GenePix 4000B ARRAY SCANNER. User s Guide. Part Number Rev E July 2001 Printed in USA

Size: px
Start display at page:

Download "GenePix 4000B ARRAY SCANNER. User s Guide. Part Number 2500-136 Rev E July 2001 Printed in USA"

Transcription

1 GenePix 4000B ARRAY SCANNER User s Guide Part Number Rev E July 2001 Printed in USA The GenePix 4000B Array Scanner is for research purposes only. It is not intended or approved for diagnosis of disease in humans or animals. Copyright Axon Instruments, Inc. No part of this Guide may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, microfilming, recording, or otherwise, without written permission from Axon Instruments, Inc.

2

3 i For Technical Assistance If you need help to resolve a problem, there are several ways to contact Axon Instruments: World Wide Web Phone +1 (510) Fax +1 (510) Technical Support

4

5 iii Important Safety Information for the GenePix 4000B The operator of the GenePix 4000B Array Scanner instrument is assumed to be trained in the correct operation of the instrument and the safety issues. Throughout the GenePix 4000B Array Scanner User s Guide, the word you refers to this trained operator. Using controls, making adjustments, or performing procedures other than those specified in the GenePix 4000B User s Guide may result in hazardous exposure to laser light, high voltage, or moving parts. Exposure to these hazards can cause severe or fatal injury. Safety Text Used In This Guide Make sure you follow the precautionary statements presented in this guide. Warning: Indicates a possibility of severe or fatal injury to the user or other persons if the precautions or instructions are not observed. Caution: Indicates that damage to the instrument, loss of data, or invalid data could occur if the user fails to comply with the advice given. Important: Highlights information that is critical for optimal performance of the system. Note: Identifies items of general interest. The Protective Housing The protective housing and instrument interlocks are designed to protect you from exposure to the laser light, high voltage, or moving parts. You do not need to access the interior of the instrument. There are no serviceable parts inside. Warning: Do not defeat the interlock, open the protective housing, or try to gain access to the interior of the instrument through any other openings. Opening the housing can damage the instrument components and result in hazardous exposure to laser light, high voltage, or moving parts. The GenePix 4000B is a Class I laser device. There are higher power lasers embedded inside it, but the user can not access these. Slides can be placed safely in the laser s scanning area because the slide-loading door has redundant interlocks that block the beams. There are two panels on the device that are not interlocked, but these are fastened with screws and require a tool to remove them. They are shown in the Non-Interlocked Panels section below. Do not remove any screws to open the housing! The lasers inside can cause eye damage before you have a chance to blink! There are high voltages inside. There are no user serviceable parts inside. The unit will be damaged if you attempt to open the protective housing. Interlock Failure Symptoms If you experience any of the following symptoms, you may have an interlock failure. It is unsafe to continue to use the GenePix 4000B with only one interlock functioning. Please contact Technical Support immediately at either of the numbers indicated on the rear panel of the GenePix 4000B. 1. Mirror and lens assembly keeps moving below the slide after the door is opened. 2. The blue Scanning LED on top of GenePix 4000B doesn t extinguish when the door is open. 3. You cannot scan any slides. 4. You can no longer hear the distinctive metal-on-metal sound that the mechanical interlock makes when it falls into place. This normally happens when the slide loading door has opened about ¼. Lasers Cautions Do not stick anything into the openings or vents of the GenePix 4000B, other than loading the slide. You may cause an interlock to fail. Do not attempt to move any parts below the slideholder. You may cause an interlock to fail. Embedded Laser Classification and Power CLASS 1 LASER PRODUCT Wavelength Power Divergence Duration Embedded Laser s Class 532 nm 20 mw <1.2 mrad Continuous Class IIIb 635 nm 15 mw 0.7 mrad Continuous Class IIIb Warning: Exposure to laser light can cause injury. For example, viewing the laser light directly can cause blindness. Safety Information

6 iv Power Supply Classification Axon Part Number High-Voltage Hazard High-voltage electronics can be found in the GenePix 4000B Array Scanner instrument. Under normal operating conditions, you are protected from high voltage within the instrument. Warning: Do not try to gain access to the interior of the instrument. Exposure to high-voltage electronics can cause severe or fatal injury. High-voltage electronics can also be found in the scanner's controlling computer. See the computer manufacturer documentation on the high-voltage hazard warnings. Make sure you follow the instructions on the safe operation of the computer. Hazardous Material Precautions Use standard laboratory procedures and cautions when working with chemicals. Caution: Always follow the manufacturer s precautions when working with chemicals. The manufacturer and/or supplier is not responsible or liable for any damages caused by or as a consequence of the use of any hazardous material. Non-Interlocked Panels View of the bottom of the GenePix showing the screws which hold the top part of the protective housing. DO NOT REMOVE THESE FIVE SCREWS! DANGER Laser radiation when open AVOID DIRECT EXPOSURE TO BEAM Electrical Ratings Input (DC) Max +15 V 2.5 A +5 V 5.5 A -15 V 0.5 A Moving Parts The GenePix 4000B Array Scanner instrument contains moving parts that can cause injury. Under normal operating conditions, the instrument is designed to protect you from the moving parts. The interlock and protective housing are designed so that you cannot access the moving parts during a scan. Warning: Do not try to gain access to the interior of the instrument. The moving parts inside the instrument can cause injury. Maintenance and Service No user maintenance is required. No user service is allowed. If there is a problem, please contact Technical Support. List of Controls This Guide constitutes a list of controls. Caution: Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. Fuses There are no fuses in the GenePix 4000B. GenePix 4000B User's Guide, Copyright Axon Instruments, Inc.

7 v Safety Labels If a label becomes illegible or is missing for any reason, please contact Array System Technical Support for a free replacement label. While waiting for the replacement label, copy the labels shown in this section and attach the copy of the label to the instrument. Symbol Explanations Device standby Ready to scan slide. Stage waiting at the start position. Scanning. Eject. Slideholder ready to be unloaded. Figure 1. Service Contacts and Warning Label Label is affixed at the rear of the GenePix 4000B on the upper half of the protective housing. Attention, see instructions for use! Attention, dangerous voltage! Attention, laser radiation! Figure 2. Identification and Certification Label Label is affixed at he rear of the GenePix 4000B on the lower half of the protective housing. Figure 3. Power Supply Label Label is affixed to the bottom of the power supply. Site Requirements The GenePix 4000B is designed to operate optimally if the site requirements are met. As with any precision optical instrument, care should be taken to maintain a low-dust, low-vibration environment. Temperature and humidity extremes may compromise performance. Environmental Temperature: 50 86º F (10 30º C). Environmental Humidity: 5 95% non-condensing Power Requirements: Input V~, 6A max., Hz. Space Requirements: 18 in deep 13 in wide 7 in high (44.1 cm 33.1 cm 17.8 cm) Weight Requirements: Sufficient to support 35.8 lb (16.2 kg) with minimal vibration. Safety Information

8 vi Informations de sécurité importantes sur le GenePix 4000B L utilisateur de l instrument à laser Array Scanner GenePix 4000B est supposé avoir reçu la formation adéquate sur l utilisation de cet instrument et les consignes de sécurité associées. Le GenePix 4000B Array Scanner User s Guide s adresse à un opérateur qualifié. L utilisation de commandes et l exécution de réglages ou de procédures autres que ceux spécifiés dans le GenePix 4000B User s Guide entraîneraient de graves dangers d exposition au faisceau laser, à des hautes tensions ou à des pièces mobiles. Ces dangers peuvent être à l origine de dommages corporels sévères ou fatals. Informations de sécurité utilisées dans ce Guide Veillez à prendre les précautions indiquées dans ce guide. Avertissement: Indique un risque de dommage corporel sévère ou fatal pour l utilisateur ou d autres personnes si les précautions ou les instructions indiquées n étaient pas observées. Attention: Indique un risque de dommage pour l instrument, de perte de données ou de données invalides si l utilisateur ne suit pas les recommandations de ce manuel. Important: Désigne des informations vitales pour le fonctionnement optimal du système. Note: Identifie des informations d intérêt général. Le boîtier de protection Le boîtier et les verrouillages de sécurité de l instrument sont conçus pour vous protéger du danger d exposition au faisceau laser, à des hautes tensions ou à des pièces mobiles. Il n est pas nécessaire que vous accédiez à l intérieur de l instrument, où aucune intervention n est nécessaire. Avertissement : Ne désactivez pas les verrouillages de sécurité, n ouvrez pas le boîtier et ne tentez pas d accéder à l intérieur de l instrument par aucune autre ouverture. L ouverture du boîtier pourrait endommager les composants de l instrument et entraîner un danger d exposition au faisceau laser, à de hautes tensions ou à des pièces mobiles. Le GenePix 4000B est un instrument à laser de Classe 1. Il incorpore des lasers de puissance, auxquels l utilisateur ne peut pas accéder. Les lames peuvent être placées en toute sécurité dans la zone de balayage des lasers : la porte coulissante bloque automatiquement l émission des rayons lors de son ouverture. Il y a deux accès potentiels sous l appareil qui ne possèdent pas cette protection : ils sont fermés par des vis et requièrent donc l usage d outils pour leur ouverture (voir les figures ci-dessous). N enlevez aucune vis pour tenter d ouvrir le boîtier ou pour aucune autre raison. Les lasers internes peuvent endommager vos yeux avant que vous n ayez le temps de les fermer! Attention! Présence de hautes tensions à l intérieur. L utilisateur ne doit procéder à aucune intervention à l intérieur du boîtier. L appareil peut être endommagé par une simple tentative d ouverture du boîtier. Symptômes Liés aux Problèmes de Verrouillage Il est dangereux de continuer à utiliser le GenePix 4000B si seul l un des deux verrouillages de sécurité fonctionne. Prière de contacter le fabricant et/ou le fournisseur immédiatement à l un des numéros indiqués à l arrière du GenePix 4000B. L apparition de l un des symptômes suivants désigne un problème avec la double protection : 1. L ensemble miroirs-lentilles continue à se déplacer sous la lame après l ouverture de la porte coulissante. 2. La DEL Scanning (voyant bleu) sur le dessus du GenePix 4000B ne s éteint pas quand la porte est ouverte. 3. Il vous est impossible de scanner une lame. 4. Vous n entendez plus le bruit métallique caractéristique que provoque le verrouillage mécanique lorsqu il est enclenché. Ce clic s entend normalement dès que la porte coulissante est ouverte d un quart de pouce (environ 6 mm). Sécurité concernant les Lasers Précautions à prendre CLASS 1 LASER PRODUCT Ne rien introduire dans les ouvertures ou aérations du GenePix 4000B, à part une lame de microscope dans le compartiment prévu pour son chargement. Vous pourriez provoquer une défaillance des systèmes de sécurité (systèmes à double verrouillage). Ne pas tenter de déplacer un composant derrière le support des lames. Ceci risquerait de provoquer une défaillance des systèmes de sécurité (systèmes à double verrouillage). GenePix 4000B User's Guide, Copyright Axon Instruments, Inc.

9 vii Puissance et Classification des Lasers Utilisés Longueur d onde Puissance Divergence Durée Classe des lasers embarqués 532 nm 20 mw <1.2 mrad Continue Classe IIIb 635 nm 15 mw 0.7 mrad Continue Classe IIIb Avertissement : L exposition au faisceau laser peut entraîner des dommages corporels. Par exemple, fixer directement le laser entraîne un risque de cécité. Classification de l alimentation Fusible Il n existe pas de fusible à l intérieur du GenePix 4000B. Précautions contre les substances dangereuses L utilisateur doit suivre les procédures standard de laboratoires et prendre les précautions appropriées à la manipulation de produits chimiques. Attention : Veillez à toujours suivre les consignes de sécurité du fabricant lors de la manipulation de produits chimiques. Le fabricant et/ou le fournisseur ne peuvent être tenues pour responsables de dommages éventuels, directs ou indirects, causés par l utilisation de substances dangereuses. Accès non verrouillés par la Double Protection Référence Axon Danger de haute tension Des circuits à haute tension se trouvent à l intérieur de l instrument à laser Array Scanner GenePix 4000B. Dans des conditions d utilisation normales, vous êtes protégé(e) des hautes tensions à l intérieur de l instrument. Avertissement : Ne tentez pas d accéder à l intérieur de l instrument. L exposition à des circuits à haute tension peut provoquer des dommages corporels sévères ou fatals. Il existe également des circuits à haute tension dans l ordinateur contrôlant le scanner. Reportez-vous à la documentation du fabricant de l ordinateur sur les risques liés à ces hautes tensions. Suivez les instructions concernant les précautions d utilisation de l ordinateur. Entrée (courant continu) Maximum +15 V 2.5 A +5 V 5.5 A -15 V 0.5 A Pièces mobiles L instrument à laser Array Scanner GenePix 4000B contient des pièces mobiles pouvant entraîner des risques de dommages corporels. Dans des conditions d utilisation normales, cet instrument est conçu pour vous éviter tout risque lié aux pièces mobiles. Le système de sécurité et le boîtier de protection sont conçues pour prévenir tout accès aux pièces mobiles durant l utilisation du scanner. Avertissement : Ne tentez pas d accéder à l intérieur de l instrument. Il existe des pièces mobiles à l intérieur susceptibles de provoquer des dommages corporels. Vue de dessous du GenePix montrant les vis qui maintiennent la partie supérieure du boîtier. NE PAS RETIRER CES CINQ VIS! DANGER! Radiation laser lorsque ouvert EVITER IMPERATIVEMENT L EXPOSITION DIRECTE AUX RAYONS Maintenance et Service des accès non verrouillés par la Double Protection Aucune maintenance de la part de l utilisateur n est nécessaire. De plus, auun service de maintenance n est autorisé de la part d un tiers. Liste des Contrôles Ce guide constitue une liste des contrôles à effectuer régulièrement. Attention : Tout contrôle, réglage ou exécution de procédures autres que celles spécifiées ci-dessus peut entraîner un risque d exposition dangereuse à des rayonnements. Informations de sécurité

10 viii Etiquettes de sécurité Si une étiquette devient illisible ou manque pour une raison quelconque, contactez le service Support du Array System pour obtenir gratuitement une étiquette de remplacement. En attendant, copiez les étiquettes illustrées dans ce manuel et attachez cette copie à l instrument. Symboles d alerte (Signalétique) Significations des Symboles Appareil en attente. Prêt à scanner une lame. Attend en position de départ. Balayage en cours. Ejection. Support de lame accessible. Figure 1. Adresse et avertissements Cette étiquette est collée à l arrière du GenePix 4000B sur la partie supérieure du boîtier. Attention, voir les instructions d utilisation! Attention, haute tension! Danger! Attention, rayonnement Laser! Figure 2. Identification et étiquette de certification Cette étiquette est collée à l arrière du GenePix 4000B sur la partie inférieure du boîtier. Conditions nécessaires sur le site Le GenePix 4000B est conçu pour fonctionner au mieux de ses performances si les conditions nécessaires sur le site sont satisfaites. Comme pour tout autre instrument optique de précision, il ne doit pas être exposé à la poussière et aux vibrations. Des conditions extrêmes de température et d humidité peuvent compromettre ses performances. Température : 10-30º C. Humidité : 5-95% sans condensation Alimentation : V~, 6A max., Hz. Espace nécessaire : 44,1 cm 33,0 cm 17,8 cm Poids : Structure suffisante pour supporter un poids de 16,2 kg pratiquement sans vibration. Figure 3. Étiquette de l alimentation. Cette étiquette est fixée sur le bas du l alimentation. GenePix 4000B User's Guide, Copyright Axon Instruments, Inc.

11 Información Importante sobre la Seguridad del GenePix 4000B ix Se asume que el operador del GenePix 4000B Array Scanner está entrenado en las precauciones de seguridad a seguir y en la utilización correcta del instrumento. La palabra usted como se utiliza en esta guía del usuario del GenePix 4000B Array Scanner se refiere a este operador entrenado. Utilización o ajuste de los controles y la ejecución de procedimientos diferentes a los especificados en la guía del usuario del GenePix 4000B, puede resultar en exposición peligrosa a radiación láser, alto voltaje o a partes móviles. Exposición a estos peligros pueden producir lesiones severas o fatales. Declaraciones de Seguridad Utilizadas en esta Guía Cerciorése de observar las declaraciones de seguridad que se presentan en esta guía. Advertencia: Indica la posibilidad de lesión severa o fatal al usuario u otras personas si no se siguen las instrucciones y precauciones. Precaución: Indica que puede ocurrir daño del intrumento, pérdida o invalidéz de la información obtenida si el usuario no obedece las instrucciones provistas. Importante: Resalta información fundamental para el funcionamiento óptimo del sistema. Nota: Identifica aspectos de interés general. Cubierta Protectora La cubierta protectora y el circuito de seguridad del instrumento están diseñados para protegerlo a usted de exposición a la radiación láser, alto voltaje o a partes móviles. Usted no necesita acceder al interior del instrumento. En el interior no hay partes que requieran su servicio. Advertencia: No fuerce el circuito de seguridad, ni abra la cubierta protectora o intente acceder al interior del instrumento a través de cualquiera de sus aperturas. Abrir la cubierta protectora puede ocasionar daño en los componentes del instrumento y producir exposición accidental a la radiación láser, al alto voltaje o a partes móviles. El GenePix 4000B es un equipo de láser de Clase 1. Adentro se localizan láseres de alta potencia fuera del alcance del usuario. Las placas pueden colocarse sin peligro en la región del area de barrido del láser porque la entrada de las placas tiene circuitos de seguridad redundantes que bloquean los rayos de luz. Hay dos paneles en el equipo que no son parte del circuito de seguridad, pero que están asegurados con tornillos que requieren una herramienta para sacarlos. Estos están indicados mas adelante. No remueva ningún tornillo para abrir la cubierta! Los láseres interiores pueden dañar sus ojos antes de que pueda pestañear. Interiormente hay altos voltajes. En el interior no hay partes que requieran servicio por parte del usuario. La unidad se dañará si usted intenta abrir la cubierta protectora. Síntomas de Daños en el Circuito de Seguridad Si usted encuentra cualquiera de los siguientes síntomas, el circuito de seguridad podría estar dañado. Es peligroso continuar usando el GenePix 4000B cuando hay sólo un circuito de seguridad funcionando. Comuníquese al mantenimiento técnico a cualquiera de los números telefónicos indicados en la parte posterior del GenePix 4000B. 1. El espejo y el montaje de los lentes siguen moviéndose por debajo de la placa después de abrir la puerta. 2. La luz azul emitida por el diodo LED con etiqueta Scanning localizado en la parte superior del GenePix 4000B no se extingue cuando la puerta está abierta. 3. Usted no puede registrar ninguna placa. 4. No se puede escuchar el sonido característico del contacto entre metales producido por el circuito de seguridad cuando se ajusta en su lugar. Este ocurre normalmente cuando la apertura donde se coloca la placa se abre aproximadamente 6 mm. Seguridad del Láser Precauciones CLASS 1 LASER PRODUCT No inserte ningún objeto en las aperturas o respiraderos del GenePix 4000B diferente de la placa. Puede ocasionar fallas en el circuito de seguridad. No intente mover ningún componente debajo de la platina. Usted puede causar fallas en el circuito de seguridad. Información sobre la Seguridad

12 x Clasificación y Potencia de los Láseres Incluidos Longitud de Onda Potencia Divergencia Duración Tipo de Láser 532 nm 20 mw <1.2 mrad Continua Clase IIIb 635 nm 15 mw 0.7 mrad Continua Clase IIIb Advertencia: Exposición a la radiación láser puede ocasionar lesiones. Por ejemplo, mirar directamente a la luz del láser puede causar ceguera. Clasificación de la Unidad de Poder Precaucions con Materiales Peligrosos El usuario debe utilizar procedimientos y precauciones de laboratorio estandarizados cuando trabaja con productos químicos. Advertencia: Utilice siempre las instrucciones de la fábrica cuando trabaje con productos químicos. El fabricante y/o el proveedor no son responsables legalmente por daños o lesiones ocasionados como consecuencia del uso de materiales peligrosos. Paneles Que No Forman Parte del Circuito de Seguridad Vista de la base del GenePix mostrando los tornillos que aseguran la parte superior de la cubierta protectora. NO REMUEVA ESTOS CINCO TORNILLOS! El número de Parte de Axon Instruments es PELIGRO Radiación con laser si se abre EVITE EXPOSICIÓN DIRECTA AL RAYO LASER Peligro de Alto Voltaje El GenePix 4000B Array Scanner contiene electrónica de alto voltaje. Bajo condiciones normales de operación, usted está protegido del alto voltaje del instrumento. Advertencia: No intente acceder al interior del instrumento. Exposición a alto voltaje puede causar lesiones severas o fatales. Electrónica de alto voltaje se encuentra en el computador que controla el escáner. Revise la documentación del fabricante sobre las advertencias al respecto. Cerciorese de seguir cuidadosamente las instrucciones sobre la utilización apropiada del computador. ENTRADA (CORRIENTE CONTINUA) Máxima +15 V 2.5 A +5 V 5.5 A -15 V 0.5 A Partes Móviles El GenePix 4000B Array Scanner contiene partes móviles que pueden causar lesiones. El instrumento está diseñado para protegerlo a usted de las partes en movimiento en condiciones normales de funcionamiento. El circuito de seguridad y la cubierta protectora impiden el acceso al interior del instrumento durante un escan. Advertencia: No intente acceder al interior del instrumento. Las partes móviles pueden causar lesiones. Fusibles El GenePix 4000B no contiene fusibles. Mantenimiento y Reparación No se requiere ningún mantenimiento por parte del usuario. Este no está autorizado para ejecutar ninguna reparación. Si hay algún problema por favor comuníquese al mantenimiento técnico a cualquiera de los números telefónicos indicados en la etiqueta. Lista de Controles Este guía provee una lista de controles. Precaución el uso de los controles, el ajuste o la ejecución de procedimientos diferentes de los especificados aquí puede resultar en exposición peligrosa a la radiación del laser. GenePix 4000B User's Guide, Copyright Axon Instruments, Inc.

13 xi Etiquetas de Seguridad Si una etiqueta se hace ilegible o se pierde por algun motivo, por favor contacte el servicio técnico del sistema para obtener etiquetas sin costo alguno. Mientras espera por las etiquetas de reemplazo, copie las que aparecen en esta sección y pegue una copia en el instrumento. Explicaciones de los Símbolos El equipo está a la espera ( Standby ). La platina está lista en posición de cargar la diapositiva y empezar. Símbolos de Advertencia Registrando ( Scanning ). Expulse ( Eject ). La platina está lista para descargar. Figura 1. Etiqueta con Advertencias y Contactos para Reparación La etiqueta está fijada a la parte posterior del GenePix 4000B en la mitad superior de la cubierta protectora. Atención, vea instrucciones para su uso! Atención, voltajes peligrosos! Atención, radiación del láser! Figura 2. Etiqueta de Identificación y Certificación La etiqueta está fijada a la parte posterior del GenePix 4000B en la mitad inferior de la cubierta protectora. Figura 3. Etiqueta de la Unidad de Poder. La etiqueta está fijada en la base de la unidad de poder. Requerimientos del Lugar de Instalación El GenePix 4000B está diseñado para operar óptimamente si el lugar de instalación cumple con los requerimientos. Como con cualquier instrumento óptico de precisión debe tener cuidado de manterlo en un lugar bajo en polvo, y de poca vibración. Temperaturas extremas y humedad pueden comprometer su funcionamiento. Temperatura ambiental: ºF (10-30 ºC). Humedad ambiental: 5-95% sin condensación. Energía requerida: Entrada: V, 6 A máximo; Hz. Espacio requerido: 18" profundidad 13" amplitud 7" altura (44.1 cm 33.0 cm 17.8 cm). Peso requerido: Suficiente para sostener 35.8 lb (16.2 kg) con mínima vibración. Información sobre la Seguridad

14 xii Wichtige Sicherheitsmassnahmen für GenePix 4000B Es wird vorausgesetzt, dass der Benutzer des GenePix 4000B qualifiziert ist, das Gerät richtig und sicher zu verwenden. Innerhalb der gesamten Beschreibung für den GenePix 4000B Array Scanner bezieht sich das Wort Sie auf diesen qualifizierten Benutzer. Die Benutzung der Kontrollvorrichtungen, Änderungen oder das Ausführen anderer Handlungen ausser denen, die in der Gebrauchsanweisung des GenePix 4000B erklärt sind, können zu gefährlichen Strahlungen, hoher Voltzahl oder losen Teilen führen. Kontakt mit diesen Gefahren kann zu schweren oder tödlichen Verletzungen führen. Sicherheitstext, der in dieser Gebrauchanweisung verwendet wird Versichern Sie sich bitte, dass Sie alle Vorsichtsmassnahmen beachten. Warnung: Weist auf die Möglichkeit einer schweren oder tödlichen Verletzung hin, wenn die Anweisungen oder Vorsichtsmassnahmen nicht beachtet werden. Achtung: Weist darauf hin, dass bei Nichtbeachtung der Vorschriften Schaden am Gerät entstehen kann und Datenausfall oder möglicherweise ungültige Daten resultieren können. Wichtig: Weist auf Information hin, die wichtig ist um die optimale Leistung des Gerätes sicherzustellen. Anmerkung: Deutet auf Themen von generellem Interesse hin. Das Schutzgehäuse Das Schutzgehäuse und die elektrische Verriegelung sind so konstruiert, dass Sie vor Laserstrahlen, Hochspannung und beweglichen Teilen geschützt sind. Sie brauchen das innere Teil des Gerätes nicht zu öffnen, weil keine für den Nutzer justierbaren Teile vorhanden sind. Warnung: Verändern Sie nicht die elektrische Verriegelung. Öffnen Sie nicht das Schutzgehäuse oder versuchen Sie gleichermassen nicht, das Innere des Gerätes durch andere Öffnungen zu erreichen. Der GenePix 4000B ist ein Laserprodukt der Klasse 1. Auf den Bereich der im Gerät entstehenden stärkeren Laserstrahlen hat der Benutzer kein Zugriff. Glasstreifen können sicher in den Laserrasterbereich eingeführt werden, weil die ladende Tür mehrere Verriegelungen hat, die Laserstrahlen blockieren. Es gibt zwei Öffnungen, die nicht elektrisch verriegelt, sondern mit Schrauben befestigt sind. Diese können nur mit Hilfe eines Werkzeuges entfernt werden. Sie sind unten abgebildet. Entfernen Sie niemals die Schrauben, um das Gehäuse zu öffnen! Die im Gerät enstehenden Laserstrahlen können Ihre Augen beschädigen, bevor Sie Gelegenheit haben, sich zu schützen. Im Gerät entstehen hohe Spannungen. Es befinden sich im Gerät keine für den Nutzer justierbaren Teile. Wenn Sie versuchen, das Schutzgehäuse zu öffnen, kann dies eine Beschädigung des Gerätes zur Folge haben. Hinweise auf ein Versagen der elektrischen Verriegelung Wenn eines der nachfolgenden Probleme auftritt, hat wahrscheinlich eine Verriegelung versagt. Es ist sehr gefährlich, weiterhin den GenePix 4000B zu benutzen, wenn nur eine elektrische Verriegelung funktioniert. Bitte rufen Sie sofort den Technischen Hilfsdienst an, sobald eines der unten beschriebenen Symptome auftritt. Die Service-Nummern befinden sich auf der hinteren Seite des Gerätes. 1. Spiegel- und Linsensysteme bewegen sich weiterhin unter dem Objektträger, nachdem die Tür geöffnet wurde. 2. Die blaue Scanning Lichtdiode oben auf dem GenePix 4000B erlöscht nicht, wenn die Tür geöffnet wird. 3. Sie können keine Glasstreifen ablesen. 4. Der Benutzer hört nicht mehr das metallene Geräusch, welches bei normaler Funktion durch das Einrasten der mechanischen Verriegelung ausgelöst wird. Dies passiert normalerweise, wenn die Tür ungefähr 6 mm geöffnet ist. Lasersicherheit Achtung CLASS 1 LASER PRODUCT Mit Ausnahme des Objektträgers dürfen unter keinen Umständen Gegenstände in die Öffnungen oder Ausgänge des GenePix 4000B gesteckt werden, da sonst ein Versagen der elektrischen Verriegelung verursacht werden könnte. Unterhalb des Objektträgers dürfen keine Teile bewegt werden, auch dies könnte ein Versagen der elektrischen Verriegelung verursachen. GenePix 4000B User's Guide, Copyright Axon Instruments, Inc.

15 xiii Klassifizierung und Intensität der benutzten Laser Wellenlänge Stärke Divergenz Betriebsart Klassifizierung 532 nm 20 mw <1.2 mrad Kontinuierlich Klasse IIIb 635 nm 15 mw 0.7 mrad Kontinuierlich Klasse IIIb Warnung: Verletzungen können enstehen, wenn man Laserstrahlen ausgesetzt wird. Direkter Kontakt mit den Strahlen kann zu Blindheit führen. Stromversorgung (Klassifikation) Sicherheitsvorkehrungen Der Benutzer muss alle normalen Laboranweisungen und Sicherheitsvorkehrungen befolgen, wenn Chemikalien verwendet werden. Achtung: Befolgen Sie immer die Anweisungen der Hersteller, wenn Sie mit Chemikalien arbeiten. Der Hersteller und/oder der Lieferant übernehmen keine Verantwortung für Schäden, die durch den Missbrauch von gefährlichen Chemikalien verursacht werden. Geräteöffnungen Ohne Elektrische Verriegelung Die untere Ansicht des GenePix zeigt die Schrauben welche den oberen Teil des Schutzgehäuses zusammenhalten. ENTFERNEN SIE DIESE FUNF SCHRAUBEN UNTER KEINEN UMSTÄNDEN! Axon Teil Nr Hochspannungsgefahr Der GenePix 4000B Array Scanner enthält Hochspannungselektronik. Unter normalen Gebrauchskonditionen sind Sie vor diesen Spannungen geschützt. Warnung: Versuchen Sie nicht an das innere Teil des Scanners heranzukommen. Kontakt mit der Hochspannungselektronik kann schwere oder tödliche Verletzungen verursachen. Hochspannungselektronik befindet sich auch im Kontrollrechner des Gerätes. Lesen Sie sich bitte die Gebrauchsanweisung über die Hochspannungsgefahr durch. Befolgen Sie alle Anweisungen über die Sicherheitsmassnahmen beim Gebrauch des Rechners. Eingabe (Gleichstrom) Maximal +15 V 2.5 A +5 V 5.5 A -15 V 0.5 A Bewegliche Teile Der GenePix 4000B Array Scanner enhält bewegliche Teile, die Verletzungen verursachen können. Unter normalen Umständen ist das Gerät so konstruiert um Sie vor den beweglichen Teilen zu schützen. Die Verrieglung und das Schützgehäuse sind da, damit ein Zugriff auf die beweglichen Teile während einer Ablesung nicht möglich ist. Warnung: Versuchen Sie nicht, das innere Teil des Gerätes zu öffnen. Die darin enthaltenen beweglichen Teile können Verletzungen verursachen. Sicherung Es befinden sich im GenePix 4000B keine Sicherungen. VORSICHT!! Laserbestrahlung wenn geöffnet!! VERMEIDEN SIE DIREKTEN KONTAKT MIT DEM LASERSTRAHL! Instandhaltung und Vorsorge Es ist keine Vorsorge durch den Benutzer nötig. Jede eigenmächtige Reparatur durch den Benutzer ist untersagt. Wenn ein Problem auftritt, dann rufen Sie bitte den Technischen Hilfsdienst an. Liste von Kontrollvorrichtungen Diese Gebrauchsanweisung enthält eine Liste der Kontrollvorrichtungen. Achtung Der Gebrauch von Kontrollvorrichtungen oder Einstellungen bzw. die Ausführung von Handlungen außer denen, die in dieser Anweisung beschrieben sind, können zu gefährlichen Strahlungen führen. Sicherheitsmassnahmen

16 xiv Sicherheitsetiketten Sollte ein Etikett unlesbar werden oder aus unbekannten Gründen fehlen, setzen Sie sich bitte mit dem Technischen Hilfsdienst für einen kostenlosen Ersatz des Etiketts in Verbindung. Während Sie auf das Etikett warten, kopieren Sie die Etiketten am Ende dieses Abschnitts und befestigen Sie eine Kopie des Etiketts am Gerät. Abbildungen mit Sicherheitshinweisen Erklärung Der Symbole Standby-Modus. (Gerät ist bereit einen Objektträger zu lesen. Führung des Objektträgers in Startposition) Scanning. Eject. (Gerät ist bereit zur Ausgabe des Objektträgers) Abbildung 1.: Kundendienst und Warnetiketten Das Etikett ist auf der Rückseite des GenePix 4000B auf dem oberen Teil des Schutzgehäuses befestigt. Abbildung 2. Identifikations- und Beglaubigungsetikett Das Etikett ist auf der Rückseite des GenePix 4000B an der unteren Hälfte des Schutzgehäuses befestigt. Abbildung 3. Stromversorgungetikett. Das Etikett befindet sich am boden der Stromversorgung. Achtung!! Vor Benutzung unbedingt die Gebrauchsanweisung lesen! Achtung!! Gefährlicher Stromkreis! Achtung!! Laserbestrahlung!! Örtliche Voraussetzungen Der GenePix 4000B arbeitet optimal, wenn alle Umfeldvorrausetzungen gegeben sind. Genau wie bei anderen optischen Geräten, sollte auch hier ein staub- und schwingungsfreies Umfeld existieren. Extreme Temperaturen und Luftfeuchtigkeit können die optimalen Funktionen des Gerätes beeinträchtigen. Umgebungstemperatur: ºC. Umgebungsluftfeuchtigkeit: 5 95% unkondensiert. Stromvoraussetzung: Zufuhr V~, 6 A max, Hz. Platzvoraussetzung: 44,1 cm 33,0 cm 17,8 cm. Gewichtsvoraussetzung: Genug um 16,2 kg zu unterstützen mit minimalen Schwingungen. GenePix 4000B User's Guide, Copyright Axon Instruments, Inc.

17 xv Declaration of Conformity Manufacturer: Type of Equipment: Model Number: Serial Number: Axon Instruments, Inc Whipple Road Union City, CA USA Array Scanner GenePix 4000B Year of Manufacture: 2000 Application of Council Directives: EC Low Voltage Directive 73/23/EEC as amended EC EMC Directive 89/336/EEC as amended Harmonized Standards to which Conformity is Declared: EN : 1997 (Emmisions), EN : 1997 (Immunity) EN :1993 +A I +A2:1995 EN :1994 +A 11:1996 I, the undersigned, hereby declare that the equipment specified above conforms to the above Directives and Standards. Authorized Signature and Date: (signature on file) Title of Signatory: Declaration of Conformity

18

19 xvii Customer License Agreement Customer License Agreement for Single User of GenePix Pro 3.0. This software is licensed by Axon Instruments, Inc. ("Axon") to you for use on the terms set forth below. By opening the sealed software package, and/or by using the software, you agree to be bound by the terms of this agreement. AXON hereby agrees to grant you a non-exclusive license to use the enclosed AXON software (the "SOFTWARE") subject to the terms and restrictions set forth in this License Agreement. Copyright The SOFTWARE and its documentation are owned by AXON and are protected by United States copyright laws and international treaty provisions. This SOFTWARE may not be copied for resale or for bundling with other products without prior written permission from AXON. Restrictions on Use and Transfer You may not reverse engineer, decompile, disassemble, or create derivative works from the SOFTWARE. Export of Software You agree not to export the SOFTWARE in violation of any United States statute or regulation. Ownership of Software and Media (CD-ROM) You own the media (CD-ROM) on which the SOFTWARE is recorded, but AXON owns the SOFTWARE and all copies of the SOFTWARE. Product Improvements AXON reserves the right to make corrections or improvements to the SOFTWARE and its documentation and to the related media at any time without notice, and with no responsibility to provide these changes to purchasers of earlier versions of such products. Customer License Agreement

20 xviii Term This license is effective until terminated. You may terminate it by destroying the SOFTWARE and its documentation and all copies thereof. This License will also terminate if you fail to comply with any term or condition of this Agreement. You agree upon such termination to destroy all copies of the SOFTWARE and its documentation. Limited Warranty and Disclaimer of Liability AXON warrants that the media on which the SOFTWARE is recorded and the documentation provided with the SOFTWARE are free from defects in materials and workmanship under normal use. For 90 days from the date of receipt, AXON will repair or replace without cost to you any defective products returned to the factory properly packaged with transportation charges prepaid. AXON will pay for the return of the product to you, but if the return shipment is to a location outside the United States, you will be responsible for paying all duties and taxes. Before returning defective products to the factory, you must contact AXON to obtain a Return Merchandise Authorization (RMA) number and shipping instructions. Failure to do so will cause long delays and additional expense to you. AXON has no control over your use of the SOFTWARE. Therefore, AXON does not, and cannot, warrant the results or performance that may be obtained by its use. The entire risk as to the results and performance of the SOFTWARE is assumed by you. Should the SOFTWARE or its documentation prove defective, you assume the entire cost of all necessary servicing, repair or correction. Neither AXON nor anyone else who has been involved in the creation, production, or delivery of this SOFTWARE and its documentation shall be liable for any direct, indirect, consequential, or incidental damages arising out of the use or inability to use such products, even if AXON has been advised of the possibility of such damages or claim. This warranty is in lieu of all other warranties, expressed or implied. Some states do not allow the exclusion or limitation of implied warranties or liability for incidental or consequential damages, so the above limitations or exclusions may not apply to you. U.S. Government Restricted Rights The SOFTWARE and its documentation are provided with RESTRICTED RIGHTS. Use, duplication or disclosure by the U.S. Government is subject to restrictions as set forth in subparagraph (c)(1)(ii) of The Rights in Technical Data and Computer Software clause at DFARS , or subparagraphs (c)(1) and (2) of the Commercial Computer Software -Restricted Rights at 48 CFR , or clause (d) of the NASA Supplement to the FAR, as applicable. Manufacturer is Axon Instruments, Inc., 3280 Whipple Road, Union City, CA, Governing Body This Agreement is governed by the laws of the State of California. GenePix 4000B User's Guide, Copyright Axon Instruments, Inc.

GenePix Personal 4100A MICROARRAY SCANNER

GenePix Personal 4100A MICROARRAY SCANNER GenePix Personal 4100A MICROARRAY SCANNER User s Guide Part Number 2500-0142 Rev E August 2005 Printed in USA Copyright 2005 Axon Instruments / Molecular Devices Corp. No part of this manual may be reproduced,

More information

Rack Mount Kit Install Guide: Intel Entry Server Chassis SC5295-E UP/DP/WS/BRP Intel Entry Server Chassis SC5299-E DP/WS/BRP

Rack Mount Kit Install Guide: Intel Entry Server Chassis SC5295-E UP/DP/WS/BRP Intel Entry Server Chassis SC5299-E DP/WS/BRP Rack Mount Kit Install Guide: Intel Entry Server Chassis SC5295-E UP/DP/WS/BRP Intel Entry Server Chassis SC5299-E DP/WS/BRP A Guide for Technically Qualified Assemblers of Intel Identified Subassemblies/Products

More information

Operation Instructions PowerCool Series

Operation Instructions PowerCool Series Operation Instructions PowerCool Series TOP VIEW BOTTOM VIEW PDCOOL-05RA PDCOOL-00RK PDCOOL-5R PDCOOL-0R ALSO AVAILABLE Thank you for purchasing the PowerCool Series component cooler and power distribution.

More information

Rail Kit Install Guide: Intel Modular Server System MFSYS25 A Guide for Technically Qualified Assemblers of Intel Identified Subassemblies/ Products

Rail Kit Install Guide: Intel Modular Server System MFSYS25 A Guide for Technically Qualified Assemblers of Intel Identified Subassemblies/ Products Rail Kit Install Guide: Intel Modular Server System MFSYS25 A Guide for Technically Qualified Assemblers of Intel Identified Subassemblies/ Products Intel Order Number: E12567-002 Disclaimer Information

More information

Sun StorEdge A5000 Installation Guide

Sun StorEdge A5000 Installation Guide Sun StorEdge A5000 Installation Guide for Windows NT Server 4.0 Sun Microsystems, Inc. 901 San Antonio Road Palo Alto, CA 94303-4900 USA 650 960-1300 Fax 650 969-9131 Part No. 805-7273-11 October 1998,

More information

Backup Battery Kit Install Guide: Intel Storage Controller AXXSCM3S

Backup Battery Kit Install Guide: Intel Storage Controller AXXSCM3S Backup Battery Kit Install Guide: Intel Storage Controller AXXSCM3S A Guide for Technically Qualified Assemblers of Intel Identified Subassemblies/ Products Intel Order Number: E13860-004 Disclaimer Information

More information

Media Changer/Recorder VGP-XL1B. Safety Information

Media Changer/Recorder VGP-XL1B. Safety Information Media Changer/Recorder VGP-XL1B Safety Information Notice 2006 Sony Electronics Inc. Reproduction in whole or in part without written permission is prohibited. All rights reserved. This manual and the

More information

Installation and Operation Manual Blackmagic MultiDock. Mac OS X Windows

Installation and Operation Manual Blackmagic MultiDock. Mac OS X Windows Installation and Operation Manual Blackmagic MultiDock Mac OS X Windows July 2013 Welcome Welcome to Blackmagic MultiDock! Blackmagic MultiDock is an extremely fast SSD and HDD docking solution that lets

More information

IMATION SECURE SCAN. ck Start Guide. Imation Secure Scan

IMATION SECURE SCAN. ck Start Guide. Imation Secure Scan IMATION SECURE SCAN Quick ck Start Guide Imation Corp 2012 Imation Secure Scan page 1 of 6 1 Unpacking your Imation Secure Scan The following items are contained inside the case: 1 2 Imation Secure Scan

More information

16-Port Gigabit Green Switch (TEG-S16Dg) 24-Port Gigabit Green Switch (TEG-S24Dg)

16-Port Gigabit Green Switch (TEG-S16Dg) 24-Port Gigabit Green Switch (TEG-S24Dg) 16-Port Gigabit Green Switch (TEG-S16Dg) 24-Port Gigabit Green Switch (TEG-S24Dg) ŸGuide d'installation rapide (1) ŸTechnical Specifications (3) ŸTroubleshooting (4) 1.02 1. Avant de commencer Contenu

More information

AMPLIFICADORES PARA MÁSTIL Y ALIMENTADORES AMPLIFIERS FOR MAST AND POWER SUPPLIES AMPLIFICATEURS POUR MÂT ET ALIMENTATIONS SERIE 903 SERIES AMPLIFICADOR PARA MÁSTIL - AMPLIFIER FOR MAST - AMPLIFICATEUR

More information

Direct AC Wiring Option Installation Guide

Direct AC Wiring Option Installation Guide Revision A Direct AC Wiring Option Installation Guide The direct AC wiring option enables you to wire AC power directly in to the ADP InTouch. The option kit contains the following parts. 25mm 12mm Caution:

More information

Regulatory Compliance Statement

Regulatory Compliance Statement Regulatory Compliance Statement 0560 EU Declaration of Conformity The declaration of conformity may be consulted at www.kobo.com/userguides SAR Limits The exposure standard for wireless devices employs

More information

ALIMENTADORES POWER SUPPLIES ALIMENTATIONS ALIMENTAÇÃOS NETZGERÄT SERIE 903 SERIES

ALIMENTADORES POWER SUPPLIES ALIMENTATIONS ALIMENTAÇÃOS NETZGERÄT SERIE 903 SERIES ES POWER SUPPLIES ALIMENTATIONS ALIMENTAÇÃOS NETZGERÄT SERIE 903 SERIES CARACTERÍSTICAS PRINCIPALES MAIN FEATURES PRINCIPALES CARACTERISTIQUES CARACTERISTICAS PRINCIPAIS WESENTLICHE KENNZEICHEN CÓDIGO-CODE-CODE-CODIGO-CODE

More information

Wideband Optical Splitters FOS Series

Wideband Optical Splitters FOS Series Wideband Optical Splitters FOS Series Guide to Installation and Operation M949-9100-103 13 Mar 2014 Miranda Technologies 3499 Douglas-B.-Floreani St-Laurent, Québec, Canada H4S 2C6 Tel. 514-333-1772 Fax.

More information

Gateway Port Replicator User Guide

Gateway Port Replicator User Guide Gateway Port Replicator User Guide Using the Port Replicator Identifying features Connecting and disconnecting the port replicator 1 Using the Port Replicator Top Power button Component Icon Description

More information

USB Data Card Programmer. user s manual and installation guide

USB Data Card Programmer. user s manual and installation guide USB Data Card Programmer user s manual and installation guide 2000 GARMIN Corporation GARMIN International, Inc. 1200 E 151 st Street, Olathe, Kansas 66062 U.S.A. Tel. 913/397.8200 or 800/800.1020 Fax.

More information

RELEASE NOTES. Trimble TerraSync Software. Introduction 简 介

RELEASE NOTES. Trimble TerraSync Software. Introduction 简 介 RELEASE NOTES Trimble TerraSync Software These release notes provide important information about the Trimble TerraSync software version 5.65. Please read these release notes carefully. Introduction New

More information

TABLECLOTHS TEMPLATES

TABLECLOTHS TEMPLATES Hemmed Edges Bords Ourlés / Dobladillo TABLECLOTHS TEMPLATES PLANTILLAS PARA MANTELES / MODÉLES POUR NAPPES 4ft / 1.21m Economy Table Throw Totale de zone Graphique: 103" x 57.5" / 261.6cm x 146 cm Avant

More information

QUICK START BALANCE AUDIO INTERFACE QUICK START DÉMARRAGE RAPIDE KURZANLEITUNG

QUICK START BALANCE AUDIO INTERFACE QUICK START DÉMARRAGE RAPIDE KURZANLEITUNG QUICK START BALANCE AUDIO INTERFACE QUICK START DÉMARRAGE RAPIDE KURZANLEITUNG Quick Start Guide by Fredrik Hylvander The information in this document is subject to change without notice and does not represent

More information

Sun Management Center Change Manager 1.0.1 Release Notes

Sun Management Center Change Manager 1.0.1 Release Notes Sun Management Center Change Manager 1.0.1 Release Notes Sun Microsystems, Inc. 4150 Network Circle Santa Clara, CA 95054 U.S.A. Part No: 817 0891 10 May 2003 Copyright 2003 Sun Microsystems, Inc. 4150

More information

FERRORESONANT BATTERY CHARGERS

FERRORESONANT BATTERY CHARGERS WorkHorse SERIES 1 FERRORESONANT BATTERY CHARGERS Installation and Operating Instructions Applied Energy Solutions, LLC. One Technology Place Caledonia, New York 14423 (585) 538-4421 www.appliedenergysol.com

More information

Ready. Set. Go. Pick a spot and plug it in.

Ready. Set. Go. Pick a spot and plug it in. Ready. Set. Go. Pick a spot and plug it in. Download the Nest app for Android or ios and follow the simple setup instructions. It should only take a minute. Literally. Learn how to install safely at nest.com/ca/setup/nestcam

More information

Corrosion Data Management Software Version 3.1.3

Corrosion Data Management Software Version 3.1.3 Corrosion Data Management Software Version 3.1.3 Metal Samples Corrosion Monitoring Systems A Division of Alabama Specialty Products, Inc. 152 Metal Samples Road, Munford, AL 36268 Phone: 256-358-4202

More information

Altiris Patch Management Solution for Windows 7.6 from Symantec Third-Party Legal Notices

Altiris Patch Management Solution for Windows 7.6 from Symantec Third-Party Legal Notices Appendix A Altiris Patch Management Solution for Windows 7.6 from Symantec Third-Party Legal Notices This appendix includes the following topics: Third-Party Legal Attributions CabDotNet MICROSOFT PLATFORM

More information

Guía de instalación rápida. TEG-S16g TEG-S24g 1.01

Guía de instalación rápida. TEG-S16g TEG-S24g 1.01 Guía de instalación rápida TEG-S16g TEG-S24g 1.01 Table of Contents Español 1 1. Antes de iniciar 1 2. Instalación del Hardware 2 3. LEDs 3 Technical Specifications 4 Troubleshooting 5 Version 01.12.2011

More information

CobraNet TM User s Manual

CobraNet TM User s Manual CobraNet TM User s Manual 19201 Cook Street, Foothill Ranch, CA 92610-3501 USA Phone: (949) 588-9997 Fax: (949) 588-9514 Email: sales@renkus-heinz.com Web: www.renkus-heinz.com CobraNet TM is a registered

More information

Sun Enterprise Optional Power Sequencer Installation Guide

Sun Enterprise Optional Power Sequencer Installation Guide Sun Enterprise Optional Power Sequencer Installation Guide For the Sun Enterprise 6500/5500 System Cabinet and the Sun Enterprise 68-inch Expansion Cabinet Sun Microsystems, Inc. 901 San Antonio Road Palo

More information

4x3.5" Hot-Swap Drive Cage Kit Installation Guide for Intel Server Chassis/System

4x3.5 Hot-Swap Drive Cage Kit Installation Guide for Intel Server Chassis/System 4x3.5" Hot-Swap Drive Cage Kit Installation Guide for Intel Server Chassis/System Order Number: G23758-002 G23758-002 This document provides instructions for installing the following accessory kit: FUP4X35HSDK

More information

RDC-7 Windows XP Installation Guide

RDC-7 Windows XP Installation Guide RDC-7 Windows XP Installation Guide CONTENTS 1. End User License Agreement...3 2. Important notes...4 3. Customer support...4 4. Installing the USB driver...4 I. Prior to installation...4 II. Installation

More information

Solaris 10 Documentation README

Solaris 10 Documentation README Solaris 10 Documentation README Sun Microsystems, Inc. 4150 Network Circle Santa Clara, CA 95054 U.S.A. Part No: 817 0550 10 January 2005 Copyright 2005 Sun Microsystems, Inc. 4150 Network Circle, Santa

More information

80PK-27 SureGrip TM Industrial Surface Temperature Probe

80PK-27 SureGrip TM Industrial Surface Temperature Probe 80PK-27 SureGrip TM Industrial Surface Temperature Probe XWWarning Instruction Sheet To avoid electrical shock, do not use this probe when voltages exceeding 24 V ac rms or 60 V dc are present. The probe

More information

Instruction Sheet PDS SERIES. Single Circuit Power Sequencer FRONT VIEW POWER ON I. DOWN 120V 12A 60Hz REAR VIEW. (PDS-615R Shown)

Instruction Sheet PDS SERIES. Single Circuit Power Sequencer FRONT VIEW POWER ON I. DOWN 120V 12A 60Hz REAR VIEW. (PDS-615R Shown) Instruction Sheet PDS SERIES Single Circuit Power Sequencer FRONT VIEW POWER ON I SEQUENCE SYSTEM OFF 120V-12A-60Hz UNSWITCHED STATUS REMOTE 5 6 CLOSED - All channels on OPEN - All channels off UP COM

More information

User Guide. LXX35-LED Light Source. Luxxor LXX35-LED User Guide. Contents

User Guide. LXX35-LED Light Source. Luxxor LXX35-LED User Guide. Contents User Guide Luxxor LXX35-LED User Guide LXX35-LED Light Source Contents Symbol Descriptions... 3 Set Up... 6 Operation... 8 Mounting... 9 Cleaning... 10 Troubleshooting... 10 Ratings & Specifications...

More information

5-Port Gigabit GREENnet Switch TEG-S5g ŸGuía de instalación rápida (1) ŸTechnical Specifications (3) ŸTroubleshooting (4)

5-Port Gigabit GREENnet Switch TEG-S5g ŸGuía de instalación rápida (1) ŸTechnical Specifications (3) ŸTroubleshooting (4) 5-Port Gigabit GREENnet Switch TEG-S5g ŸGuía de instalación rápida (1) ŸTechnical Specifications (3) ŸTroubleshooting (4) 2.02 1. Antes de iniciar Contenidos del paquete ŸTEG-S5g ŸGuía de instalación rápida

More information

Altiris Patch Management Solution for Windows 7.5 SP1 from Symantec Third-Party Legal Notices

Altiris Patch Management Solution for Windows 7.5 SP1 from Symantec Third-Party Legal Notices Appendix A Altiris Patch Management Solution for Windows 7.5 SP1 from Symantec Third-Party Legal Notices This appendix includes the following topics: Third-Party Legal Attributions CabDotNet XML-RPC.NET

More information

Quick-Start Guide. Arrival Sensor

Quick-Start Guide. Arrival Sensor Quick-Start Guide Arrival Sensor Meet your Arrival Sensor The Arrival Sensor lets you stay connected to people, pets, and cars by sending you a push notification when they arrive and leave home. How to

More information

ENGLISH FRANÇAIS DEUTSCH ESPAÑOL ÐÓÑÑÊÈÉ

ENGLISH FRANÇAIS DEUTSCH ESPAÑOL ÐÓÑÑÊÈÉ ÐÓÑÑÊÈÉ ESPAÑOL DEUTSCH FRANÇAIS ENGLISH ÐÓÑÑÊÈÉ ESPAÑOL DEUTSCH FRANÇAIS ENGLISH ÐÓÑÑÊÈÉ ESPAÑOL DEUTSCH FRANÇAIS ENGLISH ÐÓÑÑÊÈÉ ESPAÑOL DEUTSCH FRANÇAIS ENGLISH ÐÓÑÑÊÈÉ ESPAÑOL DEUTSCH FRANÇAIS ENGLISH

More information

READ AND FOLLOW ALL SAFETY INSTRUCTIONS 1. DANGER RISK OF SHOCK DISCONNECT POWER BEFORE INSTALLATION

READ AND FOLLOW ALL SAFETY INSTRUCTIONS 1. DANGER RISK OF SHOCK DISCONNECT POWER BEFORE INSTALLATION UR Series LED Upgrade Kit Includes: 48" Linear Option IMPORTANT SAFEGUARDS When using electrical equipment, basic safety precautions should always be followed including the following: READ AND FOLLOW ALL

More information

AC ADAPTOR AC-550CE. MAINTENANCE MANUAL 1st Edition Serial No. 45451 and Higher

AC ADAPTOR AC-550CE. MAINTENANCE MANUAL 1st Edition Serial No. 45451 and Higher AC ADAPTOR AC-550CE MAINTENANCE MANUAL 1st Edition Serial No. 45451 and Higher WARNING This manual is intended for qualified service personnel only. To reduce the risk of electric shock, fire or injury,

More information

USB 2.0 VGA ADAPTER USER MANUAL

USB 2.0 VGA ADAPTER USER MANUAL USB 2.0 VGA ADAPTER USER MANUAL CONTENTS INTRODUCTION... 3 FEATURES... 3 SYSTEM REQUIREMENTS... 3 PACKAGE CONTENTS... 3 SUPPORTED COMMON DISPLAY RESOLUTION... 4 TECHNICAL SPECIFICATIONS... 4 INSTALLATION

More information

Magnum 224 LTO Library, StorageLibrary T24, or StorageLoader 2U LTO RIGHT LEFT. Shipping locks

Magnum 224 LTO Library, StorageLibrary T24, or StorageLoader 2U LTO RIGHT LEFT. Shipping locks RIGHT Magnum 224 LTO Library, StorageLibrary T24, or StorageLoader 2U LTO Accessories These accessories are included with your library LEFT Power cords LVD SCSI 68-pin HD to HD cable and LVD terminator*

More information

Lumencor SOLA light engine Instruction Manual

Lumencor SOLA light engine Instruction Manual Lumencor SOLA light engine Instruction Manual Lumencor, Inc. 14964 NW Greenbrier Parkway, Beaverton, OR 97006 T 503.213.4269 F 503.536.6741 www.lumencor.com Emissions Certifications This equipment has

More information

Linksys Business Series 24-port Gigabit Ethernet Switch

Linksys Business Series 24-port Gigabit Ethernet Switch QUICK INSTALLATION GUIDE Linksys Business Series 24-port Gigabit Ethernet Switch Model SGE2000 1 2 Install: Desktop Linksys Business Series SGE2000 Gibabit Ethernet Switch TM Install: Wall 3 140988 TM

More information

Quick Installation Guide. Guía de instalación rápida. Wireless 150 N USB Adapter W150NU

Quick Installation Guide. Guía de instalación rápida. Wireless 150 N USB Adapter W150NU Quick Installation Guide Guía de instalación rápida Wireless 150 N USB Adapter W150NU V1 Contents Español 1 1. Antes de iniciar 2. Cómo se instala 1 2 3. Cómo usar el adaptador inalámbrico 4 Troubleshooting

More information

Sun StorEdge RAID Manager 6.2.21 Release Notes

Sun StorEdge RAID Manager 6.2.21 Release Notes Sun StorEdge RAID Manager 6.2.21 Release Notes formicrosoftwindowsnt Sun Microsystems, Inc. 901 San Antonio Road Palo Alto, CA 94303-4900 USA 650 960-1300 Fax 650 969-9131 Part No. 805-6890-11 November

More information

ONLINE LAUNCHER. Choose one of the following: RADEON Products. HydraVision. Compliance Information

ONLINE LAUNCHER. Choose one of the following: RADEON Products. HydraVision. Compliance Information ONLINE LAUNCHER Choose one of the following: RADEON Products HydraVision RADEON Products RADEON 9800 Series RADEON 9600 Series RADEON 9200 Series FCC This device complies with FCC Rules Part 15. Operation

More information

Compact I/O End Caps/Terminators

Compact I/O End Caps/Terminators Installation Instructions Compact I/O End Caps/Terminators Catalog Numbers 1769-ECL, 1769-ECR Topic Page Important User Information 2 Environment and Enclosure 3 North American Hazardous Location Approval

More information

5-Port 10/100Mbps Fast Ethernet Switch (TE100-S5) 8-Port 10/100Mbps Fast Ethernet Switch (TE100-S8)

5-Port 10/100Mbps Fast Ethernet Switch (TE100-S5) 8-Port 10/100Mbps Fast Ethernet Switch (TE100-S8) 5-Port 10/100Mbps Fast Ethernet Switch (TE100-S5) 8-Port 10/100Mbps Fast Ethernet Switch (TE100-S8) ŸGuía de instalación rápida (1) ŸTechnical Specifications [3] ŸTroubleshooting (4) 1.22 1. Antes de iniciar

More information

NortechCommander Software Operating Manual MAN-00004 R6

NortechCommander Software Operating Manual MAN-00004 R6 NortechCommander Software Operating Manual MAN-00004 R6 If the equipment described herein bears the symbol, the said equipment complies with the applicable European Union Directive and Standards mentioned

More information

Intel Device View. User Guide

Intel Device View. User Guide Intel Device View User Guide Year 2000 Capable An Intel product, when used in accordance with its associated documentation, is Year 2000 Capable when, upon installation, it accurately stores, displays,

More information

EPSON Scan Server & EPSON TWAIN Pro Network

EPSON Scan Server & EPSON TWAIN Pro Network EPSON Scan Server & EPSON TWAIN Pro Network EPSON Scan Server & EPSON TWAIN Pro Network SCANNER UTILITY PROGRAMS All rights reserved. No part of this publication may be reproduced, stored in a retrieval

More information

Sense. 3D Scanner. User Guide. See inside for use and safety information.

Sense. 3D Scanner. User Guide. See inside for use and safety information. Sense 3D Scanner User Guide See inside for use and safety information. 1 CONTENTS INTRODUCTION.... 3 IMPORTANT SAFETY INFORMATION... 4 Safety Guidelines....4 SENSE 3D SCANNER FEATURES AND PROPERTIES....

More information

MADRIX NEO Quick Start Guide & User Manual

MADRIX NEO Quick Start Guide & User Manual MADRIX NEO Quick Start Guide & User Manual 4 th Edition, Last Update: March 2011 Thank You for Purchasing MADRIX NEO Please read this manual carefully and thoroughly before using the MADRIX NEO. Make sure

More information

Smart Remote. with. QuickGuide

Smart Remote. with. QuickGuide Smart Remote with QuickGuide 1 1 2 3 2 A B 3 A Connecting the remote control B Do not cover the microphone 1 Adjusting the volume Press the + or - button. 2 Controlling audio functions Press the button

More information

ASUS Miracast Dongle E-MANUAL E8741

ASUS Miracast Dongle E-MANUAL E8741 E-MANUAL E8741 E8741 First Edition November 2013 COPYRIGHT INFORMATION No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in

More information

Ready. Set. Go. Pick a spot and plug it in.

Ready. Set. Go. Pick a spot and plug it in. Ready. Set. Go. Pick a spot and plug it in. Download the Nest app for Android or ios and follow the simple setup instructions. It should only take a minute. Literally. Learn how to install safely at nest.com/setup/nestcam

More information

Backup Scanner Module

Backup Scanner Module Backup Scanner Module Catalog Number 1747-BSN Installation Instructions 2 Backup Scanner Module Important User Information Because of the variety of uses for the products described in this publication,

More information

FortiFone QuickStart Guide for FON-670i and FON-675i

FortiFone QuickStart Guide for FON-670i and FON-675i FortiFone QuickStart Guide for FON-670i and FON-675i FortiFone QuickStart Guide for FON-670i and FON-675i Revision 2 September 25, 2015 Copyright 2015 Fortinet, Inc. All rights reserved. Fortinet, FortiGate,

More information

X73 Scan/Print/Copy. Getting Started. March 2001.

X73 Scan/Print/Copy. Getting Started. March 2001. X73 Scan/Print/Copy Getting Started March 2001 www.lexmark.com Edition: March 2001 The following paragraph does not apply to any country where such provisions are inconsistent with local law: LEXMARK INTERNATIONAL,

More information

SunFDDI 6.0 on the Sun Enterprise 10000 Server

SunFDDI 6.0 on the Sun Enterprise 10000 Server SunFDDI 6.0 on the Sun Enterprise 10000 Server Sun Microsystems, Inc. 901 San Antonio Road Palo Alto, CA 94303-4900 USA 650 960-1300 Fax 650 969-9131 Part No.: 806-3610-11 November 1999, Revision A Send

More information

1545 Bar Code Laser Scanner

1545 Bar Code Laser Scanner User s Guide 1545 Bar Code Laser Scanner P/N 057286-003 6001 36th Avenue West PO Box 4280 Everett, WA 98203-9280 Phone (206) 348-2600 P/N 057286-003 This device meets Class B limit requirements of CISPR

More information

INVENTEK SYSTEMS ISM34x-USB Embedded Serial-to-WiFi Module es-wifi 802.11 a/b/g/n, Bluetooth 4.0, NFC

INVENTEK SYSTEMS ISM34x-USB Embedded Serial-to-WiFi Module es-wifi 802.11 a/b/g/n, Bluetooth 4.0, NFC INVENTEK SYSTEMS ISM34x-USB Embedded Serial-to-WiFi Module es-wifi 802.11 a/b/g/n, Bluetooth 4.0, NFC Preliminary Data Sheet Page 1 Table of Contents 1 GENERAL DESCRIPTION... 3 2 PART NUMBER DETAIL DESCRIPTION...

More information

500/600/1000. User Manual June 2011 Rev. 061311. 1 v061311

500/600/1000. User Manual June 2011 Rev. 061311. 1 v061311 500/600/1000 User Manual June 2011 Rev. 061311 1 v061311 http://shopping.netsuite.com/digitalcheck TABLE OF CONTENTS Contents Radio Frequency Interference... 3 About the SB Scanner... 3 SB Scanner Equipment...

More information

iosafe Solo External Hard Drive

iosafe Solo External Hard Drive Users Manual & Limited Warranty iosafe Solo External Hard Drive USB 2.0 Fireproof Waterproof FloSafe Cooling Technology Data Recovery Service 910-10841-00 REV 7.1 2 COPYRIGHTS Copyright iosafe, Inc. 2009.

More information

10BASE-T/100BASE-TX & 100BASE-FX 2-Port Bridging Media Converter

10BASE-T/100BASE-TX & 100BASE-FX 2-Port Bridging Media Converter 12 COMPLIANCE INFORMATION UL Listed C-UL Listed (Canada) CISPR22/EN55022 Class A + EN55024 CE Mark FCC Regulations This equipment has been tested and found to comply with the limits for a class A digital

More information

LOGOBOOK GUIDELINES & RULES

LOGOBOOK GUIDELINES & RULES RUB PEOPLE THINK LEAN R LOGOBOOK GUIDELINES & RULES R A logo is a graphic mark or emblem commonly used by commercial enterprises, organizations and even individuals to aid and promote instant public recognition.

More information

ZigBee Extender 3. Features. Supported Models and Requirements. Important Safety Instructions. What Is Included: Specifications

ZigBee Extender 3. Features. Supported Models and Requirements. Important Safety Instructions. What Is Included: Specifications ZigBee Extender 3 Features The Card Access ZigBee Extender 3 operates as a ZigBee (IEEE 802.15.4) router and mesh extender. The Extender is designed to improve ZigBee signal latency that can occur when

More information

ET0101-VF1&VF2 User manual ET0101-VF1/VF2 User Manual

ET0101-VF1&VF2 User manual ET0101-VF1/VF2 User Manual ET0101-VF1/VF2 User Manual www.solidview.com Contact: sales@solidview.com 1 Thank you for purchasing this product. For optimum performance and safety, please read these instructions carefully before connecting,

More information

Como sabemos que lo funcional y lo estético son importantes para ti, te ofrecemos diferentes acabados y colores.

Como sabemos que lo funcional y lo estético son importantes para ti, te ofrecemos diferentes acabados y colores. A En Rejiplas fabricamos y comercializamos organizadores y soluciones de espacio para el hogar. Hacemos realidad tus proyectos e ideas optimizando todos los ambientes. Nuestros herrajes y soluciones están

More information

EG REACH Information für besonders besorgniserregenden Stoffe der Kandidatenliste

EG REACH Information für besonders besorgniserregenden Stoffe der Kandidatenliste EU REACH SVHC Disclosure on Candidate List REACH (Registration, Evaluation, Authorization and Restriction of Chemicals, EC 1907/2006) is the European Union s (EU) chemical substances regulatory framework.

More information

Quick Installation Guide TK-209K TK-409K

Quick Installation Guide TK-209K TK-409K Quick Installation Guide TK-209K TK-409K Table of of Contents Contents English... 1. Before You Start... 2. How to Connect... 3. Operation... 1 1 2 4 Troubleshooting... 5 Version 03.16.2007 1. Before You

More information

Veritas Storage Foundation 5.0 Software for SPARC

Veritas Storage Foundation 5.0 Software for SPARC Veritas Storage Foundation 5.0 Software for SPARC Release Note Supplement Sun Microsystems, Inc. www.sun.com Part No. 819-7074-10 July 2006 Submit comments about this document at: http://www.sun.com/hwdocs/feedback

More information

Quick Installation Guide

Quick Installation Guide Quick Installation Guide TEW-432BRP H/W: v.d1.0r Table of Contents... 1 1. Before You Start... 1 2. Install Router... 2 3. Replacing an existing router... 5 4. Adding the router behind an existing router...

More information

Quick Installation Guide TV-IP422 TV-IP422W H/W: A1.0R

Quick Installation Guide TV-IP422 TV-IP422W H/W: A1.0R Quick Installation Guide TV-IP422 TV-IP422W H/W: A1.0R Table Table of Contents of Contents... 1 1. Before You Start... 1 2. Hardware Installation... 3 3. Configure the Internet Camera... 4 Troubleshooting...

More information

SUBCHAPTER A. AUTOMOBILE INSURANCE DIVISION 3. MISCELLANEOUS INTERPRETATIONS 28 TAC 5.204

SUBCHAPTER A. AUTOMOBILE INSURANCE DIVISION 3. MISCELLANEOUS INTERPRETATIONS 28 TAC 5.204 Part I. Texas Department of Insurance Page 1 of 10 SUBCHAPTER A. AUTOMOBILE INSURANCE DIVISION 3. MISCELLANEOUS INTERPRETATIONS 28 TAC 5.204 1. INTRODUCTION. The commissioner of insurance adopts amendments

More information

JTAGjet. series SIGNUM SYSTEMS CORPORATION. USB 2.0 Driver for JTAGjet and ADM51. Installation Instructions

JTAGjet. series SIGNUM SYSTEMS CORPORATION. USB 2.0 Driver for JTAGjet and ADM51. Installation Instructions JTAGjet series SIGNUM SYSTEMS CORPORATION USB 2.0 Driver for JTAGjet and ADM51 Installation Instructions COPYRIGHT NOTICE Copyright (c) 2011 by Signum Systems Corporation. All rights are reserved worldwide.

More information

Waterproof Bluetooth Speaker

Waterproof Bluetooth Speaker TM Waterproof Bluetooth Speaker Printed in China Part No. 480-933-P Version A CWA BT310 Product Information Guide PRODUCT FEATURES FRONT VIEW LED Light Speaker Mesh TOP VIEW Volume Down Loudspeakers Volume

More information

NÜVO REVO 270. 900 mm 810 x 810 x (660-860) No. Description

NÜVO REVO 270. 900 mm 810 x 810 x (660-860) No. Description REVO 70 Use these instructions for the following items / Suivez ces instructions pour les items suivants -7-4 007 Cabinet / Caisson Size / Dimension 900 mm 0 x 0 x (660-60) No. Description Qty / Qté. Upper

More information

RIGOL. Quick Guide. DS1000CA Series Oscilloscope. Aug. 2011. RIGOL Technologies, Inc.

RIGOL. Quick Guide. DS1000CA Series Oscilloscope. Aug. 2011. RIGOL Technologies, Inc. Quick Guide DS1000CA Series Oscilloscope Aug. 2011 Technologies, Inc. Guaranty and Declaration Copyright 2011 Technologies, Inc. All Rights Reserved. Trademark Information is a registered trademark of

More information

IPC-610. Industrial PC Chassis

IPC-610. Industrial PC Chassis IPC-610 Industrial PC Chassis Copyright Notice This document is copyrighted, September 1998, by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right to make improvements

More information

Safety, Installation and Operating Instructions Instructions importantes concernant la sécurité

Safety, Installation and Operating Instructions Instructions importantes concernant la sécurité Safety, Installation and Operating Instructions Instructions importantes concernant la sécurité Manual for the Following Battery Charger Models i2412, i3612, i4809, i2425, i3625, and i4818 081808 IMPORTANT

More information

ZoomText 10. Usuario Guía

ZoomText 10. Usuario Guía ZoomText 10 Usuario Guía Copyrights Magnificador ZoomText Copyright 2011, Algorithmic Implementations, Inc. Todos los derechos reservados. Magnificador/Lector ZoomText Copyright 2011, Algorithmic Implementations,

More information

Duplex ID Card & License Scanner. User Guide

Duplex ID Card & License Scanner. User Guide Duplex ID Card & License Scanner User Guide CE Conformity and FCC Statement This equipment has been tested and found to comply with the limits of the European Council Directive on the approximation of

More information

GX-2009 Data Logger Management Program Operator s Manual

GX-2009 Data Logger Management Program Operator s Manual GX-2009 Data Logger Management Program Operator s Manual Part Number: 71-0163RK Revision: C Released: 3/19/12 www.rkiinstruments.com Warranty RKI Instruments, Inc. warrants gas alarm equipment sold by

More information

Quick Installation Guide. 1000Base-SX/LX Fiber Converters

Quick Installation Guide. 1000Base-SX/LX Fiber Converters Quick Installation Guide Base-SX/LX Fiber Converters Table Table of Contents of Contents English... 1. Before You Start... 2. Hardware Installation... 1 1 2 Spefications... Ordering Information... Troubleshooting...

More information

8800 Series 100-240VAC PSU XCM88PS1

8800 Series 100-240VAC PSU XCM88PS1 8800 Series 100-240VAC PSU XCM88PS1 Hardware Installation Guide 350 East Plumeria Drive San Jose, CA 95134 USA February 2011 201-13472-02 1.0 2011 NETGEAR, Inc. All rights reserved. No part of this publication

More information

BMW Multi Tool User Manual

BMW Multi Tool User Manual X-Horse Electronics Co., Ltd. Table of Contents 1. Safety Precautions and Warnings... 3 2. General Information... 4 3. Hardware Overview... 5 3.1. Tool Description... 5 3.2. Specifications... 6 3.3. System

More information

Read this document before using this product.

Read this document before using this product. VistaMAX Series Safety Precautions Read this document before using this product. Download and read the full user manual for complete information (see the VistaMAX Support File Access document for download

More information

Work Instruction (Instruccion de Trabajo) Wistron InfoComm (Texas) Corp.

Work Instruction (Instruccion de Trabajo) Wistron InfoComm (Texas) Corp. Effective Date: 8/1/2011 Page 1 of 6 Description: (Descripción) 1.0 Purpose (Objetivo) 2.0 Scope (Alcance) 3.0 Fixture List (Lista de Materiales) 4.0 Activities (Actividades) Prepared By: Daniel Flores

More information

SUBCHAPTER A. AUTOMOBILE INSURANCE DIVISION 3. MISCELLANEOUS INTERPRETATIONS 28 TAC 5.204

SUBCHAPTER A. AUTOMOBILE INSURANCE DIVISION 3. MISCELLANEOUS INTERPRETATIONS 28 TAC 5.204 Part I. Texas Department of Insurance Page 1 of 11 SUBCHAPTER A. AUTOMOBILE INSURANCE DIVISION 3. MISCELLANEOUS INTERPRETATIONS 28 TAC 5.204 1. INTRODUCTION. The Texas Department of Insurance proposes

More information

Intel RAID Premium Feature Key AXXRPFKSSD, AXXRPFKDE, and AXXRPFKSNSH Installation Guide

Intel RAID Premium Feature Key AXXRPFKSSD, AXXRPFKDE, and AXXRPFKSNSH Installation Guide Intel RAID Premium Feature Key AXXRPFKSSD, AXXRPFKDE, and AXXRPFKSNSH Installation Guide Order Number: E88588-001 E88588-001 IMPORTANT: Your Intel RAID Controller must be programmed with the latest Intel

More information

Travaux publics et Services gouvernementaux Canada. Title - Sujet Scanner Doppler Lidar. Solicitation No. - N de l'invitation K8D22-160161/A

Travaux publics et Services gouvernementaux Canada. Title - Sujet Scanner Doppler Lidar. Solicitation No. - N de l'invitation K8D22-160161/A Public Works and Government Services Canada Travaux publics et Services gouvernementaux Canada 1 1 RETURN BIDS TO: RETOURNER LES SOUMISSIONS À: Travaux publics et Services gouvernementaux Canada Place

More information

BrightStor ARCserve Backup for Windows

BrightStor ARCserve Backup for Windows BrightStor ARCserve Backup for Windows Tape RAID Option Guide r11.5 D01183-1E This documentation and related computer software program (hereinafter referred to as the "Documentation") is for the end user's

More information

DA/ROT 350* Reload Housing

DA/ROT 350* Reload Housing Technical Data Specifications DA/ROT 350* Reload Housing (A350-00) Housing Technical Data Données Techniques relatives aux De DA/ROT 350 Gaines Technische Daten DA/ROT 350 Gehäuse Especificaciones de Datos

More information

Technical Service Bulletin

Technical Service Bulletin Technical Service Bulletin FILE CONTROL CREATED DATE MODIFIED DATE FOLDER OpenDrive 02/05/2005 662-02-25008 Rev. : A Installation Licence SCO sur PC de remplacement English version follows. Lors du changement

More information

Inspection des engins de transport

Inspection des engins de transport Inspection des engins de transport Qu est-ce qu on inspecte? Inspection des engins de transport Inspection administrative préalable à l'inspection: - Inspection des documents d'accompagnement. Dans la

More information

IntesisBox PA-RC2-xxx-1 SANYO compatibilities

IntesisBox PA-RC2-xxx-1 SANYO compatibilities IntesisBox PA-RC2-xxx-1 SANYO compatibilities In this document the compatible SANYO models with the following IntesisBox RC2 interfaces are listed: / En éste documento se listan los modelos SANYO compatibles

More information

SNQ-60x0-320 Series Data Center Switch. Quick Installation Guide

SNQ-60x0-320 Series Data Center Switch. Quick Installation Guide Introduction This guide is to assist the reader with the most basic form of installation and connection to switches in this series. As there is more than one switch in this series, the diagrams might slightly

More information