SAR TEST REPORT. No. I14D00063-SAR. For. Client : ZTE Corporation. Production : LTE/WCDMA/GSM Multi-Mode. Digital Mobile Phone

Size: px
Start display at page:

Download "SAR TEST REPORT. No. I14D00063-SAR. For. Client : ZTE Corporation. Production : LTE/WCDMA/GSM Multi-Mode. Digital Mobile Phone"

Transcription

1 SAR TEST REPORT No. I14D00063-SAR For Client : ZTE Corporation Production : LTE/WCDMA/GSM Multi-Mode Digital Mobile Phone Model Name : ZTE Blade A430 Hardware Version: WMBQ Software Version: ZTE-CN-QB18S-P632A10V0.0.1B01L1 Issued date: Note: The test results in this test report relate only to the devices specified in this report. This report shall not be reproduced except in full without the written approval of ECIT Shanghai. Test Laboratory: ECIT Shanghai, East China Institute of Telecommunications Add: 7-8F, G Area, No.668, Beijing East Road, Huangpu District, Shanghai, P. R. China Tel: (+86) ,

2 Revision Version Report Number Revision Date Memo I14D00063-SAR Initial creation of test report East China Institute of Telecommunications Page Number : 2 of 299

3 CONTENTS 1. TEST LABORATORY TESTING LOCATION TESTING ENVIRONMENT PROJECT DATA SIGNATURE STATEMENT OF COMPLIANCE CLIENT INFORMATION APPLICANT INFORMATION MANUFACTURER INFORMATION EQUIPMENT UNDER TEST (EUT) AND ANCILLARY EQUIPMENT (AE) ABOUT EUT INTERNAL IDENTIFICATION OF EUT USED DURING THE TEST INTERNAL IDENTIFICATION OF AE USED DURING THE TEST TEST METHODOLOGY APPLICABLE LIMIT REGULATIONS APPLICABLE MEASUREMENT STANDARDS SPECIFIC ABSORPTION RATE (SAR) INTRODUCTION SAR DEFINITION SAR MEASUREMENT SETUP MEASUREMENT SET-UP DASY5 E-FIELD PROBE SYSTEM E-FIELD PROBE CALIBRATION OTHER TEST EQUIPMENT DATA ACQUISITION ELECTRONICS(DAE) East China Institute of Telecommunications Page Number : 3 of 299

4 ROBOT MEASUREMENT SERVER DEVICE HOLDER FOR PHANTOM PHANTOM POSITION OF THE WIRELESS DEVICE IN RELATION TO THE PHANTOM GENERAL CONSIDERATIONS BODY-WORN DEVICE DESKTOP DEVICE DUT SETUP PHOTOS TISSUE SIMULATING LIQUIDS EQUIVALENT TISSUES DIELECTRIC PERFORMANCE SYSTEM VALIDATION SYSTEM VALIDATION SYSTEM SETUP MEASUREMENT PROCEDURES TESTS TO BE PERFORMED MEASUREMENT PROCEDURE WCDMA MEASUREMENT PROCEDURES FOR SAR SAR MEASUREMENT FOR LTE POWER DRIFT CONDUCTED OUTPUT POWER GSM MEASUREMENT RESULT WCDMA MEASUREMENT RESULT LTE MEASUREMENT RESULT BT AND WI-FI MEASUREMENT RESULT SAR TEST RESULT East China Institute of Telecommunications Page Number : 4 of 299

5 14. MEASUREMENT UNCERTAINTY MAIN TEST INSTRUMENTS ANNEX A. GRAPH RESULTS ANNEX B. SYSTEM VALIDATION RESULTS ANNEX C. CALIBRATION CERTIFICAT East China Institute of Telecommunications Page Number : 5 of 299

6 1. Test Laboratory 1.1. Testing Location Company Name: Address: ECIT Shanghai, East China Institute of Telecommunications 7-8F, G Area,No. 668, Beijing East Road, Huangpu District, Shanghai, P. R. China Postal Code: Telephone: (+86) Fax: (+86) Testing Environment Normal Temperature: Relative Humidity: 20-75% Ambient noise & Reflection: < W/kg 1.3. Project Data Project Leader: Wang Yaqiong Testing Start Date: Testing End Date: Signature Hu Jiajing (Prepared this test report) Yu Naiping (Reviewed this test report) Zheng Zhongbin Director of the laboratory (Approved this test report) East China Institute of Telecommunications Page Number : 6 of 299

7 2. Statement of Compliance The maximum results of Specific Absorption Rate (SAR) found during testing for ZTE Blade A430 are as follows ( with expanded uncertainty 22.4%) Table 2.1: Max. SAR Measured(10g) Band Position SAR 10g (W/Kg) GSM 900 Head Body DCS 1800 Head Body WCDMA Band I Head Body WCDMA Band VIII Head Body LTE Band 3 Head Body LTE Band 7 Head Body LTE Band 8 Head Body LTE Band 20 Head Body Table 2.2: The maximum of SAR values Maximum SAR value for Head Maximum SAR value for Body GSM WCDMA LTE The SAR values found for the Mobile Phone are below the maximum recommended levels of 2.0 W/Kg as averaged over any 10g tissue according to the EN 50360:2001/AC:2012. The measurement together with the test system set-up is described in chapter 7 of this test report. A detailed description of the equipment under test can be found in chapter 3 of this test report. The maximum SAR value is obtained at the case of (Table 2.2), and the values are: W/Kg (10g). East China Institute of Telecommunications Page Number : 7 of 299

8 3. Client Information 3.1. Applicant Information Company Name: ZTE Corporation Address: ZTE Plaza, Keji Road South, Hi-Tech, industrial Park, Nanshan District, Shenzhen, Guangdong, , P.R.China Telephone: Postcode: Manufacturer Information Company Name: ZTE Corporation Address: ZTE Plaza, Keji Road South, Hi-Tech, industrial Park, Nanshan District, Shenzhen, Guangdong, , P.R.China Telephone: Postcode: East China Institute of Telecommunications Page Number : 8 of 299

9 4. Equipment Under Test (EUT) and Ancillary Equipment (AE) 4.1. About EUT Description: LTE/WCDMA/GSM Multi-Mode Digital Mobile Phone Model name: ZTE Blade A430 Operation Model(s): GSM900/1800,WCDMA2100/900,LTE Band3/7/8/20,Wi-Fi2450 Tx Frequency: MHz, MHz, GSM) , MHz (WCDMA) 1710 MHz 1785 MHz (LTE Band 3) 2500 MHz 2570 MHz (LTE Band 7) 880 MHz 915 MHz (LTE Band 8) 832 MHz 862 MHz (LTE Band 20) 2412 ~ 2472 MHz (Wi-Fi) 2402~2480 MHz (BT) GPRS Multislot Class: 12 Operation mode: B EGPRS Multislot Class: 12 Test device Production information: Production unit Device type: Portable device Antenna type: Inner antenna Accessories/Body-worn Headset configurations: Hotspot mode: Support simultaneous transmission of hotspot and voice ( or data) Dimensions: 13.5cm 7.0cm Picture 4-1: Constituents of the sample East China Institute of Telecommunications Page Number : 9 of 299

10 4.2. Internal Identification of EUT used during the test EUT ID* SN or IMEI HW Version SW Version: N15 IMEI: WMBQ *EUT ID: is used to identify the test sample in the lab internally Internal Identification of AE used during the test ZTE-CN-QB18S-P632A10V 0.0.1B01L1 AE ID* Description Model SN Manufacturer B09 Battery Li3822T43P3h N/A ZTE Corporation A01 Headset N/A N/A ZTE Corporation *AE ID: is used to identify the test sample in the lab internally. East China Institute of Telecommunications Page Number : 10 of 299

11 5. TEST METHODOLOGY 5.1. Applicable Limit Regulations EN 50360:2001+A1:2012: Product standard for the measurement of Specific Absorption Rate related to human exposure to electromagnetic fields from mobile phones. It specifies the maximum exposure limit of 2.0 W/kg as averaged over any 10 gram of tissue for portable devices being used within 20 cm of the user in the uncontrolled environment Applicable Measurement Standards EN : Human exposure to radio frequency fields from hand-held and body-mounted wireless communication devices Human models, instrumentation, and procedures Part 1: Procedure to determine the specific absorption rate (SAR) for hand-held devices used in close proximity to the ear (frequency range of 300 MHz to 3 GHz). IEC : Human exposure to radio frequency fields from hand-held and body-mounted wireless communication devices Human models, instrumentation, and procedures Part 1:Procedure to determine the Specific Absorption Rate (SAR) for hand-held devices used in close proximity to the ear (frequency range of 300 MHz to 3 GHz) IEC : Human exposure to radio frequency fields from hand-held and body-mounted wireless communication devices - Human models, instrumentation, and procedures - Part 2: Procedure to determine the specific absorption rate (SAR) for wireless communication devices used in close proximity to the human body (frequency range of 30 MHz to 6 GHz) EN : Human exposure to radio frequency fields from hand-held and body-mounted wireless communication devices Human models, instrumentation, and procedures Part 2: Procedure to determine the specific absorption rate (SAR) for wireless communication devices used in close proximity to the human body (frequency range of 30 MHz to 6 GHz) EN : Product standard to demonstrate compliance of radio frequency fields from handheld and body-mounted wireless communication devices used by the general public (30 MHz 6 GHz) EN 62479:2010: Assessment of the compliance of low power electronic and electrical equipment with the basic restrictions related to human exposure to electromagnetic fields (10 MHz to 300 GHz) East China Institute of Telecommunications Page Number : 11 of 299

12 6. Specific Absorption Rate (SAR) 6.1. Introduction SAR is related to the rate at which energy is absorbed per unit mass in an object exposed to a radio field. The SAR distribution in a biological body is complicated and is usually carried out by experimental techniques or numerical modeling. The standard recommends limits for two tiers of groups, occupational/controlled and general population/uncontrolled, based on a person s awareness and ability to exercise control over his or her exposure. In general, occupational/controlled exposure limits are higher than the limits for general population/uncontrolled SAR Definition The SAR definition is the time derivative (rate) of the incremental energy ( dw ) absorbed by (dissipated in) an incremental mass ( dm ) contained in a volume element ( dv ) of a given density ( ). The equation description is as below: d dw d dw SAR ( ) ( ) dt dm dt dv SAR is expressed in units of Watts per kilogram (W/kg) SAR measurement can be either related to the temperature elevation in tissue by T SAR c( ) t Where: C is the specific head capacity, T is the temperature rise and t is the exposure duration, or related to the electrical field in the tissue by E SAR 2 Where: is the conductivity of the tissue, is the mass density of tissue and E is the RMS electrical field strength. However for evaluating SAR of low power transmitter, electrical field measurement is typically applied. East China Institute of Telecommunications Page Number : 12 of 299

13 7. SAR MEASUREMENT SETUP 7.1. Measurement Set-up The DASY5 system for performing compliance tests is illustrated above graphically. This system consists of the following items: Picture 7-1 SAR Lab Test Measurement Set-up A standard high precision 6-axis robot (Stäubli TX=RX family) with controller, teach pendant and software. An arm extension for accommodating the data acquisition electronics (DAE). An isotropic field probe optimized and calibrated for the targeted measurement. A data acquisition electronics (DAE) which performs the signal amplification, signal multiplexing, AD-conversion, offset measurements, mechanical surface detection, collision detection, etc. The unit is battery powered with standard or rechargeable batteries. The signal is optically transmitted to the EOC. The Electro-optical converter (EOC) performs the conversion from optical to electrical signals for the digital communication to the DAE. To use optical surface detection, a special version of the EOC is required. The EOC signal is transmitted to the measurement server. The function of the measurement server is to perform the time critical tasks such as signal filtering, control of the robot operation and fast movement interrupts. The Light Beam used is for probe alignment. This improves the (absolute) accuracy of the probe positioning. A computer running WinXP and the DASY5 software. Remote control and teach pendant as well as additional circuitry for robot safety such as warning lamps, etc. The phantom, the device holder and other accessories according to the targeted measurement. East China Institute of Telecommunications Page Number : 13 of 299

14 7.2. DASY5 E-field Probe System The SAR measurements were conducted with the dosimetric probe designed in the classical triangular configuration and optimized for dosimetric evaluation. The probe is constructed using the thick film technique; with printed resistive lines on ceramic substrates. The probe is equipped with an optical multifiber line ending at the front of the probe tip. It is connected to the EOC box on the robot arm and provides an automatic detection of the phantom surface. Half of the fibers are connected to a pulsed infrared transmitter, the other half to a synchronized receiver. As the probe approaches the surface, the reflection from the surface produces a coupling from the transmitting to the receiving fibers. This reflection increases first during the approach, reaches maximum and then decreases. If the probe is flatly touching the surface, the coupling is zero. The distance of the coupling maximum to the surface is independent of the surface reflectivity and largely independent of the surface to probe angle. The DASY5 software reads the reflection durning a software approach and looks for the maximum using 2 nd ord curve fitting. The approach is stopped at reaching the maximum. Probe Specifications: Model: ES3DV3 Frequency Range: Calibration: 10MHz 2.6GHz(ES3DV3) In head and body simulating tissue at Frequencies from 835 up to 5800MHz Linearity: ± 0.2 db(30 MHz to 2.6 GHz) for ES3DV3 Picture 7-2 Near-field Probe Dynamic Range: 10 mw/kg 100W/kg Probe Length: 330 mm Probe Tip Length: 20 mm Body Diameter: 12 mm Tip Diameter: 2.5 mm (3.9 mm for ES3DV3) Tip-Center: 1 mm (2.0mm for ES3DV3) Application: SAR Dosimetry Testing Compliance tests of mobile phones Dosimetry in strong gradient fields Picture 7-3 E-field Probe 7.3. E-field Probe Calibration Each E-Probe/Probe Amplifier combination has unique calibration parameters. A TEM cell calibration procedure is conducted to determine the proper amplifier settings to enter in the probe parameters. The amplifier settings are determined for a given frequency by subjecting the probe to a known E-field density (1 mw/cm 2 ) using an RF Signal generator, TEM cell, and RF Power Meter. The free space E-field from amplified probe outputs is determined in a test chamber. This calibration can be performed in a TEM cell if the frequency is below 1 GHz and inn a waveguide or other methodologies above 1 GHz for free space. For the free space calibration, the probe is East China Institute of Telecommunications Page Number : 14 of 299

15 placed in the volumetric center of the cavity and at the proper orientation with the field. The probe is then rotated 360 degrees until the three channels show the maximum reading. The power density readings equates to 1 mw/ cm 2.. E-field temperature correlation calibration is performed in a flat phantom filled with the appropriate simulated brain tissue. The E-field in the medium correlates with the temperature rise in the dielectric medium. For temperature correlation calibration a RF transparent thermistor-based temperature probe is used in conjunction with the E-field probe. T SAR C t Where: t = Exposure time (30 seconds), C = Heat capacity of tissue (brain or muscle), T = Temperature increase due to RF exposure. SAR E 2 Where: σ = Simulated tissue conductivity, ρ = Tissue density (kg/m 3 ) Other Test Equipment Data Acquisition Electronics(DAE) The data acquisition electronics consist of a highly sensitive electrometer-grade preamplifier with auto-zeroing, a channel and gain-switching multiplexer, a fast 16 bit AD-converter and a command decoder with a control logic unit. Transmission to the measurement server is accomplished through an optical downlink for data and status information, as well as an optical uplink for commands and the clock. The mechanical probe mounting device includes two different sensor systems for frontal and sideways probe contacts. They are used for mechanical surface detection and probe collision detection. The input impedance of the DAE is 200 MOhm; the inputs are symmetrical and floating. Common mode rejection is above 80 db. Picture7-4: DAE East China Institute of Telecommunications Page Number : 15 of 299

16 Robot The SPEAG DASY system uses the high precision robots (DASY5: TX90) type from Stäubli SA (France). For the 6-axis controller system, the robot controller version from Stäubli is used. The Stäubli robot series have many features that are important for our application: High precision (repeatability 0.02mm) High reliability (industrial design) Low maintenance costs (virtually maintenance free due to direct drive gears; no belt drives) Jerk-free straight movements (brushless synchron motors; no stepper motors) Low ELF interference (motor control fields shielded via the closed metallic construction shields) Picture7-5: DASY Measurement Server The Measurement server is based on a PC/104 CPU broad with CPU (DASY5: 400 MHz, Intel Celeron), chipdisk (DASY5: 128MB), RAM (DASY5: 128MB). The necessary circuits for communication with the DAE electronic box, as well as the 16 bit AD converter system for optical detection and digital I/O interface are contained on the DASY I/O broad, which is directly connected to the PC/104 bus of the CPU broad. The measurement server performs all real-time data evaluation of field measurements and surface detection, controls robot movements and handles safety operation. The PC operating system cannot interfere with these time critical processes. All connections are supervised by a watchdog, and disconnection of any of the cables to the measurement server will automatically disarm the East China Institute of Telecommunications Page Number : 16 of 299

17 robot and disable all program-controlled robot movements. Furthermore, the measurement server is equipped with an expansion port which is reserved for future applications. Please note that this expansion port does not have a standardized pinout, and therefore only devices provided by SPEAG can be connected. Devices from any other supplier could seriously damage the measurement server. Picture 7-6: Server for DASY Device Holder for Phantom The SAR in the phantom is approximately inversely proportional to the square of the distance between the source and the liquid surface. For a source at 5mm distance, a positioning uncertainty of ±0.5mm would produce a SAR uncertainty of ±20%. Accurate device positioning is therefore crucial for accurate and repeatable measurements. The positions in which the devices must be measured are defined by the standards. The DASY device holder is designed to cope with the different positions given in the standard. It has two scales for device rotation (with respect to the body axis) and device inclination (with respect to the line between the ear reference points). The rotation centers for both scales is the ear reference point (ERP). Thus the device needs no repositioning when changing the angles. The DASY device holder is constructed of low-loss POM material having the following dielectric parameters: relative permittivity =3 and loss tangent =0.02. The amount of dielectric material has been reduced in the closest vicinity of the device, since measurements have suggested that the influence of the clamp on the test results could thus be lowered. <Laptop Extension Kit> The extension is lightweight and made of POM, acrylic glass and foam. It fits easily on the upper part of the Mounting Device in place of the phone positioner. The extension is fully compatible with the Twin-SAM and ELI phantoms. Picture7-7: Device Holder Picture 7-8: Laptop Extension Kit East China Institute of Telecommunications Page Number : 17 of 299

18 Phantom The SAM Twin Phantom V4.0 is constructed of a fiberglass shell integrated in a table. The shape of the shell is based on data from an anatomical study designed to Represent the 90 th percentile of the population. The phantom enables the dissymmetric evaluation of SAR for both left and right handed handset usage, as well as body-worn usage using the flat phantom region. Reference markings on the Phantom allow the complete setup of all predefined phantom positions and measurement grids by manually teaching three points in the robot. The shell phantom has a 2mm shell thickness (except the ear region where shell thickness increases to 6 mm). Shell Thickness: 2 ± 0. 2 mm Filling Volume: Approx. 25 liters Dimensions: 810 x l000 x 500 mm (H x L x W) Available: Special Picture 7-9: SAM Twin Phantom East China Institute of Telecommunications Page Number : 18 of 299

19 8. Position of the wireless device in relation to the phantom 8.1. General considerations This standard specifies two handset test positions against the head phantom the cheek position and the tilt position. wt Width of the handset at the level of the acoustic wb Width of the bottom of the handset A Midpoint of the width w t of the handset at the level of the acoustic output B Midpoint of the width w b of the bottom of the handset Picture 8-1 Typical fixed case handset Picture 8-2 Typical clam-shell case handset Picture 8-3 Cheek position of the wireless device on the left side of SAM East China Institute of Telecommunications Page Number : 19 of 299

20 Picture 8-4 Tilt position of the wireless device on the left side of SAM 8.2. Body-worn device A typical example of a body-worn device is a mobile phone, wireless enabled PDA or other battery operated wireless device with the ability to transmit while mounted on a person s body using a carry accessory approved by the wireless device manufacturer. Picture 8-5 Test positions for body-worn devices 8.3. Desktop device A typical example of a desktop device is a wireless enabled desktop computer placed on a table or desk when used. The DUT shall be positioned at the distance and in the orientation to the phantom that corresponds to the intended use as specified by the manufacturer in the user instructions. For devices that employ an external antenna with variable positions, tests shall be performed for all antenna positions specified. Picture 8-6 shows positions for desktop device SAR tests. If the intended use is not specified, the device shall be tested directly against the flat phantom. East China Institute of Telecommunications Page Number : 20 of 299

21 Picture 8-6 Test positions for desktop devices East China Institute of Telecommunications Page Number : 21 of 299

22 8.4. DUT Setup Photos Picture 8-7: Specific Absorption Rate Test Layout East China Institute of Telecommunications Page Number : 22 of 299

23 Picture 8-8: Left Head Touch Cheek Position Picture 8-9: Left Head Tilt 15 Position East China Institute of Telecommunications Page Number : 23 of 299

24 Picture 8-10: Right Head Touch Cheek Position Picture 8-11: Right Head Tilt 15 Position East China Institute of Telecommunications Page Number : 24 of 299

25 Test positions for body: The Body SAR is tested at the following 5 test positions all with the distance =10mm between the EUT and the phantom bottom : Picture 8-12: Toward Phantom (10mm) Picture 8-13: Toward Ground (10mm) East China Institute of Telecommunications Page Number : 25 of 299

26 Picture 8-14: Toward Left (10mm) Picture 8-15: Toward Right (10mm) East China Institute of Telecommunications Page Number : 26 of 299

27 Picture 8-16: Toward Bottom (10mm) East China Institute of Telecommunications Page Number : 27 of 299

28 9. Tissue Simulating Liquids 9.1. Equivalent Tissues The liquid used for the frequency range of MHz consisted of water, sugar, salt and Cellulose. The liquid has been previously proven to be suited for worst-case. The Table 9.3 and 9.4 shows the detail solution. It s satisfying the latest tissue dielectric parameters requirements proposed by the IEEE 1528 and IEC Table 9.1. Composition of the Head Tissue Equivalent Matter Frequency (MHz) Ingredients (% by weight) Water Sugar / / / Salt Preventol / / / Cellulose / / / Clycol Monobutyl / / Dielectric Parameters Target Value f=850mhz ε=41.5 σ=0.90 f=900mhz ε=41.5 σ=0.97 f=1800mhz ε=40.0 σ=1.40 f=1950 MHz ε=40.0 σ=1.40 f=2550 MHz ε=39.1 σ=1.91 Table 9.2. Targets for tissue simulating liquid Frequency Conductivity Permittivity Liquid Type ± 5% Range (MHz) (σ) (ε) ± 5% Range 850 Head ~ ~ Head ~ ~ Head ~ ~ Head ~ ~ Head ~ ~41.2 East China Institute of Telecommunications Page Number : 28 of 299

29 9.2. Dielectric Performance Table 9.3: Dielectric Performance of Head Tissue Simulating Liquid Measurement Value Liquid Temperature: 22.5 C Type Frequency Permittivity ε Drift (%) Conductivity σ Drift (%) Test Date Head 850 MHz % % Head 900 MHz % % Head 1800 MHz % % Head 1950 MHz % % Head 2550 MHz % % Picture 9-1: Liquid depth in the Flat Phantom (850 MHz) Picture 9-2: Liquid depth in the Flat Phantom (900 MHz) East China Institute of Telecommunications Page Number : 29 of 299

30 Picture 9-3: Liquid depth in the Flat Phantom (1800 MHz) Picture 9-4: Liquid depth in the Flat Phantom (1950 MHz Head) East China Institute of Telecommunications Page Number : 30 of 299

31 Picture 9-5: Liquid depth in the Flat Phantom (2550 MHz Head) East China Institute of Telecommunications Page Number : 31 of 299

32 10. System Validation System Validation Each DASY system is equipped with one or more system validation kits. These units, together with the predefined measurement procedures within the DASY software, enable the user to conduct the system performace check and system validation. System validation kit includes a dipole, tripod holder to fix it underneath the flat phantom and a corresponding distance holder System Setup In the simplified setup for system evaluation, the DUT is replaced by a calibrated dipole and the power source is replaced by a continuous wave that comes from a signal generator. The calibrated dipole must be placed beneath the flat phantom section of the SAM twin phantom with the correct distance holder. The distance holder should touch the phantom surface with a light pressure at the reference marking and be oriented parallel to the long side of the phantom. The equipment setup is shown below: Picture 10-1 System Setup for System Evaluation The output power on dipole port must be calibrated to 24 dbm (250mW) before dipole is connected. East China Institute of Telecommunications Page Number : 32 of 299

33 Picture 10-2 Photo of Dipole Setup Table 10.1: System Validation of Head Verification Results Input power level: 250mW Frequency Target value (W/kg) Measured value (W/kg) Deviation Test 10 g 1 g 10 g 1 g 10 g 1 g date Average Average Average Average Average Average 835 MHz % 2.07% MHz % -2.68% MHz % -5.04% MHz % -0.30% MHz % -4.82% East China Institute of Telecommunications Page Number : 33 of 299

34 11. Measurement Procedures Tests to be performed In order to determine the highest value of the peak spatial-average SAR of a handset, all device positions, configurations and operational modes shall be tested for each frequency band according to steps 1 to 3 below. A flowchart of the test process is shown in Picture 19 Step 1: The tests described in 11.2 shall be performed at the channel that is closest to the centre of the transmit frequency band ( f c ) for: a) all device positions (cheek and tilt, for both left and right sides of the SAM phantom, as described in Chapter 8), b) all configurations for each device position in a), e.g., antenna extended and retracted, and c) all operational modes, e.g., analogue and digital, for each device position in a) and configuration in b) in each frequency band. If more than three frequencies need to be tested according to 11.1 (i.e., N c > 3), then all frequencies, configurations and modes shall be tested for all of the above test conditions. Step 2: For the condition providing highest peak spatial-average SAR determined in Step 1, perform all tests described in 11.2 at all other test frequencies, i.e., lowest and highest frequencies. In addition, for all other conditions (device position, configuration and operational mode) where the peak spatial-average SAR value determined in Step 1 is within 3 db of the applicable SAR limit, it is recommended that all other test frequencies shall be tested as well. Step 3: Examine all data to determine the highest value of the peak spatial-average SAR found in Steps 1 to 2. East China Institute of Telecommunications Page Number : 34 of 299

35 Picture 11-1 Block diagram of the tests to be performed Measurement procedure The following procedure shall be performed for each of the test conditions (see Picture 19) described in 11.1: a) Measure the local SAR at a test point within 8 mm or less in the normal direction from the inner surface of the phantom. b) Measure the two-dimensional SAR distribution within the phantom (area scan procedure). The boundary of the measurement area shall not be closer than 20 mm from the phantom side walls. The distance between the measurement points should enable the detection of the location of local maximum with an accuracy of better than half the linear dimension of the tissue cube after interpolation. A maximum grip spacing of 20 mm for frequencies below 3 GHz and (60/f [GHz]) mm for frequencies of 3GHz and greater is recommended. The maximum distance between the East China Institute of Telecommunications Page Number : 35 of 299

36 geometrical centre of the probe detectors and the inner surface of the phantom shall be 5 mm for frequencies below 3 GHz andδ In(2)/2 mm for frequencies of 3 GHz and greater, whereδ is the plane wave skin depth and In(x) is the natural logarithm. The maximum variation of the sensor-phantom surface shall be ±1 mm for frequencies below 3 GHz and ±0.5 mm for frequencies of 3 GHz and greater. At all measurement points the angle of the probe with respect to the line normal to the surface should be less than 5. If this cannot be achieved for a measurement distance to the phantom inner surface shorter than the probe diameter, additional uncertainty evaluation is needed. c) From the scanned SAR distribution, identify the position of the maximum SAR value, in addition identify the positions of any local maxima with SAR values within 2 db of the maximum value that are not within the zoom-scan volume; additional peaks shall be measured only when the primary peak is within 2 db of the SAR limit. This is consistent with the 2 db threshold already stated; d) Measure the three-dimensional SAR distribution at the local maxima locations identified in step c). The horizontal grid step shall be (24 / f[ghz] ) mm or less but not more than 8 mm. The minimum zoom size of 30 mm by 30 mm and 30 mm for frequencies below 3 GHz. For higher frequencies, the minimum zoom size of 22 mm by 22 mm and 22 mm. The grip step in the vertical direction shall be ( 8-f[GHz] ) mm or less but not more than 5 mm, if uniform spacing is used. If variable spacing is used in the vertical direction, the maximum spacing between the two closest measured points to the phantom shell shall be (12 / f[ghz]) mm or less but not more than 4 mm, and the spacing between father points shall increase by an incremental factor not exceeding 1.5. When variable spacing is used, extrapolation routines shall be tested with the same spacing as used in measurements. The maximum distance between the geometrical centre of the probe detectors and the inner surface of the phantom shall be 5 mm for frequencies below 3 GHz andδ In(2)/2 mm for frequencies of 3 GHz and greater, where δ is the plane wave skin depth and In(x) is the natural logarithm. Separate grids shall be centered on each of the local SAR maxima found in step c). Uncertainties due to field distortion between the media boundary and the dielectric enclosure of the probe should also be minimized, which is achieved is the distance between the phantom surface and physical tip of the probe is larger than probe tip diameter. Other methods may utilize correction procedures for these boundary effects that enable high precision measurements closer than half the probe diameter. For all measurement points, the angle of the probe with respect to the flat phantom surface shall be less than 5. If this cannot be achieved an additional uncertainty evaluation is needed. e) Use post processing( e.g. interpolation and extrapolation ) procedures to determine the local SAR values at the spatial resolution needed for mass averaging WCDMA Measurement Procedures for SAR The following procedures are applicable to WCDMA handsets operating under 3GPP Release99, Release 5 and Release 6. The default test configuration is to measure SAR with an established radio link between the DUT and a communication test set using a 12.2kbps RMC (reference measurement channel) configured in Test Loop Mode 1. SAR is selectively confirmed for other physical channel configurations (DPCCH & DPDCH n ), HSDPA and HSPA (HSUPA/HSDPA) modes according to output power, exposure conditions and device operating capabilities. Both uplink and downlink should be configured with the same RMC or AMR, when required. SAR for Release 5 HSDPA and Release 6 HSPA are measured using the applicable FRC (fixed reference East China Institute of Telecommunications Page Number : 36 of 299

37 channel) and E-DCH reference channel configurations. Maximum output power is verified according to applicable versions of 3GPP TS and SAR must be measured according to these maximum output conditions. When Maximum Power Reduction (MPR) is not implemented according to Cubic Metric (CM) requirements for Release 6 HSPA, the following procedures do not apply. For Release 5 HSDPA Data Devices: Sub-test c d d (SF) / c d hs CM/dB 1 2/15 15/ /15 4/ /15 15/ /15 24/ /15 8/ /8 30/ /15 4/ /4 30/ For Release 6 HSUPA Data Devices Sub- test c d d (SF) / c d hs ec ed ed (SF) ed (codes) CM (db) MPR (db) AG Index E-TFCI 1 11/15 15/ /15 22/15 209/ / /15 15/ /15 12/15 12/15 12/ /15 9/ /9 30/15 30/15 ed1 :47/15 ed 2 :47/ /15 15/ /15 4/15 4/15 56/ /15 15/ /15 24/15 30/15 134/ SAR Measurement for LTE SAR tests for LTE are performed with a base station simulator, Anritsu MT8820c. Closed loop power control was used so the UE transmits with maximum output power during SAR testing. All powers were measured with the MT8820c Power Drift To control the output power stability during the SAR test, DASY5 system calculates the power drift by measuring the E-field at the same location at the beginning and at the end of the measurement for each test position. These drift values can be found in Table 13.1 to Table 13.8 labeled as: (Power Drift [db]). This ensures that the power drift during one measurement is within 5%. East China Institute of Telecommunications Page Number : 37 of 299

38 12. Conducted Output Power GSM Measurement result During the process of testing, the EUT was controlled via Agilent Digital Radio Communication tester (E5515C) to ensure the maximum power transmission and proper modulation. This result contains conducted output power for the EUT. In all cases, the measured peak output power should be greater and within 5% than EMI measurement. Table 12-1: The average conducted power measurement results for GSM900/1800 Average Conducted Power (dbm) GSM Channel 124(915MHz) Channel 37(897.4MHz) Channel 975(880.2MHz) 900MHz Average Conducted Power (dbm) GSM Channel 885(1785MHz) Channel 698(1747.8MHz) Channel 512(1710.2MHz) 1800MHz Table 12-2: The average conducted power measurement results for GPRS and EGPRS GSM 900 Measured Power (dbm) calculation Averaged Power (dbm) GPRS Txslot dB Txslots dB Txslots dB Txslots dB GSM 900 Measured Power (dbm) Averaged Power (dbm) EGPRS Txslot dB Txslots dB Txslots dB Txslots dB DCS1800 Measured Power (dbm) Averaged Power (dbm) GPRS Txslot dB Txslots dB Txslots dB Txslots dB DCS1800 Measured Power (dbm) Averaged Power (dbm) EGPRS Txslot dB Txslots dB Txslots dB Txslots dB East China Institute of Telecommunications Page Number : 38 of 299

39 NOTES: 1) Division Factors To average the power, the division factor is as follows: 1TX-slot = 1 transmit time slot out of 8 time slots=> conducted power divided by (8/1) => -9.03dB 2TX-slots = 2 transmit time slots out of 8 time slots=> conducted power divided by (8/2) => -6.02dB 3TX-slots = 3 transmit time slots out of 8 time slots=> conducted power divided by (8/3) => -4.26dB 4TX-slots = 4 transmit time slots out of 8 time slots=> conducted power divided by (8/4) => -3.01dB According to the conducted power as above, the body measurements are performed with 4Txslots for 900MHz, 1800MHz WCDMA Measurement result Table 12.3 The conducted Power for WCDMA band WCDMA BAND VIII result(dbm) Item ARFCN (882.4MHz) (897.4MHz) (912.6MHz) WCDMA \ HSDPA HSUPA band WCDMA BAND I result(dbm) Item ARFCN (1922.6MHz) (1950.0MHz) (1977.4MHz) WCDMA \ HSDPA HSUPA Note: HSDPA/HSUPA body SAR are not required, because maximum average output power of each RF channel with HSDPA/HSUPA active is not 1/4 db higher than that measured without HSDPA/HSUPA and the maximum SAR for WCDMA I and WCDMA VIII are not above 75% of the SAR limit. East China Institute of Telecommunications Page Number : 39 of 299

40 12.3. LTE Measurement result Table 12.4: The conducted power measurement results for LTE Band 3/7/8/20 Bandwidth Mode RB Size RB Offset Band3 Channel MHz Actual output power(dbm) Channel MHz Channel MHz QPSK MHz QAM Bandwidth Mode RB Size RB Offset Channel MHz Actual output power(dbm) Channel MHz Channel MHz QPSK MHz QAM East China Institute of Telecommunications Page Number : 40 of 299

41 Bandwidth Mode RB Size RB Offset 5MHz QPSK 16QAM Bandwidth Mode RB Size RB Offset Channel MHz Actual output power(dbm) Channel MHz Channel MHz Channel MHz Actual output power(dbm) Channel MHz Channel MHz MHz 16QAM QPSK East China Institute of Telecommunications Page Number : 41 of 299

42 Bandwidth Mode RB Size RB Offset 15MHz QPSK 16QAM Bandwidth Mode RB Size RB Offset 20MHz 16QAM QPSK Channel MHz Actual output power(dbm) Channel MHz Channel MHz Channel MHz Actual output power(dbm) Channel MHz Channel MHz East China Institute of Telecommunications Page Number : 42 of 299

43 Bandwidth Mode RB Size RB Offset 5MHz QPSK 16QAM Bandwidth Mode RB Size RB Offset 10MHz QPSK 16QAM Band7 Channel MHz Actual output power(dbm) Channel MHz East China Institute of Telecommunications Page Number : 43 of 299 Channel MHz Channel MHz Actual output power(dbm) Channel MHz Channel MHz

44 Bandwidth Mode RB Size RB Offset 15MHz QPSK 16QAM Bandwidth Mode RB Size RB Offset 20MHz QPSK 16QAM Channel MHz Actual output power(dbm) Channel MHz Channel MHz Channel MHz Actual output power(dbm) Channel MHz Channel MHz East China Institute of Telecommunications Page Number : 44 of 299

45 Bandwidth Mode RB Size RB Offset 1.4MHz QPSK 16QAM Bandwidth Mode RB Size RB Offset 3MHz QPSK 16QAM Band8 Channel MHz Actual output power(dbm) Channel MHz East China Institute of Telecommunications Page Number : 45 of 299 Channel MHz Channel MHz Actual output power(dbm) Channel MHz Channel MHz

46 Bandwidth Mode RB Size RB Offset 5MHz QPSK 16QAM Bandwidth Mode RB Size RB Offset 10MHz 16QAM QPSK Channel MHz Actual output power(dbm) Channel MHz Channel MHz Channel MHz Actual output power(dbm) Channel MHz Channel MHz East China Institute of Telecommunications Page Number : 46 of 299

47 Bandwidth Mode RB Size RB Offset QPSK Band20 Channel MHz Actual output power(dbm) Channel MHz Channel MHz MHz QAM Bandwidth Mode RB Size RB Offset Channel MHz Actual output power(dbm) Channel MHz Channel MHz MHz QPSK 16QAM East China Institute of Telecommunications Page Number : 47 of 299

48 Bandwidth Mode RB Size RB Offset 15MHz QPSK 16QAM Bandwidth Mode RB Size RB Offset 20MHz QPSK 16QAM Channel MHz Actual output power(dbm) Channel MHz Channel MHz Channel MHz Actual output power(dbm) Channel MHz Channel MHz East China Institute of Telecommunications Page Number : 48 of 299

49 12.4. BT and Wi-Fi Measurement result BLE Channel Peak Conducted Output Power(dBm) Peak Conducted Output Power(dBm) Peak Conducted Output Power(dBm) Channel Peak Conducted Output Power(dBm) Table 12.4: The output power of BT antenna Ch MHz Ch MHz Ch MHz Ch MHz Ch Mhz Ch MHz Table 12.5 The average conducted power for Wi-Fi The average conducted power for Wi-Fi is as following: b(dBm) Channel\data rate 1Mbps 2Mbps 5.5Mbps 11Mbps g(dBm) Channel\data rate 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps M n(dBm) Channel\data rate MCS0 MCS1 MCS2 MCS3 MCS4 MCS5 MCS6 MCS M n(dBm) Channel\data rate MCS0 MCS1 MCS2 MCS3 MCS4 MCS5 MCS6 MCS Note: According to the EN62479,Wi-Fi/BT SAR testing is required, when conducted power of Wi-Fi/BT>20mW. East China Institute of Telecommunications Page Number : 49 of 299

50 13. SAR Test Result Table 13-1: SAR Values (GSM 900 MHz Band-Head) Frequency Test SAR(10g) Power Mode/Band Side MHz Ch. Position (W/kg) Drift(dB) EGSM900 Left Touch EGSM900 Left Tilt EGSM900 Right Touch EGSM900 Right Tilt EGSM900 Right Touch EGSM900 Right Touch Table 13-2: SAR Values (GSM 900 MHz Band-Body) Frequency Test Spacing SAR(10g) Power Mode/Band Service/Headset MHz Ch. Position (mm) (W/kg) Drift(dB) GPRS 4TS Class12 Toward Ground GPRS 4TS Class12 Toward Phantom GPRS 4TS Class12 Toward Left GPRS 4TS Class12 Toward Right GPRS 4TS Class12 Toward Bottom GPRS 4TS Class12 Toward Ground GPRS 4TS Class12 Toward Ground E-GPRS Toward Class12 4TS Ground GSM900 Headset Toward Ground East China Institute of Telecommunications Page Number : 50 of 299

51 Table 13-3: SAR Values (GSM 1800 MHz Band-Head) Frequency Test SAR(10g) Power Mode/Band Side MHz Ch. Position (W/kg) Drift(dB) DCS1800 Left Touch DCS1800 Left Tilt DCS1800 Right Touch DCS1800 Right Tilt DCS1800 Right Touch DCS1800 Right Touch Table 13-4: SAR Values (GSM 1800 MHz Band-Body) Frequency Test Spacing SAR(10g) Power Mode/Band Service/Headset MHz Ch. Position (mm) (W/kg) Drift(dB) GPRS 4TS Class12 Toward Ground GPRS 4TS Class12 Toward Phantom GPRS 4TS Class12 Toward Left GPRS 4TS Class12 Toward Right GPRS 4TS Class12 Toward Bottom GPRS 4TS Class12 Toward Ground GPRS 4TS Class12 Toward Ground E-GPRS Toward Class12 4TS Ground DCS1800 Headset Toward Ground East China Institute of Telecommunications Page Number : 51 of 299

52 Table 13-5: SAR Values (WCDMA 2100 MHz Band-Head) Frequency Test SAR(10g) Power Mode/Band Side MHz Ch. Position (W/kg) Drift(dB) Band I Left Touch Band I Left Tilt Band I Right Touch Band I Right Tilt Band I Right Touch Band I Right Touch Table 13-6: SAR Values (WCDMA 2100 MHz Band-Body) Frequency Test Spacing SAR(10g) Power Mode/Band Service/Headset MHz Ch. Position (mm) (W/kg) Drift(dB) Band I 12.2kbps RMC Toward Ground Band I 12.2kbps RMC Toward Phantom Band I 12.2kbps RMC Toward Left Band I 12.2kbps RMC Toward Right Band I 12.2kbps RMC Toward Bottom Band I 12.2kbps RMC Toward Ground Band I 12.2kbps RMC Toward Ground Band I Headset Toward Ground East China Institute of Telecommunications Page Number : 52 of 299

53 Table 13-7: SAR Values (WCDMA BandⅧ-Head) Frequency Test SAR(10g) Power Mode/Band Side MHz Ch. Position (W/kg) Drift(dB) Band Ⅷ Left Touch Band Ⅷ Left Tilt Band Ⅷ Right Touch Band Ⅷ Right Tilt Band Ⅷ Right Touch Band Ⅷ Right Touch Table 13-8: SAR Values (WCDMA BandⅧ-Body) Frequency Test Spacing SAR(10g) Power Mode/Band Service/Headset MHz Ch. Position (mm) (W/kg) Drift(dB) Band Ⅷ 12.2kbps RMC Toward Ground Band Ⅷ 12.2kbps RMC Toward Phantom Band Ⅷ 12.2kbps RMC Toward Left Band Ⅷ 12.2kbps RMC Toward Right Band Ⅷ 12.2kbps RMC Toward Bottom Band Ⅷ 12.2kbps RMC Toward Ground Band Ⅷ 12.2kbps RMC Toward Ground Band Ⅷ Headset Toward Ground East China Institute of Telecommunications Page Number : 53 of 299

54 Table 13-9: SAR Values (LTE Band 3-Head) Frequency Test SAR(10g) Power Mode/Band Configuration Side MHz Ch. Position (W/kg) Drift(dB) Band 3 QPSK_3MHz_1RB_Middle Left Touch Band 3 QPSK_3MHz_1RB_Middle Left Tilt Band 3 QPSK_3MHz_1RB_Middle Right Touch Band 3 QPSK_3MHz_1RB_Middle Right Tilt Band 3 QPSK_3MHz_8RB_Middle Left Touch Band 3 QPSK_3MHz_8RB_Middle Left Tilt Band 3 QPSK_3MHz_8RB_Middle Right Touch Band 3 QPSK_3MHz_8RB_Middle Right Tilt Band 3 QPSK_3MHz_1RB_High Left Touch Band 3 QPSK_3MHz_1RB_Low Left Touch Band 3 QPSK_20MHz_1RB_High Left Touch Band 3 QPSK_15MHz_1RB_High Left Touch Band 3 QPSK_10MHz_1RB_High Left Touch Band 3 QPSK_5MHz_1RB_High Left Touch Band 3 QPSK_1.4MHz_1RB_High Left Touch East China Institute of Telecommunications Page Number : 54 of 299

55 Table 13-10: SAR Values (LTE Band 3-Body) Frequency Mode/B Test Spacing SAR(10g) Power Configuration MHz Ch. and Position (mm) (W/kg) Drift(dB) Band 3 QPSK_3MHz_1RB_Middle Band 3 QPSK_3MHz_1RB_Middle Band 3 QPSK_3MHz_1RB_Middle Band 3 QPSK_3MHz_1RB_Middle Band 3 QPSK_3MHz_1RB_Middle Band 3 QPSK_3MHz_8RB_Middle Band 3 QPSK_3MHz_8RB_Middle Band 3 QPSK_3MHz_8RB_Middle Band 3 QPSK_3MHz_8RB_Middle Band 3 QPSK_3MHz_8RB_Middle Band 3 QPSK_3MHz_1RB_High Band 3 QPSK_3MHz_1RB_Low Band 3 QPSK_20MHz_1RB_High Band 3 QPSK_15MHz_1RB_High Band 3 QPSK_10MHz_1RB_High Band 3 QPSK_5MHz_1RB_High Band 3 QPSK_1.4MHz_1RB_High Toward Ground Toward Phantom Toward Left Toward Right Toward Bottom Toward Ground Toward Phantom Toward Left Toward Right Toward Bottom Toward Ground Toward Ground Toward Ground Toward Ground Toward Ground Toward Ground Toward Ground East China Institute of Telecommunications Page Number : 55 of 299

56 Table 13-11: SAR Values (LTE Band 7-Head) Frequency Test SAR(10g) Power Mode/Band Configuration Side MHz Ch. Position (W/kg) Drift(dB) Band 3 QPSK_20MHz_1RB_High Left Touch Band 3 QPSK_20MHz_1RB_High Left Tilt Band 3 QPSK_20MHz_1RB_High Right Touch Band 3 QPSK_20MHz_1RB_High Right Tilt Band 3 QPSK_20MHz_50RB_High Left Touch Band 3 QPSK_20MHz_50RB_High Left Tilt Band 3 QPSK_20MHz_50RB_High Right Touch Band 3 QPSK_20MHz_50RB_High Right Tilt Band 3 QPSK_20MHz_1RB_Middle Left Touch Band 3 QPSK_20MHz_1RB_Low Left Touch Band 3 QPSK_15MHz_1RB_High Left Touch Band 3 QPSK_10MHz_1RB_High Left Touch Band 3 QPSK_5MHz_1RB_High Left Touch East China Institute of Telecommunications Page Number : 56 of 299

57 Table 13-12: SAR Values (LTE Band 7-Body) Frequency Mode/B Test Spacing SAR(10g) Power Configuration MHz Ch. and Position (mm) (W/kg) Drift(dB) Band 3 QPSK_20MHz_1RB_High Band 3 QPSK_20MHz_1RB_High Band 3 QPSK_20MHz_1RB_High Band 3 QPSK_20MHz_1RB_High Band 3 QPSK_20MHz_1RB_High Band 3 QPSK_20MHz_50RB_High Band 3 QPSK_20MHz_50RB_High Band 3 QPSK_20MHz_50RB_High Band 3 QPSK_20MHz_50RB_High Band 3 QPSK_20MHz_50RB_High Band 3 QPSK_20MHz_1RB_Middle Band 3 QPSK_20MHz_1RB_Low Band 3 QPSK_15MHz_1RB_High Band 3 QPSK_10MHz_1RB_High Band 3 QPSK_5MHz_1RB_High Toward Ground Toward Phantom Toward Left Toward Right Toward Bottom Toward Ground Toward Phantom Toward Left Toward Right Toward Bottom Toward Ground Toward Ground Toward Ground Toward Ground Toward Ground East China Institute of Telecommunications Page Number : 57 of 299

58 Table 13-9: SAR Values (LTE Band 8-Head) Frequency Test SAR(10g) Power Mode/Band Configuration Side MHz Ch. Position (W/kg) Drift(dB) Band 3 QPSK_5MHz_1RB_Middle Left Touch Band 3 QPSK_5MHz_1RB_Middle Left Tilt Band 3 QPSK_5MHz_1RB_Middle Right Touch Band 3 QPSK_5MHz_1RB_Middle Right Tilt Band 3 QPSK_5MHz_12RB_Middle Left Touch Band 3 QPSK_5MHz_12RB_Middle Left Tilt Band 3 QPSK_5MHz_12RB_Middle Right Touch Band 3 QPSK_5MHz_12RB_Middle Right Tilt Band 3 QPSK_5MHz_1RB_High Right Touch Band 3 QPSK_5MHz_1RB_Low Right Touch Band 3 QPSK_10MHz_1RB_Low Right Touch Band 3 QPSK_3MHz_1RB_Low Right Touch Band 3 QPSK_1.4MHz_1RB_Low Right Touch East China Institute of Telecommunications Page Number : 58 of 299

59 Table 13-10: SAR Values (LTE Band 8-Body) Frequency Mode/B Test Spacing SAR(10g) Power Configuration MHz Ch. and Position (mm) (W/kg) Drift(dB) Band 3 QPSK_5MHz_1RB_Middle Band 3 QPSK_5MHz_1RB_Middle Band 3 QPSK_5MHz_1RB_Middle Band 3 QPSK_5MHz_1RB_Middle Band 3 QPSK_5MHz_1RB_Middle Band 3 QPSK_5MHz_12RB_Middle Band 3 QPSK_5MHz_12RB_Middle Band 3 QPSK_5MHz_12RB_Middle Band 3 QPSK_5MHz_12RB_Middle Band 3 QPSK_5MHz_12RB_Middle Band 3 QPSK_5MHz_1RB_High Band 3 QPSK_5MHz_1RB_Low Band 3 QPSK_10MHz_1RB_Middle Band 3 QPSK_3MHz_1RB_Middle Band 3 QPSK_1.4MHz_1RB_Middle Toward Ground Toward Phantom Toward Left Toward Right Toward Bottom Toward Ground Toward Phantom Toward Left Toward Right Toward Bottom Toward Ground Toward Ground Toward Ground Toward Ground Toward Ground East China Institute of Telecommunications Page Number : 59 of 299

60 Table 13-9: SAR Values (LTE Band 20-Head) Frequency Test SAR(10g) Power Mode/Band Configuration Side MHz Ch. Position (W/kg) Drift(dB) Band 3 QPSK_5MHz_1RB_High Left Touch Band 3 QPSK_5MHz_1RB_High Left Tilt Band 3 QPSK_5MHz_1RB_High Right Touch Band 3 QPSK_5MHz_1RB_High Right Tilt Band 3 QPSK_5MHz_12RB_High Left Touch Band 3 QPSK_5MHz_12RB_High Left Tilt Band 3 QPSK_5MHz_12RB_High Right Touch Band 3 QPSK_5MHz_12RB_High Right Tilt Band 3 QPSK_5MHz_1RB_Middle Right Touch Band 3 QPSK_5MHz_1RB_Low Right Touch Band 3 QPSK_20MHz_1RB_High Right Touch Band 3 QPSK_15MHz_1RB_High Right Touch Band 3 QPSK_10MHz_1RB_High Right Touch East China Institute of Telecommunications Page Number : 60 of 299

61 Table 13-10: SAR Values (LTE Band 20-Body) Frequency Mode/B Test Spacing SAR(10g) Power Configuration MHz Ch. and Position (mm) (W/kg) Drift(dB) Band 3 QPSK_5MHz_1RB_High Band 3 QPSK_5MHz_1RB_High Band 3 QPSK_5MHz_1RB_High Band 3 QPSK_5MHz_1RB_High Band 3 QPSK_5MHz_1RB_High Band 3 QPSK_5MHz_12RB_High Band 3 QPSK_5MHz_12RB_High Band 3 QPSK_5MHz_12RB_High Band 3 QPSK_5MHz_12RB_High Band 3 QPSK_5MHz_12RB_High Band 3 QPSK_5MHz_1RB_Middle Band 3 QPSK_5MHz_1RB_Low Band 3 QPSK_20MHz_1RB_High Band 3 QPSK_15MHz_1RB_High Band 3 QPSK_10MHz_1RB_High Toward Ground Toward Phantom Toward Left Toward Right Toward Bottom Toward Ground Toward Phantom Toward Left Toward Right Toward Bottom Toward Ground Toward Ground Toward Ground Toward Ground Toward Ground East China Institute of Telecommunications Page Number : 61 of 299

62 14. Measurement Uncertainty Measurement uncertainty evaluation for SAR test Error Description Unc. value, ±% Prob. Dist. Div. Measurement System c i c i Std.Unc. Std.Unc. 1g 10g ±%,1g ±%,10g Probe Calibration 6.0 N Axial Isotropy 0.5 R Hemispherical Isotropy 2.6 R Boundary Effects 0.8 R Linearity 0.6 R System Detection Limits 1.0 R Readout Electronics 0.7 N Response Time 0 R Integration Time 2.6 R RF Ambient Noise 3.0 R RF Ambient Reflections 3.0 R Probe Positioner 1.5 R Probe Positioning 2.9 R Max. SAR Eval. 1.0 R Test Sample Related Device Positioning 2.9 N Device Holder 3.6 N Phantom and Setup Phantom Uncertainty 4.0 R Liquid Conductivity 5.0 R (target) Liquid Conductivity 2.5 N (meas.) Liquid Permittivity 5.0 R (target) Liquid Permittivity 2.5 N (meas.) V i v eff East China Institute of Telecommunications Page Number : 62 of 299

63 Measurement uncertainty evaluation for system validation Error Description Unc. value, ±% Prob. Dist. Div. Measurement System c i c i Std.Unc. Std.Unc. 1g 10g ±%,1g ±%,10g Probe Calibration 6.0 N Axial Isotropy 0.5 R Hemispherical Isotropy 2.6 R Boundary Effects 0.8 R Linearity 0.6 R System Detection Limits 1.0 R Readout Electronics 0.7 N Response Time 0 R Integration Time 2.6 R RF Ambient Noise 3.0 R RF Ambient Reflections 3.0 R Probe Positioner 1.5 R Probe Positioning 2.9 R Max. SAR Eval. 1.0 R Diople Power Drift 5.0 R Dipole Positioning 2.0 N Dipole Input Power 5.0 N Phantom and Setup Phantom Uncertainty 4.0 R Liquid Conductivity 5.0 R (target) Liquid Conductivity 2.5 N (meas.) Liquid Permittivity 5.0 R (target) Liquid Permittivity 2.5 N (meas.) V i v eff Combined Std Uncertainty Expanded Std Uncertainty ±11.2% ±10.9% 387 ±22.4% ±21.8% East China Institute of Telecommunications Page Number : 63 of 299

64 15. MAIN TEST INSTRUMENTS Table 15.1: List of Main Instruments No. Name Type Serial Number Calibration Date Valid Period 01 Network analyzer N5242A MY Jan 07, 2015 One year 02 Power meter NRVD Power sensor NRV-Z , Jul 07, 2014 One year 04 Signal Generator E4438C MY Jan 07, 2015 One Year 05 Amplifier NTWPA F No Calibration Requested 06 Coupler 778D MY Jul 25, 2014 One year 07 BTS E5515C MY Jan 07, 2015 One year 08 E-field Probe ES3DV Nov 04, 2014 One year 09 DAE SPEAG DAE Oct 14, 2014 One year SPEAG D835V2 4d112 Nov 04, 2014 One year SPEAG D900V2 1d109 Oct 09, 2014 One year 10 Dipole Validation Kit SPEAG D1750V Nov 06, 2014 One year SPEAG D1900V2 5d134 Nov 05, 2014 One year SPEAG D2600V Nov One year ***END OF REPORT BODY*** East China Institute of Telecommunications Page Number : 64 of 299

65 ANNEX A. GRAPH RESULTS GSM900 Left Cheek Middle Date/Time: 01/07/2015 Medium: Head 900MHz Medium parameters used (interpolated): f = MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: GSM 900MHz; Frequency: MHz; Duty Cycle: 1:8.3 Probe: ES3DV3 - SN3252ConvF(6.2, 6.2, 6.2) Middle Cheek Left GSM900MHz/Area Scan (12x7x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = mw/g Middle Cheek Left GSM900MHz/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = 0.12 db Peak SAR (extrapolated) = mw/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 65 of 299

66 GSM900 Left Tilt Middle Date/Time: 01/07/2015 Medium: Head 900MHz Medium parameters used (interpolated): f = MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: GSM 900MHz; Frequency: MHz; Duty Cycle: 1:8.3 Probe: ES3DV3 - SN3252ConvF(6.2, 6.2, 6.2) Middle Tilt Left GSM900MHz/Area Scan (12x7x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = mw/g Middle Tilt Left GSM900MHz/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = db Peak SAR (extrapolated) = mw/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 66 of 299

67 GSM900 Right Cheek Middle Date/Time: 01/06/2015 Medium: Head 900MHz Medium parameters used (interpolated): f = MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: GSM 900MHz; Frequency: MHz; Duty Cycle: 1:8.3 Probe: ES3DV3 - SN3252ConvF(6.2, 6.2, 6.2) Middle Cheek Right GSM900MHz/Area Scan (7x12x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = mw/g Middle Cheek Right GSM900MHz/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = db Peak SAR (extrapolated) = mW/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 67 of 299

68 GSM900 Right Tilt Middle Date/Time: 01/07/2015 Medium: Head 900MHz Medium parameters used (interpolated): f = MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: GSM 900MHz; Frequency: MHz; Duty Cycle: 1:8.3 Probe: ES3DV3 - SN3252ConvF(6.2, 6.2, 6.2) Middle Tilt Right GSM900MHz/Area Scan (7x12x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = mw/g Middle Tilt Right GSM900MHz/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = 0.07 db Peak SAR (extrapolated) = mW/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 68 of 299

69 GSM900 Right Cheek High Date/Time: 01/07/2015 Medium: Head 900MHz Medium parameters used: f = 915 MHz; σ = mho/m;εr = 41.21; ρ = 1000 kg/m3 Communication System: GSM 900MHz; Frequency: MHz; Duty Cycle: 1:8.3 Probe: ES3DV3 - SN3252ConvF(6.2, 6.2, 6.2) High Cheek Right GSM900MHz/Area Scan (7x12x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = mw/g High Cheek Right GSM900MHz/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = db Peak SAR (extrapolated) = mW/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 69 of 299

70 GSM900 Right Cheek Low Date/Time: 01/07/2015 Medium: Head 900MHz Medium parameters used (interpolated): f = MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: GSM 900MHz; Frequency: MHz; Duty Cycle: 1:8.3 Probe: ES3DV3 - SN3252ConvF(6.2, 6.2, 6.2) Low Cheek Right GSM900MHz/Area Scan (7x12x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = mw/g Low Cheek Right GSM900MHz/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = db Peak SAR (extrapolated) = mW/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 70 of 299

71 GSM900 Body Toward Ground GPRS 4TS Middle Date/Time: 01/07/2015 Medium: Head 900MHz Medium parameters used (interpolated): f = MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: GSM 900MHz GPRS 4TS; Frequency: MHz; Duty Cycle: 1:2 Probe: ES3DV3 - SN3252ConvF(6.2, 6.2, 6.2) Middle Toward Ground GPRS 4TS 900MHz/Area Scan (10x16x1): Measurement grid: dx=10mm, dy=10mm Maximum value of SAR (measured) = mw/g Middle Toward Ground GPRS 4TS 900MHz/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = 0.14 db Peak SAR (extrapolated) = mw/g SAR(1 g) = 1.08 mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 71 of 299

72 GSM900 Body Toward Phantom GPRS 4TS Middle Date/Time: 01/07/2015 Medium: Head 900MHz Medium parameters used (interpolated): f = MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: GSM 900MHz GPRS 4TS; Frequency: MHz; Duty Cycle: 1:2 Probe: ES3DV3 - SN3252ConvF(6.2, 6.2, 6.2) Middle Toward Phantom GPRS 4TS 900MHz/Area Scan (10x16x1): Measurement grid: dx=10mm, dy=10mm Maximum value of SAR (measured) = mw/g Middle Toward Phantom GPRS 4TS 900MHz/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = 0.06 db Peak SAR (extrapolated) = mw/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 72 of 299

73 GSM900 Body Left GPRS 4TS Middle Date/Time: 01/07/2015 Medium: Head 900MHz Medium parameters used (interpolated): f = MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: GSM 900MHz GPRS 4TS; Frequency: MHz; Duty Cycle: 1:2 Probe: ES3DV3 - SN3252ConvF(6.2, 6.2, 6.2) Middle Left GPRS 4TS 900MHz/Area Scan (5x16x1): Measurement grid: dx=10mm, dy=10mm Middle Left GPRS 4TS 900MHz/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = db Peak SAR (extrapolated) = mw/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 73 of 299

74 GSM900 Body Right GPRS 4TS Middle Date/Time: 01/07/2015 Medium: Head 900MHz Medium parameters used (interpolated): f = MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: GSM 900MHz GPRS 4TS; Frequency: MHz; Duty Cycle: 1:2 Probe: ES3DV3 - SN3252ConvF(6.2, 6.2, 6.2) Middle Right GPRS 4TS 900MHz/Area Scan (5x16x1): Measurement grid: dx=10mm, dy=10mm Maximum value of SAR (measured) = mw/g Middle Right GPRS 4TS 900MHz/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = db Peak SAR (extrapolated) = mw/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 74 of 299

75 GSM900 Body Bottom GPRS 4TS Middle Date/Time: 01/07/2015 Medium: Head 900MHz Medium parameters used (interpolated): f = MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: GSM 900MHz GPRS 4TS; Frequency: MHz; Duty Cycle: 1:2 Probe: ES3DV3 - SN3252ConvF(6.2, 6.2, 6.2) Middle Bottom GPRS 4TS 900MHz/Area Scan (5x11x1): Measurement grid: dx=10mm, dy=10mm Maximum value of SAR (measured) = mw/g Middle Bottom GPRS 4TS 900MHz/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = 0.07 db Peak SAR (extrapolated) = mw/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 75 of 299

76 GSM900 Body Toward Ground GPRS 4TS High Date/Time: 01/07/2015 Medium: Head 900MHz Medium parameters used: f = 915 MHz; σ = mho/m;εr = 41.21; ρ = 1000 kg/m3 Communication System: GSM 900MHz GPRS 4TS; Frequency: MHz; Duty Cycle: 1:2 Probe: ES3DV3 - SN3252ConvF(6.2, 6.2, 6.2) High Toward Ground GPRS 4TS 900MHz/Area Scan (10x16x1): Measurement grid: dx=10mm, dy=10mm Maximum value of SAR (measured) = mw/g High Toward Ground GPRS 4TS 900MHz/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = 0.04 db Peak SAR (extrapolated) = mw/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 76 of 299

77 GSM900 Body Toward Ground GPRS 4TS Low Date/Time: 01/07/2015 Medium: Head 900MHz Medium parameters used (interpolated): f = MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: GSM 900MHz GPRS 4TS; Frequency: MHz; Duty Cycle: 1:2 Probe: ES3DV3 - SN3252ConvF(6.2, 6.2, 6.2) Low Toward Ground GPRS 4TS 900MHz/Area Scan (10x16x1): Measurement grid: dx=10mm, dy=10mm Maximum value of SAR (measured) = mw/g Low Toward Ground GPRS 4TS 900MHz/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = 0.09 db Peak SAR (extrapolated) = mW/g SAR(1 g) = 1.16 mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 77 of 299

78 GSM900 Body Toward Ground E-GPRS 4TS Low Date/Time: 01/07/2015 Medium: Head 900MHz Medium parameters used (interpolated): f = MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: GSM 900MHz E-GPRS 4TS; Frequency: MHz; Duty Cycle: 1:8.7 Probe: ES3DV3 - SN3252ConvF(6.2, 6.2, 6.2) Low Toward Ground E-GPRS 4TS 900MHz/Area Scan (10x16x1): Measurement grid: dx=10mm, dy=10mm Maximum value of SAR (measured) = mw/g Low Toward Ground E-GPRS 4TS 900MHz/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = db Peak SAR (extrapolated) = mW/g SAR(1 g) = 1.3 mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 78 of 299

79 GSM900 Body Toward Ground Low With Headset Date/Time: 01/07/2015 Medium: Head 900MHz Medium parameters used (interpolated): f = MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: GSM 900MHz; Frequency: MHz; Duty Cycle: 1:8.3 Probe: ES3DV3 - SN3252ConvF(6.2, 6.2, 6.2) Low Toward Ground GSM900MHz With Headset/Area Scan (10x16x1): Measurement grid: dx=10mm, dy=10mm Maximum value of SAR (measured) = mw/g Low Toward Ground GSM900MHz With Headset/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = db Peak SAR (extrapolated) = mW/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 79 of 299

80 GSM1800 Left Cheek Middle Date/Time: 01/08/2015 Medium: Head 1800MHz Medium parameters used (interpolated): f = MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: GSM 1800MHz; Frequency: MHz; Duty Cycle: 1:8.3 Probe: ES3DV3 - SN3252ConvF(5.24, 5.24, 5.24); Middle Cheek Left GSM1800MHz/Area Scan (11x7x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = mw/g Middle Cheek Left GSM1800MHz/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = db Peak SAR (extrapolated) = mw/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 80 of 299

81 GSM1800 Left Tilt Middle Date/Time: 01/08/2015 Medium: Head 1800MHz Medium parameters used (interpolated): f = MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: GSM 1800MHz; Frequency: MHz; Duty Cycle: 1:8.3 Probe: ES3DV3 - SN3252ConvF(5.24, 5.24, 5.24); Middle Tilt Left GSM1800MHz/Area Scan (11x7x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = mw/g Middle Tilt Left GSM1800MHz/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = 0.09 db Peak SAR (extrapolated) = mw/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 81 of 299

82 GSM1800 Right Cheek Middle Date/Time: 01/08/2015 Medium: Head 1800MHz Medium parameters used (interpolated): f = MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: GSM 1800MHz; Frequency: MHz; Duty Cycle: 1:8.3 Probe: ES3DV3 - SN3252ConvF(5.24, 5.24, 5.24); Middle Cheek Right GSM1800MHz/Area Scan (7x11x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = mw/g Middle Cheek Right GSM1800MHz/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = db Peak SAR (extrapolated) = mw/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 82 of 299

83 GSM1800 Right Tilt Middle Date/Time: 01/08/2015 Medium: Head 1800MHz Medium parameters used (interpolated): f = MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: GSM 1800MHz; Frequency: MHz; Duty Cycle: 1:8.3 Probe: ES3DV3 - SN3252ConvF(5.24, 5.24, 5.24); Middle Tilt Right GSM1800MHz/Area Scan (7x11x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = mw/g Middle Tilt Right GSM1800MHz/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = 0.10 db Peak SAR (extrapolated) = mw/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = 0.108mW/g East China Institute of Telecommunications Page Number : 83 of 299

84 GSM1800 Right Cheek High Date/Time: 01/08/2015 Medium: Head 1800MHz Medium parameters used: f = 1785 MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: GSM 1800MHz; Frequency: MHz; Duty Cycle: 1:8.3 Probe: ES3DV3 - SN3252ConvF(5.24, 5.24, 5.24); High Cheek Right GSM1800MHz/Area Scan (7x11x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = mw/g High Cheek Right GSM1800MHz/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = db Peak SAR (extrapolated) = mW/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 84 of 299

85 GSM1800 Right Cheek Low Date/Time: 01/08/2015 Medium: Head 1800MHz Medium parameters used (interpolated): f = MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: GSM 1800MHz; Frequency: MHz; Duty Cycle: 1:8.3 Probe: ES3DV3 - SN3252ConvF(5.24, 5.24, 5.24); Low Cheek Right GSM1800MHz/Area Scan (7x11x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = mw/g Low Cheek Right GSM1800MHz/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = 0.08 db Peak SAR (extrapolated) = mW/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 85 of 299

86 GSM1800 Body Toward Ground GPRS 4TS Middle Date/Time: 01/08/2015 Medium: Head 1800MHz Medium parameters used (interpolated): f = MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: GSM 1800MHz GPRS 4TS; Frequency: MHz; Duty Cycle: 1:2.7 Probe: ES3DV3 - SN3252ConvF(5.24, 5.24, 5.24); Middle Toward Phantom GPRS 4TS 1800MHz/Area Scan (10x16x1): Measurement grid: dx=10mm, dy=10mm Maximum value of SAR (measured) = mw/g Middle Toward Phantom GPRS 4TS 1800MHz/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = db Peak SAR (extrapolated) = mw/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 86 of 299

87 GSM1800 Body Toward Phantom GPRS 4TS Middle Date/Time: 01/08/2015 Medium: Head 1800MHz Medium parameters used (interpolated): f = MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: GSM 1800MHz GPRS 4TS; Frequency: MHz; Duty Cycle: 1:2.7 Probe: ES3DV3 - SN3252ConvF(5.24, 5.24, 5.24); Middle Toward Ground GPRS 4TS 1800MHz/Area Scan (10x16x1): Measurement grid: dx=10mm, dy=10mm Maximum value of SAR (measured) = mw/g Middle Toward Ground GPRS 4TS 1800MHz/Zoom Scan (7x7x7) /Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = db Peak SAR (extrapolated) = mW/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 87 of 299

88 GSM1800 Body Left GPRS 4TS Middle Date/Time: 01/08/2015 Medium: Head 1800MHz Medium parameters used (interpolated): f = MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: GSM 1800MHz GPRS 4TS; Frequency: MHz; Duty Cycle: 1:2.7 Probe: ES3DV3 - SN3252ConvF(5.24, 5.24, 5.24); Middle Left GPRS 4TS 1800MHz/Area Scan (5x16x1): Measurement grid: dx=10mm, dy=10mm Maximum value of SAR (measured) = mw/g Middle Left GPRS 4TS 1800MHz/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = db Peak SAR (extrapolated) = mW/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 88 of 299

89 GSM1800 Body Right GPRS 4TS Middle Date/Time: 01/08/2015 Medium: Head 1800MHz Medium parameters used (interpolated): f = MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: GSM 1800MHz GPRS 4TS; Frequency: MHz; Duty Cycle: 1:2.7 Probe: ES3DV3 - SN3252ConvF(5.24, 5.24, 5.24); Middle Right GPRS 4TS 1800MHz/Area Scan (5x16x1): Measurement grid: dx=10mm, dy=10mm Maximum value of SAR (measured) = mw/g Middle Right GPRS 4TS 1800MHz/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = db Peak SAR (extrapolated) = mW/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 89 of 299

90 GSM1800 Body Bottom GPRS 4TS Middle Date/Time: 01/08/2015 Medium: Head 1800MHz Medium parameters used (interpolated): f = MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: GSM 1800MHz GPRS 4TS; Frequency: MHz; Duty Cycle: 1:2.7 Probe: ES3DV3 - SN3252ConvF(5.24, 5.24, 5.24); Middle Bottom GPRS 4TS 1800MHz/Area Scan (5x11x1): Measurement grid: dx=10mm, dy=10mm Maximum value of SAR (measured) = mw/g Middle Bottom GPRS 4TS 1800MHz/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = db Peak SAR (extrapolated) = mW/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 90 of 299

91 GSM1800 Body Toward Ground GPRS 4TS High Date/Time: 01/08/2015 Medium: Head 1800MHz Medium parameters used: f = 1785 MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: GSM 1800MHz GPRS 4TS; Frequency: MHz; Duty Cycle: 1:2.7 Probe: ES3DV3 - SN3252ConvF(5.24, 5.24, 5.24); High Toward Ground GPRS 4TS 1800MHz/Area Scan (10x16x1): Measurement grid: dx=10mm, dy=10mm Maximum value of SAR (measured) = mw/g High Toward Ground GPRS 4TS 1800MHz/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = 0.05 db Peak SAR (extrapolated) = mW/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 91 of 299

92 GSM1800 Body Toward Ground GPRS 4TS Low Date/Time: 01/08/2015 Medium: Head 1800MHz Medium parameters used (interpolated): f = MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: GSM 1800MHz GPRS 4TS; Frequency: MHz; Duty Cycle: 1:2.7 Probe: ES3DV3 - SN3252ConvF(5.24, 5.24, 5.24); Low Toward Ground GPRS 4TS 1800MHz/Area Scan (10x16x1): Measurement grid: dx=10mm, dy=10mm Maximum value of SAR (measured) = mw/g Low Toward Ground GPRS 4TS 1800MHz/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = 0.06 db Peak SAR (extrapolated) = mW/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 92 of 299

93 GSM1800 Body Toward Ground E-GPRS 4TS Low Date/Time: 01/08/2015 Medium: Head 1800MHz Medium parameters used (interpolated): f = MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: GSM 1800MHz E-GPRS 4TS; Frequency: MHz; Duty Cycle: 1:8.7 Probe: ES3DV3 - SN3252ConvF(5.24, 5.24, 5.24); Low Toward Ground E-GPRS 4TS 1800MHz/Area Scan (10x16x1): Measurement grid: dx=10mm, dy=10mm Maximum value of SAR (measured) = mw/g Low Toward Ground E-GPRS 4TS 1800MHz/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = db Peak SAR (extrapolated) = 0.960mW/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 93 of 299

94 GSM1800 Body Toward Ground Low With Headset Date/Time: 01/08/2015 Medium: Head 1800MHz Medium parameters used (interpolated): f = MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: GSM 1800MHz (0); Frequency: MHz; Duty Cycle: 1:8.3 Probe: ES3DV3 - SN3252ConvF(5.24, 5.24, 5.24); Low Toward Ground GSM1800MHz With Headset/Area Scan (10x16x1): Measurement grid: dx=10mm, dy=10mm Maximum value of SAR (measured) = mw/g Low Toward Ground GSM1800MHz With Headset/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = 0.08 db Peak SAR (extrapolated) = mW/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 94 of 299

95 WCDMA Band I Left Cheek Middle Date/Time: 01/12/2015 Medium: Head 1950MHz Medium parameters used: f = 1950 MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: WCDMA Band I; Frequency: 1950 MHz; Duty Cycle: 1:1 Probe: ES3DV3 - SN3252ConvF(4.89, 4.89, 4.89); Middle Cheek Left WCDMA Band I/Area Scan (12x7x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = mw/g Middle Cheek Left WCDMA Band I/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = 0.05 db Peak SAR (extrapolated) = mw/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 95 of 299

96 WCDMA Band I Left Tilt Middle Date/Time: 01/12/2015 Medium: Head 1950MHz Medium parameters used: f = 1950 MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: WCDMA Band I; Frequency: 1950 MHz; Duty Cycle: 1:1 Probe: ES3DV3 - SN3252ConvF(4.89, 4.89, 4.89); Middle Tilt Left WCDMA Band I/Area Scan (12x7x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = mw/g Middle Tilt Left WCDMA Band I/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = db Peak SAR (extrapolated) = mw/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 96 of 299

97 WCDMA Band I Right Cheek Middle Date/Time: 01/12/2015 Medium: Head 1950MHz Medium parameters used: f = 1950 MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: WCDMA Band I; Frequency: 1950 MHz; Duty Cycle: 1:1 Probe: ES3DV3 - SN3252ConvF(4.89, 4.89, 4.89); Middle Cheek Right WCDMA Band I/Area Scan (7x12x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = mw/g Middle Cheek Right WCDMA Band I/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = db Peak SAR (extrapolated) = mW/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 97 of 299

98 WCDMA Band I Right Tilt Middle Date/Time: 01/12/2015 Medium: Head 1950MHz Medium parameters used: f = 1950 MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: WCDMA Band I; Frequency: 1950 MHz; Duty Cycle: 1:1 Probe: ES3DV3 - SN3252ConvF(4.89, 4.89, 4.89); Middle Tilt Right WCDMA Band I/Area Scan (7x12x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = mw/g Middle Tilt Right WCDMA Band I/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = 0.07 db Peak SAR (extrapolated) = mW/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 98 of 299

99 WCDMA Band I Right Cheek High Date/Time: 01/12/2015 Medium: Head 1950MHz Medium parameters used: f = 1978 MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: WCDMA Band I; Frequency: MHz; Duty Cycle: 1:1 Probe: ES3DV3 - SN3252ConvF(4.89, 4.89, 4.89); High Cheek Right WCDMA Band I/Area Scan (7x12x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = mw/g High Cheek Right WCDMA Band I/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = db Peak SAR (extrapolated) = mW/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 99 of 299

100 WCDMA Band I Right Cheek Low Date/Time: 01/12/2015 Medium: Head 1950MHz Medium parameters used (interpolated): f = MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: WCDMA Band I; Frequency: MHz; Duty Cycle: 1:1 Probe: ES3DV3 - SN3252ConvF(4.89, 4.89, 4.89); Low Cheek Right WCDMA Band I/Area Scan (7x12x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = mw/g Low Cheek Right WCDMA Band I/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = 0.12 db Peak SAR (extrapolated) = mW/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 100 of 299

101 WCDMA Band I Body Toward Ground Middle Date/Time: 01/12/2015 Medium: Head 1950MHz Medium parameters used: f = 1950 MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: WCDMA Band I; Frequency: 1950 MHz; Duty Cycle: 1:1 Probe: ES3DV3 - SN3252ConvF(4.89, 4.89, 4.89); Middle Toward Ground WCDMA Band I/Area Scan (10x17x1): Measurement grid: dx=10mm, dy=10mm Maximum value of SAR (measured) = mw/g Middle Toward Ground WCDMA Band I/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = db Peak SAR (extrapolated) = mw/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 101 of 299

102 WCDMA Band I Body Toward Phantom Middle Date/Time: 01/12/2015 Medium: Head 1950MHz Medium parameters used: f = 1950 MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: WCDMA Band I; Frequency: 1950 MHz; Duty Cycle: 1:1 Probe: ES3DV3 - SN3252ConvF(4.89, 4.89, 4.89); Middle Toward Phantom WCDMA Band I/Area Scan (10x17x1): Measurement grid: dx=10mm, dy=10mm Maximum value of SAR (measured) = mw/g Middle Toward Phantom WCDMA Band I/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = 0.01 db Peak SAR (extrapolated) = mw/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 102 of 299

103 WCDMA Band I Body Left Middle Date/Time: 01/12/2015 Medium: Head 1950MHz Medium parameters used: f = 1950 MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: WCDMA Band I; Frequency: 1950 MHz; Duty Cycle: 1:1 Probe: ES3DV3 - SN3252ConvF(4.89, 4.89, 4.89); Middle Left WCDMA Band I/Area Scan (5x17x1): Measurement grid: dx=10mm, dy=10mm Maximum value of SAR (measured) = mw/g Middle Left WCDMA Band I/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = db Peak SAR (extrapolated) = mw/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 103 of 299

104 WCDMA Band I Body Right Middle Date/Time: 01/12/2015 Medium: Head 1950MHz Medium parameters used: f = 1950 MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: WCDMA Band I; Frequency: 1950 MHz; Duty Cycle: 1:1 Probe: ES3DV3 - SN3252ConvF(4.89, 4.89, 4.89); Middle Right WCDMA Band I/Area Scan (5x17x1): Measurement grid: dx=10mm, dy=10mm Maximum value of SAR (measured) = mw/g Middle Right WCDMA Band I/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = 0.06 db Peak SAR (extrapolated) = mw/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 104 of 299

105 WCDMA Band I Body Bottom Middle Date/Time: 01/12/2015 Medium: Head 1950MHz Medium parameters used: f = 1950 MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: WCDMA Band I; Frequency: 1950 MHz; Duty Cycle: 1:1 Probe: ES3DV3 - SN3252ConvF(4.89, 4.89, 4.89); Middle Bottom WCDMA Band I/Area Scan (5x11x1): Measurement grid: dx=10mm, dy=10mm Maximum value of SAR (measured) = mw/g Middle Bottom WCDMA Band I/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = db Peak SAR (extrapolated) = mw/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 105 of 299

106 WCDMA Band I Body Toward Ground High Date/Time: 01/12/2015 Medium: Head 1950MHz Medium parameters used: f = 1978 MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: WCDMA Band I; Frequency: MHz; Duty Cycle: 1:1 Probe: ES3DV3 - SN3252ConvF(4.89, 4.89, 4.89); High Toward Ground WCDMA Band I/Area Scan (10x17x1): Measurement grid: dx=10mm, dy=10mm Maximum value of SAR (measured) = mw/g High Toward Ground WCDMA Band I/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = 0.14 db Peak SAR (extrapolated) = mw/g SAR(1 g) = 1.06 mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 106 of 299

107 WCDMA Band I Body Toward Ground Low Date/Time: 01/12/2015 Medium: Head 1950MHz Medium parameters used (interpolated): f = MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: WCDMA Band I; Frequency: MHz; Duty Cycle: 1:1 Probe: ES3DV3 - SN3252ConvF(4.89, 4.89, 4.89); Low Toward Ground WCDMA Band I/Area Scan (10x17x1): Measurement grid: dx=10mm, dy=10mm Maximum value of SAR (measured) = mw/g Low Toward Ground WCDMA Band I/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = 0.09 db Peak SAR (extrapolated) = mw/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 107 of 299

108 WCDMA Band I Body Toward Ground High With Headset Date/Time: 01/12/2015 Medium: Head 1950MHz Medium parameters used: f = 1978 MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: WCDMA Band I; Frequency: MHz; Duty Cycle: 1:1 Probe: ES3DV3 - SN3252ConvF(4.89, 4.89, 4.89); High Toward Ground WCDMA Band I With Headset/Area Scan (10x17x1): Measurement grid: dx=10mm, dy=10mm Maximum value of SAR (measured) = mw/g High Toward Ground WCDMA Band I With Headset/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = 0.03 db Peak SAR (extrapolated) = mw/g SAR(1 g) = 1.11 mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 108 of 299

109 WCDMA Band VIII Left Cheek Middle Date/Time: 01/07/2015 Medium: Head 900MHz Medium parameters used: f = 898 MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: WCDMA BAND VIII; Frequency: MHz; Duty Cycle: 1:2.2 Probe: ES3DV3 - SN3252ConvF(6.2, 6.2, 6.2) Middle Cheek Left WCDMA Band VIII/Area Scan (11x7x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = mw/g Middle Cheek Left WCDMA Band VIII/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = db Peak SAR (extrapolated) = mw/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 109 of 299

110 WCDMA Band VIII Left Tilt Middle Date/Time: 01/07/2015 Medium: Head 900MHz Medium parameters used: f = 898 MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: WCDMA BAND VIII; Frequency: MHz; Duty Cycle: 1:2.2 Probe: ES3DV3 - SN3252ConvF(6.2, 6.2, 6.2) Middle Tilt Left WCDMA Band VIII/Area Scan (11x7x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = mw/g Middle Tilt Left WCDMA Band VIII/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = 0.07 db Peak SAR (extrapolated) = mw/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 110 of 299

111 WCDMA Band VIII Right Cheek Middle Date/Time: 01/07/2015 Medium: Head 900MHz Medium parameters used: f = 898 MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: WCDMA BAND VIII; Frequency: MHz; Duty Cycle: 1:2.2 Probe: ES3DV3 - SN3252ConvF(6.2, 6.2, 6.2) Middle Cheek Right WCDMA Band VIII/Area Scan (7x11x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = mw/g Middle Cheek Right WCDMA Band VIII/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = db Peak SAR (extrapolated) = mw/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 111 of 299

112 WCDMA Band VIII Right Tilt Middle Date/Time: 01/07/2015 Medium: Head 900MHz Medium parameters used: f = 898 MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: WCDMA BAND VIII; Frequency: MHz; Duty Cycle: 1:2.2 Probe: ES3DV3 - SN3252ConvF(6.2, 6.2, 6.2) Middle Tilt Right WCDMA Band VIII/Area Scan (7x11x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = mw/g Middle Tilt Right WCDMA Band VIII/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = db Peak SAR (extrapolated) = mw/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 112 of 299

113 WCDMA Band VIII Right Cheek High Date/Time: 01/07/2015 Medium: Head 900MHz Medium parameters used: f = 913 MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: WCDMA BAND VIII; Frequency: MHz; Duty Cycle: 1:2.2 Probe: ES3DV3 - SN3252ConvF(6.2, 6.2, 6.2) High Cheek Right WCDMA Band VIII/Area Scan (7x11x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = mw/g High Cheek Right WCDMA Band VIII/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = 0.15 db Peak SAR (extrapolated) = mw/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 113 of 299

114 WCDMA Band VIII Right Cheek Low Date/Time: 01/07/2015 Medium: Head 900MHz Medium parameters used (interpolated): f = MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: WCDMA BAND VIII; Frequency: MHz; Duty Cycle: 1:2.2 Probe: ES3DV3 - SN3252ConvF(6.2, 6.2, 6.2) Low Cheek Right WCDMA Band VIII/Area Scan (7x11x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = mw/g Low Cheek Right WCDMA Band VIII/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = 0.11 db Peak SAR (extrapolated) = mw/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 114 of 299

115 WCDMA Band VIII Body Toward Ground Middle Date/Time: 01/07/2015 Medium: Head 900MHz Medium parameters used: f = 898 MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: WCDMA BAND VIII; Frequency: MHz; Duty Cycle: 1:2.2 Probe: ES3DV3 - SN3252ConvF(6.2, 6.2, 6.2) Middle Toward Ground WCDMA Band VIII/Area Scan (10x16x1): Measurement grid: dx=10mm, dy=10mm Maximum value of SAR (measured) = mw/g Middle Toward Ground WCDMA Band VIII/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = db Peak SAR (extrapolated) = mw/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 115 of 299

116 WCDMA Band VIII Body Phantom Ground Middle Date/Time: 01/07/2015 Medium: Head 900MHz Medium parameters used: f = 898 MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: WCDMA BAND VIII; Frequency: MHz; Duty Cycle: 1:2.2 Probe: ES3DV3 - SN3252ConvF(6.2, 6.2, 6.2) Middle Toward Phantom WCDMA Band VIII/Area Scan (10x16x1): Measurement grid: dx=10mm, dy=10mm Maximum value of SAR (measured) = mw/g Middle Toward Phantom WCDMA Band VIII/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = 0.14 db Peak SAR (extrapolated) = mw/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 116 of 299

117 WCDMA Band VIII Body Left Middle Date/Time: 01/07/2015 Medium: Head 900MHz Medium parameters used: f = 898 MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: WCDMA BAND VIII; Frequency: MHz; Duty Cycle: 1:2.2 Probe: ES3DV3 - SN3252ConvF(6.2, 6.2, 6.2) Middle Left WCDMA Band VIII/Area Scan (5x16x1): Measurement grid: dx=10mm, dy=10mm Maximum value of SAR (measured) = mw/g Middle Left WCDMA Band VIII/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = db Peak SAR (extrapolated) = mw/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 117 of 299

118 WCDMA Band VIII Body Right Middle Date/Time: 01/07/2015 Medium: Head 900MHz Medium parameters used: f = 898 MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: WCDMA BAND VIII; Frequency: MHz; Duty Cycle: 1:2.2 Probe: ES3DV3 - SN3252ConvF(6.2, 6.2, 6.2) Middle Right WCDMA Band VIII/Area Scan (5x16x1): Measurement grid: dx=10mm, dy=10mm Maximum value of SAR (measured) = mw/g Middle Right WCDMA Band VIII/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = 0.06 db Peak SAR (extrapolated) = mw/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 118 of 299

119 WCDMA Band VIII Body Bottom Middle Date/Time: 01/07/2015 Medium: Head 900MHz Medium parameters used: f = 898 MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: WCDMA BAND VIII; Frequency: MHz; Duty Cycle: 1:2.2 Probe: ES3DV3 - SN3252ConvF(6.2, 6.2, 6.2) Middle Bottom WCDMA Band VIII/Area Scan (5x11x1): Measurement grid: dx=10mm, dy=10mm Maximum value of SAR (measured) = mw/g Middle Bottom WCDMA Band VIII/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = 0.08 db Peak SAR (extrapolated) = mw/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 119 of 299

120 WCDMA Band VIII Body Toward Ground High Date/Time: 01/07/2015 Medium: Head 900MHz Medium parameters used: f = 913 MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: WCDMA BAND VIII; Frequency: MHz; Duty Cycle: 1:2.2 Probe: ES3DV3 - SN3252ConvF(6.2, 6.2, 6.2) High Toward Ground WCDMA Band VIII/Area Scan (10x16x1): Measurement grid: dx=10mm, dy=10mm Maximum value of SAR (measured) = mw/g High Toward Ground WCDMA Band VIII/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = 0.09 db Peak SAR (extrapolated) = mw/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 120 of 299

121 WCDMA Band VIII Body Toward Ground Low Date/Time: 01/07/2015 Medium: Head 900MHz Medium parameters used (interpolated): f = MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: WCDMA BAND VIII; Frequency: MHz; Duty Cycle: 1:2.2 Probe: ES3DV3 - SN3252ConvF(6.2, 6.2, 6.2) Low Toward Ground WCDMA Band VIII/Area Scan (10x16x1): Measurement grid: dx=10mm, dy=10mm Maximum value of SAR (measured) = mw/g Low Toward Ground WCDMA Band VIII/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = 0.13 db Peak SAR (extrapolated) = mw/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 121 of 299

122 WCDMA Band VIII Body Toward Ground Low With Headset Date/Time: 01/07/2015 Medium: Head 900MHz Medium parameters used (interpolated): f = MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: WCDMA BAND VIII; Frequency: MHz; Duty Cycle: 1:2.2 Probe: ES3DV3 - SN3252ConvF(6.2, 6.2, 6.2) Low Toward Ground WCDMA Band VIII With Headset/Area Scan (10x16x1): Measurement grid: dx=10mm, dy=10mm Maximum value of SAR (measured) = mw/g Low Toward Ground WCDMA Band VIII With Headset/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = db Peak SAR (extrapolated) = mw/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 122 of 299

123 LTE Band3 3MHz 1RB Left Cheek Middle Date/Time: 01/08/2015 Medium: Head 1800MHz Medium parameters used (interpolated): f = MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: FDD LTE Band3; Frequency: MHz; Duty Cycle: 1:3.74 Probe: ES3DV3 - SN3252ConvF(5.24, 5.24, 5.24); Middle Cheek Left LTE Band3 3MHz 1RB/Area Scan (11x7x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = mw/g Middle Cheek Left LTE Band3 3MHz 1RB/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = db Peak SAR (extrapolated) = mw/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 123 of 299

124 LTE Band3 3MHz 1RB Left Tilt Middle Date/Time: 01/08/2015 Medium: Head 1800MHz Medium parameters used (interpolated): f = MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: FDD LTE Band3; Frequency: MHz; Duty Cycle: 1:3.74 Probe: ES3DV3 - SN3252ConvF(5.24, 5.24, 5.24); Middle Tilt Left LTE Band3 3MHz 1RB/Area Scan (11x7x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = mw/g Middle Tilt Left LTE Band3 3MHz 1RB/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = 0.01 db Peak SAR (extrapolated) = mw/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 124 of 299

125 LTE Band3 3MHz 1RB Right Cheek Middle Date/Time: 01/08/2015 Medium: Head 1800MHz Medium parameters used (interpolated): f = MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: FDD LTE Band3; Frequency: MHz; Duty Cycle: 1:3.74 Probe: ES3DV3 - SN3252ConvF(5.24, 5.24, 5.24); Middle Cheek Right LTE Band3 3MHz 1RB/Area Scan (7x11x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = mw/g Middle Cheek Right LTE Band3 3MHz 1RB/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = 0.10 db Peak SAR (extrapolated) = mw/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 125 of 299

126 LTE Band3 3MHz 1RB Right Tilt Middle Date/Time: 01/08/2015 Medium: Head 1800MHz Medium parameters used (interpolated): f = MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: FDD LTE Band3; Frequency: MHz; Duty Cycle: 1:3.74 Probe: ES3DV3 - SN3252ConvF(5.24, 5.24, 5.24); Middle Tilt Right LTE Band3 3MHz 1RB/Area Scan (7x11x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = mw/g Middle Tilt Right LTE Band3 3MHz 1RB/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = db Peak SAR (extrapolated) = mw/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 126 of 299

127 LTE Band3 3MHz 8RB Left Cheek Middle Date/Time: 01/08/2015 Medium: Head 1800MHz Medium parameters used (interpolated): f = MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: FDD LTE Band3; Frequency: MHz; Duty Cycle: 1:3.74 Probe: ES3DV3 - SN3252ConvF(5.24, 5.24, 5.24); Middle Cheek Left LTE Band3 3MHz 8RB/Area Scan (11x7x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = mw/g Middle Cheek Left LTE Band3 3MHz 8RB/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = 0.12 db Peak SAR (extrapolated) = mw/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 127 of 299

128 LTE Band3 3MHz 8RB Left Tilt Middle Date/Time: 01/08/2015 Medium: Head 1800MHz Medium parameters used (interpolated): f = MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: FDD LTE Band3; Frequency: MHz; Duty Cycle: 1:3.74 Probe: ES3DV3 - SN3252ConvF(5.24, 5.24, 5.24); Middle Tilt Left LTE Band3 3MHz 8RB/Area Scan (11x7x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = mw/g Middle Tilt Left LTE Band3 3MHz 8RB/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = db Peak SAR (extrapolated) = mw/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 128 of 299

129 LTE Band3 3MHz 8RB Right Cheek Middle Date/Time: 01/08/2015 Medium: Head 1800MHz Medium parameters used (interpolated): f = MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: FDD LTE Band3; Frequency: MHz; Duty Cycle: 1:3.74 Probe: ES3DV3 - SN3252ConvF(5.24, 5.24, 5.24); Middle Cheek Right LTE Band3 3MHz 8RB/Area Scan (7x11x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = mw/g Middle Cheek Right LTE Band3 3MHz 8RB/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = db Peak SAR (extrapolated) = mw/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 129 of 299

130 LTE Band3 3MHz 8RB Right Tilt Middle Date/Time: 01/08/2015 Medium: Head 1800MHz Medium parameters used (interpolated): f = MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: FDD LTE Band3; Frequency: MHz; Duty Cycle: 1:3.74 Probe: ES3DV3 - SN3252ConvF(5.24, 5.24, 5.24); Middle Tilt Right LTE Band3 3MHz 8RB/Area Scan (7x11x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = mw/g Middle Tilt Right LTE Band3 3MHz 8RB/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = 0.11 db Peak SAR (extrapolated) = mw/g SAR(1 g) = mw/g; SAR(10 g) = mw/g. Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 130 of 299

131 LTE Band3 3MHz 1RB Left Cheek High Date/Time: 01/08/2015 Medium: Head 1800MHz Medium parameters used (interpolated): f = MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: FDD LTE Band3; Frequency: MHz; Duty Cycle: 1:3.74 Probe: ES3DV3 - SN3252ConvF(5.24, 5.24, 5.24); High Cheek Left LTE Band3 3MHz 1RB/Area Scan (11x7x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = mw/g High Cheek Left LTE Band3 3MHz 1RB/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = 0.13 db Peak SAR (extrapolated) = mw/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 131 of 299

132 LTE Band3 3MHz 1RB Left Cheek Low Date/Time: 01/08/2015 Medium: Head 1800MHz Medium parameters used (interpolated): f = MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: FDD LTE Band3; Frequency: MHz; Duty Cycle: 1:3.74 Probe: ES3DV3 - SN3252ConvF(5.24, 5.24, 5.24); Low Cheek Left LTE Band3 3MHz 1RB/Area Scan (11x7x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = mw/g Low Cheek Left LTE Band3 3MHz 1RB/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = 0.16 db Peak SAR (extrapolated) = mw/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 132 of 299

133 LTE Band3 20MHz 1RB Left Cheek High Date/Time: 01/08/2015 Medium: Head 1800MHz Medium parameters used: f = 1775 MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: FDD LTE Band3; Frequency: 1775 MHz; Duty Cycle: 1:3.74 Probe: ES3DV3 - SN3252ConvF(5.24, 5.24, 5.24); High Cheek Left LTE Band3 20MHz 1RB/Area Scan (11x7x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = mw/g High Cheek Left LTE Band3 20MHz 1RB/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = 0.02 db Peak SAR (extrapolated) = mw/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 133 of 299

134 LTE Band3 15MHz 1RB Left Cheek High Date/Time: 01/08/2015 Medium: Head 1800MHz Medium parameters used (interpolated): f = MHz; σ = mho/m;εr = 39.7; ρ = 1000 kg/m3 Communication System: FDD LTE Band3; Frequency: MHz; Duty Cycle: 1:3.74 Probe: ES3DV3 - SN3252ConvF(5.24, 5.24, 5.24); High Cheek Left LTE Band3 15MHz 1RB/Area Scan (11x7x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = mw/g High Cheek Left LTE Band3 15MHz 1RB/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = 0.11 db Peak SAR (extrapolated) = mw/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 134 of 299

135 LTE Band3 10MHz 1RB Left Cheek High Date/Time: 01/08/2015 Medium: Head 1800MHz Medium parameters used: f = 1780 MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: FDD LTE Band3; Frequency: 1780 MHz; Duty Cycle: 1:3.74 Probe: ES3DV3 - SN3252ConvF(5.24, 5.24, 5.24); High Cheek Left LTE Band3 10MHz 1RB/Area Scan (11x7x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = mw/g High Cheek Left LTE Band3 10MHz 1RB/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = 0.13 db Peak SAR (extrapolated) = mw/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 135 of 299

136 LTE Band3 5MHz 1RB Left Cheek High Date/Time: 01/08/2015 Medium: Head 1800MHz Medium parameters used (interpolated): f = MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: FDD LTE Band3; Frequency: MHz; Duty Cycle: 1:3.74 Probe: ES3DV3 - SN3252ConvF(5.24, 5.24, 5.24); High Cheek Left LTE Band3 5MHz 1RB/Area Scan (11x7x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = mw/g High Cheek Left LTE Band3 5MHz 1RB/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = 0.11 db Peak SAR (extrapolated) = mw/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 136 of 299

137 LTE Band3 1.4MHz 1RB Left Cheek High Date/Time: 01/08/2015 Medium: Head 1800MHz Medium parameters used (interpolated): f = MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: FDD LTE Band3; Frequency: MHz; Duty Cycle: 1:3.74 Probe: ES3DV3 - SN3252ConvF(5.24, 5.24, 5.24); High Cheek Left LTE Band3 1.4MHz 1RB/Area Scan (11x7x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = mw/g High Cheek Left LTE Band3 1.4MHz 1RB/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = 0.18 db Peak SAR (extrapolated) = mw/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 137 of 299

138 LTE Band3 3MHz 1RB Toward Ground Middle Date/Time: 01/08/2015 Medium: Head 1800MHz Medium parameters used (interpolated): f = MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: FDD LTE Band3; Frequency: MHz; Duty Cycle: 1:3.7 Probe: ES3DV3 - SN3252ConvF(5.24, 5.24, 5.24); Middle Toward Ground LTE Band3 3MHz 1RB/Area Scan (10x16x1): Measurement grid: dx=10mm, dy=10mm Maximum value of SAR (measured) = mw/g Middle Toward Ground LTE Band3 3MHz 1RB/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = 0.15 db Peak SAR (extrapolated) = mW/g. SAR(1 g) = mw/g; SAR(10 g) = mw/g. Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 138 of 299

139 LTE Band3 3MHz 1RB Toward Phantom Middle Date/Time: 01/08/2015 Medium: Head 1800MHz Medium parameters used (interpolated): f = MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: FDD LTE Band3; Frequency: MHz; Duty Cycle: 1:3.7 Probe: ES3DV3 - SN3252ConvF(5.24, 5.24, 5.24); Middle Toward Phantom LTE Band3 3MHz 1RB/Area Scan (10x16x1): Measurement grid: dx=10mm, dy=10mm Maximum value of SAR (measured) = mw/g Middle Toward Phantom LTE Band3 3MHz 1RB/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = db Peak SAR (extrapolated) = mW/g. SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 139 of 299

140 LTE Band3 3MHz 1RB Left Middle Date/Time: 01/08/2015 Medium: Head 1800MHz Medium parameters used (interpolated): f = MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: FDD LTE Band3; Frequency: MHz; Duty Cycle: 1:3.7 Probe: ES3DV3 - SN3252ConvF(5.24, 5.24, 5.24); Middle Left LTE Band3 3MHz 1RB/Area Scan (5x16x1): Measurement grid: dx=10mm, dy=10mm Maximum value of SAR (measured) = mw/g Middle Left LTE Band3 3MHz 1RB/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = db Peak SAR (extrapolated) = mW/g. SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 140 of 299

141 LTE Band3 3MHz 1RB Right Middle Date/Time: 01/08/2015 Medium: Head 1800MHz Medium parameters used (interpolated): f = MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: FDD LTE Band3; Frequency: MHz; Duty Cycle: 1:3.7 Probe: ES3DV3 - SN3252ConvF(5.24, 5.24, 5.24); Middle Right LTE Band3 3MHz 1RB/Area Scan (5x16x1): Measurement grid: dx=10mm, dy=10mm Maximum value of SAR (measured) = mw/g Middle Right LTE Band3 3MHz 1RB/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = 0.02 db Peak SAR (extrapolated) = mW/g. SAR(1 g) = mw/g; SAR(10 g) = mw/g. Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 141 of 299

142 LTE Band3 3MHz 1RB Bottom Middle Date/Time: 01/08/2015 Medium: Head 1800MHz Medium parameters used (interpolated): f = MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: FDD LTE Band3; Frequency: MHz; Duty Cycle: 1:3.7 Probe: ES3DV3 - SN3252ConvF(5.24, 5.24, 5.24); Middle Bottom LTE Band3 3MHz 1RB/Area Scan (5x11x1): Measurement grid: dx=10mm, dy=10mm Maximum value of SAR (measured) = mw/g Middle Bottom LTE Band3 3MHz 1RB/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = db Peak SAR (extrapolated) = mw/g. SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 142 of 299

143 LTE Band3 3MHz 8RB Toward Ground Middle Date/Time: 01/08/2015 Medium: Head 1800MHz Medium parameters used (interpolated): f = MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: FDD LTE Band3; Frequency: MHz; Duty Cycle: 1:3.7 Probe: ES3DV3 - SN3252ConvF(5.24, 5.24, 5.24); Middle Toward Ground LTE Band3 3MHz 8RB/Area Scan (10x16x1): Measurement grid: dx=10mm, dy=10mm Maximum value of SAR (measured) = mw/g Middle Toward Ground LTE Band3 3MHz 8RB/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = db Peak SAR (extrapolated) = mw/g. SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 143 of 299

144 LTE Band3 3MHz 8RB Toward Phantom Middle Date/Time: 01/08/2015 Medium: Head 1800MHz Medium parameters used (interpolated): f = MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: FDD LTE Band3; Frequency: MHz; Duty Cycle: 1:3.7 Probe: ES3DV3 - SN3252ConvF(5.24, 5.24, 5.24); Middle Toward Phantom LTE Band3 3MHz 8RB/Area Scan (10x16x1): Measurement grid: dx=10mm, dy=10mm Maximum value of SAR (measured) = mw/g Middle Toward Phantom LTE Band3 3MHz 8RB/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = db Peak SAR (extrapolated) = mW/g. SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 144 of 299

145 LTE Band3 3MHz 8RB Left Middle Date/Time: 01/08/2015 Medium: Head 1800MHz Medium parameters used (interpolated): f = MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: FDD LTE Band3; Frequency: MHz; Duty Cycle: 1:3.7 Probe: ES3DV3 - SN3252ConvF(5.24, 5.24, 5.24); Middle Left LTE Band3 3MHz 8RB/Area Scan (5x16x1): Measurement grid: dx=10mm, dy=10mm Maximum value of SAR (measured) = mw/g Middle Left LTE Band3 3MHz 8RB/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = db Peak SAR (extrapolated) = mW/g. SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = 0.054mW/g East China Institute of Telecommunications Page Number : 145 of 299

146 LTE Band3 3MHz 8RB Right Middle Date/Time: 01/08/2015 Medium: Head 1800MHz Medium parameters used (interpolated): f = MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: FDD LTE Band3; Frequency: MHz; Duty Cycle: 1:3.7 Probe: ES3DV3 - SN3252ConvF(5.24, 5.24, 5.24); Middle Right LTE Band3 3MHz 8RB/Area Scan (5x16x1): Measurement grid: dx=10mm, dy=10mm Maximum value of SAR (measured) = mw/g Middle Right LTE Band3 3MHz 8RB/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = db Peak SAR (extrapolated) = mW/g. SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 146 of 299

147 LTE Band3 3MHz 8RB Bottom Middle Date/Time: 01/08/2015 Medium: Head 1800MHz Medium parameters used (interpolated): f = MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: FDD LTE Band3; Frequency: MHz; Duty Cycle: 1:3.7 Probe: ES3DV3 - SN3252ConvF(5.24, 5.24, 5.24); Middle Bottom LTE Band3 3MHz 8RB/Area Scan (5x11x1): Measurement grid: dx=10mm, dy=10mm Maximum value of SAR (measured) = mw/g Middle Bottom LTE Band3 3MHz 8RB/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = db Peak SAR (extrapolated) = mW/g. SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 147 of 299

148 LTE Band3 3MHz 1RB Toward Ground High Date/Time: 01/08/2015 Medium: Head 1800MHz Medium parameters used (interpolated): f = MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: FDD LTE Band3; Frequency: MHz; Duty Cycle: 1:3.7 Probe: ES3DV3 - SN3252ConvF(5.24, 5.24, 5.24); High Toward Ground LTE Band3 3MHz 1RB/Area Scan (10x16x1): Measurement grid: dx=10mm, dy=10mm Maximum value of SAR (measured) = mw/g High Toward Ground LTE Band3 3MHz 1RB/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = db Peak SAR (extrapolated) = mW/g. SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 148 of 299

149 LTE Band3 3MHz 1RB Toward Ground Low Date/Time: 01/08/2015 Medium: Head 1800MHz Medium parameters used (interpolated): f = MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: FDD LTE Band3; Frequency: MHz; Duty Cycle: 1:3.7 Probe: ES3DV3 - SN3252ConvF(5.24, 5.24, 5.24); Low Toward Ground LTE Band3 3MHz 1RB/Area Scan (10x16x1): Measurement grid: dx=10mm, dy=10mm Maximum value of SAR (measured) = mw/g Low Toward Ground LTE Band3 3MHz 1RB/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = db Peak SAR (extrapolated) = mW/g. SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 149 of 299

150 LTE Band3 20MHz 1RB Toward Ground High Date/Time: 01/08/2015 Medium: Head 1800MHz Medium parameters used: f = 1775 MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: FDD LTE Band3; Frequency: 1775 MHz; Duty Cycle: 1:3.7 Probe: ES3DV3 - SN3252ConvF(5.24, 5.24, 5.24); High Toward Ground LTE Band3 20MHz 1RB/Area Scan (10x16x1): Measurement grid: dx=10mm, dy=10mm Maximum value of SAR (measured) = mw/g High Toward Ground LTE Band3 20MHz 1RB/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = db Peak SAR (extrapolated) = mW/g. SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 150 of 299

151 LTE Band3 15MHz 1RB Toward Ground High Date/Time: 01/08/2015 Medium: Head 1800MHz Medium parameters used (interpolated): f = MHz; σ = mho/m;εr = 39.7; ρ = 1000 kg/m3 Communication System: FDD LTE Band3; Frequency: MHz; Duty Cycle: 1:3.7 Probe: ES3DV3 - SN3252ConvF(5.24, 5.24, 5.24); High Toward Ground LTE Band3 15MHz 1RB/Area Scan (10x16x1): Measurement grid: dx=10mm, dy=10mm Maximum value of SAR (measured) = mw/g High Toward Ground LTE Band3 15MHz 1RB/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = db Peak SAR (extrapolated) = mW/g. SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 151 of 299

152 LTE Band3 10MHz 1RB Toward Ground High Date/Time: 01/08/2015 Medium: Head 1800MHz Medium parameters used: f = 1780 MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: FDD LTE Band3; Frequency: 1780 MHz; Duty Cycle: 1:3.7 Probe: ES3DV3 - SN3252ConvF(5.24, 5.24, 5.24); High Toward Ground LTE Band3 10MHz 1RB/Area Scan (10x16x1): Measurement grid: dx=10mm, dy=10mm Maximum value of SAR (measured) = mw/g High Toward Ground LTE Band3 10MHz 1RB/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = db Peak SAR (extrapolated) = mW/g. SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 152 of 299

153 LTE Band3 5MHz 1RB Toward Ground High Date/Time: 01/08/2015 Medium: Head 1800MHz Medium parameters used (interpolated): f = MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: FDD LTE Band3; Frequency: MHz; Duty Cycle: 1:3.7 Probe: ES3DV3 - SN3252ConvF(5.24, 5.24, 5.24); High Toward Ground LTE Band3 5MHz 1RB/Area Scan (10x16x1): Measurement grid: dx=10mm, dy=10mm Maximum value of SAR (measured) = mw/g High Toward Ground LTE Band3 5MHz 1RB/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = 0.08 db Peak SAR (extrapolated) = mW/g. SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 153 of 299

154 LTE Band3 1.4MHz 1RB Toward Ground High Date/Time: 01/08/2015 Medium: Head 1800MHz Medium parameters used (interpolated): f = MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: FDD LTE Band3; Frequency: MHz; Duty Cycle: 1:3.7 Probe: ES3DV3 - SN3252ConvF(5.24, 5.24, 5.24); High Toward Ground LTE Band3 1.4MHz 1RB/Area Scan (10x16x1): Measurement grid: dx=10mm, dy=10mm Maximum value of SAR (measured) = mw/g High Toward Ground LTE Band3 1.4MHz 1RB/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = 0.12 db Peak SAR (extrapolated) = mW/g. SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 154 of 299

155 LTE Band7 20MHz 1RB Left Cheek High Date/Time: 01/14/2015 Medium: Head 2550MHz Medium parameters used: f = 2560 MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: FDD LTE band7; Frequency: 2560 MHz; Duty Cycle: 1:3.74 Probe: ES3DV3 - SN3252ConvF(4.28, 4.28, 4.28); High Cheek Left LTE Band7 20MHz 1RB/Area Scan (11x7x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = mw/g High Cheek Left LTE Band7 20MHz 1RB/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = db Peak SAR (extrapolated) = mW/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 155 of 299

156 LTE Band7 20MHz 1RB Left Tilt High Date/Time: 01/14/2015 Medium: Head 2550MHz Medium parameters used: f = 2560 MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: FDD LTE band7; Frequency: 2560 MHz; Duty Cycle: 1:3.74 Probe: ES3DV3 - SN3252ConvF(4.28, 4.28, 4.28); High Tilt Left LTE Band7 20MHz 1RB/Area Scan (11x7x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = mw/g High Tilt Left LTE Band7 20MHz 1RB/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = db Peak SAR (extrapolated) = mW/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 156 of 299

157 LTE Band7 20MHz 1RB Right Cheek High Date/Time: 01/14/2015 Medium: Head 2550MHz Medium parameters used: f = 2560 MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: FDD LTE band7; Frequency: 2560 MHz; Duty Cycle: 1:3.74 Probe: ES3DV3 - SN3252ConvF(4.28, 4.28, 4.28); High Cheek Right LTE Band7 20MHz 1RB/Area Scan (7x11x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = mw/g High Cheek Right LTE Band7 20MHz 1RB/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 0 V/m; Power Drift = 0.08 db Peak SAR (extrapolated) = mW/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 157 of 299

158 LTE Band7 20MHz 1RB Right Tilt High Date/Time: 01/14/2015 Medium: Head 2550MHz Medium parameters used: f = 2560 MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: FDD LTE band7; Frequency: 2560 MHz; Duty Cycle: 1:3.74 Probe: ES3DV3 - SN3252ConvF(4.28, 4.28, 4.28); High Tilt Right LTE Band7 20MHz 1RB/Area Scan (7x11x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = mw/g High Tilt Right LTE Band7 20MHz 1RB/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = 0.07 db Peak SAR (extrapolated) = mW/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 158 of 299

159 LTE Band7 20MHz 50RB Left Cheek High Date/Time: 01/14/2015 Medium: Head 2550MHz Medium parameters used: f = 2560 MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: FDD LTE band7; Frequency: 2560 MHz; Duty Cycle: 1:3.74 Probe: ES3DV3 - SN3252ConvF(4.28, 4.28, 4.28); High Cheek Left LTE Band7 20MHz 50RB/Area Scan (11x7x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = mw/g High Cheek Left LTE Band7 20MHz 50RB/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 0 V/m; Power Drift = 0.01 db Peak SAR (extrapolated) = mW/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 159 of 299

160 LTE Band7 20MHz 50RB Left Tilt High Date/Time: 01/14/2015 Medium: Head 2550MHz Medium parameters used: f = 2560 MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: FDD LTE band7; Frequency: 2560 MHz; Duty Cycle: 1:3.74 Probe: ES3DV3 - SN3252ConvF(4.28, 4.28, 4.28); High Tilt Left LTE Band7 20MHz 50RB/Area Scan (11x7x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = mw/g High Tilt Left LTE Band7 20MHz 50RB/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = 0.11 db Peak SAR (extrapolated) = mW/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 160 of 299

161 LTE Band7 20MHz 50RB Right Cheek High Date/Time: 01/14/2015 Medium: Head 2550MHz Medium parameters used: f = 2560 MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: FDD LTE band7; Frequency: 2560 MHz; Duty Cycle: 1:3.74 Probe: ES3DV3 - SN3252ConvF(4.28, 4.28, 4.28); High Cheek Right LTE Band7 20MHz 50RB/Area Scan (7x11x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = mw/g High Cheek Right LTE Band7 20MHz 50RB/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = db Peak SAR (extrapolated) = mW/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 161 of 299

162 LTE Band7 20MHz 50RB Right Tilt High Date/Time: 01/14/2015 Medium: Head 2550MHz Medium parameters used: f = 2560 MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: FDD LTE band7; Frequency: 2560 MHz; Duty Cycle: 1:3.74 Probe: ES3DV3 - SN3252ConvF(4.28, 4.28, 4.28); High Tilt Right LTE Band7 20MHz 50RB/Area Scan (7x11x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = mw/g High Tilt Right LTE Band7 20MHz 50RB/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = 0.05 db Peak SAR (extrapolated) = mW/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = 0.024mW/g East China Institute of Telecommunications Page Number : 162 of 299

163 LTE Band7 20MHz 1RB Left Cheek Middle Date/Time: 01/14/2015 Medium: Head 2550MHz Medium parameters used: f = 2535 MHz; σ = mho/m;εr = 38.96; ρ = 1000 kg/m3 Communication System: FDD LTE band7; Frequency: 2535 MHz; Duty Cycle: 1:3.74 Probe: ES3DV3 - SN3252ConvF(4.28, 4.28, 4.28); Middle Cheek Left LTE Band3 20MHz 1RB/Area Scan (11x7x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = mw/g Middle Cheek Left LTE Band3 20MHz 1RB/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = -0.05dB Peak SAR (extrapolated) = mW/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 163 of 299

164 LTE Band7 20MHz 1RB Left Cheek Low Date/Time: 01/14/2015 Medium: Head 2550MHz Medium parameters used: f = 2510 MHz; σ = mho/m;εr = 38.72; ρ = 1000 kg/m3 Communication System: FDD LTE band7; Frequency: 2510 MHz; Duty Cycle: 1:3.74 Probe: ES3DV3 - SN3252ConvF(4.28, 4.28, 4.28); Low Cheek Left LTE Band3 20MHz 1RB/Area Scan (11x7x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = mw/g Low Cheek Left LTE Band3 20MHz 1RB/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 0 V/m; Power Drift = 0.08 db Peak SAR (extrapolated) = mW/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 164 of 299

165 LTE Band7 15MHz 1RB Left Cheek High Date/Time: 01/14/2015 Medium: Head 2550MHz Medium parameters used: f = MHz; σ = mho/m;εr = 38.14; ρ = 1000 kg/m3 Communication System: FDD LTE band7; Frequency: MHz; Duty Cycle: 1:3.74 Probe: ES3DV3 - SN3252ConvF(4.28, 4.28, 4.28); High Cheek Left LTE Band7 15MHz 1RB/Area Scan (11x7x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = mw/g High Cheek Left LTE Band7 15MHz 1RB/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 0 V/m; Power Drift = 0.12 db Peak SAR (extrapolated) = mW/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 165 of 299

166 LTE Band7 10MHz 1RB Left Cheek High Date/Time: 01/14/2015 Medium: Head 2550MHz Medium parameters used: f = 2565 MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: FDD LTE band7; Frequency: 2565 MHz; Duty Cycle: 1:3.74 Probe: ES3DV3 - SN3252ConvF(4.28, 4.28, 4.28); Low Cheek Left LTE Band3 10MHz 1RB/Area Scan (11x7x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = mw/g Low Cheek Left LTE Band3 10MHz 1RB/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = 0.13 db Peak SAR (extrapolated) = mW/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 166 of 299

167 LTE Band7 5MHz 1RB Left Cheek High Date/Time: 01/14/2015 Medium: Head 2550MHz Medium parameters used: f = MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: FDD LTE band7; Frequency: MHz; Duty Cycle: 1:3.74 Probe: ES3DV3 - SN3252ConvF(4.28, 4.28, 4.28); High Cheek Left LTE Band7 5MHz 1RB/Area Scan (11x7x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = mw/g High Cheek Left LTE Band7 5MHz 1RB/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 0 V/m; Power Drift = 0.11 db Peak SAR (extrapolated) = mW/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 167 of 299

168 LTE Band7 20MHz 1RB Toward Ground High Date/Time: 01/14/2015 Medium: Head 2550MHz Medium parameters used: f = 2560 MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: FDD LTE band7; Frequency: 2560 MHz; Duty Cycle: 1:3.7 Probe: ES3DV3 - SN3252ConvF(4.28, 4.28, 4.28); High Toward Ground LTE Band7 20MHz 1RB/Area Scan (10x16x1): Measurement grid: dx=10mm, dy=10mm Maximum value of SAR (measured) = mw/g High Toward Ground LTE Band7 20MHz 1RB/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = 0.11 db Peak SAR (extrapolated) = mw/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 168 of 299

169 LTE Band7 20MHz 1RB Toward Phantom High Date/Time: 01/14/2015 Medium: Head 2550MHz Medium parameters used: f = 2560 MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: FDD LTE band7; Frequency: 2560 MHz; Duty Cycle: 1:3.7 Probe: ES3DV3 - SN3252ConvF(4.28, 4.28, 4.28); High Toward Phantom LTE Band7 20MHz 1RB/Area Scan (10x16x1): Measurement grid: dx=10mm, dy=10mm Maximum value of SAR (measured) = mw/g High Toward Phantom LTE Band7 20MHz 1RB/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = 0.19 db Peak SAR (extrapolated) = mw/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 169 of 299

170 LTE Band7 20MHz 1RB Left High Date/Time: 01/14/2015 Medium: Head 2550MHz Medium parameters used: f = 2472 MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: FDD LTE band7; Frequency: 2560 MHz; Duty Cycle: 1:3.7 Probe: ES3DV3 - SN3252ConvF(4.28, 4.28, 4.28); High Left LTE Band7 20MHz 1RB/Area Scan (5x16x1): Measurement grid: dx=10mm, dy=10mm Maximum value of SAR (measured) = mw/g High Left LTE Band7 20MHz 1RB/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = 0.03 db Peak SAR (extrapolated) = mw/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 170 of 299

171 LTE Band7 20MHz 1RB Right High Date/Time: 01/14/2015 Medium: Head 2550MHz Medium parameters used: f = 2560 MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: FDD LTE band7; Frequency: 2560 MHz; Duty Cycle: 1:3.7 Probe: ES3DV3 - SN3252ConvF(4.28, 4.28, 4.28); High Right LTE Band7 20MHz 1RB/Area Scan (5x16x1): Measurement grid: dx=10mm, dy=10mm Maximum value of SAR (measured) = mw/g High Right LTE Band7 20MHz 1RB/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 0 V/m; Power Drift = 0.12 db Peak SAR (extrapolated) = mw/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 171 of 299

172 LTE Band7 20MHz 1RB Bottom High Date/Time: 01/14/2015 Medium: Head 2550MHz Medium parameters used: f = 2560 MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: FDD LTE band7; Frequency: 2560 MHz; Duty Cycle: 1:3.7 Probe: ES3DV3 - SN3252ConvF(4.28, 4.28, 4.28); High Bottom LTE Band7 20MHz 1RB/Area Scan (5x11x1): Measurement grid: dx=10mm, dy=10mm Maximum value of SAR (measured) = mw/g High Bottom LTE Band7 20MHz 1RB/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = 0.13 db Peak SAR (extrapolated) = mw/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 172 of 299

173 LTE Band7 20MHz 50RB Toward Ground High Date/Time: 01/14/2015 Medium: Head 2550MHz Medium parameters used: f = 2560 MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: FDD LTE band7; Frequency: 2560 MHz; Duty Cycle: 1:3.7 Probe: ES3DV3 - SN3252ConvF(4.28, 4.28, 4.28); High Toward Ground LTE Band7 20MHz 50RB/Area Scan (10x16x1): Measurement grid: dx=10mm, dy=10mm Maximum value of SAR (measured) = mw/g High Toward Ground LTE Band7 20MHz 50RB/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift =0.15 db Peak SAR (extrapolated) = mw/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 173 of 299

174 LTE Band7 20MHz 50RB Toward Phantom High Date/Time: 01/14/2015 Medium: Head 2550MHz Medium parameters used: f = 2560 MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: FDD LTE band7; Frequency: 2560 MHz; Duty Cycle: 1:3.7 Probe: ES3DV3 - SN3252ConvF(4.28, 4.28, 4.28); High Toward Phantom LTE Band7 20MHz 50RB/Area Scan (10x16x1): Measurement grid: dx=10mm, dy=10mm Maximum value of SAR (measured) = mw/g High Toward Phantom LTE Band7 20MHz 50RB/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = 0.17 db Peak SAR (extrapolated) = mw/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 174 of 299

175 LTE Band7 20MHz 50RB Left High Date/Time: 01/14/2015 Medium: Head 2550MHz Medium parameters used: f = 2472 MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: FDD LTE band7; Frequency: 2560 MHz; Duty Cycle: 1:3.7 Probe: ES3DV3 - SN3252ConvF(4.28, 4.28, 4.28); High Left LTE Band7 20MHz 50RB/Area Scan (5x16x1): Measurement grid: dx=10mm, dy=10mm Maximum value of SAR (measured) = mw/g High Left LTE Band7 20MHz 50RB/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = 0.02 db Peak SAR (extrapolated) = mw/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 175 of 299

176 LTE Band7 20MHz 50RB Right High Date/Time: 01/14/2015 Medium: Head 2550MHz Medium parameters used: f = 2560 MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: FDD LTE band7; Frequency: 2560 MHz; Duty Cycle: 1:3.7 Probe: ES3DV3 - SN3252ConvF(4.28, 4.28, 4.28); High Right LTE Band7 20MHz 50RB/Area Scan (5x16x1): Measurement grid: dx=10mm, dy=10mm Maximum value of SAR (measured) = mw/g High Right LTE Band7 20MHz 50RB/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 0 V/m; Power Drift = 0.12 db Peak SAR (extrapolated) = mw/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 176 of 299

177 LTE Band7 20MHz 50RB Bottom High Date/Time: 01/14/2015 Medium: Head 2550MHz Medium parameters used: f = 2560 MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: FDD LTE band7; Frequency: 2560 MHz; Duty Cycle: 1:3.7 Probe: ES3DV3 - SN3252ConvF(4.28, 4.28, 4.28); High Bottom LTE Band7 20MHz 50RB/Area Scan (5x11x1): Measurement grid: dx=10mm, dy=10mm Maximum value of SAR (measured) = mw/g High Bottom LTE Band7 20MHz 50RB/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = 0.18 db Peak SAR (extrapolated) = mw/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 177 of 299

178 LTE Band7 20MHz 1RB Toward Ground Middle Date/Time: 01/14/2015 Medium: Head 2550MHz Medium parameters used: f = 2535 MHz; σ = mho/m;εr = 38.96; ρ = 1000 kg/m3 Communication System: FDD LTE band7; Frequency: 2535 MHz; Duty Cycle: 1:3.7 Probe: ES3DV3 - SN3252ConvF(4.28, 4.28, 4.28); Middle Toward Ground LTE Band7 20MHz 1RB/Area Scan (10x16x1): Measurement grid: dx=10mm, dy=10mm Maximum value of SAR (measured) = mw/g Middle Toward Ground LTE Band7 20MHz 1RB/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = 0.10 db Peak SAR (extrapolated) = mw/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 178 of 299

179 LTE Band7 20MHz 1RB Toward Ground Low Date/Time: 01/14/2015 Medium: Head 2550MHz Medium parameters used: f = 2510 MHz; σ = mho/m;εr = 38.72; ρ = 1000 kg/m3 Communication System: FDD LTE band7; Frequency: 2510 MHz; Duty Cycle: 1:3.7 Probe: ES3DV3 - SN3252ConvF(4.28, 4.28, 4.28); Low Toward Ground LTE Band7 20MHz 1RB/Area Scan (10x16x1): Measurement grid: dx=10mm, dy=10mm Maximum value of SAR (measured) = mw/g Low Toward Ground LTE Band7 20MHz 1RB/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = 0.09 db Peak SAR (extrapolated) = mw/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 179 of 299

180 LTE Band7 15MHz 1RB Toward Ground High Date/Time: 01/14/2015 Medium: Head 2550MHz Medium parameters used: f = MHz; σ = mho/m;εr = 38.14; ρ = 1000 kg/m3 Communication System: FDD LTE band7; Frequency: MHz; Duty Cycle: 1:3.7 Probe: ES3DV3 - SN3252ConvF(4.28, 4.28, 4.28); High Toward Ground LTE Band7 15MHz 1RB/Area Scan (10x16x1): Measurement grid: dx=10mm, dy=10mm Maximum value of SAR (measured) = mw/g High Toward Ground LTE Band7 15MHz 1RB/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = 0.12 db Peak SAR (extrapolated) = mw/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 180 of 299

181 LTE Band7 10MHz 1RB Toward Ground High Date/Time: 01/14/2015 Medium: Head 2550MHz Medium parameters used: f = 2565 MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: FDD LTE band7; Frequency: 2565 MHz; Duty Cycle: 1:3.7 Probe: ES3DV3 - SN3252ConvF(4.28, 4.28, 4.28); High Toward Ground LTE Band7 10MHz 1RB/Area Scan (10x16x1): Measurement grid: dx=10mm, dy=10mm Maximum value of SAR (measured) = mw/g High Toward Ground LTE Band7 10MHz 1RB/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = 0.12 db Peak SAR (extrapolated) = mw/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 181 of 299

182 LTE Band7 5MHz 1RB Toward Ground High Date/Time: 01/14/2015 Medium: Head 2550MHz Medium parameters used: f = MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: FDD LTE band7; Frequency: MHz; Duty Cycle: 1:3.7 Probe: ES3DV3 - SN3252ConvF(4.28, 4.28, 4.28); High Toward Ground LTE Band7 5MHz 1RB/Area Scan (10x16x1): Measurement grid: dx=10mm, dy=10mm Maximum value of SAR (measured) = mw/g High Toward Ground LTE Band7 5MHz 1RB/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = db Peak SAR (extrapolated) = mw/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 182 of 299

183 LTE Band8 5MHz 1RB Left Cheek Middle Date/Time: 01/07/2015 Medium: Head 900MHz Medium parameters used (interpolated): f = MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: TDD LTE Band 8; Frequency: MHz; Duty Cycle: 1:3.7 Probe: ES3DV3 - SN3252ConvF(6.2, 6.2, 6.2) Middle Cheek Left LTE Band8 5MHz 1RB/Area Scan (11x7x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = mw/g Middle Cheek Left LTE Band8 5MHz 1RB/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = -0.12dB Peak SAR (extrapolated) = mW/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 183 of 299

184 LTE Band8 5MHz 1RB Left Tilt Middle Date/Time: 01/07/2015 Medium: Head 900MHz Medium parameters used (interpolated): f = MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: TDD LTE Band 8; Frequency: MHz; Duty Cycle: 1:3.7 Probe: ES3DV3 - SN3252ConvF(6.2, 6.2, 6.2) Middle Tilt Left LTE Band8 5MHz 1RB/Area Scan (11x7x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = mw/g Middle Tilt Left LTE Band8 5MHz 1RB/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = 0.09 db Peak SAR (extrapolated) = mW/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 184 of 299

185 LTE Band8 5MHz 1RB Right Cheek Middle Date/Time: 01/07/2015 Medium: Head 900MHz Medium parameters used (interpolated): f = MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: TDD LTE Band 8; Frequency: MHz; Duty Cycle: 1:3.7 Probe: ES3DV3 - SN3252ConvF(6.2, 6.2, 6.2) Middle Cheek Right LTE Band8 5MHz 1RB/Area Scan (7x11x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = mw/g Middle Cheek Right LTE Band8 5MHz 1RB/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = db Peak SAR (extrapolated) = mW/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 185 of 299

186 LTE Band8 5MHz 1RB Right Tilt Middle Date/Time: 01/07/2015 Medium: Head 900MHz Medium parameters used (interpolated): f = MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: TDD LTE Band 8; Frequency: MHz; Duty Cycle: 1:3.7 Probe: ES3DV3 - SN3252ConvF(6.2, 6.2, 6.2) Middle Tilt Right LTE Band8 5MHz 1RB/Area Scan (7x11x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = mw/g Middle Tilt Right LTE Band8 5MHz 1RB/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = db Peak SAR (extrapolated) = mW/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 186 of 299

187 LTE Band8 5MHz 12RB Left Cheek Middle Date/Time: 01/07/2015 Medium: Head 900MHz Medium parameters used (interpolated): f = MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: TDD LTE Band 8; Frequency: MHz; Duty Cycle: 1:3.7 Probe: ES3DV3 - SN3252ConvF(6.2, 6.2, 6.2) Middle Cheek Left LTE Band8 5MHz 12RB/Area Scan (11x7x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = mw/g Middle Cheek Left LTE Band8 5MHz 12RB/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = 0.11 db Peak SAR (extrapolated) = mW/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 187 of 299

188 LTE Band8 5MHz 12RB Left Tilt Middle Date/Time: 01/07/2015 Medium: Head 900MHz Medium parameters used (interpolated): f = MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: TDD LTE Band 8; Frequency: MHz; Duty Cycle: 1:3.7 Probe: ES3DV3 - SN3252ConvF(6.2, 6.2, 6.2) Middle Tilt Left LTE Band8 5MHz 12RB/Area Scan (11x7x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = mw/g Middle Tilt Left LTE Band8 5MHz 12RB/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = db Peak SAR (extrapolated) = mW/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 188 of 299

189 LTE Band8 5MHz 12RB Right Cheek Middle Date/Time: 01/07/2015 Medium: Head 900MHz Medium parameters used (interpolated): f = MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: TDD LTE Band 8; Frequency: MHz; Duty Cycle: 1:3.7 Probe: ES3DV3 - SN3252ConvF(6.2, 6.2, 6.2) Middle Cheek Right LTE Band8 5MHz 12RB/Area Scan (7x11x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = mw/g Middle Cheek Right LTE Band8 5MHz 12RB/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = db Peak SAR (extrapolated) = mW/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 189 of 299

190 LTE Band8 5MHz 12RB Right Tilt Middle Date/Time: 01/07/2015 Medium: Head 900MHz Medium parameters used (interpolated): f = MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: TDD LTE Band 8; Frequency: MHz; Duty Cycle: 1:3.7 Probe: ES3DV3 - SN3252ConvF(6.2, 6.2, 6.2) Middle Tilt Right LTE Band8 5MHz 12RB/Area Scan (7x11x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = mw/g Middle Tilt Right LTE Band8 5MHz 12RB/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = 0.18 db Peak SAR (extrapolated) = mW/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 190 of 299

191 LTE Band8 5MHz 1RB Right Cheek High Date/Time: 01/07/2015 Medium: Head 900MHz Medium parameters used: f = 915 MHz; σ = mho/m;εr = 41.21; ρ = 1000 kg/m3 Communication System: TDD LTE Band 8; Frequency: MHz; Duty Cycle: 1:3.7 Probe: ES3DV3 - SN3252ConvF(6.2, 6.2, 6.2) High Cheek Right LTE Band8 5MHz 1RB/Area Scan (7x11x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = mw/g High Cheek Right LTE Band8 5MHz 1RB/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = db Peak SAR (extrapolated) = mW/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 191 of 299

192 LTE Band8 5MHz 1RB Right Cheek Low Date/Time: 01/07/2015 Medium: Head 900MHz Medium parameters used: f = 880 MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: TDD LTE Band 8; Frequency: 880 MHz; Duty Cycle: 1:3.7 Probe: ES3DV3 - SN3252ConvF(6.2, 6.2, 6.2) Low Cheek Right LTE Band8 5MHz 1RB/Area Scan (7x11x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = mw/g Low Cheek Right LTE Band8 5MHz 1RB/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = db Peak SAR (extrapolated) = mW/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 192 of 299

193 LTE Band8 10MHz 1RB Right Cheek Low Date/Time: 01/07/2015 Medium: Head 900MHz Medium parameters used: f = 885 MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: TDD LTE Band 8; Frequency: 885 MHz; Duty Cycle: 1:3.7 Probe: ES3DV3 - SN3252ConvF(6.2, 6.2, 6.2) Low Cheek Right LTE Band8 10MHz 1RB/Area Scan (7x11x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = mw/g Low Cheek Right LTE Band8 10MHz 1RB/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = db Peak SAR (extrapolated) = mW/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 193 of 299

194 LTE Band8 3MHz 1RB Right Cheek Low Date/Time: 01/07/2015 Medium: Head 900MHz Medium parameters used: f = 880 MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: TDD LTE Band 8; Frequency: 880 MHz; Duty Cycle: 1:3.7 Probe: ES3DV3 - SN3252ConvF(6.2, 6.2, 6.2) Low Cheek Right LTE Band8 3MHz 1RB/Area Scan (7x11x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = mw/g Low Cheek Right LTE Band8 3MHz 1RB/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = db Peak SAR (extrapolated) = mW/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 194 of 299

195 LTE Band8 1.4MHz 1RB Right Cheek Low Date/Time: 01/07/2015 Medium: Head 900MHz Medium parameters used: f = 881 MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: TDD LTE Band 8; Frequency: MHz; Duty Cycle: 1:3.7 Probe: ES3DV3 - SN3252ConvF(6.2, 6.2, 6.2) Low Cheek Right LTE Band8 1.4MHz 1RB/Area Scan (7x11x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = mw/g Low Cheek Right LTE Band8 1.4MHz 1RB/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = db Peak SAR (extrapolated) = mW/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 195 of 299

196 LTE Band8 5MHz 1RB Toward Ground Middle Date/Time: 01/07/2015 Medium: Head 900MHz Medium parameters used (interpolated): f = MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: TDD LTE Band 8; Frequency: MHz; Duty Cycle: 1:3.7 Probe: ES3DV3 - SN3252ConvF(6.2, 6.2, 6.2) Middle Toward Ground LTE Band8 5MHz 1RB/Area Scan (10x16x1): Measurement grid: dx=10mm, dy=10mm Maximum value of SAR (measured) = mw/g Middle Toward Ground LTE Band8 5MHz 1RB/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = db Peak SAR (extrapolated) = mw/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 196 of 299

197 LTE Band8 5MHz 1RB Toward Phantom Middle Date/Time: 01/07/2015 Medium: Head 900MHz Medium parameters used (interpolated): f = MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: TDD LTE Band 8; Frequency: MHz; Duty Cycle: 1:3.7 Probe: ES3DV3 - SN3252ConvF(6.2, 6.2, 6.2) Middle Toward Phantom LTE Band8 5MHz 1RB/Area Scan (10x16x1): Measurement grid: dx=10mm, dy=10mm Maximum value of SAR (measured) = mw/g Middle Toward Phantom LTE Band8 5MHz 1RB/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = db Peak SAR (extrapolated) = mw/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 197 of 299

198 LTE Band8 5MHz 1RB Left Middle Date/Time: 01/07/2015 Medium: Head 900MHz Medium parameters used (interpolated): f = MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: TDD LTE Band 8; Frequency: MHz; Duty Cycle: 1:3.7 Probe: ES3DV3 - SN3252ConvF(6.2, 6.2, 6.2) Middle Left LTE Band8 5MHz 1RB/Area Scan (5x16x1): Measurement grid: dx=10mm, dy=10mm Maximum value of SAR (measured) = mw/g Middle Left LTE Band8 5MHz 1RB/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = db Peak SAR (extrapolated) = mw/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 198 of 299

199 LTE Band8 5MHz 1RB Right Middle Date/Time: 01/07/2015 Medium: Head 900MHz Medium parameters used (interpolated): f = MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: TDD LTE Band 8; Frequency: MHz; Duty Cycle: 1:3.7 Probe: ES3DV3 - SN3252ConvF(6.2, 6.2, 6.2) Middle Right LTE Band8 5MHz 1RB/Area Scan (5x16x1): Measurement grid: dx=10mm, dy=10mm Maximum value of SAR (measured) = mw/g Middle Right LTE Band8 5MHz 1RB/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = db Peak SAR (extrapolated) = mw/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 199 of 299

200 LTE Band8 5MHz 1RB Bottom Middle Date/Time: 01/07/2015 Medium: Head 900MHz Medium parameters used (interpolated): f = MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: TDD LTE Band 8; Frequency: MHz; Duty Cycle: 1:3.7 Probe: ES3DV3 - SN3252ConvF(6.2, 6.2, 6.2) Middle Bottom LTE Band8 5MHz 1RB/Area Scan (5x11x1): Measurement grid: dx=10mm, dy=10mm. Maximum value of SAR (measured) = mw/g Middle Bottom LTE Band8 5MHz 1RB/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = db Peak SAR (extrapolated) = mw/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 200 of 299

201 LTE Band8 5MHz 12RB Toward Ground Middle Date/Time: 01/07/2015 Medium: Head 900MHz Medium parameters used (interpolated): f = MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: TDD LTE Band 8; Frequency: MHz; Duty Cycle: 1:3.7 Probe: ES3DV3 - SN3252ConvF(6.2, 6.2, 6.2) Middle Toward Ground LTE Band8 5MHz 12RB/Area Scan (10x16x1): Measurement grid: dx=10mm, dy=10mm Maximum value of SAR (measured) = mw/g Middle Toward Ground LTE Band8 5MHz 12RB/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = db Peak SAR (extrapolated) = mw/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 201 of 299

202 LTE Band8 5MHz 12RB Toward Phantom Middle Date/Time: 01/07/2015 Medium: Head 900MHz Medium parameters used (interpolated): f = MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: TDD LTE Band 8; Frequency: MHz; Duty Cycle: 1:3.7 Probe: ES3DV3 - SN3252ConvF(6.2, 6.2, 6.2) Middle Toward Phantom LTE Band8 5MHz 12RB/Area Scan (10x16x1): Measurement grid: dx=10mm, dy=10mm Maximum value of SAR (measured) = mw/g Middle Toward Phantom LTE Band8 5MHz 12RB/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = 0.09 db Peak SAR (extrapolated) = mw/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 202 of 299

203 LTE Band8 5MHz 12RB Left Middle Date/Time: 01/07/2015 Medium: Head 900MHz Medium parameters used (interpolated): f = MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: TDD LTE Band 8; Frequency: MHz; Duty Cycle: 1:3.7 Probe: ES3DV3 - SN3252ConvF(6.2, 6.2, 6.2) Middle Left LTE Band8 5MHz 12RB/Area Scan (5x16x1): Measurement grid: dx=10mm, dy=10mm Maximum value of SAR (measured) = mw/g Middle Left LTE Band8 5MHz 12RB/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = db Peak SAR (extrapolated) = mw/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 203 of 299

204 LTE Band8 5MHz 12RB Right Middle Date/Time: 01/07/2015 Medium: Head 900MHz Medium parameters used (interpolated): f = MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: TDD LTE Band 8; Frequency: MHz; Duty Cycle: 1:3.7 Probe: ES3DV3 - SN3252ConvF(6.2, 6.2, 6.2) Middle Right LTE Band8 5MHz 12RB/Area Scan (5x16x1): Measurement grid: dx=10mm, dy=10mm. Maximum value of SAR (measured) = mw/g Middle Right LTE Band8 5MHz 12RB/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = 0.07 db Peak SAR (extrapolated) = mw/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 204 of 299

205 LTE Band8 5MHz 12RB Bottom Middle Date/Time: 01/07/2015 Medium: Head 900MHz Medium parameters used (interpolated): f = MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: TDD LTE Band 8; Frequency: MHz; Duty Cycle: 1:3.7 Probe: ES3DV3 - SN3252ConvF(6.2, 6.2, 6.2) Middle Bottom LTE Band8 5MHz 12RB/Area Scan (5x11x1): Measurement grid: dx=10mm, dy=10mm Maximum value of SAR (measured) = mw/g Middle Bottom LTE Band8 5MHz 12RB/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = db Peak SAR (extrapolated) = mw/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 205 of 299

206 LTE Band8 5MHz 1RB Toward Ground High Date/Time: 01/07/2015 Medium: Head 900MHz Medium parameters used: f = 915 MHz; σ = mho/m;εr = 41.21; ρ = 1000 kg/m3 Communication System: TDD LTE Band 8; Frequency: MHz; Duty Cycle: 1:3.7 Probe: ES3DV3 - SN3252ConvF(6.2, 6.2, 6.2) High Toward Ground LTE Band8 5MHz 1RB/Area Scan (10x16x1): Measurement grid: dx=10mm, dy=10mm Maximum value of SAR (measured) = mw/g High Toward Ground LTE Band8 5MHz 1RB/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = db Peak SAR (extrapolated) = mw/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 206 of 299

207 LTE Band8 5MHz 1RB Toward Ground Low Date/Time: 01/07/2015 Medium: Head 900MHz Medium parameters used: f = 880 MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: TDD LTE Band 8; Frequency: 880 MHz; Duty Cycle: 1:3.7 Probe: ES3DV3 - SN3252ConvF(6.2, 6.2, 6.2) Low Toward Ground LTE Band8 5MHz 1RB/Area Scan (10x16x1): Measurement grid: dx=10mm, dy=10mm Maximum value of SAR (measured) = mw/g Low Toward Ground LTE Band8 5MHz 1RB/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = 0.07 db Peak SAR (extrapolated) = mw/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 207 of 299

208 LTE Band8 10MHz 1RB Toward Ground Middle Date/Time: 01/07/2015 Medium: Head 900MHz Medium parameters used (interpolated): f = MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: TDD LTE Band 8; Frequency: MHz; Duty Cycle: 1:3.7 Probe: ES3DV3 - SN3252ConvF(6.2, 6.2, 6.2) Middle Toward Ground LTE Band8 10MHz 1RB/Area Scan (10x16x1): Measurement grid: dx=10mm, dy=10mm Maximum value of SAR (measured) = mw/g Middle Toward Ground LTE Band8 10MHz 1RB/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = db Peak SAR (extrapolated) = mw/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 208 of 299

209 LTE Band8 3MHz 1RB Toward Ground Middle Date/Time: 01/07/2015 Medium: Head 900MHz Medium parameters used (interpolated): f = MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: TDD LTE Band 8; Frequency: MHz; Duty Cycle: 1:3.7 Probe: ES3DV3 - SN3252ConvF(6.2, 6.2, 6.2) Middle Toward Ground LTE Band8 3MHz 1RB/Area Scan (10x16x1): Measurement grid: dx=10mm, dy=10mm Maximum value of SAR (measured) = mw/g Middle Toward Ground LTE Band8 3MHz 1RB/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = db Peak SAR (extrapolated) = mW/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 209 of 299

210 LTE Band8 1.4MHz 1RB Toward Ground Middle Date/Time: 01/07/2015 Medium: Head 900MHz Medium parameters used (interpolated): f = MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: TDD LTE Band 8; Frequency: MHz; Duty Cycle: 1:3.7 Probe: ES3DV3 - SN3252ConvF(6.2, 6.2, 6.2) Middle Toward Ground LTE Band8 1.4MHz 1RB/Area Scan (10x16x1): Measurement grid: dx=10mm, dy=10mm Maximum value of SAR (measured) = mw/g Middle Toward Ground LTE Band8 1.4MHz 1RB/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = db Peak SAR (extrapolated) = mW/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 210 of 299

211 LTE Band20 5MHz 1RB Left Cheek High Date/Time: 01/13/2015 Medium: Head 900MHz Medium parameters used (interpolated): f = MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: FDD LTE Band20; Frequency: MHz; Duty Cycle: 1:3.7 Probe: ES3DV3 - SN3252ConvF(6.46, 6.46, 6.46); High Cheek Left LTE Band20 5MHz 1RB/Area Scan (11x7x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = mw/g High Cheek Left LTE Band20 5MHz 1RB/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = db Peak SAR (extrapolated) = mW/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 211 of 299

212 LTE Band20 5MHz 1RB Left Tilt High Date/Time: 01/13/2015 Medium: Head 900MHz Medium parameters used (interpolated): f = MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: FDD LTE Band20; Frequency: MHz; Duty Cycle: 1:3.7 Probe: ES3DV3 - SN3252ConvF(6.46, 6.46, 6.46); High Tilt Left LTE Band20 5MHz 1RB/Area Scan (11x7x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = mw/g High Tilt Left LTE Band20 5MHz 1RB/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = 0.07 db Peak SAR (extrapolated) = mW/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 212 of 299

213 LTE Band20 5MHz 1RB Right Cheek High Date/Time: 01/13/2015 Medium: Head 900MHz Medium parameters used (interpolated): f = MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: FDD LTE Band20; Frequency: MHz; Duty Cycle: 1:3.7 Probe: ES3DV3 - SN3252ConvF(6.46, 6.46, 6.46); High Cheek Right LTE Band20 5MHz 1RB/Area Scan (7x11x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = mw/g High Cheek Right LTE Band20 5MHz 1RB/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = db Peak SAR (extrapolated) = mW/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 213 of 299

214 LTE Band20 5MHz 1RB Right Tilt High Date/Time: 01/13/2015 Medium: Head 900MHz Medium parameters used (interpolated): f = MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: FDD LTE Band20; Frequency: MHz; Duty Cycle: 1:3.7 Probe: ES3DV3 - SN3252ConvF(6.46, 6.46, 6.46); High Tilt Right LTE Band20 5MHz 1RB/Area Scan (7x11x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = mw/g High Tilt Right LTE Band20 5MHz 1RB/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = db Peak SAR (extrapolated) = mW/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 214 of 299

215 LTE Band20 5MHz 12RB Left Cheek High Date/Time: 01/13/2015 Medium: Head 900MHz Medium parameters used (interpolated): f = MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: FDD LTE Band20; Frequency: MHz; Duty Cycle: 1:3.7 Probe: ES3DV3 - SN3252ConvF(6.46, 6.46, 6.46); High Cheek Left LTE Band20 5MHz 12RB/Area Scan (11x7x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = mw/g High Cheek Left LTE Band20 5MHz 12RB/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = 0.15 db Peak SAR (extrapolated) = mW/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 215 of 299

216 LTE Band20 5MHz 12RB Left Tilt High Date/Time: 01/13/2015 Medium: Head 900MHz Medium parameters used (interpolated): f = MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: FDD LTE Band20; Frequency: MHz; Duty Cycle: 1:3.7 Probe: ES3DV3 - SN3252ConvF(6.46, 6.46, 6.46); High Tilt Left LTE Band20 5MHz 12RB/Area Scan (11x7x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = mw/g High Tilt Left LTE Band20 5MHz 12RB/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = 0.08 db Peak SAR (extrapolated) = mW/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 216 of 299

217 LTE Band20 5MHz 12RB Right Cheek High Date/Time: 01/13/2015 Medium: Head 900MHz Medium parameters used (interpolated): f = MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: FDD LTE Band20; Frequency: MHz; Duty Cycle: 1:3.7 Probe: ES3DV3 - SN3252ConvF(6.46, 6.46, 6.46); High Cheek Right LTE Band20 5MHz 12RB/Area Scan (7x11x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = mw/g High Cheek Right LTE Band20 5MHz 12RB/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = db Peak SAR (extrapolated) = mW/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 217 of 299

218 LTE Band20 5MHz 12RB Right Tilt High Date/Time: 01/13/2015 Medium: Head 900MHz Medium parameters used (interpolated): f = MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: FDD LTE Band20; Frequency: MHz; Duty Cycle: 1:3.7 Probe: ES3DV3 - SN3252ConvF(6.46, 6.46, 6.46); High Tilt Right LTE Band20 5MHz 12RB/Area Scan (7x11x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = mw/g High Tilt Right LTE Band20 5MHz 12RB/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = 0.14 db Peak SAR (extrapolated) = mW/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 218 of 299

219 LTE Band20 5MHz 1RB Right Cheek Middle Date/Time: 01/13/2015 Medium: Head 900MHz Medium parameters used: f = 847 MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: FDD LTE Band20; Frequency: 847 MHz; Duty Cycle: 1:3.7 Probe: ES3DV3 - SN3252ConvF(6.46, 6.46, 6.46); Middle Cheek Right LTE Band20 5MHz 1RB/Area Scan (7x11x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = mw/g Middle Cheek Right LTE Band20 5MHz 1RB/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = db Peak SAR (extrapolated) = mW/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 219 of 299

220 LTE Band20 5MHz 1RB Right Cheek Low Date/Time: 01/13/2015 Medium: Head 900MHz Medium parameters used (interpolated): f = MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: FDD LTE Band20; Frequency: MHz; Duty Cycle: 1:3.7 Probe: ES3DV3 - SN3252ConvF(6.46, 6.46, 6.46); Low Cheek Right LTE Band20 5MHz 1RB/Area Scan (7x11x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = mw/g Low Cheek Right LTE Band20 5MHz 1RB/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = db Peak SAR (extrapolated) = mW/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 220 of 299

221 LTE Band20 20MHz 1RB Right Cheek High Date/Time: 01/13/2015 Medium: Head 900MHz Medium parameters used: f = 852 MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: FDD LTE Band20; Frequency: 852 MHz; Duty Cycle: 1:3.7 Probe: ES3DV3 - SN3252ConvF(6.46, 6.46, 6.46); High Cheek Right LTE Band20 20MHz 1RB/Area Scan (7x11x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = mw/g High Cheek Right LTE Band20 20MHz 1RB/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = db Peak SAR (extrapolated) = mW/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 221 of 299

222 LTE Band20 15MHz 1RB Right Cheek High Date/Time: 01/13/2015 Medium: Head 900MHz Medium parameters used (interpolated): f = MHz; σ = 0.91 mho/m;εr = 41.78; ρ = 1000 kg/m3 Communication System: FDD LTE Band20; Frequency: MHz; Duty Cycle: 1:3.7 Probe: ES3DV3 - SN3252ConvF(6.46, 6.46, 6.46); High Cheek Right LTE Band20 15MHz 1RB/Area Scan (7x11x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = mw/g High Cheek Right LTE Band20 15MHz 1RB/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = db Peak SAR (extrapolated) = mW/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 222 of 299

223 LTE Band20 10MHz 1RB Right Cheek High Date/Time: 01/13/2015 Medium: Head 900MHz Medium parameters used: f = 857 MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: FDD LTE Band20; Frequency: 857 MHz; Duty Cycle: 1:3.7 Probe: ES3DV3 - SN3252ConvF(6.46, 6.46, 6.46); High Cheek Right LTE Band20 10MHz 1RB/Area Scan (7x11x1): Measurement grid: dx=15mm, dy=15mm Maximum value of SAR (measured) = mw/g High Cheek Right LTE Band20 10MHz 1RB/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = db Peak SAR (extrapolated) = mW/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 223 of 299

224 LTE Band20 5MHz 1RB Toward Ground High Date/Time: 01/13/2015 Medium: Head 900MHz Medium parameters used (interpolated): f = MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: FDD LTE Band20; Frequency: MHz; Duty Cycle: 1:3.7 Probe: ES3DV3 - SN3252ConvF(6.46, 6.46, 6.46); High Toward Ground LTE Band20 5MHz 1RB/Area Scan (10x16x1): Measurement grid: dx=10mm, dy=10mm Maximum value of SAR (measured) = mw/g High Toward Ground LTE Band20 5MHz 1RB/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = db Peak SAR (extrapolated) = mW/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 224 of 299

225 LTE Band20 5MHz 1RB Toward Phantom High Date/Time: 01/13/2015 Medium: Head 900MHz Medium parameters used (interpolated): f = MHz; σ = mho/m;εr = ; ρ = 1000 kg/m3 Communication System: FDD LTE Band20; Frequency: MHz; Duty Cycle: 1:3.7 Probe: ES3DV3 - SN3252ConvF(6.46, 6.46, 6.46); High Toward Phantom LTE Band20 5MHz 1RB/Area Scan (10x16x1): Measurement grid: dx=10mm, dy=10mm Maximum value of SAR (measured) = mw/g High Toward Phantom LTE Band20 5MHz 1RB/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = V/m; Power Drift = db Peak SAR (extrapolated) = mW/g SAR(1 g) = mw/g; SAR(10 g) = mw/g Maximum value of SAR (measured) = mw/g East China Institute of Telecommunications Page Number : 225 of 299

SAMSUNG GT-S5369 (mobile phone) Serial number: IMEI 358858043716587. Mr. Antoine SAMAKH and Mr. Mathieu SAMAKH 92100 FRANCE

SAMSUNG GT-S5369 (mobile phone) Serial number: IMEI 358858043716587. Mr. Antoine SAMAKH and Mr. Mathieu SAMAKH 92100 FRANCE R052-DAS-12-104374-7/A Ed. 1 This report cancels and replaces the test report R052-DAS-12-104374-7/A Ed. 0 SAR TEST REPORT According to the standard: EN 62209-1: 2006 Equipment under test: Antenna patch

More information

SAR TEST REPORT. According to the standard: EN 62209-1: 2006

SAR TEST REPORT. According to the standard: EN 62209-1: 2006 R052-DAS-12-104374-2/A Ed. 1 This report cancels and replaces the test report R052-DAS-12-104374-2/A Ed. 0 SAR TEST REPORT According to the standard: EN 62209-1: 2006 Equipment under test: Antenna patch

More information

SAR Test Report: Type Number FAD-3022012-BV; FCC ID PY7FD022012; IC 4170B-FD022012

SAR Test Report: Type Number FAD-3022012-BV; FCC ID PY7FD022012; IC 4170B-FD022012 1 (34) Report issued by an Accredited Laboratory Rapport utfärdad av ett ackrediterat laboratorium This laboratory is accredited to SS-EN ISO/IEC 17025 (SWEDAC accreditation no. 1761). SAR Test Report:

More information

FCC OET BULLETIN 65 SUPPLEMENT C 01-01 IEEE Std 1528-2003 and 1528a-2005. (Class II Permissive Change) SAR EVALUATION REPORT. For.

FCC OET BULLETIN 65 SUPPLEMENT C 01-01 IEEE Std 1528-2003 and 1528a-2005. (Class II Permissive Change) SAR EVALUATION REPORT. For. FCC OET BULLETIN 65 SUPPLEMENT C 01-01 IEEE Std 1528-2003 and 1528a-2005 (Class II Permissive Change) SAR EVALUATION REPORT For Glass Model: XEB Report Number: 13U14955-5A Issue Date: 4/15/2013 Prepared

More information

Body SAR and EU. B. Derat

Body SAR and EU. B. Derat Body SAR and EU B. Derat Overview / Outline New Approach: Directive / Standards Current applicable standard IEC/EN 62209-2:2010 Tablet case study Future of EU body SAR testing Maintenance of IEC 62209-2

More information

Radio Frequency (RF) Exposure Compliance of Radiocommunication Apparatus (All Frequency Bands)

Radio Frequency (RF) Exposure Compliance of Radiocommunication Apparatus (All Frequency Bands) Issue 3 June 2009 Spectrum Management and Telecommunications Radio Standards Specification Radio Frequency (RF) Exposure Compliance of Radiocommunication Apparatus (All Frequency Bands) Aussi disponible

More information

DECLARATION OF COMPLIANCE - SAR RF EXPOSURE EVALUATION - EU EN 62311:2008

DECLARATION OF COMPLIANCE - SAR RF EXPOSURE EVALUATION - EU EN 62311:2008 DECLARATION OF COMPLIANCE - SAR RF EXPOSURE EVALUATION - EU EN 62311:2008 Test Lab Information Name Address CELLTECH LABS INC. 21-364 Lougheed Road, Kelowna, B.C. V1X 7R8 Canada Test Lab Accreditation(s)

More information

For many years the general public

For many years the general public David Seabury, ETS-Lindgren An Update On SAR Standards And The Basic Requirements For SAR Assessment For many years the general public has been concerned about the possible health effects of exposure to

More information

September 26, 2000 IMST GmbH Carl-Friedrich-Gauß-Str. 2 D-47475 Kamp-Lintfort

September 26, 2000 IMST GmbH Carl-Friedrich-Gauß-Str. 2 D-47475 Kamp-Lintfort TTI-P-G 158 Report Dosimetric Assessment of the Mobile Ericsson T18z with an without the PAM System Technologies devices According to the American FCC Requirements September 26, 2000 IMST GmbH Carl-Friedrich-Gauß-Str.

More information

EN 50360:2001+A1:2012 SAR EVALUATION REPORT. Baoji Jiayuyutong electronic co.,ltd

EN 50360:2001+A1:2012 SAR EVALUATION REPORT. Baoji Jiayuyutong electronic co.,ltd EN 50360:2001+A1:2012 SAR EVALUATION REPORT For Baoji Jiayuyutong electronic co.,ltd Building A, 28# Longteng Street, Jianyi Village, Henggang Town, Longgang District, Shenzhen, P. R. China Model: JY-S3

More information

Human Exposure Limits

Human Exposure Limits Human Exposure Limits Session 3 0 Version December 2014 Learning objectives In this session we will: Learn about the international exposure limits for workers and the public Learn about methods for assessing

More information

Specific Absorption Rate (SAR) Test Report for FIC (First International Computer, Inc.) on the Neo 1973

Specific Absorption Rate (SAR) Test Report for FIC (First International Computer, Inc.) on the Neo 1973 Specific Absorption Rate (SAR) Test Report for FIC (First International Computer, Inc.) on the Neo 1973 Report No. : EA721310-1-1-01 Trade Name : FIC Model No. : GTA01BV4 Date of Testing : May 29 and 30,

More information

Federal Communications Commission Office of Engineering and Technology Laboratory Division Public Draft Review

Federal Communications Commission Office of Engineering and Technology Laboratory Division Public Draft Review April 23, 2012 Federal Communications Commission Office of Engineering and Technology Laboratory Division Public Draft Review Draft Laboratory Division Publications Report Title: General RF Exposure Policies

More information

IEC TC106. Standards for the Assessment of Human Exposure to Electric, Magnetic, and Electromagnetic Fields, 0 to 300 GHz

IEC TC106. Standards for the Assessment of Human Exposure to Electric, Magnetic, and Electromagnetic Fields, 0 to 300 GHz International Electrotechnical Commission IEC TC106 Standards for the Assessment of Human Exposure to Electric, Magnetic, and Electromagnetic Fields, 0 to 300 GHz R. C. Petersen Chairman Secretariat and

More information

RF EXPOSURE PROCEDURES AND EQUIPMENT AUTHORIZATION POLICIES FOR MOBILE AND PORTABLE DEVICES

RF EXPOSURE PROCEDURES AND EQUIPMENT AUTHORIZATION POLICIES FOR MOBILE AND PORTABLE DEVICES Federal Communications Commission Office of Engineering and Technology Laboratory Division October 23, 2015 RF EXPOSURE PROCEDURES AND EQUIPMENT AUTHORIZATION POLICIES FOR MOBILE AND PORTABLE DEVICES Table

More information

RF Exposure Procedures TCB Workshop October 2012

RF Exposure Procedures TCB Workshop October 2012 RF Exposure Procedures TCB Workshop October 2012 Laboratory Division Office of Engineering and Technology Federal Communications Commission Overview Further updates on the RF exposure KDB drafts released

More information

Assessment of Human Exposure to Electromagnetic Radiation from Wireless Devices in Home and Office Environments

Assessment of Human Exposure to Electromagnetic Radiation from Wireless Devices in Home and Office Environments Assessment of Human Exposure to Electromagnetic Radiation from Wireless Devices in Home and Office Environments Sven Kühn, Urs Lott, Axel Kramer, Niels Kuster Foundation for Research on Information Technologies

More information

Compliance Testing of Mobile Phones. Masao Taki Tokyo Metropolitan University JAPAN

Compliance Testing of Mobile Phones. Masao Taki Tokyo Metropolitan University JAPAN Compliance Testing of Mobile Phones Masao Taki Tokyo Metropolitan University JAPAN Outline Exposure Standards/Guidelines Product Standard of MTE and Standard Procedures of Compliance Testing Some remarks

More information

The range of RF spans 3 KHz (3000 Hz) to 300 GHz (300 million Hz)

The range of RF spans 3 KHz (3000 Hz) to 300 GHz (300 million Hz) 1 2 The range of RF spans 3 KHz (3000 Hz) to 300 GHz (300 million Hz) Frequencies of RF devices range from the low frequency AM broadcasts (80 MHz) to higher frequency mobile phones (1900 MHz) smart meters

More information

CERTIFICATE OF COMPLIANCE SAR EVALUATION

CERTIFICATE OF COMPLIANCE SAR EVALUATION 802 N. Twin Oaks Valley Road, Suite 105 San Marcos, CA 92069 U.S.A. TEL (760) 471-2100 FAX (760) 471-2121 http://www.rfexposurelab.com CERTIFICATE OF COMPLIANCE SAR EVALUATION LS Research Dates of Test:

More information

Millennium Product Inc. Model: Cell Shield / Zorb

Millennium Product Inc. Model: Cell Shield / Zorb Millennium Product Inc. Cell Shield / Zorb Prepared by PCTEST LAB Issued on: 10/22/2015 Report Version 2.6 NOTE: SAR results only apply to the device tested. Although the device may have had different

More information

SAR ASSOCIATED WITH THE USE OF HANDS-FREE MOBILE TELEPHONES

SAR ASSOCIATED WITH THE USE OF HANDS-FREE MOBILE TELEPHONES SAR ASSOCIATED WITH THE USE OF HANDS-FREE MOBILE TELEPHONES S.J. Porter, M.H. Capstick, F. Faraci, I.D. Flintoft and A.C. Marvin Department of Electronics, University of York Heslington, York, YO10 5DD,

More information

Technical limits of Human Exposure to RF from Cellular Base Stations and Handsets

Technical limits of Human Exposure to RF from Cellular Base Stations and Handsets Ministry of Environmental Protection Ministry of Communications Technical limits of Human Exposure to RF from Cellular Base Stations and Handsets Based on author s PhD thesis/book- An analysis of regulatory

More information

SAR Comparison Report

SAR Comparison Report Page: 1 of 12 SAR Comparison Report Reference Number: 3103519 Report Number: 3103519EMC01 Revision Level: 0 Client: Lifewave Equipment Under Test: Model Name: Matrix 2 Test Protocol: SAR Comparison Report

More information

RF EXPOSURE LIMITS AND TESTING REQUIREMENTS

RF EXPOSURE LIMITS AND TESTING REQUIREMENTS RF EXPOSURE LIMITS AND TESTING REQUIREMENTS Jay Moulton Vice President March 12, 2013 1 OVERVIEW Specific Absorption Rate (SAR) and Maximum Permissible Exposure (MPE) Standards and Limits Evaluation Methods

More information

Evaluating Compliance with FCC Guidelines for Human Exposure to Radiofrequency Electromagnetic Fields

Evaluating Compliance with FCC Guidelines for Human Exposure to Radiofrequency Electromagnetic Fields Federal Communications Commission Office of Engineering & Technology Evaluating Compliance with FCC Guidelines for Human Exposure to Radiofrequency Electromagnetic Fields Additional Information for Evaluating

More information

The field strength measurement and SAR experience related to human exposure in 110 MHz to 40 GHz

The field strength measurement and SAR experience related to human exposure in 110 MHz to 40 GHz The field strength measurement and SAR experience related to human exposure in 110 MHz to 40 GHz J. Klima, R. Ščehovič Department of Physics, Faculty of Natural Sciences, University of Mathias Bel, Tajovského

More information

Effects of Mobile Phone Radiation onto Human Head with Variation of Holding Cheek and Tilt Positions

Effects of Mobile Phone Radiation onto Human Head with Variation of Holding Cheek and Tilt Positions Effects of Mobile Phone Radiation onto Human Head with Variation of Holding Cheek and Tilt Positions M. R. Iqbal-Faruque* 1, N. Aisyah-Husni 2, Md. Ikbal-Hossain 1, M. Tariqul-Islam 2 and N. Misran 2 1

More information

Federal Communications Commission Office of Engineering and Technology Laboratory Division

Federal Communications Commission Office of Engineering and Technology Laboratory Division October 24, 2012 Federal Communications Commission Office of Engineering and Technology Laboratory Division Mobile and Portable Devices RF Exposure Procedures and Equipment Authorization Policies Table

More information

Evaluating Cell Phone and Personal Communications Equipment and their EMC Effects on Automotive Audio and In-Cabin Modules

Evaluating Cell Phone and Personal Communications Equipment and their EMC Effects on Automotive Audio and In-Cabin Modules Evaluating Cell Phone and Personal Communications Equipment and their EMC Effects on Automotive Audio and In-Cabin Modules Craig W. Fanning Elite Electronic Engineering, Inc. 1516 Centre Circle Downers

More information

Specific Absorption Rate (SAR) Test Report

Specific Absorption Rate (SAR) Test Report Specific Absorption Rate (SAR) Test Report for FIC (First International Computer, Inc.) on the Neo FreeRunner Report No. : EA832514 Trade Name : OPENMOKO Model Name : GTA02 Date of Testing : Jan. 04, 2008

More information

3GPP TS V8.3.0 ( )

3GPP TS V8.3.0 ( ) TS 51.026 V8.3.0 (2010-03) Technical Specification 3rd Generation Partnership Project; Technical Specification Group GSM/EDGE Radio Access Network; Base Station System (BSS) equipment specification; Part

More information

R&D TESTING SAR EVALUATION

R&D TESTING SAR EVALUATION 802 N. Twin Oaks Valley Road, Suite 105 San Marcos, CA 92069 U.S.A. TEL (760) 471-2100 FAX (760) 471-2121 http://www.rfexposurelab.com R&D TESTING SAR EVALUATION Bodywell Chip Dates of Test: February 5,

More information

Overview of RF Exposure Concepts and Requirements

Overview of RF Exposure Concepts and Requirements Overview of RF Exposure Concepts and Requirements Kwok Chan Technical Research Branch Federal Communications Commission Office of Engineering and Technology Laboratory Division Note: hyperlinks may not

More information

Rated Power(W) 8W 2. EG-LED0840-01 8W 3. EG-LED1027-01 10W

Rated Power(W) 8W 2. EG-LED0840-01 8W 3. EG-LED1027-01 10W 14713221 001 Seite 2 von 37 Page 2 of 37 Model List: No Model Rated Voltage(V) 1. EG-LED0827-01 Rated Power(W) 8W 2. EG-LED0840-01 8W 3. EG-LED1027-01 10W 4. EG-LED1040-01 AC 100-240V, 10W 5. EG-LED1027-02

More information

TCB RF Exposure Training

TCB RF Exposure Training TCB RF Exposure Training RF Exposure (RFx( RFx) ) Coming Attractions Goals for Exclusion List Handoff Exposure Categories and Considerations Collocated Devices Tim Harrington, FCC/OET/EAB February 13-15,

More information

Temperature Rise Measurements

Temperature Rise Measurements Chapter 22 Temperature Rise Measurements 22.1 Background The SAR in tissue simulating liquid can be assessed by means of temperature rise or by measurements of induced electric field. SAR = c T dt (22.1)

More information

Evaluating Compliance with FCC Guidelines for Human Exposure to Radiofrequency Electromagnetic Fields

Evaluating Compliance with FCC Guidelines for Human Exposure to Radiofrequency Electromagnetic Fields Federal Communications Commission Office of Engineering & Technology Evaluating Compliance with FCC Guidelines for Human Exposure to Radiofrequency Electromagnetic Fields Additional Information for Evaluating

More information

RICHARD T ELL ASSOCIATES,INC.

RICHARD T ELL ASSOCIATES,INC. RICHARD T ELL ASSOCIATES,INC. An Evaluation of Test Measurement Data Obtained on the KW-Gard RF Protective Suit March 30, 1998 Prepared for Euclid Garment Manufacturing Company 333 Martinel Drive Kent,

More information

PXI. www.aeroflex.com. GSM/EDGE Measurement Suite

PXI. www.aeroflex.com. GSM/EDGE Measurement Suite PXI GSM/EDGE Measurement Suite The GSM/EDGE measurement suite is a collection of software tools for use with Aeroflex PXI 3000 Series RF modular instruments for characterising the performance of GSM/HSCSD/GPRS

More information

Specific Absorption Rate (SAR) in the head of Tablet user's

Specific Absorption Rate (SAR) in the head of Tablet user's 7th Latin American Workshop On Communications - 2015 Specific Absorption Rate (SAR) in the head of Tablet user's Juliana Borges Ferreira Post-graduation program in Electrical Engineering Federal University

More information

EN 301 489-17 v1.2.1 TEST REPORT FOR. 802.11ag/Draft 802.11n WLAN PCI-E Mini Card MODEL NUMBER: BCM94322MC REPORT NUMBER: 07U11529-5

EN 301 489-17 v1.2.1 TEST REPORT FOR. 802.11ag/Draft 802.11n WLAN PCI-E Mini Card MODEL NUMBER: BCM94322MC REPORT NUMBER: 07U11529-5 EN 301 489-17 v1.2.1 TEST REPORT FOR 802.11ag/Draft 802.11n WLAN PCI-E Mini Card MODEL NUMBER: BCM94322MC REPORT NUMBER: 07U11529-5 ISSUE DATE: JANUARY 29, 2008 Prepared for BROADCOM CORPORATION 190 MATHILDA

More information

Synthetic Sensing: Proximity / Distance Sensors

Synthetic Sensing: Proximity / Distance Sensors Synthetic Sensing: Proximity / Distance Sensors MediaRobotics Lab, February 2010 Proximity detection is dependent on the object of interest. One size does not fit all For non-contact distance measurement,

More information

RF Exposure and Modular Equipment. Considerations

RF Exposure and Modular Equipment. Considerations RF Exposure and Modular Equipment Considerations RF Exposure Rules SAR and MPE Estimation Summary Based on current interpretations of US radio law by FCC Based upon the TCB Exclusion List and various interpretations

More information

Impedance 50 (75 connectors via adapters)

Impedance 50 (75 connectors via adapters) VECTOR NETWORK ANALYZER PLANAR TR1300/1 DATA SHEET Frequency range: 300 khz to 1.3 GHz Measured parameters: S11, S21 Dynamic range of transmission measurement magnitude: 130 db Measurement time per point:

More information

Continuous, remote monitoring and logging of electromagnetic fields

Continuous, remote monitoring and logging of electromagnetic fields MULTI-BAND EMF AREA MONITOR AMB-8057-03/G Continuous, remote monitoring and logging of electromagnetic fields Discrimination of GSM and UMTS contributions to total EMF values Electric field monitoring

More information

Specific Absorption Rate (SAR) Induced in Human Heads of Various Sizes When Using a Mobile Phone

Specific Absorption Rate (SAR) Induced in Human Heads of Various Sizes When Using a Mobile Phone , June 30 - July 2, 2010, London, U.K. Specific Absorption Rate (SAR) Induced in Human Heads of Various Sizes When Using a Mobile Phone Adel Z. El Dein Alaeddin Amr Abstract - This paper analyzes the specific

More information

Design and Certification of ASH Radio Systems for Japan

Design and Certification of ASH Radio Systems for Japan Design and Certification of ASH Radio Systems for Japan RFM s second-generation ASH radio hybrids are being used in a wide variety of applications in Japan, operating under the Japanese BIJAKU radio regulations.

More information

ARIB TR-T12-34.925 V3.0.0. Specific Absorption Rate (SAR) requirements and regulations in different regions

ARIB TR-T12-34.925 V3.0.0. Specific Absorption Rate (SAR) requirements and regulations in different regions ARIB TR-T12-34.925 V3.0.0 Specific Absorption Rate (SAR) requirements and regulations in different regions Refer to "Notice" in the preface of ARIB TR-T12 for Copyrights. Technical Report 3rd Generation

More information

Applications of CST to modelling human interaction with EM fields: a metrological perspective. Benjamin Loader Date 6 Aug 2013

Applications of CST to modelling human interaction with EM fields: a metrological perspective. Benjamin Loader Date 6 Aug 2013 Applications of CST to modelling human interaction with EM fields: a metrological perspective. Benjamin Loader Date 6 Aug 2013 Contents 1. Introduction 2. Accuracy of models. 3. Some applications at NPL

More information

EMR-300 Broadband RF Survey Meter

EMR-300 Broadband RF Survey Meter Electric d Magnetic Field Measurement EMR-300 Broadbd RF Survey Meter Available with Isotropic Probes to cover 3 khz to 60 GHz Easy-to-Use Design Lightweight d Rugged Cost Effective Fully Automatic Zeroing

More information

SAR TESTS ON MOBILE PHONES USED WITH AND WITHOUT PERSONAL HANDS-FREE KITS

SAR TESTS ON MOBILE PHONES USED WITH AND WITHOUT PERSONAL HANDS-FREE KITS SARTest Report 0083 July 2000 SAR TESTS ON MOBILE PHONES USED WITH AND WITHOUT PERSONAL HANDS-FREE KITS MI Manning and CHB Gabriel Report prepared for DTI. Page 1 of 17 Indemnity Sartest Limited makes

More information

Scanning with Sony Ericsson TEMS Phones. Technical Paper

Scanning with Sony Ericsson TEMS Phones. Technical Paper Scanning with Sony Ericsson TEMS Phones Technical Paper Scanning with Sony Ericsson TEMS Phones 2009-05-13 Ascom 2009. All rights reserved. TEMS is a trademark of Ascom. All other trademarks are the property

More information

SAR Distribution in Test Animals Exposed to RF Radiation

SAR Distribution in Test Animals Exposed to RF Radiation German Mobile Telecommunication Research Programme, July 25th, 2006 SAR Distribution in Test Animals Exposed to RF Radiation Verónica Berdiñas Torres, Andreas Christ, Niels Kuster IT IS Foundation, ETH

More information

Product Information S N O. Portable VIP protection CCTV & Alarm System 2

Product Information S N O. Portable VIP protection CCTV & Alarm System 2 Product Information S N O Portable VIP protection CCTV & Alarm System 2 G O V E R N M E N T A L S E C U R I T Y S O L U T I VIP KIT Rapid Deployment VIP Protection Kit The VIP KIT has been designed to

More information

Human Exposure to Outdoor PLC System

Human Exposure to Outdoor PLC System 1602 PIERS Proceedings, Marrakesh, MOROCCO, March 20 23, 2011 Human Exposure to Outdoor PLC System Vicko Doric 1, Dragan Poljak 1, and Khalil El Khamlichi Drissi 2 1 University of Split, Croatia 2 Blaise

More information

Effect of Metallic Materials on SAR

Effect of Metallic Materials on SAR Contemporary Engineering Sciences, Vol. 5, 2012, no. 9, 407-411 Effect of Metallic Materials on SAR Asma Lak Department of Electrical Engineering, Genaveh branch Islamic Azad University, Genaveh, Iran

More information

Measurement of RF Emissions from a Final Coat Electronics Corrosion Module

Measurement of RF Emissions from a Final Coat Electronics Corrosion Module Engineering Test Report No. 37802-02 Rev. A Measurement of RF Emissions from a Final Coat Electronics Corrosion Module For : Canadian Auto Preservation, Inc. 390 Bradwick Drive Concord, Ontario CANADA

More information

Selected Radio Frequency Exposure Limits

Selected Radio Frequency Exposure Limits ENVIRONMENT, SAFETY & HEALTH DIVISION Chapter 50: Non-ionizing Radiation Selected Radio Frequency Exposure Limits Product ID: 94 Revision ID: 1736 Date published: 30 June 2015 Date effective: 30 June 2015

More information

INTRODUCTION TO COMMUNICATION SYSTEMS AND TRANSMISSION MEDIA

INTRODUCTION TO COMMUNICATION SYSTEMS AND TRANSMISSION MEDIA COMM.ENG INTRODUCTION TO COMMUNICATION SYSTEMS AND TRANSMISSION MEDIA 9/6/2014 LECTURES 1 Objectives To give a background on Communication system components and channels (media) A distinction between analogue

More information

RF safety at base station sites

RF safety at base station sites RF safety at base station sites CONTENTS 1 Purpose and scope................................................. 2 2 Introduction........................................................ 2 3 Basic information...................................................

More information

Annex to the joint statement: Exposure of the general public to radiofrequency fields

Annex to the joint statement: Exposure of the general public to radiofrequency fields 16 November 2009 Annex to the joint statement: Exposure of the general public to radiofrequency fields 1. Introduction This document presents typical exposure of the general public to radiofrequency (RF)

More information

RF Exposure Evaluation Report

RF Exposure Evaluation Report RF Exposure Evaluation Report APPLICANT EQUIPMENT BRAND NAME MODEL NAME FCC ID FILING TYPE : TomTom International BV : GPS Navigation System : TomTom : 4CR51 : S4L4CR51 : Certification STANDARD : OET Bulletin

More information

Spectrum and Power Measurements Using the E6474A Wireless Network Optimization Platform

Spectrum and Power Measurements Using the E6474A Wireless Network Optimization Platform Application Note Spectrum and Power Measurements Using the E6474A Wireless Network Optimization Platform By: Richard Komar Introduction With the rapid development of wireless technologies, it has become

More information

Technical Datasheet Scalar Network Analyzer Model 8003-10 MHz to 40 GHz

Technical Datasheet Scalar Network Analyzer Model 8003-10 MHz to 40 GHz Technical Datasheet Scalar Network Analyzer Model 8003-10 MHz to 40 GHz The Giga-tronics Model 8003 Precision Scalar Network Analyzer combines a 90 db wide dynamic range with the accuracy and linearity

More information

LTE enodeb Installation and Maintenance Tests

LTE enodeb Installation and Maintenance Tests Application Note LTE enodeb Installation and Maintenance Tests Introduction The Long-Term Evolution (LTE) specifications are defined by the Third Generation Partnership Project (3GPP), which is part of

More information

Transceiver mod. XTR-434

Transceiver mod. XTR-434 Transceiver mod. XTR-434 Miniaturized data transceiver module, 100Kbps maximum speed, 433,92 MHz operating frequency. Pin-Out and Block diagram Dimensions 1 GND 2 Antenna RX-TX switch Ampl. PLL Controlled

More information

ETSI EN 302 774 V1.2.1 (2012-02)

ETSI EN 302 774 V1.2.1 (2012-02) EN 302 774 V1.2.1 (2012-02) Harmonized European Standard Broadband Wireless Access Systems (BWA) in the 3 400 MHz to 3 800 MHz frequency band; Base Stations; Harmonized EN covering the essential requirements

More information

Mobile Phone SAR Analysis through Experimental and Numerical Simulation

Mobile Phone SAR Analysis through Experimental and Numerical Simulation 2010, 12th International Conference on Optimization of Electrical and Electronic Equipment, OPTIM 2010 Mobile Phone SAR Analysis through Experimental and Numerical Simulation Mihaela Morega 1, Andrei Marinescu

More information

Wireless Broadband: Health & Safety Information

Wireless Broadband: Health & Safety Information Wireless Broadband: Health & Safety Information Introduction The increasing use of mobile phones and other wireless technology has been accompanied by public debate about possible adverse effects on health.

More information

Continuous, remote monitoring and logging of electromagnetic fields

Continuous, remote monitoring and logging of electromagnetic fields MULTI-BAND EMF AREA MONITOR AMB-8057 Continuous, remote monitoring and logging of electromagnetic fields Discrimination of GSM and UMTS contributions to total emf values Magnetic fields monitoring from

More information

FCC CFR47 PART 15 SUBPART C CERTIFICATION TEST REPORT FOR. MODEL NUMBER: WRT54G v7 FCC ID: Q87-WT54GV70 REPORT NUMBER: 06U

FCC CFR47 PART 15 SUBPART C CERTIFICATION TEST REPORT FOR. MODEL NUMBER: WRT54G v7 FCC ID: Q87-WT54GV70 REPORT NUMBER: 06U FCC CFR47 PART 15 SUBPART C CERTIFICATION TEST REPORT FOR WIRELESS-G BROADBAND ROUTER WITH 4-PORT SWITCH MODEL NUMBER: WRT54G v7 FCC ID: Q87-WT54GV70 REPORT NUMBER: 06U10091-1 ISSUE DATE: FEBRUARY 21,

More information

Exposures to radiofrequency fields from WiFi in New Zealand schools

Exposures to radiofrequency fields from WiFi in New Zealand schools Exposures to radiofrequency fields from WiFi in New Zealand schools Report 2014/02 This report was prepared for: Ministry of Health P O Box 5013 Wellington Report prepared by: Martin Gledhill Finalised:

More information

3D SCANNERTM. 3D Scanning Comes Full Circle. s u n. Your Most Valuable QA and Dosimetry Tools A / B / C. The 3D SCANNER Advantage

3D SCANNERTM. 3D Scanning Comes Full Circle. s u n. Your Most Valuable QA and Dosimetry Tools A / B / C. The 3D SCANNER Advantage 3D SCANNERTM 3D Scanning Comes Full Circle Relative 3D Dosimetry offering the easiest setup, most objectivity, and best consistency available The 3D SCANNER Advantage Advanced Design Ring and diameter

More information

Human exposure to RF

Human exposure to RF INTERNATIONAL ELECTROTECHNICAL COMMISSION Human exposure to RF Don Heirman ACEC/TC106 Liaison Representative APEMC symposium May 2015 Copyright IEC, Geneva, Switzerland TC106 Scope To prepare international

More information

Transceiver mod. XTR-434

Transceiver mod. XTR-434 XTR-434xxx Transceiver mod. XTR-434 Miniaturized data transceiver modules, 100 Kbps [XTR-434], or 50 Kbps [XTR-434L] maximum speed, 433.92 MHz operating frequency. Pin-Out and Block diagram Dimensions

More information

Measuring electric and magnetic fields

Measuring electric and magnetic fields NARDA BROADBAND FIELD METER NBM-520 Measuring electric and magnetic fields ranging from high frequency to microwaves Non-directional measurement using isotropic probes for applications in the frequency

More information

Voice services over Adaptive Multi-user Orthogonal Sub channels An Insight

Voice services over Adaptive Multi-user Orthogonal Sub channels An Insight TEC Voice services over Adaptive Multi-user Orthogonal Sub channels An Insight HP 4/15/2013 A powerful software upgrade leverages quaternary modulation and MIMO techniques to improve network efficiency

More information

WIRELESS INSTRUMENTATION TECHNOLOGY

WIRELESS INSTRUMENTATION TECHNOLOGY BS&B WIRELESS, L.L.C. BS&B WIRELESS, L.L.C. WIRELESS INSTRUMENTATION TECHNOLOGY Printed February 2004 BS&B WIRELESS, L.L.C. 7422-B East 46th Place, Tulsa, OK74145 Phone: 918-622-5950 Fax: 918-665-3904

More information

XTR-869 mod. Transceiver

XTR-869 mod. Transceiver mod. Transceiver Miniaturized data transceiver module, 100 Kbps maximum speed, 869,85 MHz operating frequency. Band without any duty-cycle restriction in the use time (100%). Pin-Out and block diagram

More information

RX-AM4SF Receiver. Pin-out. Connections

RX-AM4SF Receiver. Pin-out. Connections RX-AM4SF Receiver The super-heterodyne receiver RX-AM4SF can provide a RSSI output indicating the amplitude of the received signal: this output can be used to create a field-strength meter capable to indicate

More information

R&S R-Line Compact Test Chamber Precise measurements of radiated emissions of wireless terminals 800 MHz to 18 GHz

R&S R-Line Compact Test Chamber Precise measurements of radiated emissions of wireless terminals 800 MHz to 18 GHz Test & Measurement Data Sheet 02.00 R&S R-Line Compact Test Chamber Precise measurements of radiated emissions of wireless terminals 800 MHz to 18 GHz R&S R-Line Compact Test Chamber At a glance The R-Line

More information

RL HW / RL HW+ / RL HGW / RL HV / RL HVPW/RL HVPW-G

RL HW / RL HW+ / RL HGW / RL HV / RL HVPW/RL HVPW-G Auto-Levelling Rotary Laser Level RL HW / RL HW+ / RL HGW / RL HV / RL HVPW/RL HVPW-G 77-496 / 77-429 / 77-439 / 77-497 / 77-427/ 77-441 Please read these instructions before operating the product Auto-Levelling

More information

Consequence for a dualband application

Consequence for a dualband application rel. bandwidth -6dB [%] DESIGN CONSIDERATIONS FOR INTEGRATED MOBILE PHONE ANTENNAS D. Manteuffel, A. Bahr, D. Heberling, I. Wolff IMST GmbH, Germany, e-mail: manteuffel@imst.de Abstract Based on the investigation

More information

Key Features. Multiple Operation Modes ENH500 can operate into four different modes with Access Point, Client Bridge, Client Router and WDS Mode.

Key Features. Multiple Operation Modes ENH500 can operate into four different modes with Access Point, Client Bridge, Client Router and WDS Mode. 802.11a/n Long Range Wireless Outdoor CPE Key Features IEEE 802.11 a/n compliant Up to 300Mbps (5GHz) 24V Proprietary PoE support Waterproof Housing IP65 rated AP/CB/CR/WDS Modes 4 SSIDs support + VLAN

More information

RF Measurements Using a Modular Digitizer

RF Measurements Using a Modular Digitizer RF Measurements Using a Modular Digitizer Modern modular digitizers, like the Spectrum M4i series PCIe digitizers, offer greater bandwidth and higher resolution at any given bandwidth than ever before.

More information

Remarkable achievements

Remarkable achievements Remarkable achievements 149.2 km link over water providing 8E1 throughput with 99,99% annual availability Radio link transmitting data from 25km height in Stratosphere to 149km ground station Largest MW

More information

LTE: Technology and Health. 4G and Mobile Broadband

LTE: Technology and Health. 4G and Mobile Broadband LTE: Technology and Health 4G and Mobile Broadband LTE Technology and Health Mobile Broadband typically refers to providing customers with high speed data while on the move. There are several technologies

More information

The Boonton USB Peak Power Sensor, Wi-Fi ac Signals and the ETSI EN Standard

The Boonton USB Peak Power Sensor, Wi-Fi ac Signals and the ETSI EN Standard Application Note The Boonton 55006 USB Peak Power Sensor, Wi-Fi 802.11ac Signals and the ETSI EN 300 328 Standard Stephen Shaw Applications Engineer, Boonton Electronics Abstract This application note

More information

Real-life Applications of ICNIRP Guidelines to Various Human EMF Exposure Issues

Real-life Applications of ICNIRP Guidelines to Various Human EMF Exposure Issues Technical Forum Overview and Latest Development of Standards in Human Exposure to Electromagnetic Fields (EMF) Real-life Applications of ICNIRP Guidelines to Various Human EMF Exposure Issues Dr. Brian

More information

Printed Dipole Antenna

Printed Dipole Antenna Printed Dipole Antenna Reto Zingg Abstract In this project a printed dipole antenna is being designed. Printed dipole antennas are of interest, when an electronic product, which is implemented on a printed

More information

MANUAL FOR RX700 LR and NR

MANUAL FOR RX700 LR and NR MANUAL FOR RX700 LR and NR 2013, November 11 Revision/ updates Date, updates, and person Revision 1.2 03-12-2013, By Patrick M Affected pages, ETC ALL Content Revision/ updates... 1 Preface... 2 Technical

More information

Electromagnetic Field Safety

Electromagnetic Field Safety SAR A Basic Restriction for Electromagnetic Field Safety David Baron, PE Consulting Engineer Electromagnetic Field Safety d.baron@ieee.org NOTE. CENAM is not responsible for the content of this document.

More information

DDX 7000 & 8003. Digital Partial Discharge Detectors FEATURES APPLICATIONS

DDX 7000 & 8003. Digital Partial Discharge Detectors FEATURES APPLICATIONS DDX 7000 & 8003 Digital Partial Discharge Detectors The HAEFELY HIPOTRONICS DDX Digital Partial Discharge Detector offers the high accuracy and flexibility of digital technology, plus the real-time display

More information

Wireless Power Transfer

Wireless Power Transfer Francesco Carobolante Vice President Engineering Wireless Power Transfer Overcoming the Technological Hurdles DISCLAIMER: The information provided in this presentation is for informational purposes only

More information

Application Note Noise Frequently Asked Questions

Application Note Noise Frequently Asked Questions : What is? is a random signal inherent in all physical components. It directly limits the detection and processing of all information. The common form of noise is white Gaussian due to the many random

More information

Radio Frequency Exposure Test Report

Radio Frequency Exposure Test Report Radio Frequency Exposure EN 62311 January 2008 Assessment of electronic and electrical equipment related to human exposure restrictions for electromagnetic fields (0Hz 300GHz) (IEC 62311:2007, modified)

More information

Best Practices Guide for Obvius Data Acquisition Products

Best Practices Guide for Obvius Data Acquisition Products Best Practices Guide for Obvius Data Acquisition Products Part I: Background/general information Obvius LLC provides industry-leading products for cost effective data gathering, storage and communications.

More information

AC3200 INTELLIGENT BROADBAND AMPLIFIER

AC3200 INTELLIGENT BROADBAND AMPLIFIER Kari Mäki 12.11.2009 1(8) AC3200 INTELLIGENT BROADBAND AMPLIFIER AC3200 is the latest leading-edge addition to AC family with extended frequency and gain ranges and integrated electrical controls in both

More information