Heller Industries Inc.

Transcription

1 Software ECN # Change/Update Description Version /29/ Continuation from (XP) version - Added 1914 (14 zone) model - Overview screen resolution changed to 1024 by Updated SECS/GEM capability - Added Lot tracking via SECS/GEM feature - Added Monitoring temperature feature using 2nd HC2 controller (serial communication to main HC2 ctrl). Monitoring HC2 driver version Added feature for Blower RPM data read via SECS/GEM - Added Belt speed range auto switch digital output option - Added Custom digital switch option - Removed default labels from I/O selection; only I/O numbers are displayed /6/ Added HellerSECSGEM version compatibility - VID is usdated using UpdateU1VID, it was I4 type earlier /10/2008 Not released - Recipe shadowing to allow recipe upload/download/delete when it is running (Heller SECSGEM) - Update setup wizard XML file to add channel table. - Update HC2 drivers to allow Offset entry program to work on newer build HC2 (with rev2 of Cirrus logic processor) Rev-A ECN Fixed a crash with Edit mode - Update HC2 drivers to allow voltage style inputs on TDM for belt - Fixed a rare issue related to TDM channel type read. This is related to K-type or voltage style i/p. J-type T/C was never implemented. - Coupter control rail fix for 3 rail 2 conveyor belt configuration Jan Added Smema9851 interface option which addresses smema upstream signal. Upstream stays ready when product entering the oven until board length + board spacing is achieved, then signal goes to not-ready for 0.5sec and comes back to ready state to accept next board Feb Fixed an issue where Smema(II or 9851) options were not getting set to the HC2 controller. This issue was noticed on a Vista OS and version. - Fixed a rare issue where hot job was not getting loaded from a cooldown mode. As soon as recipe loaded oven was going into cooldown.

2 Mar Added Smema with Belt Stop option (Cure Oven SMEMA) - When Belt SP=0, light tower stays Yellow Mar Fixed issues noticed related to board spacing and SMEMA9851 with belt stop Apr Added settable belt stop delay for cure oven smema - Added option: new board delay for SMEMA Added option: Entrance board Jam/Stop warning using predefined board length - Added option to disable board length from board drop calculation Apr Fixed an issue noticed on for board drop not working under certain condition (while board is entering if exit sensor is blocked). - Board entrance and exit Stop are made independent of animation /brd count when predefined board length is selected. - Heat channel PB=15 as a new default value; old value was Added a function for KIC to check if oven is in Remote or Local control June Continuation from Fixed: in if SMEMA9851 is enabled without board animation, then entrance and exit part of smema did not work. - Oven Barcode Program compatibility - VIP mode option for Samsung. Create vip or vip.txt file in c:\oven folder and then run oven program to activate VIP mode - Feature added: Auto log down to operator level - Feature added: Auto acknowledge warning when click OK on pop up message July Bug fixed: auto log down to operate mode: once log down to operate mode, SP can still be changed - Bug fixed: - autopurge/standby option did not worked for closed loop Dansensor control. High flow o/p stayed on even after purge timeout. Without closed loop, once low flow is active, purge is not activated by sensor input. Note: For Autopurge/standby option, all entrance sensor inputs are always active even board/smema opotiona are not selected. - Bug fixed: 1913 model with cool zone1 heater setup, cool zone PV was grayed out model: zone 14 PV were grayed out.

3 Sep DY sensor capability - Hyperterminal read for Hygrometer - When program starts, allow time for HC2 to boot completely before generating communication error - Added SECSGEM events for board entry and exit - Added feature to allow custome bitmap for N2 on/off and CBS up/down buttons. (N2ON.bmp, N2OFF.bmp, CBSUP.bmp, CBSDOWN.bmp). - Startup sequence delay for "Audible alarm on all warning" option is removed ECN Nov When "Disable autoacknowledge warnings" selected, autoacknowledge warnings for heat-belt warning untill startup sequence is finished +2min. - Audible alarm on all warnings is not active during startup sequence +2min. - Bug fix: Calender issue with Japanese language - Bug fix: Unstable belt speed when exit sensor is blocked - HC2 driver version check during program start is updated to check for exact match. Previous versions were checking only for older version SMEMA operation tie-up with barcode program - improved barcode-smema operation on dual lane smema - Fixed: N2 button bitmap with password protection was not representing actual N2 on/off when clicked Cancel on password window. - Recipe name in Winkic when cooldown is loaded displays COOLDOWN now Jan Added Features: - Blower RPM display on overview screen (Heat and cool zones) - Data logging for blower RPM - Message/Warning/Alarm for heat zones based on blower RPM - Added fix for ActiveX function calls (KIC, ECD). Issue was that user thread can request data before communication thread populates buffer data. - Fixed: single channel Dansensor communication message was not regenerating after acknowledged in alarm window patch Jan Improved HC2 comm loss error mechanism. Allow 15sec to recover communication, (changed from 5sec) Mar ActiveX function change for rail width change (for Mydata Line Control software).

4 Mar Fixed: 1914 R-L model overview layout - Fixed: 1913 R-L with visible flux heater overview layout - Fixed: 1913 with non-visible flux heater chanel issue. Flux1 heater channel was hidden under top13 zone May Touch screen optimized version May Add Top and Bottom temperature zones graph view - Separate digital output for Audible Warning conditions - Production capacity display feature added - HC2 global high process alarm max limit changed from 650C to 1000C. - SECSGEM VID 1011, 1013 generated to match with manual. -1 is added for unused/disabled channels, same as VID ActiveX notification event correction for events 20,21,60, June Added intelligent exhaust option - Added standby blower speed option - New ActiveX function to read Flux heater channel SP & PV Aug Predefined board animation length (CO60122) - Added "STANDBY MODE" label on overview when blower standby mode is active - ActiveX event 61 (board exit) correction - Setup wizard: allow independent sensor distance for Lane 1 and 2. - Data logging in decimal for PV and OP% - Fixed: CBS up/down button display when set to Classic mode - Fixed: CC Rail Jog mode overview display - Fixed: Red light and audible warning on board drop/stop option Sep Added idle mode energy saving feature; a standby recipe or cooldown mode can be loaded when no boards in oven for set time.

5 Nov Fixed an issue where oven was not controlling to SP when recipe is loaded after autoclean job or by barcode program - Added option: Custom Warning/Alarm 3 - Added option: Board warning digital output per lane - Special (SEC) light tower on-off control - Added new event to log recipe name after midnight date roll over - Fixed an issue with KIC functionality for take/release control, set point transfer and saveas kicprofile recipe. (KIC2000 version 3001). - removed "Regain Control" sub menu under Utilities - Pop up messages for oven release/regain control are removed. Append title bar to display remote control when oven program released control to third party program like SECS/GEM - Improved rail exercise functionality - Fixed an issue when rail is switched from manual to computer mode during recipe load; wait for user responce before moving rail - Fixed an belt stop issue when Auto log down feature is enabled. This was noticed in Dec Rev-B ECN A Mar Rev-C ECN Max board count in oven with SMEMA option added - Fixed: an issue for warning message needs to click more than once - Fixed an issue with high CPU usage when oven program is in operate mode running recipe C May Fixed a program crash related to closed loop Dansensor with Standby option Feb Dual light tower option added. Total two light towers, for Lane1 and Lane2 each. - Dual lane special barcode system (Micron XXxxxxxxx-XXX-XXX) - For flux heater channel setup, display all 32 channels as part of drop down box Feb ActiveX function call correction for GetRailWidth - ActiveX function call possible for rail width setting while boards in oven for other lane - Fixed: belt speed going to 0 when SP change using activex

6 Mar Imported heat zone cooling PID option from version - Added heat zone cooling on/off control selection (default) - Option to allow heat zone cooing output to skip startup sequence - Option to allow heat zone cooling output to be active in cool-down mode - Previous version recipe compatibility when heat zone cooling option is enabled - Global high process alarm Min setting possible is 25C (previously 200C) Mar Option: Digital output on/off based on board count > set value - Custom warning/alarm option: Change delay time max limit to 9999 from 30sec. - Option to allow blower speed at 100%/High during recipe startup sequence A Mar Fixed an issue with high CPU usage when oven program is in operate mode running recipe Apr Option added: Energy saving setup window Apr Board count/processing issue related to exit cutout distyance setup May Added Custome light tower setup option - Update for multi-lane (smema) barcode system Jul Added Alarm scanner option (using monitoring HC2 ctrl.) void Jul Bugfix: Micron barcode fix (XXxxxxxxx-XXX-XXX) - Improved communication - Note: 1913 model disabled Aug Fixed: 1913 RL model - Previous recipe load without rail move and count reset - Add light tower setup for Ready (products in oven) mode - Setup wizard issue when back from page Ocx/ActiveX corrections/update - KICLDO communication file for custom 3rd party functionality Add [LDO_INFO] tag to LDOChange file for KICLDO option - HC2updater change to not display confirmation message for every file - Corrected issue for touch screen optimized option

7 Add capability for recipe name to include '.' - Fix: a blank string for S7F19 SECSGEM (list of recipe names) when oven program is in cooldown mode - Change language INI file entry IDSA_HIGH_H2O_TEMP=High water temp./low water flow alarm, Cooldown Loaded! - INI file spelling corrections: Exhuast to Exhaust - Added a log entry for recipe Save As to include recipe name - Fixed: Board stop warning did not worked in previous version - Fixed: Recipe name update in barcode program when loaded via calender - Added: Pegatron board entry barcode data logging option - Changed event log text file open behaviour: instead of open-close at each event, open when program starts and close when program close Aug Added: Harman MES option - Added new languages: Portugese, Vietnamese - Removed option to exit without HC2 shutdown - Correction: Pegatron board entry barcode data log option per customer feedback - Fixed: Calender event countdown bar was not working, noticed during tests, - Added new oven models: 1910(10 zones), 1911(11 zones) - Fixed: an issue of heat channel color staying red when recipe is reloaded using previous recipe load button - Added: S7F25 (SECS/GEM formatted recipe upload) support - Fixed: Energy saving option correction for certain config Fixed: Belt speed issue when encoder input is on TDM(Voltage type) - Fixed: Green light tower if Dansensor warning is acknowledged individually in alarm screen and warning is still present Nov GMT time for Barcode data log option - Improved PC to HC2 communication, single socket communication - Fixed: Issue of light tower not green when manual hardware rail option is active - Fixed: issue of rail move message does appear when oven program runs for the first time and manual rail input is active - Fixed: issue of OvenCPK Z13T PV value error, always showing Z6T PV

8 Nov Fixed: HC2 reboot after 1024 board entry or after board count reset - Fixed: Animation for board#512 and 1024 was not displayed Dec Added option: Blowers to run at 100% during recipe startup - Fixed: when KIC2000 sends a belt SP to oven program, it was getting converted to inch/min - Update barcode data log (Fuji/Pegatron) option to have intermediate TMP folder - Fixed: Board count reset button for multi-lane setup - Changed default to "Single" blower control for group A, B, C. D and E are already single. - Fixed: issue of oven program icons are not grayed out when program is in external or released control - Fixed: profile port 4, 5 were not reported (ActiveX) to KIC program - Fixed: barcode data log file will not create for 1st board if entrance and exit sensor is blocked at the same time - Fixed: board count, animation did not worked when cut-out distance was set to 0 - Fixed: setup wizard last page, High limit values were not able to change - Fixed: SECS/GEM related issues - - recipe START command was failing - - list of recipe command (s7f19) was not responding - - recipe delete s7f17, recipe upload s7f5, recipe download s7f3 was not responding - Fixed: Energy saving option setup issue: Standby mode-1 timer setting change did not get applied Jan Fixed: Audible alarm silence button is not working in Fixed: Board animation was not accurate when units are in inches with closed loop belt setup. Animation was slower than belt speed. - Fixed: Oven program crash when custom alarm 3 was enabled - Fixed: Dansensor warnings were active even if main N2 switch is OFF position - Applied belt speed slowdown issue correction. Issue was observed on ovens where lots of boards are processed at faster rate.

9 Jan Rev-D ECN Fixed: Program crash when heat zone cooling option is selected - Fixed: Barcode data log option was not working occasionally after program is restarted (specific after two two restarts or if program closed abnormally) - Fixed: board detection period window at exit end was broken in version In setup wizard, below options are now checked ON by default -- Warning on rise rate -- Blowers at 100% during recipe startup (Note: for HC2s with older than driver version, drivers needs to get updated manually before program start) Feb Rev-E ECN Fixed: Barcode audible warning was not generated in previous version - Fixed: Autoclean recipe (Gen5-Recipe) option did not worked in previous version, Autoclean confirmation message did not worked. - Warning on rise rate option is unchecked by default now - Fixed: ActiveX notification events 20, 21 were not generating in previous version