RAID installation guide for ITE8212F

Size: px
Start display at page:

Download "RAID installation guide for ITE8212F"

Transcription

1 RAID installation guide for ITE8212F

2 Contents Contents 2 1 Introduction About this Guide The Basics What is RAID? Advantages of RAID Disadvantages of RAID Different Types of RAID Configurations RAID 0 (Striping) RAID 1 (Mirroring) RAID 0+1 (Striping/Mirroring) JBOD (Spanning) 4 2 Drivers Creating a Driver Disk Installing Drivers 5 3 Installing Hard Disks 7 4 Creating a RAID Array Configuring BIOS Using the BIOS Configuration Utility Auto Configuration Define RAID Delete RAID Rebuild RAID RAID Card Configuration 16 5 Using your RAID Drive Partitioning and Formatting Under Windows XP Installing an OS on a RAID Drive Installing Windows 2000/XP 17 6 Using Hard Drives as Non-RAID 20 Page 2 of 20

3 1 Introduction 1.1 About this Guide This document provides a brief step-by-step guide for beginners in how to set up a RAID drive using the onboard ITE8212F RAID controller, operating under the Windows XP environment. This guide was designed to only cover the basic operations in setting up RAID. Should this document not cover what you need, please refer to the ITE8212 RAID User s Manual provided on the motherboard s Support CD. 1.2 The Basics What is RAID? A RAID (Redundant Array of Independent Disks) controller lets you combine multiple hard disks to simulate a single drive. The drive created will properties different to that of the individual drives Advantages of RAID The obvious advantage of using a RAID configuration is the ability to create drives with larger capacity. However, since multiple drives are used, data can be stored in such a way that it spans over many disks, thus the information can be accessed by the disks simultaneously, significantly improving data access times Disadvantages of RAID Using many drives has a disadvantage. The probability of a single drive failing out of many drives is much higher than that of one failing out of only one. This results in a greater chance of losing the information on your disks. There are ways however, to minimize this effect, even making it more reliable than using single disks. 1.3 Different Types of RAID Configurations There are many different ways in which RAID can be configured, each with its set of advantages and disadvantages. The ITE8212F controller supports RAID 0, RAID 1, RAID 0+1 and JOBD configurations, each one is described below RAID 0 (Striping) RAID 0 works by breaking down data and spreading it over multiple disk drives. RAID 0 does not protect data from failure, and due to the way it stores data, a fault on one drive would result in failure of the entire array. It does however, have vast improvements in both reading and writing speeds, with the theoretical speed proportional to the number of disks used in the array. It is also fairly efficient in using disk space, with its size is equal to the size of the smallest disk multiplied by the number of disks RAID 1 (Mirroring) RAID 1 works by maintaining an identical copy of the data of one drive on another. If either of these drives should fail, no information is lost as the second drive will always contain an identical copy of the other. A RAID 1 system can be recovered by simply replacing the Page 3 of 20

4 damaged disk and mirroring the data on the new drive. This method should cause a decrease in writing speeds, and results in a disk capacity equivalent to that of the smaller disk RAID 0+1 (Striping/Mirroring) RAID 0+1 combines RAID 0 and RAID 1, creating two arrays of RAID 0, one mirroring the other. This method has both the faster data access speeds of RAID 0 and the data security level of RAID 1. Its disk capacity (in a 4 drive array) is double that of the smallest drive JBOD (Spanning) Standing for Just a Bunch Of Disks, JBOD simply stores data on a drive in an array and moves on onto another in the array when it is full. It creates a drive size equal to the sum of the sizes of all the drives in the array with no performance enhancement. JBOD does not protect data from failure and a fault on one drive will cause the entire array to fail. 2 Drivers A driver is required for your operating system (OS) to recognize your RAID drives. If you are planning to install Windows 2000 or XP on a RAID drive, you will need a copy of the drivers on a floppy disk during installation (refer to 2.1 Creating a Driver Disk). If the RAID drive is to be installed onto a system with an existing OS, please ensure the drivers are correctly installed for your OS to recognize the newly constructed RAID system (refer to 2.2 Installing Drivers). 2.1 Creating a Driver Disk **This will most likely need to be done on a second computer unless you are re-installing your OS onto a RAID drive.** 1) Insert your motherboard s Support CD into your CD-ROM drive. A menu should automatically pop up if Autorun is enabled. 2) Go to My Computer and then your CD-ROM drive to find the folder. Please note that the directory structure may vary between different Support CDs. 3) Run MakeDisk.exe. 4) Insert a floppy into your floppy drive and click on Extract. This will copy the driver files onto the floppy. Page 4 of 20

5 5) When the program finishes copying the files, click on Quit to close the program. 2.2 Installing Drivers The drivers for the ITE8212 IDE RAID controller should be already installed if you have followed your motherboard s manual after installing your OS. However, it is still best to check. 1) Under Windows XP, right click on My Computer and go to properties. 2) Click on the Hardware tab and then click on Device Manager. Page 5 of 20

6 3) Open SCSI and RAID controllers and check if ITE RAID Controller (Windows XP) is there. 4) If it is, then you should be ready to install your RAID drive. If not, follow the remaining steps to install the driver. 5) Insert your motherboard s Support CD into your CD-ROM drive. A menu should automatically pop up if Autorun is enabled. Page 6 of 20

7 6) Click on the Drivers tab and then on ITE8212 Driver and Application. Likewise, if Autorun isn t enabled, run the installer from \Drivers\ITE8212\Driver\ITERAID.exe. 3 Installing Hard Disks The ITE8212 controller supports up to a maximum of 4 hard disks, 2 parallel ATA disks on each of the 2 connectors. For a RAID 0 or JBOD array, a minimum of 2 disks must be used. A RAID 1 array needs two disks while a RAID 0+1 needs four disks. When installing hard disks for a RAID array, it is preferable to use disks that are similar in disk capacity. For best results, please use identical disks. Connect your hard drives, please refer to your motherboard s manual for help if necessary. 4 Creating a RAID Array 4.1 Configuring BIOS Please note that procedures may vary between different motherboards. Check with your motherboard s manual if you have any problems. 1) Power on your computer and go into the BIOS settings by pressing the <Delete> key during the boot sequence. Page 7 of 20

8 2) Enter the Advanced menu by pressing the right arrow key. 3) Browse until you reach the Onboard Devices Configuration and then press <Enter>. 4) Set ITE8212F Controller to RAID Mode. 5) Press <F10> to save your settings and reboot. 4.2 Using the BIOS Configuration Utility The ITE8212 RAID BIOS Setup Utility is used to manage your RAID arrays with this chipset. On that screen it also lists the drives connected to your ITE8212F RAID controller. Enter the Setup Utility by pressing <Ctrl-F> or <Ctrl-E> when it prompts you to during boot. The main menu of the Setup Utility allows you to access the functions used to create and manage your RAID arrays. There are five options in the main menu, please press 1~5 to enter the submenu or the Esc key to quit the Setup Utility. Page 8 of 20

9 4.3 Auto Configuration This function allows you to quickly create a RAID drive using default settings. (Please make you have already back up your data in hard drive before you create arrays) 1) Enter the Setup Utility and select 1 Auto Configuration. 2) Use the arrow keys and and the space key to change the options. 3) There are five configuration options: RAID Type Raid Mode Number of disks required RAID 0 Striping 2 or 3 or 4 RAID 1 Mirroring 2 RAID 0+1 Striping + Mirroring 4 JBOD Span 2 or 3 or 4 IDE None 1 or 2 or 3 or 4 Page 9 of 20

10 4) Press <Ctrl-Y> to save the setting, or Esc key to leave Auto Configuration and go back to the Main Menu. 5) Setting up a new array will cause old data on the disks to disappear. A warning message will appear on the screen. Press <Y> to create the array, or any key to cancel the array creation. 4.4 Define RAID This function allows you to manually create RAID arrays, allowing better flexibility over what was offered when setting up automatically. 1) Enter the Setup Utility and select 2 Define RAID. 2) Use arrow keys and to highlight the Array No you wish to define. Please use the space key to make the array bootable if you would like to boot your system from the array. Press <Enter> to select the highlighted Array No and enter Define RAID submenu to configure the array. Press <Esc> to quit and go back to the Main Menu. Page 10 of 20

11 3) Please use arrow keys and to highlight different configuration position. Use the space key to cycle through the different options. 4) If you have chosen to create a RAID 0 or RAID 0+1 array, you will be given the option of selecting the Block Size. It is recommended to leave this option at its default setting. 5) Drive Assignments displays the information on the hard drives attached to the RAID controller. Use arrow keys and to highlight the drive you wish to assign to the array. Press space key to change the Assignment status to Y. Pri represents the primary channel, and Sec represents the secondary channel. D0 represents the hard drive as Master, and D1 represents the hard drive as Slave. When is displayed in the Size (MB) column, the unit for capacity is GB. 6) Press <Ctrl-Y> to save the configuration. If your settings are correct, a warning message about losing old data will appear. Page 11 of 20

12 7) Press <Y> to erase the data on the hard drive, and to create the array. Press <N> to abort. 8) If the RAID Mode is either Mirror or Strip+Mirror, and you choose not to erase old data, the Rebuild RAID Menu will appear. 9) If you choose not to rebuild the array at this time, a warning message about inconsistent data will appear. Page 12 of 20

13 10) If you press <Y> to rebuild at this time, you will be asked to choose a source disk. Then you will be asked whether you wish to monitor the reconstruction. For details, please refer to 4.6 Rebuild RAID Steps (3) ~ (6) Delete RAID This function allows you to delete RAID arrays. 11) Enter the Setup Utility and select 3 Delete RAID. 12) Use arrow keys and to highlight the array you wish to delete. Press <D> to enter the Delete RAID Submenu. The D key has no effect if the highlighted array is empty. Press <Esc> to go back to the Main Menu. 13) Press <Ctrl-Y> to confirm the deletion, or press any other key to abort. Page 13 of 20

14 14) If you press <Ctrl-Y>, the utility will prompt you asking whether to erase the data on the hard drives. Press <Y> to clear the data, <N> to keep the data on the hard drive. 4.6 Rebuild RAID This function allows you to rebuild a mirrored (RAID 1 or RAID 0+1) array. 1) Enter the Setup Utility and select 4 Rebuild RAID. 2) Use arrow keys and to highlight the array you wish to rebuild. Press <Enter> to enter the Rebuild RAID Drive Select Submenu. Press <Esc> to go back to the Main Menu. Page 14 of 20

15 3) Use arrow keys and to highlight the source disk(s). Press <Enter> to make the selection. When the utility prompts you to continue, press <Y> to continue with rebuilding, or press <ESC> to abort. 4) If you press <Y>, you will be asked whether you wish to monitor the rebuild progress. You can leave the Setup Utility and reboot if you choose background rebuild. If you choose to monitor the reconstruction, you can monitor the progress until it finishes. Page 15 of 20

16 5) When the rebuild is complete, you will be informed. Press any key to go back to the Rebuild RAID Menu 6) If you choose not to monitor the reconstruction, the reconstruction will occur in the background. 4.7 RAID Card Configuration This function allows you to see RAID controller s resources and each hard drive s status 1) Enter the Setup Utility and select 5 RAID Card Configuration. Page 16 of 20

17 2) Use the arrow keys and and the space key to enable or disable Auto-Rebuild option. The Auto-Rebuild function allows automatic rebuild of mirrored array if the failed drive is replaced without powering down your PC. (You must have removable docking cases that support hot-plug to replace hard drive without turning down PC.) When this function is disabled, you need to manually rebuild the array. 3) On the RAID Card Resource section, PCI slot interrupt and I/O port addresses are displayed. On the Drive Status section, each hard drive s status is displayed. 5 Using your RAID Drive Once you created your RAID drive, it will act like any other newly installed disk drive; it will not be partitioned or formatted. You will have to partition and format the drive in order to use it. If you are installing Windows, the setup program will allow you to partition and format the drive during installation. 5.1 Partitioning and Formatting Under Windows XP The Disk Management utility is used to partition and format disks under Windows XP. 1) Right click on My Computer and select manage. 2) Select Disk Management under Storage. For further information on how to use this utility, consult your Windows manual or click on Help. 5.2 Installing an OS on a RAID Drive Installing an operating system on a RAID drive is the same as installing it on a standard drive except that a RAID driver needs to be installed during the installation of the OS Installing Windows 2000/XP 1) Remove any floppy disks from their drives. 2) Insert your Windows installation CD into your CD-ROM drive and restart your computer. Page 17 of 20

18 3) Enter BIOS setup screen, and follow instructions in your user s manual to set your desired optical drive (the one with the Windows installation CD inside) as the first boot device, then save and exit the BIOS setup screen. 4) Press any key in boot from the CD when prompted (in some motherboards, booting from a CD is automatic and no keys are needed to be pressed). 5) Press <F6> when Windows asks if you need to install a third party SCSI or RAID driver. 6) When Windows finishes an examination of your system, you will be asked to specify additional devises or to ignore it. Press <S> to specify your ITE8212F IDE RAID controller. 7) Insert the floppy containing the RAID drivers created in 2.1 Creating a Driver Disk and then press <Enter>. Page 18 of 20

19 8) Select ITE8212 RAID Controller(Windows XP). Please select the correct driver for you OS. Choosing the wrong driver may cause problems. 9) The RAID driver is now loaded, continue the installation of Windows as you normally would. Page 19 of 20

20 6 Using Hard Drives as Non-RAID Drives connected to the ITE8212F RAID controller (RAID Mode in BIOS) do not have to be set up in a RAID array in order for them to work. By simply not assigning them to an array, they can be used like any other drive connected to the board s main IDE connectors. Alternatively, you can set ITE8212F to IDE Mode in the BIOS. Please go to Advanced > Onboard Devices Configuration Menu, set ITE8212F Controller to IDE Mode. If you would like to install OS on the non-raid hard drive connected to the ITE8212F RAID controller, you still need to prepare the driver disk. Please follow the steps in 5.2 Installing an OS on the RAID drive. Page 20 of 20

Table of Contents. Configuring IDE RAID Hard Drive(s) (Controller GigaRAID (IT8212))... 2

Table of Contents. Configuring IDE RAID Hard Drive(s) (Controller GigaRAID (IT8212))... 2 Table of Contents Configuring IDE RAID Hard Drive(s) (Controller GigaRAID (IT8212))... 2 (1) Installing IDE hard drive(s) in your system... 2 (2) Configuring GigaRAID controller mode and boot sequence

More information

RAID installation guide for Silicon Image SiI3114

RAID installation guide for Silicon Image SiI3114 RAID installation guide for Silicon Image SiI3114 Contents Contents 2 1 Introduction 4 1.1 About this Guide 4 1.2 The Basics 4 1.2.1 What is RAID? 4 1.2.2 Advantages of RAID 4 1.2.3 Disadvantages of RAID

More information

Ultra ATA 133 RAID PCI Pro

Ultra ATA 133 RAID PCI Pro Ultra ATA 133 RAID PCI Pro 1-1 Introduction Quick Installation Guide This ultra high-speed dual channel Ultra ATA/133 RAID controller is designed to support RAID 0, 1, 0+1 and JBOD. RAID configurations

More information

Onboard-RAID. Onboard-RAID supports striping (RAID 0), mirroring (RAID 1), striping/mirroring (RAID 0+1), or spanning (JBOD) operation, respectively.

Onboard-RAID. Onboard-RAID supports striping (RAID 0), mirroring (RAID 1), striping/mirroring (RAID 0+1), or spanning (JBOD) operation, respectively. 1. Introduction Onboard-RAID IEI s Onboard-RAID is designed with Promise IDE RAID controller to provide a cost-effective, high performance RAID that adds performance and/or reliability to systems using

More information

ITE RAID Controller USER MANUAL

ITE RAID Controller USER MANUAL ITE RAID Controller USER MANUAL 120410096E1N Copyright Copyright 2004. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system or translated

More information

SATA+Ultra ATA RAID CONTROLLER RC212. User Manual

SATA+Ultra ATA RAID CONTROLLER RC212. User Manual SATA+Ultra ATA RAID CONTROLLER RC212 Contents Feature and benefits Package contents System requirement Magic Switch introduction and jumper setting Hardware installation Important message for user RAID

More information

Guide to SATA Hard Disks Installation and RAID Configuration

Guide to SATA Hard Disks Installation and RAID Configuration Guide to SATA Hard Disks Installation and RAID Configuration 1. Guide to SATA Hard Disks Installation... 2 1.1 Serial ATA (SATA) Hard Disks Installation... 2 2. Guide to RAID Configurations... 3 2.1 Introduction

More information

www.devicemanuals.eu

www.devicemanuals.eu AMD RAID Introduction The integrate one SATA host controller separately, and support RAID function for performance and reliability. SB950 SATA RAID provides support for RAID 0 (Striping), RAID 1 (Mirroring),

More information

NVIDIA RAID Installation Guide

NVIDIA RAID Installation Guide NVIDIA RAID Installation Guide 1. NVIDIA BIOS RAID Installation Guide.. 2 1.1 Introduction to RAID. 2 1.2 RAID Configurations Precautions.. 3 1.3 Create Disk Array. 4 2. NVIDIA Windows RAID Installation

More information

SATA1.5G/ATA133 RAID Controller Card RC215 User Manual

SATA1.5G/ATA133 RAID Controller Card RC215 User Manual SATA1.5G/ATA133 RAID Controller Card RC215 Features and Benefits Compliant with Serial ATA 1.0 specification Compliant with PCI Specification, revision 2.2 Provides three independent channels to connect

More information

VT8237 SATA RAID User Manual

VT8237 SATA RAID User Manual VT8237 SATA RAID User Manual Enter BIOS Configuration Utility When the system powers on, the following information will appear on screen. Press the Tab key to enter BIOS configuration utility. 39 VIA Technologies,Inc.VIA

More information

VIA / JMicron RAID Installation Guide

VIA / JMicron RAID Installation Guide VIA / JMicron RAID Installation Guide 1. Introduction to VIA / JMicron RAID Installation Guide. 3 2. VIA RAID Installation Guide. 3 2.1 VIA BIOS RAID Installation Guide.. 3 2.1.1 Introduction of RAID.

More information

Promise FastTrak 100-Lite RAID Controller

Promise FastTrak 100-Lite RAID Controller Promise FastTrak 100-Lite RAID Controller User s Manual Version 1.3, November 9, 2001 Copyright Copyright by Promise Technology, Inc. ( Promise ), XP. No part of this manual may be reproduced or transmitted

More information

RAID Manual. Edition. Trademarks V1.0 P/N: 91-187-CK8-A5-0E

RAID Manual. Edition. Trademarks V1.0 P/N: 91-187-CK8-A5-0E RAID Manual Edition V1.0 P/N: 91-187-CK8-A5-0E Trademarks All brand or product names mentioned are trademarks or registered trademarks of their respective holders. Contents NVIDIA RAID... 1 RAID Arrays...

More information

AMD RAID Installation Guide

AMD RAID Installation Guide AMD RAID Installation Guide 1. AMD BIOS RAID Installation Guide.. 2 1.1 Introduction to RAID.. 2 1.2 RAID Configurations Precautions 3 1.3 Installing Windows XP / XP 64-bit / Vista / Vista 64-bit With

More information

AMD RAID Installation Guide

AMD RAID Installation Guide AMD RAID Installation Guide 1. AMD BIOS RAID Installation Guide.. 2 1.1 Introduction to RAID.. 2 1.2 RAID Configurations Precautions 3 1.3 Installing Windows 7 / 7 64-bit / Vista / Vista 64-bit / XP /

More information

VIA RAID configurations

VIA RAID configurations VIA RAID configurations The motherboard includes a high performance IDE RAID controller integrated in the VIA VT8237R southbridge chipset. It supports RAID 0, RAID 1 and JBOD with two independent Serial

More information

M5281/M5283. Serial ATA and Parallel ATA Host Controller. RAID BIOS/Driver/Utility Manual

M5281/M5283. Serial ATA and Parallel ATA Host Controller. RAID BIOS/Driver/Utility Manual Serial ATA and Parallel ATA Host Controller Rev. 0.96 December 03, 2003 Copyright 2003 ULi Electronics Inc. All rights reserved. COPYRIGHT NOTICE All information in this document is considered ULi Electronics

More information

RAID User Guide. Edition. Trademarks V1.0 P/N: 91-187C51GME0-00

RAID User Guide. Edition. Trademarks V1.0 P/N: 91-187C51GME0-00 RAID User Guide Edition V1.0 P/N: 91-187C51GME0-00 Trademarks All brand or product names mentioned are trademarks or registered trademarks of their respective holders. Contents NVIDIA RAID...1 RAID Arrays...1

More information

SiS 180 S-ATA User s Manual. Quick User s Guide. Version 0.1

SiS 180 S-ATA User s Manual. Quick User s Guide. Version 0.1 SiS 180 S-ATA User s Manual Quick User s Guide Version 0.1 Edition April 2003 Copyright Trademarks SiS is a registered trademark of Silicon Integrated Systems Corp. All brand or product names mentioned

More information

Guide to SATA Hard Disks Installation and RAID Configuration

Guide to SATA Hard Disks Installation and RAID Configuration Guide to SATA Hard Disks Installation and RAID Configuration 1. Guide to SATA Hard Disks Installation... 2 1.1 Serial ATA (SATA) Hard Disks Installation... 2 2. Guide to RAID Configurations... 3 2.1 Introduction

More information

SATA RAID Function (Only for chipset Sil3132 used) User s Manual

SATA RAID Function (Only for chipset Sil3132 used) User s Manual SATA RAID Function (Only for chipset Sil3132 used) User s Manual 12ME-SI3132-001 Table of Contents 1 WELCOME...4 1.1 SATARAID5 FEATURES...4 2 AN INTRODUCTION TO RAID...5 2.1 DISK STRIPING (RAID 0)...5

More information

SATA II 4 Port PCI RAID Card RC217 User Manual

SATA II 4 Port PCI RAID Card RC217 User Manual SATA II 4 Port PCI RAID Card RC217 SATA II 4 Port PCI RAID Card This Manual is for many Models of SATAII RAID5 HBA that uses Silicon Image SATA II SiI3124 chipset: 1) 32bit PCI bus host card 2) 64bit PCI-X

More information

English. Configuring SATA Hard Drive(s)

English. Configuring SATA Hard Drive(s) Configuring SATA Hard Drive(s) To configure SATA hard drive(s), follow the steps below: (1) Install SATA hard drive(s) in your system. (2) Configure SATA controller mode and boot sequence in BIOS Setup.

More information

Intel ESB2 SATA RAID Setup Guidelines

Intel ESB2 SATA RAID Setup Guidelines Intel ESB2 SATA RAID Setup Guidelines Intel ESB2 SATA RAID Setup Guidelines After all the hardware has been installed, you must first configure Intel ESB2 SATA RAID Settings before you install the Windows

More information

SiS964 RAID. User s Manual. Edition. Trademarks V1.0 P/N: 91-187-U49-M2-0E

SiS964 RAID. User s Manual. Edition. Trademarks V1.0 P/N: 91-187-U49-M2-0E SiS964 RAID User s Manual Edition V1.0 P/N: 91-187-U49-M2-0E Trademarks All brand or product names mentioned are trademarks or registered trademarks of their respective holders. CONTENTS Introduction...

More information

Guide to SATA Hard Disks Installation and RAID Configuration

Guide to SATA Hard Disks Installation and RAID Configuration Guide to SATA Hard Disks Installation and RAID Configuration 1. Guide to SATA Hard Disks Installation...2 1.1 Serial ATA (SATA) Hard Disks Installation...2 2. Guide to RAID Configurations...3 2.1 Introduction

More information

Serial ATA RAID PCI. User's Manual

Serial ATA RAID PCI. User's Manual Serial ATA RAID PCI User's Manual Chapter 1 Introduction Table of Contents 1-1 Features and Benefits. 1 1-2 System Requirements. 1 Chapter 2 RAID Arrays 2-1 RAID Overview.. 2 2-1.1 RAID 0 (striping)...

More information

SiS964/SiS180 SATA w/ RAID User s Manual. Quick User s Guide. Version 0.3

SiS964/SiS180 SATA w/ RAID User s Manual. Quick User s Guide. Version 0.3 SiS964/SiS180 SATA w/ RAID User s Manual Quick User s Guide Version 0.3 Edition December 2003 Copyright 2003 Silicon Integrated Systems Corp. Trademarks SiS is a registered trademark of Silicon Integrated

More information

SiS964/SiS180 SATA w/ RAID User s Manual. Quick User s Guide. Version 0.3

SiS964/SiS180 SATA w/ RAID User s Manual. Quick User s Guide. Version 0.3 SiS964/SiS180 SATA w/ RAID User s Manual Quick User s Guide Version 0.3 Edition December 2003 Copyright 2003 Silicon Integrated Systems Corp. Trademarks SiS is a registered trademark of Silicon Integrated

More information

AMD RAID Installation Guide

AMD RAID Installation Guide AMD RAID Installation Guide 1. AMD BIOS RAID Installation Guide.. 2 1.1 Introduction to RAID.. 2 1.2 RAID Configurations Precautions 3 1.3 Installing Windows 8 / 8 64-bit / 7 / 7 64-bit / Vista TM / Vista

More information

RAID configuration and driver installation guide

RAID configuration and driver installation guide Server systems and motherboards RAID configuration and driver installation guide For AP130-E1 5U Rackmount Server AP1720-E2 5U Rackmount Server NCCH-DL Motherboard PSCH-L Motherboard E1600 First edition

More information

PCI ATA 133 RAID Controller Card. User Manual

PCI ATA 133 RAID Controller Card. User Manual PCI ATA 133 RAID Controller Card User Manual Features and Benefits Silicon Image SiI 0680 Compliant with UltraDMA6 ATA/133 specifications Compliant with PCI v2.2 Plug-n-Play Provides two independent Ultra

More information

SiS S-ATA User s Manual. Quick User s Guide. Version 0.1

SiS S-ATA User s Manual. Quick User s Guide. Version 0.1 SiS S-ATA User s Manual Quick User s Guide Version 0.1 Edition April 2003 Copyright Trademarks SiS is a registered trademark of Silicon Integrated Systems Corp. All brand or product names mentioned are

More information

Configuring ThinkServer RAID 100 on the TS140 and TS440

Configuring ThinkServer RAID 100 on the TS140 and TS440 Configuring ThinkServer RAID 100 on the TS140 and TS440 Lenovo ThinkServer TS Series Servers Lenovo Enterprise Product Group Version 1.0 September 17, 2013 2013 Lenovo. All rights reserved. LENOVO PROVIDES

More information

To configure SATA hard drive(s), follow the steps below:

To configure SATA hard drive(s), follow the steps below: 4-1-4 Configuring SATA Hard Drive(s) To configure SATA hard drive(s), follow the steps below: (1) Install SATA hard drive(s) in your system. (2) Configure SATA controller mode and boot sequence in BIOS

More information

GigaRAID (IT8212) ATA RAID Controller USER S MANUAL

GigaRAID (IT8212) ATA RAID Controller USER S MANUAL GigaRAID (IT8212) ATA RAID Controller USER S MANUAL 12ME-IT8212-006R Copyright Copyright by GIGA-BYTE TECHNOLOGY CO., LTD. ( GBT ) No part of this manual may be reproduced or transmitted in any from without

More information

RAID Option Installation

RAID Option Installation RAID Option Installation Introduction RAID option is a PCI board including two HDD. The RAID option installation is carried out in 4 main phases: Pase A: Hardware installation Phase B: Configuration of

More information

Intel Matrix Storage Manager 8.x

Intel Matrix Storage Manager 8.x Intel Matrix Storage Manager 8.x User's Manual January 2009 Revision 1.0 Document Number: XXXXXX INFORMATION IN THIS DOCUMENT IS PROVIDED IN CONNECTION WITH INTEL PRODUCTS. NO LICENSE, EXPRESS OR IMPLIED,

More information

Encore SATA2 RAID PCIe Card

Encore SATA2 RAID PCIe Card Encore SATA2 RAID PCIe Card User Manual Ver. 2.00 All brand names and trademarks are properties of their Respective owners. 1 Features and Benefits Compliant with PCI Express Base Specification 1.0a Compliant

More information

VIA RAID Installation Guide

VIA RAID Installation Guide VIA RAID Installation Guide 1 VIA BIOS RAID Installation Guide.... 3 1.1 Introduction of RAID... 3 1.2 RAID Configuration Precautions... 3 1.3 BIOS Configuration Utility.. 4 1.3.1 Enter BIOS Configuration

More information

VIA RAID Installation Guide

VIA RAID Installation Guide VIA RAID Installation Guide 1 VIA BIOS RAID Installation Guide.... 3 1.1 Introduction of RAID... 3 1.2 RAID Configuration Precautions... 3 1.3 Installing Windows 2000 / XP / Vista With RAID Functions..

More information

Serial ATA RAID PCI Card

Serial ATA RAID PCI Card Serial ATA RAID PCI Card User Manual 1 Features Silicon Image SiI3512 SATA controller chip Compliant with PCI Specification, Rev. 2.3 Compliant with Serial ATA 1.0 specification Provides two independent

More information

HP dx5150 RAID Installation and Setup Guide Version 1.10. Document Part Number: 403571-001

HP dx5150 RAID Installation and Setup Guide Version 1.10. Document Part Number: 403571-001 HP dx5150 RAID Installation and Setup Guide Version 1.10 Document Part Number: 403571-001 July 2005 Copyright 2005 Hewlett-Packard Development Company, L.P. The information contained herein is subject

More information

HPT370 UltraDMA-100 & RAID Setup Guide For EP-BX7+100 RAID Introduction The HPT370 ROM BIOS provides a built-in setup program which allows the user to modify, create, or delete arrays. RAID stands for

More information

Intel ICH7R/ICH9R/ICH10R HostRAID Setup Guidelines

Intel ICH7R/ICH9R/ICH10R HostRAID Setup Guidelines Intel ICH7R/ICH9R/ICH10R HostRAID Setup Guidelines Intel ICH7R/ICH9R/ICH10R HostRAID Setup Guidelines After all hardware has been installed, you must fi rst confi gure the Intel SATA HostRAID settings

More information

Low Profile Ultra ATA-133 RAID PCI Host

Low Profile Ultra ATA-133 RAID PCI Host Low Profile Ultra ATA-133 RAID PCI Host User Manual English LINDY No. 70642 www.lindy.com LINDY ELECTRONICS LIMITED & LINDY-ELEKTRONIK GMBH - FIRST EDITION (November 2004) 1. Introduction This Low Profile

More information

ESATA PCI CARD. User s Manual

ESATA PCI CARD. User s Manual ESATA PCI CARD User s Manual Introduction... 3 System Requirements... 3 RAID Introduction... 3 BIOS Configuration Utility... 5 Configuring Arrays... 5 RAID Mode Definitions... 5 BIOS Configuration Utility...

More information

Promise RAID Function

Promise RAID Function Promise RAID Function (Only For Chipset 20265/20276 Used) USER S MANUAL 12ME-RAI276-001 RAID Function Copyright Copyright by GIGA-BYTE TECHNOLOGY CO., LTD. ( GBT ) No part of this manual may be reproduced

More information

PCI SATA + PATA Raid Card

PCI SATA + PATA Raid Card PCI SATA + PATA Raid Card User Manual Ver. 5.00 All brand names and trademarks are properties of their Respective owners. Features and Benefits Compliant with Serial ATA 1.0 specification Compliant with

More information

Guide to SATA Hard Disks Installation and RAID Configuration

Guide to SATA Hard Disks Installation and RAID Configuration Guide to SATA Hard Disks Installation and RAID Configuration 1. Guide to SATA Hard Disks Installation...2 1.1 Serial ATA (SATA) Hard Disks Installation...2 2. Guide to RAID Confi gurations...3 2.1 Introduction

More information

Intel Rapid Storage Technology

Intel Rapid Storage Technology Intel Rapid Storage Technology User Guide August 2011 Revision 1.0 1 Document Number: XXXXXX INFORMATION IN THIS DOCUMENT IS PROVIDED IN CONNECTION WITH INTEL PRODUCTS. NO LICENSE, EXPRESS OR IMPLIED,

More information

RAID installation guide

RAID installation guide RAID installation guide V1.0 Date : 2009-06-29 TWINHEAD INTERNATIONAL CORP. 10F, 550 Rueiguang Road Neihu, Taipei, Taiwan 114,ROC. TEL(886)2 5589 9999 FAX (886) 2 5555 7777 Enabling RAID in BIOS Perform

More information

Serial ATA 4-Channel RAID Quick Installation Guide

Serial ATA 4-Channel RAID Quick Installation Guide Serial ATA 4-Channel RAID Quick Installation Guide Introducing the Serial ATA 4-Channel RAID The Serial ATA 4-Channel RAID is an ultra high-speed four channel Serial ATA controller for use in Pentium class

More information

Addonics. 4-Port External SATA II PCI/PCI-X RAID5 Controller Card (ADS3GX4R5-E) User s Guide Revision 1.1 T E C H N O L O G I E S

Addonics. 4-Port External SATA II PCI/PCI-X RAID5 Controller Card (ADS3GX4R5-E) User s Guide Revision 1.1 T E C H N O L O G I E S Addonics T E C H N O L O G I E S 4-Port External SATA II PCI/PCI-X RAID5 Controller Card (ADS3GX4R5-E) User s Guide Revision 1.1 FCC Warning Statement This equipment has been tested and found to comply

More information

Configuring ThinkServer RAID 100 on the Lenovo TS130

Configuring ThinkServer RAID 100 on the Lenovo TS130 Configuring ThinkServer RAID 100 on the Lenovo TS130 Contents Overview 02 Embedded RAID 100 features on TS130 02 RAID Overview 02 Choosing the RAID Level 02 RAID 0 02 RAID 1 03 Configuring RAID 03 BIOS

More information

6-Port SATA II 150 PCI Host Card w/raid

6-Port SATA II 150 PCI Host Card w/raid 6-Port SATA II 150 PCI Host Card w/raid User Manual Model: UGT-ST310R All brand names and trademarks are properties of their respective owners. w w w. v a n t e c u s a. c o m Table of Contents 1. Bus

More information

Guide to SATA Hard Disks Installation and RAID Configuration

Guide to SATA Hard Disks Installation and RAID Configuration Guide to SATA Hard Disks Installation and RAID Configuration 1. Guide to SATA Hard Disks Installation..2 1.1 Serial ATA (SATA) Hard Disks Installation 2 1.2 Making An SATA Driver Diskette 3 2. Guide to

More information

EX-3516 4-Port SATA3 RAID/HyperDuo PCIe(x2) Card

EX-3516 4-Port SATA3 RAID/HyperDuo PCIe(x2) Card EX-3516 4-Port SATA3 RAID/HyperDuo PCIe(x2) Card Thank you for purchasing this 4-Port SATA3 RAID/HyperDuo PCIe Card. It is designed to support up to 4 SATA3 ports in RAID 0 and RAID 1, RAID 0+1 modes and

More information

Adaptec SAS RAID Configuration and the Windows OS Installation Instructions

Adaptec SAS RAID Configuration and the Windows OS Installation Instructions Adaptec SAS RAID Confi guration and the Windows OS Installation Instructions Adaptec SAS RAID Configuration and the Windows OS Installation Instructions After all the hardware has been installed, you must

More information

IDE2410 ATA-100 IDE RAID Card. Version 1.0

IDE2410 ATA-100 IDE RAID Card. Version 1.0 IDE2410 ATA-100 IDE RAID Card Version 1.0 Contents 1.0 Features....P.3 2.0 System Requirement.P.3 3.0 Installing the ATA/100 IDE Controller Card P.4 4.0 Driver Installation..P.4 5.0 RAID Explained.P.7

More information

SATARAID5 Serial ATA RAID5 Management Software. Users Manual

SATARAID5 Serial ATA RAID5 Management Software. Users Manual SATARAID5 Serial ATA RAID5 Management Software Home Edition Users Manual 03/14/05 Silicon Image, Inc. 1060 East Arques Ave. Sunnyvale CA 94085 (408) 616-4000 www.siliconimage.com Copyright 2004, Silicon

More information

Table of Contents. Configuring SATA Hard Drive(s) (Controller SiS 964)... 2. (2) Configuring SATA controller mode and boot sequence in BIOS Setup...

Table of Contents. Configuring SATA Hard Drive(s) (Controller SiS 964)... 2. (2) Configuring SATA controller mode and boot sequence in BIOS Setup... Table of Contents Configuring SATA Hard Drive(s) (Controller SiS 964)... 2 (1) Installing SATA hard drive(s) in your computer... 2 (2) Configuring SATA controller mode and boot sequence in BIOS Setup...

More information

RocketRAID 1640. User's Manual. Revision: 1.0 Date: Mar. 2003 HighPoint Technologies, Inc.

RocketRAID 1640. User's Manual. Revision: 1.0 Date: Mar. 2003 HighPoint Technologies, Inc. RocketRAID 1640 User's Manual Revision: 1.0 Date: Mar. 2003 HighPoint Technologies, Inc. Copyright Copyright 2003 HighPoint Technologies, Inc.. This document contains materials protected by International

More information

SATARAID5 Serial ATA RAID5 Management Software

SATARAID5 Serial ATA RAID5 Management Software SATARAID5 Serial ATA RAID5 Management Software Home Edition Preliminary Draft Subject to Change Without Notice 05/7/04 Silicon Image, Inc. 1060 East Arques Ave. Sunnyvale CA 94085 (408) 616-4000 www.siliconimage.com

More information

LSI Software RAID Configuration Utility

LSI Software RAID Configuration Utility LSI Software RAID Configuration Utility E8581 First Edition August 2013 Copyright 2013 ASUSTeK COMPUTER INC. All Rights Reserved. No part of this manual, including the products and software described in

More information

SATA 150 RAID. user. Model 176767 MAN-176767-UM-1007-01

SATA 150 RAID. user. Model 176767 MAN-176767-UM-1007-01 SATA 150 RAID Controller PCI Card user manual Model 176767 MAN-176767-UM-1007-01 introduction Thank you for purchasing this MANHATTAN SATA 150 RAID Controller PCI Card, Model 176767. The easy-to-follow

More information

46xx_47xx_1546_1547 RAID Recovery/Set Up Instructions

46xx_47xx_1546_1547 RAID Recovery/Set Up Instructions 46xx_47xx_1546_1547 RAID Recovery/Set Up Instructions Note: The Windows RAID utility should handle most RAID recovery situations without any trouble. In Windows, when the ICON in the RAID utility turns

More information

Promise RAID MBFastTrak133 TM Lite. User s Manual

Promise RAID MBFastTrak133 TM Lite. User s Manual Promise RAID MBFastTrak133 TM Lite User s Manual Copyright Copyright 2002 by Albatron. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval

More information

The SATA II PCIe RAID is an ultra high-speed two channel Serial ATA Generation II RAID controller for use in PCI Express enabled systems.

The SATA II PCIe RAID is an ultra high-speed two channel Serial ATA Generation II RAID controller for use in PCI Express enabled systems. SATA II PCIe RAID Quick Installation Guide Introducing the SATA II PCIe RAID The SATA II PCIe RAID is an ultra high-speed two channel Serial ATA Generation II RAID controller for use in PCI Express enabled

More information

Guide to SATA Hard Disks Installation and RAID Configuration

Guide to SATA Hard Disks Installation and RAID Configuration Guide to SATA Hard Disks Installation and RAID Configuration 1. Guide to SATA Hard Disks Installation...2 1.1 Serial ATA (SATA) Hard Disks Installation...2 2. Guide to RAID Configurations...3 2.1 Introduction

More information

ForceWare Software NVIDIA RAID User s Guide. Version 2.0 A

ForceWare Software NVIDIA RAID User s Guide. Version 2.0 A ForceWare Software NVIDIA RAID User s Guide Version 2.0 A NVIDIA Corporation September 3, 2004 NVIDIA Applications NVIDIA RAID User s Guide Version 2.0 Published by NVIDIA Corporation 2701 San Tomas Expressway

More information

Using ATI Array Management Software (WebPAM)

Using ATI Array Management Software (WebPAM) Redundant Array of Independent Disks (RAID) on HP Compaq dc5750 Business PCs Using ATI Array Management Software (WebPAM) Introduction............................................................ 2 Mirroring

More information

Table of Contents 1. INTRODUCTION TO THE DC-200 RAID CARD... 3

Table of Contents 1. INTRODUCTION TO THE DC-200 RAID CARD... 3 Table of Contents 1. INTRODUCTION TO THE DC-200 RAID CARD... 3 1.1 UNDERSTANDING RAID CONCEPTS... 3 1.2 OVERVIEW OF DC-200 RAID CARD... 3 1.2.1 Features and specifications of the DC-200 RAID card... 5

More information

Serial ATA 2 Ports PCI Host

Serial ATA 2 Ports PCI Host Serial ATA 2 Ports PCI Host This Manual is for the various Model of 2ports SATA HBA: Model A: Low Profile Serial ATA Internal 2 Ports Model B: Low Profile External 1 Port + Internal 1 Port Model C: Low

More information

Offline Array Recovery Procedures SuperTrak SX6000 and UltraTrak

Offline Array Recovery Procedures SuperTrak SX6000 and UltraTrak Version 5a Offline Array Recovery Procedures SuperTrak SX6000 and UltraTrak This document describes the procedures for protecting data and restoring array status to arrays that have gone OFFLINE. Promise

More information

4+1 SATA II 300 IDE/PATA PCI-E. Combo Host Card w/ RAID & Port. Multiplier

4+1 SATA II 300 IDE/PATA PCI-E. Combo Host Card w/ RAID & Port. Multiplier 4+1 SATA II 300 IDE/PATA PCI-E Combo Host Card w/ RAID & Port Multiplier User Manual Model: UGT-IS100R All brand names and trademarks are properties of their respective owners. w w w. v a n t e c u s a.

More information

Chapter 2 Array Configuration [SATA Setup Utility] This chapter explains array configurations using this array controller.

Chapter 2 Array Configuration [SATA Setup Utility] This chapter explains array configurations using this array controller. Embedded MegaRAID SATA User's Guide Areas Covered Before Reading This Manual This section explains the notes for your safety and conventions used in this manual. Chapter 1 Overview This chapter introduces

More information

HP User Manual for LSI Integrated RAID on HP xw4200/xw6200/xw8200/xw9300 Workstation

HP User Manual for LSI Integrated RAID on HP xw4200/xw6200/xw8200/xw9300 Workstation HP User Manual for LSI Integrated RAID on HP xw4200/xw6200/xw8200/xw9300 Workstation LSI Integrated RAID controller and Host Bus Adapter... 2 Steps common to all methods for enabling LSI Integrated RAID...

More information

ATA-133 IDE RAID Card. Version 1.1

ATA-133 IDE RAID Card. Version 1.1 ATA-133 IDE RAID Card Version 1.1 Contents 1.0 Features....P.3 2.0 Package Content....P.3 3.0 System Requirement.P.3 4.0 Installing the ATA/133 IDE Controller Card P.4 5.0 Driver Installation..P.5 6.0

More information

Serial-ATA IDE Card. Version 1.0

Serial-ATA IDE Card. Version 1.0 Serial-ATA IDE Card Version 1.0 Contents 1.0 Features....P.3 2.0 System Requirement.P.3 3.0 Driver Installation..P.4 Windows NT4.0 / 2000 / XP Fresh Installation.. P4 Windows 98SE / ME Fresh Installation.

More information

About RAID. RAID for performance. How it increases performance. How it makes file storage cheaper. Drawbacks

About RAID. RAID for performance. How it increases performance. How it makes file storage cheaper. Drawbacks www.gateway.com About RAID About RAID RAID (Redundant Array of Inexpensive/Independent Disks) lets your computer use multiple hard drives more efficiently. Your computer supports RAID 0, RAID 1, RAID 5,

More information

RAID OPTION ROM USER MANUAL. Version 1.6

RAID OPTION ROM USER MANUAL. Version 1.6 RAID OPTION ROM USER MANUAL Version 1.6 RAID Option ROM User Manual Copyright 2008 Advanced Micro Devices, Inc. All Rights Reserved. Copyright by Advanced Micro Devices, Inc. (AMD). No part of this manual

More information

ForceWare Software MediaShield User s Guide. Version 5.0

ForceWare Software MediaShield User s Guide. Version 5.0 ForceWare Software MediaShield User s Guide Version 5.0 NVIDIA Corporation May 1, 2006 NVIDIA Applications MediaShield User s Guide Version 5.0 Published by NVIDIA Corporation 2701 San Tomas Expressway

More information

Installation Guide. RAID 5 esata 3Gbps 2 external port Low profi le PCI Express card. GICe702S3R5W6 PART NO. M0557

Installation Guide. RAID 5 esata 3Gbps 2 external port Low profi le PCI Express card. GICe702S3R5W6 PART NO. M0557 Installation Guide RAID 5 esata 3Gbps 2 external port Low profi le PCI Express card 1 GICe702S3R5W6 PART NO. M0557 Table of Contents Caution 4 Introduction 6 Features 7 Package Contents 8 What Is RAID?

More information

SERIAL ATA HOST CONTROLLER CARD USER MANUAL SATA3112-150R SATA3112-150I WARNING

SERIAL ATA HOST CONTROLLER CARD USER MANUAL SATA3112-150R SATA3112-150I WARNING SD-SIL3112-041103 SERIAL ATA HOST CONTROLLER CARD USER MANUAL SATA3112-150R SATA3112-150I WARNING Before installing and activating RAID function, please make sure you have a complete backup of your existing

More information

Advanced Host Controller Interface (AHCI) and Redundant Array of Independent Disks (RAID) on HP Compaq dc5850 Business PCs

Advanced Host Controller Interface (AHCI) and Redundant Array of Independent Disks (RAID) on HP Compaq dc5850 Business PCs Advanced Host Controller Interface (AHCI) and Redundant Array of Independent Disks (RAID) on HP Compaq dc5850 Business PCs Using AMD Array Management Software (RAIDXpert) Introduction............................................................2

More information

FASTTRAK USER MANUAL TX2200, TX2300. Version 3.2

FASTTRAK USER MANUAL TX2200, TX2300. Version 3.2 FASTTRAK TX2200, TX2300 USER MANUAL Version 3.2 FastTrak TX2200, TX2300 User Manual Copyright 2007 Promise Technology, Inc. All Rights Reserved. Copyright by Promise Technology, Inc. (Promise Technology).

More information

PCI SATA Controller Card Model: SY-PCI40010

PCI SATA Controller Card Model: SY-PCI40010 SY-PCI40010 1 PCI SATA Controller Card Model: SY-PCI40010 User Manual Ver. 2.00 Chipset: Silicon Image SIL3124 SY-PCI40010 2 Product Introduction The Silicon Image Sil3124 Serial ATA I/II to PCI-X32/64-bit

More information

RAID Utility for Windows

RAID Utility for Windows RAID Utility for Windows 1. Enter NVRAIDMAN RAID driver is built in nvidia ALL in one driver provided in our support CD. After you finish the driver installation, you can create, delete, or rebuild any

More information

SATA II-150 PCI RAID

SATA II-150 PCI RAID SATA II-150 PCI RAID Quick Installation Guide Introducing the SATA II-150 PCI RAID The SATA II-150 PCI RAID is an ultra high-speed two channel Serial ATA Generation II RAID controller for use in PCI enabled

More information

4 Channel 6-Port SATA 6Gb/s PCIe RAID Host Card

4 Channel 6-Port SATA 6Gb/s PCIe RAID Host Card 4 Channel 6-Port SATA 6Gb/s PCIe RAID Host Card User Manual Model: UGT-ST644R All brand names and trademarks are properties of their respective owners www.vantecusa.com Contents: Chapter 1: Introduction...

More information

RocketRAID 1820. User, s Manual. Revision: 1.0 Date: Sept. 2003 HighPoint Technologies, Inc.

RocketRAID 1820. User, s Manual. Revision: 1.0 Date: Sept. 2003 HighPoint Technologies, Inc. RocketRAID 1820 User, s Manual Revision: 1.0 Date: Sept. 2003 HighPoint Technologies, Inc. Notice Reasonable effort has been made to ensure that the information in this manual is accurate. HighPoint assumes

More information

Serial ATA ( ULi M1573)... 2

Serial ATA ( ULi M1573)... 2 Serial ATA ( ULi M1573)... 2 (1) SATA... 2 (2) BIOS SATA... 3 (3) RAID BIOS RAID... 5 (4) SATA... 13 (5) SATA... 15 Serial ATA ( ULi M1573) SATA (1) SATA (2) BIOS SATA (3)* RAID BIOS RAID (4) SATA (5)

More information

The motherboard supports the following SATA RAID solutions:

The motherboard supports the following SATA RAID solutions: Setting up RAID The motherboard supports the following SATA RAID solutions: LSI MegaRAID software RAID Configuration Utility with RAID 0, RAID 1, and RAID 10 support (for both Linux and Windows OS). Intel

More information

SATA II PCIe RAID Quick Installation Guide

SATA II PCIe RAID Quick Installation Guide SATA II PCIe RAID Quick Installation Guide Introducing the SATA II PCIe RAID The SATA II PCIe RAID is an ultra high-speed two channel Serial ATA Generation II RAID controller for use in PCI Express enabled

More information

SATA II PCIe RAID Quick Installation Guide

SATA II PCIe RAID Quick Installation Guide SATA II PCIe RAID Quick Installation Guide Introducing the SATA II PCIe RAID The SATA II PCIe RAID is an ultra high-speed two channel Serial ATA Generation II RAID controller for use in PCI Express enabled

More information

esata 3.0Gbps RAID ExpressCard

esata 3.0Gbps RAID ExpressCard esata 3.0Gbps RAID ExpressCard 1. Introduction Quick Installation Guide The esata 3.0Gbps 2-channel RAID ExpressCard provides two ultra high-speed esata channels with RAID 0/1 features into your notebook

More information