Router for broadband DSL that uses PPPoE (Point-to-Point Protocol over Ethernet) for authentication. For automatic configuration options, please
AXIS 1440 Print Server For EPSON Printers: Product Update. Important Information for Windows
Important Information for Windows AXIS 1440 Print Server For EPSON Printers: Product Update Important Information for Windows If you are using Windows 95, Windows 98, or Windows NT 4.0, you need to turn
DIRECT INTERNET 3. Install Guide for the Mac OS Operating System
DIRECT INTERNET 3 Install Guide for the Mac OS Operating System Iridium Communications Inc. Rev. 1; October 15, 2010 Overview Iridium s Direct Internet Data Service allows customers to connect directly
Configuring the OfficeConnect Secure Gateway for a remote L2TP over IPSec connection
Creating L2TP over IPSec VPNs between the OfficeConnect Cable/DSL Secure Gateway and the Microsoft VPN Client 1.0 Introduction The OfficeConnect Cable/DSL Secure Gateway supports IPSec, PPTP and L2TP over
Attachment E ACCESSING THE FCC NETWORK USING WINDOWS 95/98 FOR ULS FILING
Attachment E ACCESSING THE FCC NETWORK USING WINDOWS 95/98 FOR ULS FILING This attachment describes how to use Windows 95/98 Dial-Up Networking to establish a direct connection from your PC to the FCC
Network FAX Driver. Operation Guide
Network FAX Driver Operation Guide About this Operation Guide This Operation Guide explains the settings for the Network FAX driver as well as the procedures that are required in order to use the Network
How to configure the DBxtra Report Web Service on IIS (Internet Information Server)
How to configure the DBxtra Report Web Service on IIS (Internet Information Server) Table of Contents Install the DBxtra Report Web Service automatically... 2 Access the Report Web Service... 4 Verify
Installing the KX-P8420 or KX-PS8100 on Windows NT 4.0.
Installing the KX-P8420 or KX-PS8100 on Windows NT 4.0. Overview The KX-P8420 and KX-PS8100 can be set up using 2 methods. METHOD 1 The printer can be installed on the NT server and setup as a shared device.
Client for Macintosh
Client for Macintosh Installation Instructions Sequencher Server Network Overview Page 2 Installing the KeyAccess Client Page 3 Logging on to the Server on OSX Page 4 Logging on to the Server in Classic
Installing Cobra 4.7
Installing Cobra 4.7 Stand-alone application using SQL Server Express A step by step guide to installing the world s foremost earned value management software on a single PC or laptop. 1 Installing Cobra
Configuring the WT-4 for ftp (Ad-hoc Mode)
En Configuring the WT-4 for ftp (Ad-hoc Mode) Windows XP Introduction This document provides basic instructions on configuring the WT-4 wireless transmitter and a Windows XP Professional SP2 ftp server
DSL-G604T Wireless ADSL Router
This product can be set up using any current web browser, i.e., Internet Explorer 6 or Netscape Navigator 6.2.3. DSL-G604T Wireless ADSL Router Before You Begin 1. If you purchased this Router to share
CIMHT_006 How to Configure the Database Logger Proficy HMI/SCADA CIMPLICITY
CIMHT_006 How to Configure the Database Logger Proficy HMI/SCADA CIMPLICITY Outline The Proficy HMI/SCADA CIMPLICITY product has the ability to log point data to a Microsoft SQL Database. This data can
Quick Installation Guide Network Management Card
Rev.1.1 www.cyberpowersystems.com Quick Installation Guide Network Management Card Intelligent Network Management Card allows UPS to be managed, monitored, and configured via SNMP Card Configuration Tool
If the printer is connected to a computer by a USB cable, and you are using the printer sharing function
This document describes how to setup the printer when you are using an operating system equipped with Windows Firewall such as Windows XP Service Pack 2. Make sure that you read the
Maintaining the Content Server
CHAPTER 7 This chapter includes the following Content Server maintenance procedures: Backing Up the Content Server, page 7-1 Restoring Files, page 7-3 Upgrading the Content Server, page 7-5 Shutting Down
DIRECT INTERNET DATA. User s Guide
DIRECT INTERNET DATA User s Guide Iridium Satellite LLC Rev. 2; June 15, 2001 DIRECT INTERNET DATA ------------------------------------------------------------------------------------- TABLE OF CONTENTS
Setting Up Your FTP Server
Requirements:! A computer dedicated to FTP server only! Linksys router! TCP/IP internet connection Steps: Getting Started Configure Static IP on the FTP Server Computer: Setting Up Your FTP Server 1. This
If you need additional assistance please contact our Technical Support Center at 24 hours a day, 7 days a week.
Cisco SPA 2100 Phone Adapter Installation Manual Index Installation of the Cisco SPA 2100 Phone Adapter to NationPhone P. 1 Index, before you begin, and what is included P.2 Installing the NationPhone
Lee County School Configuring Spec Ed Laptop Computers for Dialup, DSL/Cable Modem, and Wireless Access To the Internet
Lee County School Configuring Spec Ed Laptop Computers for Dialup, DSL/Cable Modem, and Wireless Access To the Internet Prepared by: Rich Morgan Technology Director Configuring your Spec Ed laptop for
BioWin Network Installation
BioWin Network Installation Introduction This document outlines the procedures for installing the network version of BioWin. There are three parts to the network version installation: 1. The installation
STATISTICA VERSION 9 STATISTICA ENTERPRISE INSTALLATION INSTRUCTIONS FOR USE WITH TERMINAL SERVER
Notes: STATISTICA VERSION 9 STATISTICA ENTERPRISE INSTALLATION INSTRUCTIONS FOR USE WITH TERMINAL SERVER 1. These instructions focus on installation on Windows Terminal Server (WTS), but are applicable
Reference and Troubleshooting: FTP, IIS, and Firewall Information
APPENDIXC Reference and Troubleshooting: FTP, IIS, and Firewall Information Although Cisco VXC Manager automatically installs and configures everything you need for use with respect to FTP, IIS, and the
Print Audit 6 - SQL Server 2005 Express Edition
Print Audit 6 - SQL Server 2005 Express Edition Summary This is a step-by-step guide to install SQL Server 2005 Express Edition to use as a database for Print Audit 6. Pre-Requisites There are a few pre-requisites
Outlook Profile Setup Guide Exchange 2010 Quick Start and Detailed Instructions
HOSTING Administrator Control Panel / Quick Reference Guide Page 1 of 9 Outlook Profile Setup Guide Exchange 2010 Quick Start and Detailed Instructions Exchange 2010 Outlook Profile Setup Page 2 of 9 Exchange
Installation Instruction STATISTICA Enterprise Small Business
Installation Instruction STATISTICA Enterprise Small Business Notes: ❶ The installation of STATISTICA Enterprise Small Business entails two parts: a) a server installation, and b) workstation installations
NovaBACKUP xsp Version 15.0 Upgrade Guide
NovaBACKUP xsp Version 15.0 Upgrade Guide NovaStor / November 2013 2013 NovaStor, all rights reserved. All trademarks are the property of their respective owners. Features and specifications are subject
This document details the following four steps in setting up a Web Server (aka Internet Information Services -IIS) on Windows XP:
Wazza s QuickStart: Setting up a Web Server (IIS) Windows XP This document details the following four steps in setting up a Web Server (aka Internet Information Services -IIS) on Windows XP: Configuring
Remote Annex. Quick Start for Windows. Read before installing and using Remote Annex Software Release 4.2
Remote Annex Quick Start for Windows Read before installing and using Remote Annex Software Release 4.2 These installation notes contain information specific to this release. This information is not available
How to create a dialup connection to an S8X00 Media Server
How to create a dialup connection to an S8X00 Media Server Useful when customers wants to dial into their S8X00 server, however unlikely that situation is. Typically, customers will be able to access their
Scan to E-mail Quick Setup Guide
Xerox WorkCentre M118i Scan to E-mail Quick Setup Guide 701P42574 This guide provides a quick reference for setting up the Scan to E-mail feature on the Xerox WorkCentre M118i. It includes procedures for:
Remote Access for Cisco Unity 8.x
CHAPTER 9 Remote Access for Cisco Unity 8.x Accessing Cisco Unity 8.x Remotely There are several methods that allow remote access to the Cisco Unity server so that you can do tasks such as loading updates
DIGITAL FULL COLOR MULTIFUNCTIONAL SYSTEM. Software Setup Guide
DIGITAL FULL COLOR MULTIFUNCTIONAL SYSTEM Software Setup Guide BEFORE INSTALLING THE SOFTWARE SETUP IN A WINDOWS ENVIRONMENT SETUP IN A MACINTOSH ENVIRONMENT TROUBLESHOOTING Thank you for purchasing this
Deploying Windows Streaming Media Servers NLB Cluster and metasan
Deploying Windows Streaming Media Servers NLB Cluster and metasan Introduction...................................................... 2 Objectives.......................................................