CHAPTER 11 UNIVERSITY OF FLORIDA
|
|
- Charlotte Brooks
- 8 years ago
- Views:
Transcription
1 CHAPTER 11 UNIVERSITY OF FLORIDA College of Engineering Department of Aerospace Engineering, Mechanics, and Engineering Science Gainesville, Florida Principle Investigator: Robert 1. Hi&o (904)
2 168 NSF 1995 Engineering Senior Design Projects to Aid the Disabled One-Arm Wheelchair Control System Designers: Mark Dallara Supervising ProJesor: Roberf J. Hirko Ph.D., Ali A. Seireg Ph.D. Aerospace Engineering, Mechanics, and Engineering Science Gainesville, FL INTRODUCTION Propelling a non-electric wheelchair is typically a two-handed effort, especially when straight-line motion is involved. This presents a problem to wheelchair users with functional use of only one hand. Alfred, 76, suffered a stroke 15 years ago that left him partially paralyzed on the left side of his body. He can walk short distances with the aid of a quad-cane, but uses a wheelchair frequently indoors and outdoors. Using a normal wheelchair poses problems, from moving away from the kitchen table to maneuvering across the living room. The One-Arm Wheelchair is designed to allow Alfred to move the wheelchair in a straight line with one hand, but also allow turning motion when necessary. A lightweight wheelchair is modified by the addition of an aluminum torque-transfer mechanism that contacts the wheels of the chair with two small rubber wheels. A handle next to the right armrest allows the patient to engage the mechanism for straight-line movement, or disengage the mechanism for turning. The device separates and folds out of the way when the chair is collapsed. The chair with control lever and one drive wheel is shown in Figure 11.l. SUMMARY OF IMPACT The wheelchair is intended primarily for indoor use, but also for occasional outdoor use. The following design criteria are established for the chair:. a lightweight mechanism design which does not interfere with collapsibility of the chair. straight line and turning movements enabled when required These criteria are accomplished and it did not take long for Alfred to learn how to manipulate the devices. The overall benefit seen from this chair is that Figure 11.I. Chair for One-Arm Operation. Alfred has a much greater degree of control over his position while he is in the wheelchair. The chair and modifications collapse to fit into the tnmk of a car when needed for outdoor use. Propulsion by a second individual is not impeded by the mechanism, so the device may remain in its unfolded state when the chair is not being moved by the occupant. TECHNICAL DESCRIPTION A pair of formed aluminum bars comprise the supports for the device. They are attached to the seat handlebars at the top, and to blocks clamped onto the wheelchair frame at the bottom, as seen in Figure The right-hand support is directly connected to a bearing housing which may be rotated slightly to engage or disengage the rubber wheel on the right. Another aluminum bar connects the right side of the bearing housing and to an over-the-center lock on the block clamped below (Figure 11.3). This lock is controlled by a handlebar that the chair occupant moves to engage the wheel as is demonstrated in Figure 11.l. The torque transfer system consists of rubber wheels
3 Chanter 11: Universitv of Florida 169 attached to aluminum rods in bearings, with hexagonal sockets and a section of hexagonal rod between the two halves of the transfer. They can be seen disconnected in Figure 11.2 and connected in Figure By pulling back slightly on the pins set into the hexagonal bar, the left side of the transfer may be disconnected and rotated so that it is parallel with the seat back bar of the wheelchair frame, and thus out of the way. When the mechanism is disconnected in this manner, the chair may be collapsed in the normal fashion for transportation. Figure Drive Assembly. Figure Rear View of Mechanism, disconnected.
4 170 NSF 1995 Engineering Senior Design Projects to Aid the Disabled RETRACTABLE FOOT SUPPORTS FOR A SHOWER CHAIR Designer: Elizabeth C. Phillips Client Coordinator: Mark Frasier, Sunland at Gainesville Supervising Pr@ssor: Robert J. Hirko, Ph.D. Aerospace Engineering, Mechanics, and Engineering Scieme Gainesville, FL 3261 l-6250 INTRODUCTION For individuals requiring full-time use of wheelchairs, bathing and personal grooming can be a difficult challenge. Shower/toilet chairs are used for this reason. The problem with these types of chairs is that they have no place for individuals to place their feet. Consequently, some individuals may tend to straighten their legs in a rigid posture making attendant care nearly impossible. The purpose of this project is to provide foot supports that are able to withstand repetitive loading and also be resistant to exposure to moist environments. The supports should also retract so that they do not interfere with transport to and from the shower chair and wheelchairs. SUMMARY OF IMPACT A local care facility for severely developmentally disabled individuals supplied the chair for modification. As can be seen in Figure 11.4, the foot rests are easily bolted on to the frame at the front wheel positions. This chair became a great aid to attendants at the facility for transport to, from, and in the shower. Making care giving easier as a natural result also made more care available to those who needed it in the facility, since caregivers are less reluctant to attempt showering the clients. Figure Foot Supports on Toilet Chair
5 Chapter 11: University of Florida 171 TECHNICAL DESCRIPTION Each foot support consists of a three-piece mounting block, a rotating arm, and a 90-degree rotating food plate taken from a wheelchair. The mounting block is fitted to a currently used shower/toilet chair. Figure 11.4 shows the first prototype in a fully extended position, and Figure 11.5 shows the fully retracted position. The mounting block is made of aluminum and held together by lo-32 screws. The arm is made of 1 square stainless steel tubing and rotates from the extended forward position to the rear stop on the clamp out of the way of an individuals feet. Square tubing is used to prevent lateral arm rotation that is a common problem with the currently used wheelchair foot supports. A sleeve with a cylindrical rod welded to the front fits over the rotating arm and may be adjusted for height variation using a locking pin. These pin and adjustment holes can be seen in Figure The round rod provides for the mounting of a footplate. A standard footplate from a wheelchair is used for easy access of replaceable parts. The aluminum parts are treated with alodine, and the stainless steel parts are painted to prevent corrosion. In this way, these retractable foot supports make bathing and transportation to and from a wheelchair an easier task. Detailed drawings are available on request. Figure Supports retracted.
6 172 NSF 1995 Engineering Senior Design Projects to Aid the Disabled Battery Powered Door Opening Device Designer: Pablo Samsing Supervising Professor: Robert J. Hirko, Ph.D. Aerospace Engineering, Mechanics, and Engineering Science Gainesville, FL 3261 l-6250 INTRODUCTION A door-opening device is necessary for people lacking the strength to open doors. This is a problem for people who are ambulatory with walkers or canes, as well as for those in wheelchairs. The battery-powered door opening device, BPDOP, is activated by applying a downward pressure to the handle. Its drive is shown without its cover in Figure Additionally the device can provide support for the user. It can also be designed for use by someone in a wheelchair. Figure Drive Unit Without Cover. SUMMARY OF IMPACT The daily activities of people with disabilities, specifically lacking the strength to open doors, is complicated by the lack of doors with the ability to open automatically. The project that is designed is used for almost any application with the requirement that the operator be able to turn the handle to unlatch the door. Operators with the obstacles of pressurized doors or large doors will be able to overcome them and gain more accessibility. The primary goal of this device is to decrease the dependence on facilities to be equipped with automatic doors. TECHNICAL DESCRIPTION Requirements that are applied for the design of this door-opening device are as follows. First, weight of the device is kept in mind when designing and choosing materials. The BPDOP needed to be lightweight in order that it may also be used as a cane and carried around as such. The main body of the BPDOP is aluminum that is lightened by removing material that is structurally not necessary. The wheels are made of lightweight foam, with a plastic center. Two wheels, located at the front, transferred the force to move the device and another two wheels, located on the bumper, acted as push-rollers. The entire main body is covered with a toy lexan replica of a truck and attached to the unit by plastic screws with wing nuts, for ease of removal. The rest of the device, which consisted of the cane and handle, are made of aluminum and plastic, respectively. The BPDOP is intended to be used daily. In order to maintain the usability of the device, a rechargeable battery is used as the source of power. The advantages of using a battery are its ease of recharging and installation along with its small size. The motor and gear set up that powered the motor came from a modified Makita angle drill (Figure 11.7). The battery, located at the top of the cane, can be easily changed and replaced with a recharged battery. The application of the BPDOP required that it be easy to use with very little physical requirements. The unit is designed for a person with limited strength and dexterity. The only requirement, aside from being able to walk and carry the unit, is that the user be able to transfer his/her weight. The unit is activated by applying pressure to the handle. The handle is installed at a ninety degree angle from the cane (Figure 11.8) so that the unit will be activated by the user simply leaning into the cane. When the user leans into the cane, the trigger is pushed by a spring-loaded trailing wheel, located behind the unit. The handle can also be adjusted for users of different heights by
7 Chapter 11: University of Florida 173 just turning it counter-clockwise, moving the handle up or down on the cane and then tightening it by turning the handle clock-wise. The unit is designed to be affordable by using inexpensive materials. The cost of the materials of a single unit is about $270. Figure Drive Unit and Similar Drill Motor. Figur-e Entire Unit With Cover.
8
Rating when used as a weight carrying hitch without spring bars:
BOLT-TOGETHER WEIGHT DISTRIBUTING HITCH SYSTEM Rating when used as a weight distributing hitch with spring bars: Part Number 48051 4805 48053 48054 Max Tongue Weight 550 Ibs. 750 Ibs. 1000 Ibs. 1400 lbs.
More informationOwner s Manual Read and keep this manual. Patents World Wide
Owner s Manual Read and keep this manual. Patents World Wide S & S Industries, Inc., Sarasota, FL, USA www.trail-gator.com Copyright 2008 All Rights Reserved The following manual is provided to assist
More informationBODY-12, Door Handle - Removal, Installation, and Adjustment
Introduction BODY-12, Door Handle - Removal, Installation, and Adjustment There are many different procedures floating around describing how to replace the door handles on a 944 and every one of them will
More informationSLACK PERFORMANCE KARTS
SLACK PERFORMANCE KARTS SET UP GUIDE Thank you for purchasing a 2013 Slack Axiom Chassis. Performance Mfg. strives to provide you with the very best chassis and components on the market today. Your satisfaction
More informationFUTURE MOBILITY HEALTHCARE APPRECIATES YOUR BUSINESS. OUR CUSTOMER SERVICE REPRESENTATIVES CAN BE CONTACTED AT: TO PLACE ORDERS: (905) 671-1661
PARTS MANUAL FUTURE MOBILITY HEALTHCARE APPRECIATES YOUR BUSINESS. OUR CUSTOMER SERVICE REPRESENTATIVES CAN BE CONTACTED AT: TO PLACE ORDERS: (905) 671-1661 FOR YOUR CONVENIENCE YOU MAY ALSO PLACE ORDERS
More information1. Lay out 2 pieces of 7/8" tubing and mark for bending as shown. Remember that the bend is in the shaded area as shown below in Figure 1.
MINI BIKE PLANS Page 1 INTRODUCTION Before starting to build your Mini-Bike, be sure that you have all the parts shown on the material list. You will note that tubing has been used in the construction.
More informationAnatomy of a Manual Wheelchair
Anatomy of a Manual Wheelchair D. Michael McKeough, PT, EdD Associate Professor Division of Physical Therapy 1 Abstract This presentation illustrates the components of a manual wheelchair. Note pages contain
More informationSECTION G2: CABLE PROCESSOR MODULE MAINTENANCE
SECTION G2: CABLE PROCESSOR MODULE MAINTENANCE Cable Processor Module overview WARNING! When tipping the Cable Processor Module back, (after removing the toggle arm pin), use extreme caution not to drop
More informationTRANS-05, Torque Tube Removal, Rebuilding, and Installation
TRANS-05, Torque Tube Removal, Rebuilding, and Installation Tools Metric Wrench Set Metric Socket Set Jack Stands (6 minimum) Floor Jack 8mm Cheesehead socket (also referred to as 12 point internal socket
More information6 inch A-Arm Lift Kit WARNING: 16-018/16-019. installation instructions. will fit CLUB CAR DS. included:
Revised May 205 6-08/6-09 6 inch A-Arm Lift Kit will fit CLUB CAR DS installation instructions included: Rear Lift Blocks Main Suspension Assembly Spindles A-Arms Rear Shock Mounting Plates U-Bolts WARNING:
More informationMGB Chrome Bumper Conversion
MGB Chrome Bumper Conversion Installation Instructions For 1974 1/2-1980 MGB This kit requires cutting, welding, and painting. Professional installation recommended. Note: Every MGB body is slightly different
More informationIndications for a PMD as Reasonable and Necessary and Types of PMD Categories Available
Appendix K The face-to-face examination provides the clinical information needed to determine if a patient needs a Power Mobility Device (PMD) and what type of PMD may be needed. This information needs
More information2010 APPLICATION REFERENCE GUIDE
2010 APPLICATION REFERENCE GUIDE INDEX QUALITY POLICY 2 ERGO ASSIST STANDARD 4-13 CUSTOM 14-18 END EFFECTORS 19-24 LIFT ASSIST 25-41 FIXTURED TOOLS 42-53 FIXTURES 54-63 ASSEMBLY TABLES 64-72 CARTS/ DUNNAGE
More informationRollator Cane and Brake Replacement SAFETY SUMMARY (CONTINUED)
Rollator Cane and Replacement Assembly, Installation and Operating Instructions SAVE THESE INSTRUCTIONS NOTE: Check ALL parts for shipping damage. If shipping damage is noted, DO NOT use. Contact Carrier/Dealer
More informationSTEADYfast Stabilizer Installation Notes Fifth Wheel and Travel Trailers 11/23/13
STEADYfast Stabilizer Installation Notes Fifth Wheel and Travel Trailers 11/23/13 (See Supplemental Instructions for trailers with heavy duty round footplates and/or Power Leveling Systems) PHONE SUPPORT
More informationDIAMOND Retractable Rodding Robot Model SPRAYROD-R
2004-12-21 2 1 (23) DIAMOND Retractable Rodding Robot Model SPRAYROD-R 2004-12-21 2 2 (23) Table of contents 1 TECHNICAL DESCRIPTION...4 1.1 MAIN DETAILS...5 1.2 COMPONENTS DESCRIPTION...5 1.2.1 Pneumatic
More informationSlide the new steering column shaft through the steering column from the driver compartment.
Slide the new steering column shaft through the steering column from the driver compartment. Push the column shaft through the steering column until the machined end is out past the column lower bushing.
More informationSolstice/Sky Water Pump Replacement
Solstice/Sky Water Pump Replacement The water pump on the Solstice/Sky is starting to need replacement on some vehicles. This guide will help in replacing the water pump while the engine is still in the
More informationRoll-Up Door Maintenance Guide
R Roll-Up Door Maintenance Guide Cable Replacement on Two Spring Type Balancer Page 1 Panel Replacement - Removable Roller Cover Type Bottom Panel Page 1 Panel Replacement - Removable Roller Cover Type
More informationINSTALL/REMOVAL INSTRUCTIONS: WINDOW REGULATOR
REMOVAL/INSTALL OF WINDOW REGULATOR (741-306) Honda Accord 2003 07 General Tech Tips: Use painter s tape rather than duct tape to secure window. It will not damage paint or leave sticky residue. A plastic
More informationMicro Cart User's Guide
Micro Cart User's Guide To take full advantage of the ergonomic features of your new Sun Mountain Micro Cart, please read the following information. SUN MOUNTAIN 1 Your Micro Cart has several innovative
More informationMaster Code 2. Troubleshooting: Installation 7. Troubleshooting: Door Jamming and Door Handing 8. Troubleshooting: Keypad 12
Programming and Troubleshooting Guide 1 2 3 4 5 6 Master Code 2 Troubleshooting: Installation 7 Troubleshooting: Door Jamming and Door Handing 8 Troubleshooting: Keypad 12 Troubleshooting: Battery 13 Battery
More informationHYDRAULIC TABLE CART 500-LB.
HYDRAULIC TABLE CART 500-LB. OWNER S MANUAL WARNING: Read carefully and understand all MACHINE ADJUSTMENT AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other basic
More informationFRONT BUMPER INSTALLATION INSTRUCTIONS 2007-2011 DODGE / MERCEDES SPRINTER
Aluminess Products Inc 9402 Wheatlands Ct. #A Santee, CA 92071 619-449-9930 FRONT BUMPER INSTALLATION INSTRUCTIONS 2007-2011 DODGE / MERCEDES SPRINTER Please read before beginning Stainless steel hardware
More informationOperating Instructions Parts List Manual Scissor Lift Pallet Truck
Operating Instructions Parts List Manual Scissor Lift Pallet Truck Note: Operator MUST read and understand this operating instructions before use this Hand Scissor Lift. Thank you for using this hand scissors
More informationWiper Motor Marinco 2.5. Installation Instructions
Wiper Motor Marinco 2.5 Installation Instructions Wiper Motor Marinco-2.5 The Marinco 2.5 Wiper Motor Offers the Following Features: Fully sealed base and housing which allows installation in outdoor wet
More informationSteering column, steering column tube and steering wheel, servicing
48-1 Steering column, steering column tube and steering wheel, servicing Airbag functional check and airbag On Board Diagnostic (OBD) program Repair Manual, Body-Exterior, Body- Interior, Repair Group
More informationINSTRUCTIONS THOROUGHLY BEFORE BEGINNING***************
Bill of Materials: RAC0012 Green Wing Aerodynamic Skirt Kit Item Part Number Description Quantity 1 RMC0218 Gen 2 Trailer Skirt Roadside 1 2 RMC0219 Gen 2 Trailer Skirt Curbside 1 3 RMC0041 Trailer Skirt
More informationRehabilitation. Rehabilitation. Walkers, Crutches, Canes
Walkers, Crutches, Canes These devices provide support through your arms to limit the amount of weight on your operated hip. Initially, after a total hip replacement you will use a walker to get around.
More informationSERVICE MANUAL. Corpus 3G. Seat system for electric wheelchair
SERVICE MANUAL US Corpus 3G Seat system for electric wheelchair How to contact Permobil Head Office of the Permobil group Produced and published by Permobil AB, Sweden Version 4, 2014-07 Item No.: 205260-US-0
More informationLIFT-505. BMF Lift Kit. Yamaha Drive Gas or Electric. Installation Instructions
LIFT-505 BMF Lift Kit Yamaha Drive Gas or Electric Installation Instructions Contents of LIFT-505 Yamaha Drive BMF Lift Kit: a (1 ea.) BMF A-Arm Assembly b (1 ea.) Driver Side Shock Tower c (1 ea.) Passenger
More informationPUMP JACK SYSTEM AND ACCESSORIES
Pump Jack Model # 2200 A low cost, easy to operate, safe, portable scaffolding built of rugged steel. It's perfect for shingling, siding, sheathing, insulating, painting, building, roofing, home repair
More informationPlease read all instructions BEFORE assembly and USE of product. KEEP INSTRUCTIONS FOR FUTURE REFERENCE. Model # 1305TW. Infant car seats not included
Please read all instructions BEFORE assembly and USE of product. KEEP INSTRUCTIONS FOR FUTURE REFERENCE. Model # 1305TW Infant car seats not included Double Snap N Go Instruction Manual Convenience through
More information1000-LB. TRAILER JACK OWNER S MANUAL
1000-LB. TRAILER JACK OWNER S MANUAL WARNING: Read carefully and understand all INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions may result in serious
More informationBanner Stands & Displays
Banner Stands & Displays LEARN MORE ABOUT WHAT WE CAN DO! Looking for a trade show banner stand and display? Showcase your banner anywhere with these high-quality stands and pop-up display systems. If
More informationSERVICE MANUAL Trax US
SERVICE MANUAL Trax US How to contact Permobil Permobil Inc. USA 6961 Eastgate Blvd. Lebanon, TN 37090 USA Phone: 800-736-0925 Fax: 800-231-3256 Email: info@permobilusa.com Head Office of the Permobil
More informationFront axle components, overview
just a test. Front axle components, overview 40-1 General Information Load bearing components and parts of the suspension must not be welded or straightened. Vehicles without drive axle must not be moved,
More informationJohnny G Spinner Pro and Johnny G Spinner Elite Owner s Manual
Johnny G Spinner Pro and Johnny G Spinner Elite Owner s Manual www.startrac.com Table of Contents: 1) Introduction 2) Fitness Safeguards 3) Spinner Pro and Elite Features 4) Assembly Instructions / Parts
More informationVEHICLE EQUIPMENT INSTRUCTIONS
VEHICLE EQUIPMENT INSTRUCTIONS A Table of Contents 1) Ramp and Seats 2) Passenger/Attendant Operation 3) Restraint System City CarShare addenda noted by 1) Ramp and Seats 2 Unfolding Ramp Manual Ramp Operation
More informationDLC:GH B6CJ6A HJEEA:B:CI
SERIES 2 S E RI E S 2 DLC:GH B6CJ6A HJEEA:B:CI SERIAL NUMBER Z2SUPP_0211Rev B - READ THIS MANUAL DO NOT OPERATE THIS WHEELCHAIR WITHOUT FIRST READING AND UNDERSTANDING THIS TiLITE OWNERS MANUAL SUPPLEMENT.
More informationCP2 Buried Cable Pedestal Initial & Rehab Installation Instructions
Printing 3 March 2008 CP2 Buried Cable Pedestal Initial & Rehab Installation Instructions This instruction is intended for CP2 cable pedestal installations and replacements. The following tools will be
More informationRack installation instructions
Rack installation instructions Review the documentation that comes with the rack cabinet for safety and cabling information. Before you install the server in a rack cabinet, review the following guidelines:
More informationMONDOATHENS BASKETBALL SET (Reference PK110)
MONDOATHENS BASKETBALL SET (Reference PK110) DESCRIPTION The MONDOATHENS backstop unit is mainly designed for multi-sports pavilions and installations where the highest-level basketball competitions are
More informationPatient handling techniques to prevent MSDs in health care
28 Introduction Patient handling techniques Work-related musculoskeletal disorders (MSDs) are a serious problem among hospital personnel, and in particular the nursing staff. Of primary concern are back
More informationPEDAL CAR - GO CART ASSEMBLY & OPERATING INSTRUCTIONS
PEDAL CAR - GO CART 42822 ASSEMBLY & OPERATING INSTRUCTIONS 3491 Mission Oaks Blvd., Camarillo, CA 93011 Visit our Web site at: http://www.harborfreight.com Copyright 2000 by Harbor Freight Tools. All
More informationAPPENDIX A. Sets = the completion of one consecutive grouping of repetitions of an exercise.
Exercise Instruction Sheet Instructions: APPENDIX A Exercises are to be performed 3 times per week. Allow one rest day between each exercise day. You may divide the exercises into groups and perform them
More informationHALE PET DOOR INSTALLATION INSTRUCTIONS HALE STANDARD PANEL MODEL
HALE PET DOOR INSTALLATION INSTRUCTIONS HALE STANDARD PANEL MODEL Please read these instructions carefully and completely before attempting to install Hale Pet Doors; they will guide you through the steps
More informationILLUSTRATED PARTS LIST
TW400 WITH 390cc HONDA ENGINE 390cc 2 WHEEL DRIVE UTILITY VEHICLE ILLUSTRATED S LIST 390cc 2WD B O D Y D I A G R A M 390cc 2WD F R A M E D I A G R A M 390cc 2WD D R I V E T R A I N D I A G R A M DESCRIPTION
More informationHP Laser Jet 4200/4240/4250/4300/4350 Swing Plate
HP Laser Jet 4200/4240/4250/4300/4350 Swing Plate 1 Swing Plate Assembly-RM1-0043 1 Swing Plate Kit-5851-2766 (RM1-0043 plus RM1-1091 gear) CAUTION: Fuser may be hot. Turn off printer, unplug it and allow
More informationIMPORTANT INFORMATION - PLEASE READ. Table of Contents. Introduction. General Information
IMPORTANT INFORMATION - PLEASE READ Introduction Congratulations! Welcome to the world of the ELLIPTICAL CROSS TRAINER. The ELLIPTICAL CROSS TRAINER is one of the finest and most comprehensive pieces of
More informationMEASURING WHEEL ALIGNMENT
MEASURING WHEEL ALIGNMENT 2003-04 WHEEL ALIGNMENT Specifications & Procedures - Hummer - H2 Steering and vibration complaints are not always the result of improper alignment. One possible cause is wheel
More informationSPRITE and BIGFOOT DESKTOP CNC MACHINE KIT ASSEMBLY INSTRUCTIONS
SPRITE and BIGFOOT DESKTOP CNC MACHINE KIT ASSEMBLY INSTRUCTIONS README FIRST: Thank you for purchasing your MyDIYCNC Desktop CNC Machine Kit. We hope this versatile and innovative machine brings you many
More informationStreet-Lynx. Reilly MotorSports, Inc. Installation Manual
Street-Lynx By Reilly MotorSports, Inc. Installation Manual 1 1- Begin by removing your original rear suspension disconnect your brake lines, E-brake cables, and remove the driveshaft. To prevent fire
More informationDouble Glider Assembly Instructions.
Double Glider Assembly Instructions. Thank you for purchasing your new Torrans Manufacturing Company s Lawn Glider. Assembly of the Glider can be accomplished by one person however, it is advised that
More informationInstallation instructions, accessories - Handsfree for cellular phone, system B, entry level
XC90 Section Group Weight(Kg/Pounds) Year Month 3 39 0.5/1.1 2006 07 XC90 2003, XC90 2004 IMG-249663 Page 1 of 18 Required tools A0000162 A0000163 IMG-239664 M0000232 IMG-253123 IMG-252223 Page 2 of 18
More informationPower Window/Power Lock Installation. To begin with you will need all the parts listed below:
Power Window/Power Lock Installation To begin with you will need all the parts listed below: From Donor Fiero: Fiero power window regulators Power window motors (Generic GM type part) -motors are riveted
More informationRehabilitation. Rehabilitation. Walking after Total Knee Replacement. Continuous Passive Motion Device
Walking after Total Knee Replacement After your TKR, continue using your walker or crutches until your surgeons tells you it is okay to stop using them. When turning with a walker or crutches DO NOT PIVOT
More informationSPECIFICATIONS FOR BOON EDAM TOMSED MODEL TUT-65TMB
SPECIFICATIONS FOR BOON EDAM TOMSED MODEL TUT-65TMB PRODUCT DESCRIPTION: BOON EDAM TOMSED MODEL TUT-65TMB STAINLESS STEEL BARCODE SCANNING ELECTRONIC REGISTERING TURNSTILE SCOPE OF OPERATION: A. The TUT-65TMB
More informationS&G Model 2937 Group 1 Combination Lock
Installation and Combination Changing Instructions S&G Model 2937 Group 1 Combination Lock NOTE: READ COMPLETE INSTRUCTIONS BEFORE INSTALLATION These instructions should be followed when installing the
More informationCheck for deteriorated, shifting or missing tie-down pads. Replace if needed.
C C 0 5 C H A S S I S F R A M E Chassis Frame Overview The Blue Bird Vision s chassis frame consists of two main C-channel rails which run the entire length of the bus, and several different kinds of cross
More informationThe Grasshopper. Golf Buggy. Owners Manual Junior SE
The Grasshopper Golf Buggy Owners Manual Junior SE TECHNICAL SPECIFICATION Model: JUNIOR SE Power: Single 1000 Watt Electric Motor Transmission: Limited Differential Speed Control: Twist grip step-less
More information5 Mechanisms and accessories
5 Mechanisms and accessories 51A SIDE OPENING ELEMENT MECHANISMS 52A NON-SIDE OPENING ELEMENT MECHANISMS 54A WINDOWS 55A EXTERIOR PROTECTION 56A EXTERIOR EQUIPMENT 57A INTERIOR EQUIPMENT X79 NOVEMBER 2009
More informationHYDRAULIC LIFT TABLE CART 2200-LB.
HYDRAULIC LIFT TABLE CART 2200-LB. OWNER S MANUAL WARNING: Read carefully and understand all MACHINE ADJUSTMENT AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other
More informationHOW TO BUILD A LOU-VEE-AIRCAR
HOW TO BUILD A LOU-VEE-AIRCAR MATERIALS (PER CAR) 1. One sheet of legal-sized paper 2. Three standard paper clips 3. One butterfly paper clip 4. One plastic soda straw 5. Two large index cards 6. Narrow
More informationBase Cabinet with Self-storing Folding Doors and Floor
Usable Kitchens When designing a kitchen for use by persons with mobility impairments, especially those who use wheelchairs, careful layout of the kitchen is crucial to maintaining accessibility. People
More informationFuel Injection Pump, Rotary (005-014)
Fuel Injection Pump, Rotary View Related Topic Page 1 of 30 Fuel Injection Pump, Rotary (005-014) Table of Contents Summary General Information Preparatory Steps Remove Front Gear Train Rear Gear Train
More informationSection A. GENERAL INFORMATION
Section A. GENERAL INFORMATION I. Description The information and instructions for attaching the sidecar to the right-hand side of the motorcycle are contained in this handbook and must be carefully observed.
More informationMaxi-Stamper. 200 to 1,000 Tons STAMPING OUT DOWNTIME
TM Maxi-Stamper 200 to 1,000 Tons STAMPING OUT DOWNTIME Standard Features Steel Fabricated Construction Drive Capacity Rated 1/2 Above Bottom of Stroke Self-Diagnostic Solid State Controller Moveable Operator
More informationSET-UP AND INSTALLATION FOR LEAD SCREW CARTRIDGE ASSEMBLY
SET-UP AND INSTALLATION FOR LEAD SCREW CARTRIDGE ASSEMBLY 82-13-1 O-Ring (Rear) The Lead Screw Assembly is shipped separately. Note: Install Electrical and Pneumatic Circuitry. Be Sure electrical and pneumatic
More informationINSTALLATION AND OPERATING INSTRUCTIONS For Model GL1 Gate Locks
Securitron Magnalock Corp. www.securitron.com ASSA ABLOY, the global leader Tel 800.624.5625 techsupport@securitron.com in door opening solutions INSTALLATION AND OPERATING INSTRUCTIONS For Model GL1 Gate
More information2740 Whitten Rd Bldg 103 Memphis, TN 38133 Telephone 901-380-9290 Email Bwilliams@Dieselcare.net
Fuel Injection Pump Replacement REMOVAL Diesel Care & Performance Inc 1. Disconnect negative battery terminal. 2. Remove throttle linkage. Fuel Injection Pump Bracket 3. Remove injection pump bracket.
More informationWanda Technology Inc. Side Post Aluminum Umbrella OWNER S MANUAL
Wanda Technology Inc. Side Post Aluminum Umbrella Portofino II Series OWNER S MANUAL US Patents: 6,439,249 ; 6,692,135 ; 6,598,990 ; 6,966,667 6,945,263 ; 6,923,194 ; 6,830,058 ; 6,565,060 6,511,033 ;
More informationOregon Fuel Injection
Corporate Office: P.O. Box 21121, VE Pump Removal and Installation Cummins Lock Timed Applications Removal Clean the exterior of the injection pump and mounting surfaces. 1. Disconnect the fuel return
More informationUNPACKING AND ASSEMBLY
UNPACKING AND ASSEMBLY Assembly Instructions Step 1. Open the two boxes and remove all the parts. Lay out the parts as shown below and read through the assembly instructions before beginning assembly.
More informationPallet Jack. OWNER S MANUAL Model MH1230. Important Safety Instructions Assembly Instructions Parts and Hardware Identification
OWNER S MANUAL Model MH1230 Important Safety Instructions Assembly Instructions Parts and Hardware Identification Pallet Jack CAUTION: Read, understand and follow ALL instructions before using this product
More informationASSEMBLY MANUAL SE-4S35
Automatic drive ASSEBLY ANUAL SE-4S35 AI-4S35 SG-4R35 Battery box otor unit Inter-4 hub CONTENTS WARNING 1 INSTALLATION CONITIONS Battery box Speed sensor Cable lengths and diameters otor unit Recommended
More informationSELF-STEERING AXLE TABLE OF CONTENTS
SELF-STEERING AXLE TABLE OF CONTENTS Section 1 - Introduction Section 2 - Pre-Installation Check List Section 3 - Ride Height Adjustments Section 4 - Suspension Mount Section 5 - Axle Mount Section 6 -
More informationThe Drink-Aide The NEW look of independence
The Drink-Aide The NEW look of independence Introducing Drink-Aide What is Drink-Aide? The Drink-Aide is a water bottle that attaches easily to a wheelchair for use by persons with little or no upper
More informationGuide for Modified Assembly: Lightning McQueen. By: Collin Patterson, University of Delaware. Materials and Tools:
Guide for Modified Assembly: Lightning McQueen By: Collin Patterson, University of Delaware Materials and Tools: PVC o 40 inches of 1 in diameter PVC o 25 inches of ¾ in PVC o 4 x 1 in elbows o 2 x ¾ in
More informationI BEAM TRACK INSTALLATION
PDQ 0/700 FESTOON SYSTEM INSTALLATION AND MAINTENANCE INSTRUCTIONS INTRODUCTION The PDQ Festoon System was designed to run on one of three sizes of I-beams: S x., S8 x 8. and S x.. System trolleys must
More information42U/45U 28" Wide Rack Installation & Service Guide
42U/45U 28" Wide Rack Installation & Service Guide 96-00171-005 Rev B Important Information Information in this document is subject to change without notice and does not represent a commitment on the part
More informationLG G5 Chassis Brace Gen 5 Camaro THE MOST POWERFUL HEADERS ON THE PLANET Brought to you by LG Motorsports 972-429-1963
LG G5 Chassis Brace Gen 5 Camaro THE MOST POWERFUL HEADERS ON THE PLANET Brought to you by LG Motorsports 972-429-1963 Thank you for purchasing LG Motorsports products for your Gen 5 Camaro. Parts Inventory:
More informationHOME GYM. Model. Retain This Manual for Reference OWNER'S MANUAL. www.hyper-extension.com
NOTE: Please read all instructions carefully before using this product Table of Contents Safety Notice www.hyper-extension.com HOME GYM 50036 Hardware Identifier Assembly Instruction Parts List Warranty
More informationOriginal Assembly Guide
TCT Multipurpose Single Bevel Sliding Compound Mitre Saw Original Assembly Guide Read instructions before assembling this tool. Table of Contents GB Assembly Guide Read instructions before assembling this
More informationAssembly Instructions for the InteliTrack 3000 Rail Tracking System
Assembly Instructions for the InteliTrack 3000 Rail Tracking System InteliTrack is a trademark of Sedona Solar Technology. Sedona Solar Technology 16 April 2013 1 1. Before you begin WARNING Safety equipment
More informationRange Road RR Series Semi-Automatic Firewood Processor. Crated Unit Assembly Manual
Range Road RR Series Semi-Automatic Firewood Processor Crated Unit Assembly Manual 1 1) Undo 8-18mm x 19mm Nuts and bolts, 2 on each leg of top frame 2) Lift top of Metal crate off and move out of work
More informationOperating Instructions
587W Clinical Care Recliner Operating Instructions 587W-INS-LAB Graham-Field Health Products 2005 IMPORTANT: READ THIS MANUAL BEFORE OPERATING YOUR ORTHO-BIOTIC CLINICAL CARE RECLINER WARNINGS Warning:
More informationGIBRALTAR 6000 Series Cymbal Stands
GIBRALTAR 6000 Series Cymbal Stands Gibraltar Upgrades 6000 Series Cymbal Stands with Swing Nut fast cymbal mounting system. Professional in features yet light enough in weight and mass for easy transport.
More informationINSTRUCTION. Industrial Sewing Machines. No. 010012. First published : June 1997 Second edition : March 2001
INSTRUCTION Industrial Sewing Machines First published : June 1997 Second edition : March 2001 No. 010012 INTRODUCTION Thank you for your purchasing Kansai Special's DLR Series. Read and study this instruction
More informationSTEERING HANDLEBAR/FRONT WHEEL/ FRONT SHOCK ABSORBER
14 14 STEERING HANDLEBAR/FRONT WHEEL/ SCHEMATIC DRAWING ------------------------------------------------- 14-1 SERVICE INFORMATION------------------------------------------------ 14-2 TROUBLESHOOTING-----------------------------------------------------
More informationAll-Season Sunroom Sliding Glass Door Installation Instructions
ASRESGD-08 All-Season Sunroom Sliding Glass Door Installation Instructions Panel Frame Door Frame Left Side Foam Insulator IE241 H Bar Assembly Door Frame Top Track Panel Frame Door Frame Right Side Stationary
More informationPOWERS Controls No. 4 Pneumatic Damper Actuator
POWERS Controls No. 4 Pneumatic Damper Actuator Technical Instructions Document No. 155-032P25 AP 331-2 Actuator Assembly 331-2929 Typical Actuator Assembly 331-2904 Typical Actuator Assembly 331-3000
More informationOperating Instructions
566DG Ortho-Biotic Clinical Care Drop Arm Recliner Operating Instructions 566DG-INS-LAB Graham-Field Health Products 2005 IMPORTANT: READ THIS MANUAL BEFORE OPERATING YOUR ORTHO-BIOTIC CLINICAL CARE DROP
More informationLU6X-130 Instructions and Parts List (including LU6X Basic) Operating Instructions
LORTONE LU6X-130 Item # 061-092 LU6X Basic Item # 061-090 LU6X-130 Instructions and Parts List (including LU6X Basic) Operating Instructions Introduction The LU6X is one the most versatile pieces of equipment
More informationSebring Timing Belt and Water Pump Replacement
Sebring Timing Belt and Water Pump Replacement I was motivated to do this work because of a bearing growling sound emanating from the engine. It would grind at low rpms when the engine was cold and then
More informationBicycoo BMX Instruction Manual 0014X Series
Bicycoo BMX Instruction Manual 0014X Series Joovy 2919 Canton Street Dallas, TX 75226 (877) 456-5049 Fax: (214) 761-1774 Email: customerservice@joovy.com Web Site: www.joovy.com ! WARNINGS Please read
More informationPole Lathe and Shave Horse Design
Pole Lathe and Shave Horse Design These pictures and accompanying words are Copyright Michael Hughes February 2002. They are not to be re-produced, in part or whole, without permission from the author.
More informationOperating Instructions
574G Ortho-Biotic 3-Position Recliner Operating Instructions 574G-INS-LAB Graham-Field Health Products 2005 IMPORTANT: READ THIS MANUAL BEFORE OPERATING YOUR ORTHO-BIOTIC 3-POSITION RECLINER WARNINGS Warning:
More informationP7100 PUMP INSTALLATION INSTRUCTIONS Diesel Care & Performance Inc
P7100 PUMP INSTALLATION INSTRUCTIONS Diesel Care & Performance Inc Installation Timing Pin Location CAUTION: Before installing the injection pump, be sure that number 1 cylinder is at the Top Dead Center
More informationSERVICE PARTS LIST PAGE 1 OF 6 BASE ASSEMBLY SPECIFY CATALOG NO. AND SERIAL NO. WHEN ORDERING PARTS 12" DUAL BEVEL COMPOUND MITER SAW B27A
PAGE 1 OF 6 BASE ASSEMBLY 00 0 EXAMPLE: Component Parts (Small #) Are Included When Ordering The Assembly (Large #). SPECIFY CATALOG NO. AND NO. WHEN ORDERING PARTS 1 02-80-0050 Thrust Bearing (1) 2 05-80-0510
More information