Technical Reference OPEN824RL / RLW ADSL / VoIP Routers

Transcription

1 OPEN824RL / RLW VoIP/(802.11g) ADSL2+ Router Technical Reference

2 Copyright Copyright 2006 OPEN Networks Pty Ltd. All rights reserved. The content of this manual is subject to change without notice. The information and messages contained herein are proprietary to OPEN Networks Pty Ltd. No part of this manual may be translated, transcribed, reproduced, in any form, or by any means without prior written permission by OPEN Networks Pty Ltd. Disclaimer For content and procedures available in this document, OPEN Networks Pty Ltd does not warrant or assume any legal liability or responsibility for the accuracy, completeness, or usefulness of any information, apparatus, product, or process disclosed. Revision: v2 Date Released: 29 May 2006

3 Technical Reference Table of Contents Introduction...5 Introduction to your Router...5 Features...5 Installing the Router...7 Important note for using this router...7 Package Contents...7 The Front LEDs...8 The Rear Ports...9 Cabling...10 Basic Installation...11 Connecting your router...11 Configuring Computers in Windows XP...13 Configuring Computers in Windows Configuring Computers In Windows 95/98/ME...17 Configuring Computers in Windows NT Factory Default Settings...20 Web Interface (Username and Password)...20 LAN Device IP Settings...20 ISP setting in WAN site...20 DHCP server...20 LAN and WAN Port Addresses...20 Information from your ISP...21 Configuring with your Web Browser...22 Configuration...23 Status...23 ARP Table...23 Wireless Association Table (Wireless Router only)...24 Routing Table...24 DHCP Table...25 Leased Table...25 Expired Table...25 Permanent Table Status...26 VoIP Status...27 Event Log...27 Error Log...28 NAT Sessions...28 Diagnostics...29 UPnP Portmap...29 Quick Start...30 Configuration...32 LAN (Local Area Network)...32 Bridge Interface...32 Ethernet...33 IP Alias...34 Ethernet Client Filter...35 Wireless (Wireless Router only)...36 ii

4 Technical Reference Wireless Security (Wireless Router only)...38 Wireless Client (MAC Address) Filter (Wireless Router only)...40 Port Setting...41 DHCP Server...42 WAN (Wide Area Network)...44 ISP...44 DNS...52 ADSL...53 System...54 Time Zone...54 Remote Access...55 Firmware Upgrade...55 Backup / Restore...56 Restart Router...56 User Management...57 Firewall and Access Control...58 General Settings...59 Packet Filter...60 Packet Filter Add TCP/UDP Filter...62 Packet Filter Add Raw IP Filter...63 Configuring Packet Filters:...65 Intrusion Detection...67 URL Filter...70 Firewall Log...72 VoIP (Voice over Internet Protocol)...73 Wizard...73 General Settings...74 How To Register To The SIP Server...75 Phone Ports...76 PSTN Dial Plan...78 VoIP Dial Plan...81 Adding VoIP Dial Plan Rules...82 Ring & Tone Configuration...83 Special Dial Codes...84 QoS (Quality of Service)...85 Prioritization...85 Outbound IP Throttling (LAN to WAN)...87 Inbound IP Throttling (WAN to LAN)...88 Virtual Server ( Port Forwarding )...91 Adding A Virtual Server...92 Editing A DMZ Host...94 Editing A One-to-One NAT (Network Address Translation)...95 Time Schedule...98 Configuration of Time Schedule...99 Advanced Static Route Dynamic DNS Check Device Management IGMP VLAN Bridge iii

5 Technical Reference Advanced VLAN Setup Example (Triple Play) Save Configuration to Flash Logout Troubleshooting Problems starting up the router Problems with the WAN Interface Problems with the LAN Interface iv

6 Technical Reference Introduction Introduction to your Router Welcome to the VoIP/(802.11g) ADSL2+ Router. The router is an all-in-one VoIP ADSL router, combining an ADSL modem, ADSL router, Ethernet network switch and 2 ports for Voice over IP functionalities, providing everything you need to get the machines on your network connected to the Internet over your ADSL broadband connection. With features such as an ADSL Quick-Start wizard and DHCP Server, you can be online in no time at all and with a minimum of fuss and configuration, catering for first-time users to the guru requiring advanced features and control over their Internet connection and network. Features Voice over IP compliance with SIP standard The router supports cost-effective, toll-quality voice calls over the Internet. It complies with the most popular industrial standard, SIP protocol, to ensure the interoperability with SIP devices and major VoIP Gateways. The VoIP ADSL router supports call waiting, silence suppression, voice activity detection (VAD), comfort noise generation (CNG), line echo cancellation, caller ID (Bell 202, V3) and so on. Lifeline Support The router integrates RJ-11 FXO port for inbound and outbound calls transmitted through the PSTN. Users can receive phone calls from the PSTN while enjoying VoIP call service at the same time. In addition, the device automatically falls back to lifeline POTS to enable making normal phone calls when there is a power outage, or when the Internet connection is down. Express Internet Access The router complies with ADSL worldwide standards. It supports downstream rate up to 12/24 Mbps with ADSL2/2+, 8Mbps with ADSL. Users enjoy not only high-speed ADSL services but also broadband multimedia applications such as interactive gaming, video streaming and real-time audio more easily and faster than ever. It is compliant with Multi-Mode standard (ANSI T1.413, Issue 2; G.dmt (ITU G.992.1); G.lite (ITU G.992.2); G.hs (ITU G994.1); G.dmt.bis (ITU G.992.3); G.dmt.bisplus (ITU G.992.5)) g Wireless AP with WPA Support With an integrated g Wireless Access Point in the router, the device offers quick and easy access to wired networks, wireless networks and broadband connections (ADSL) with single device simplicity, and as a result, mobility to users. In addition to 54 Mbps g data rate, it also interoperates backwardly with existing b equipment. The Wireless Protected Access (WPA) and Wireless Encryption Protocol (WEP) supported features enhance the security level of data protection and access control via Wireless LAN. Fast Ethernet Switch A 4-port 10/100Mbps fast Ethernet switch is built in with automatic switching between MDI and MDI-X for 10Base-T and 100Base-TX ports. An Ethernet straight or crossover cable can be used directly for auto detection. Multi-Protocol to Establish A Connection Supports PPPoA (RFC PPP over ATM Adaptation Layer 5), RFC 1483 encapsulation over ATM (bridged or routed), PPP over Ethernet (RFC 2516), and IPoA (RFC1577) to establish a connection with the ISP. The product also supports VC-based and LLC-based multiplexing. Quick Installation Wizard Supports a WEB GUI page to install the device quickly. With this wizard, end users can enter the information easily which they get from their ISP, then surf the Internet immediately. Universal Plug and Play (UPnP) and UPnP NAT Traversal This protocol is used to enable simple and robust connectivity among stand-alone devices and PCs from many different vendors. It makes networking simple and affordable for users. UPnP architecture leverages TCP/IP and the Web to enable seamless proximity networking in addition to control and data transfer among networked devices. With this feature enabled, users can now connect to Net meeting or MSN Messenger seamlessly. 5

7 Technical Reference Network Address Translation (NAT) Allows multi-users to access outside resources such as the Internet simultaneously with one IP address/one Internet access account. Many application layer gateway (ALG) are supported such as web browser, ICQ, FTP, Telnet, , News, Net2phone, Ping, NetMeeting, IP phone and others. SOHO Firewall Security with DoS and SPI Along with the built-in NAT natural firewall feature, the router also provides advanced hacker pattern-filtering protection. It can automatically detect and block Denial of Service (DoS) attacks. The router is built with Stateful Packet Inspection (SPI) to determine if a data packet is allowed through the firewall to the private LAN. Domain Name System (DNS) relay Provides an easy way to map the domain name (a friendly name for users such as and IP address. When a local machine sets its DNS server with this router s IP address, every DNS conversion request packet from the PC to this router will be forwarded to the real DNS in the outside network. Dynamic Domain Name System (DDNS) The Dynamic DNS service allows you to alias a dynamic IP address to a static hostname. This dynamic IP address is the WAN IP address. For example, to use the service, you must first apply for an account from a DDNS service like More than 5 DDNS servers are supported. Quality of Service (QoS) QoS gives you full control over which types of outgoing data traffic should be given priority by the router, ensuring important data like gaming packets, customer information, or management information move through the router ay lightning speed, even under heavy load. The QoS features are configurable by source IP address, destination IP address, protocol, and port. You can throttle the speed at which different types of outgoing data pass through the router, to ensure P2P users don t saturate upload bandwidth, or office browsing doesn t bring client web serving to a halt. In addition, or alternatively, you can simply change the priority of different types of upload data and let the router sort out the actual speeds. Virtual Server ( port forwarding ) Users can specify some services to be visible from outside users. The router can detect incoming service requests and forward either a single port or a range of ports to the specific local computer to handle it. For example, a user can assign a PC in the LAN acting as a WEB server inside and expose it to the outside network. Outside users can browse inside web servers directly while it is protected by NAT. A DMZ host setting is also provided to a local computer exposed to the outside network, Internet. Rich Packet Filtering Not only filters the packet based on IP address, but also based on Port numbers. It will filter packets from and to the Internet, and also provides a higher level of security control. Dynamic Host Configuration Protocol (DHCP) client and server In the WAN site, the DHCP client can get an IP address from the Internet Service Provider (ISP) automatically. In the LAN site, the DHCP server can allocate a range of client IP addresses and distribute them including IP address, subnet mask as well as DNS IP address to local computers. It provides an easy way to manage the local IP network. Static and RIP1/2 Routing Supports an easy static routing table or RIP1/2 routing protocol to support routing capability. Simple Network Management Protocol (SNMP) It is an easy way to remotely manage the router via SNMP. Web based GUI Supports web based GUI for configuration and management. It is user-friendly and comes with on-line help. It also supports remote management capability for remote users to configure and manage this product. Firmware Upgradeable Device can be upgraded to the latest firmware through the WEB based GUI. Rich management interfaces Supports flexible management interfaces. Users can use Telnet, WEB GUI, and SNMP through LAN or WAN ports to configure and manage the device. 6

8 Technical Reference Installing the Router Important note for using this router Do not use this router in high humidity or high temperatures. Do not use the same power source for this router as other equipment. WARNING! Do not open or repair the case yourself. If this router is too hot, turn off the power immediately and have it repaired at a qualified service centre. Avoid using this product and all accessories outdoors. Place this router on a stable surface. ATTENTION!! Only use the power adaptor that comes with the package. Using a different voltage rating power adaptor may damage this router. Package Contents VoIP/(802.11g) ADSL2 Router CD-ROM containing the online manual RJ-11 ADSL/telephone Cable Ethernet (CAT-5 LAN) Cable AC-DC power adaptor (12VDC, 1.2A) A detachable antenna (OPEN824RLW only) Quick Start Guide Line Splitter / Filter Console kit 7

9 Technical Reference The Front LEDs LED Meaning 1 PWR Lit when power is ON. 2 SYS Lit when the system is ready. 3-6 LAN Port 1X 4X (RJ-45 connector) Lit when connected to an Ethernet device. Green for 100Mbps; Orange for 10Mbps. Blinking when data is Transmitted / Received. 7 WLAN (Wireless Router only) Lit green when the wireless connection is established. Flashes when sending/receiving data. 8 9 Phone 1X 2X (RJ-11 connector) Lit green when the phone is off-hook. 10 LINE (Wireless Router only) Lit when the inbound and outbound calls are transmitted through PSTN. 11 VoIP 1 -VoIP 2 Lit when SIP registration is OK. 12 ADSL/PPP Lit when successfully connected to an ADSL DSLAM ( linesync ). 8

10 Technical Reference The Rear Ports OPEN 824RLW VoIP/802.11g ADSL Router OPEN 824RL VoIP ADSL Router Port Meaning 1 Power Switch Power ON/OFF switch 2 PWR Connect the supplied power adaptor to this jack. 3 RESET LAN 4 1X 4X After the device is powered on, press it to reset the device or restore to factory default settings. 0-3 seconds: reset the device 6 seconds above: restore to factory default settings (this is used when you can not login to the router, e.g. forgot the password) Connect the Ethernet cable to one of the four LAN ports when connecting to a computer or an office/home network of 10Mbps or 100Mbps. 5 Phone 1X 2X Connect the phone cable to this port when connecting to an analog phone set. 9

11 Technical Reference 6 LINE Connect the line cable to this port when connecting to the telephone wall jack. 7 ADSL Antenna 8 (Wireless Router only) Connect the supplied telephone cable to this port when connecting to the ADSL/telephone network. Connect the detachable antenna to this port. Cabling One of the most common causes of problems is bad cabling or ADSL line(s). Make sure that all connected devices are turned on. On the front of the product is a bank of LEDs. Verify that the LAN Link and ADSL line LEDs are lit. If they are not, verify that you are using the proper cables. Ensure that all other devices connected to the same telephone line as your router (e.g. telephones, fax machines, analogue modems) have a line filter connected between them and the wall socket (unless you are using a Central Splitter or Central Filter installed by a qualified and licensed electrician), and ensure that all line filters are correctly installed and the right way around. Missing line filters or line filters installed the wrong way around can cause problems with your ADSL connection, including causing frequent disconnections. 10

12 Basic Installation The router can be configured with your web browser. A web browser is included as a standard application in the following operating systems: Linux, Mac OS, Windows 98/NT/2000/XP/Me, etc. The product provides a very easy and user-friendly interface for configuration. Computers must have an Ethernet interface installed properly and be connected to the router either directly or through an external repeater hub, and have TCP/IP installed and configured to obtain an IP address through a DHCP server or a fixed IP address that must be in the same subnet as the router. The default IP address of the router is and the subnet mask is (i.e. any attached computer must be in the same subnet, and have an IP address in the range of to ). The best and easiest way is to configure the computer to get an IP address automatically from the router using DHCP. If you encounter any problems accessing the router s web interface it may also be advisable to uninstall any kind of software firewall on your computers, as they can cause problems accessing the IP address of the router. Users should make their own decisions on how to best protect their network. Please follow the steps below for your computer s network environment installation. First of all, please check your computer s network components. The TCP/IP protocol stack and Ethernet network adapter must be installed. If not, please refer to your Windows-related or other operating system manuals. NOTE: Any TCP/IP capable workstation can be used to communicate with or through the router. To configure other types of workstations, please consult the manufacturer s documentation. Connecting your router step 1 step 2 step 3 step 4 step 5 Connect this router to a LAN (Local Area Network) and the ADSL/telephone (ADSL) network. Power on the device. Make sure the PWR and SYS LEDs are lit steadily and that the LAN LED is lit. Connect a phone cable to the phone Port when connecting to an analog phone set. Connect a phone cable to the LINE Port when connecting to the telephone wall jack. 11

13 VoIP/802.11g ADSL Router with LINE port ADSL Phone Switching/ HUB ADSL Splitter Line Analog Phone Connect more computers 12

14 Configuring Computers in Windows XP step 1 Click Start / Control Panel (in Classic View). From the Control Panel window, double-click Network Connections. The following appears: step 2 Double-click the Local Area Network connection name required. step 3 Click Properties. The following appears: step 4 Ensure the General tab is active, and highlight Internet Protocol (TCP/IP), then click OK. The following appears: 13

15 step 5 Highlight the Obtain an IP address automatically and the Obtain DNS server address automatically radio buttons, then click OK to complete the configuration. 14

16 Configuring Computers in Windows 2000 step 1 Click Start / Settings / Control Panel. From the Control Panel window, double-click Network and Dial-up Connections. The following appears: step 2 Double-click the Local Area Connection name as required. The following appears: step 3 From the Local Area Connection Status window, click Properties. The following appears: step 4 Highlight Internet Protocol (TCP/IP) and click Properties. The following appears: 15

17 step 5 Highlight the Obtain an IP address automatically and the Obtain DNS server address automatically radio buttons, then click OK to complete the configuration. 16

18 Configuring Computers In Windows 95/98/ME step 1 Click Start / Settings / Control Panel. From the Control Panel window, double-click Network and highlight the Configuration tab to make it active. The following appears: step 2 Highlight TCP / IP -> NE2000 Compatible, or the name of any Network Interface Card (NIC) in your PC, then click Properties. The following appears: step 3 step 4 Highlight the IP Address tab to make it active, then highlight the Obtain an IP address automatically radio button. Highlight the DNS Configuration tab to make it active. The following appears: 17

19 step 5 Highlight the Disable DNS radio button, then click OK to complete the configuration. 18

20 Configuring Computers in Windows NT4.0 step 1 Click Start / Settings / Control Panel. From the Control Panel window, double-click Network and highlight the Protocols tab to make it active. The following appears: step 2 Highlight TCP/IP Protocol, then click Properties. The following appears: step 3 Highlight the Obtain an IP address from a DHCP server radio button, then click OK to complete the configuration. 19

21 Factory Default Settings Before configuring your, you need to know the following default settings. Web Interface (Username and Password) Username: admin Password: admin The default username and password are admin and admin respectively. NOTE: If you ever forget your login password, you may press the RESET button for up to 6 seconds to restore factory default settings. LAN Device IP Settings IP Address: Subnet Mask: ISP setting in WAN site PPPoE DHCP server DHCP server is enabled. Start IP Address: End IP Address: IP pool counts: 100 LAN and WAN Port Addresses The parameters of LAN and WAN ports are pre-set in the factory. The default values are shown below. LAN Port IP address Subnet Mask DHCP server function IP addresses for distribution to PCs Enabled 100 IP addresses continuing from through WAN Port The PPPoE function is enabled to automatically get the WAN port configuration from the ISP, but you have to set the username and password first. 20

22 Information from your ISP Before configuring this device, you have to check with your ISP (Internet Service Provider) what kind of service is provided such as PPPoE, PPPoA, RFC1483, or IPoA. Gather the information as illustrated in the following table and keep it for reference. PPPoE PPPoA RFC1483 Bridged RFC1483 Routed VPI/VCI, VC-based/LLC-based multiplexing, Username, Password, Service Name, and Domain Name System (DNS) IP address (it can be automatically assigned by your ISP when you connect or be set manually). VPI/VCI, VC-based/LLC-based multiplexing, Username, Password, and Domain Name System (DNS) IP address (it can be automatically assigned by your ISP when you connect or be set manually). VPI/VCI, VC-based/LLC-based multiplexing to use Bridged Mode. VPI/VCI, VC-based/LLC-based multiplexing, IP address, Subnet mask, Gateway address, and Domain Name System (DNS) IP address (it is fixed IP address). IPoA VPI/VCI, VC-based/LLC-based multiplexing, IP address, Subnet mask, Gateway address, and Domain Name System (DNS) IP address (it is fixed IP address). 21

23 Configuring with your Web Browser step 1 Open a web browser, and enter the following address in the Address bar: then click Go. The following appears: step 2 Enter the username and password of admin and admin in the User name: and Password: fields, then click OK. Congratulations! You have now successfully logged onto the OPEN 824RL / RLW! 22

24 Configuration At the configuration homepage, the left navigation pane (where bookmarks are provided) links you directly to the desired setup page, including: Status (ARP Table, Wireless Association Table, Routing Table, DHCP Table, Status, VoIP Status, Event Log, Error Log, NAT Sessions and UPnP Portmap) Quick Start Configuration (LAN, WAN, System, Firewall, VoIP, QoS, Virtual Server, Time Schedule and Advanced) Save Config to FLASH Language (provides user interface in English and French languages) Please see the relevant sections of this manual for detailed instructions on how to configure the VoIP ADSL Router. Status ARP Table This section displays the router s ARP (Address Resolution Protocol) Table, which shows the mapping of Internet (IP) addresses to Ethernet (MAC) addresses. This is useful as a quick way of determining the MAC address of your PC s network interface to use with the router s Firewall MAC Address Filter function. See the Firewall section of this manual for more information on this feature. To Access The ARP Table: From any screen in the web interface, Click Status, then ARP Table. The following appears: Field IP Address MAC Address Interface Static Definition A list of IP addresses of devices on your LAN (Local Area Network). The MAC (Media Access Control) addresses for each device on your LAN. The interface name (on the router) to which this IP Address connects. No For dynamically-generated ARP table entries. Yes For static ARP table entries added by the user. 23

25 Wireless Association Table (Wireless Router only) To Access The Wireless Association screen: From any screen in the web interface, Click Status, then Wireless Association. The following appears: The following table displays the Wireless Association Table fields and their definitions: Field IP Address MAC Definition The IP Address of the wireless client that joins this network. The MAC (Media Access Control) address of the wireless client. Routing Table To Access The Routing Table screen From the menu list, Click Status, then Routing Table. The following appears: Routing Table The following table lists the Routing Table fields and their definitions: Field Valid Destination Netmask Gateway / Interface Cost Definition This indicates a successful routing status. The IP Address of the destination network The destination netmask address The IP address of the gateway or existing interface that this route will use. The number of hops counted as the cost of the route. RIP Routing Table The following table lists the RIP Routing Table fields and their definitions: Field Destination Netmask Gateway Definition The IP Address of the destination network The destination netmask address The IP address of the gateway this route will use. 24

26 Cost The number of hops counted as the cost of the route. DHCP Table The DHCP Table lists the types of leases specified. To Access The DHCP Table screen: From the menu list, Click Status, then DHCP Table. The following appears: The following table lists the Leased table fields and their definitions: Field Leased IP Address Expired Permanent Definition The DHCP-assigned IP Addresses information. A list of IP addresses of devices on your LAN. (Local Area Network.) The expired IP Addresses information. The fixed host mapping information. Leased Table To Access The Leased Table Screen: Once you have accessed the DHCP Table screen, click the Leased link. The following appears: The following table lists the Leased Table fields and their definitions: Field IP Address MAC Address Client Host Name Expiry Definition The IP Address assigned to the client. The client s MAC Address The Host Name (computer name) of the client. The current lease time of client. Expired Table To Access The Expired Table Screen: Once you have accessed the DHCP Table screen, click the Expired link. The following appears Please refer to the Leased Table for field definitions. 25

27 Permanent Table To Access The Permanent Table Screen: Once you have accessed the DHCP Table screen, click the Permanent link. The following appears The following table lists the Permanent Table fields and their definitions: Field Name IP Address MAC Address Maximum Lease Time Definition The name you assigned to the Permanent configuration. The fixed IP address for the specified client. The MAC to be assigned to the fixed IP Address. The Maximum Lease Time interval you allow clients. Status From within the Status screen you can check for s and view details and status for the Account you have configured the router to check. Please see the Advanced section of this manual for details on configuring accounts. To Access The Status Screen: From the menu list, Click Status, then Status. The following appears: 26

28 VoIP Status The VoIP Status screen displays details and status for the VoIP Account you have configured the router to check. Please see the Phone Configuration section of this manual (under VoIP) for details on configuring your VoIP phone. To Access The VoIP Status Screen: From the menu list, Click Status, then VoIP Status. The following appears: Event Log This page displays the router s Event Log entries. Major events are logged to this window, such as when the router s ADSL connection is disconnected, as well as Firewall events when you have enabled Intrusion or Blocking Logging in the Configuration Firewall section of the interface. Please see the Firewall section of this manual for more details on how to enable Firewall logging. To Access The Event Log Screen: From the menu list, Click Status, then Event Log. The following appears: 27

29 Error Log The Error Log details any errors encountered by the router (e.g. invalid names given to entries) are logged to this window. To Access The Error Log: From the menu list, Click Status, then Error Log. The following appears: NAT Sessions This section lists all current NAT sessions between interface of types external (WAN) and internal (LAN). To Access The NAT Sessions Screen: From the menu list, Click Status, then NAT Sessions. The following appears: 28

30 Diagnostics This section allows you to view the connectivity status of the LAN and WAN. It displays the status of the Ethernet and Wireless LAN connections after testing, along with the WAN connection and the results of Ping tests. To Access the Diagnostics Screen: From the menu list, Click Status, then Diagnostics. The following appears: UPnP Portmap Click Refresh to update the details on the screen. The section lists all port-mapping established using UPnP (Universal Plug and Play). Please see the Advanced section of this manual for more details on UPnP and the router s UPnP configuration options. To Access The UPnP Portmap Screen: From the menu list, Click Status, then UPnP Portmap. The following appears: 29

31 Quick Start Clicking the Quick Start link allows you to configure the basic settings required to get your router up and running quickly. Usually, the only details you will need for the Quick Start wizard to get you online are your login (often in the form of your password and the encapsulation type. Your ISP will be able to supply all the details you need. In addition, you have the option to provide specific DNS as you desire, or check the Enable box to get the DNS automatically from your ISP. For detailed instructions on configuring your WAN settings, please see the WAN section of this manual. If you have deleted the current WAN Connection in the WAN ISP section of the interface, you can use the router s PVC Scan feature to attempt to determine the Encapsulation types offered by your ISP. To Access The Auto Scan screen: From any screen in the interface, step 1 step 2 Click Quick Start from the menu list. From the Quick Start screen, click the Auto Scan button. The following appears: step 3 Click Start to begin scanning for the encapsulation types offered by your ISP. If the scan is successful you will then be presented with a list of supported options: 30

32 step 4 Select the desired option from the list and click Apply to return to the Quick Start interface to continue configuring your ISP connection. Please note that the contents of this list will vary, depending on what is supported by your ISP. 31