New Features in CUCM 9.0
|
|
- Sibyl Burke
- 2 years ago
- Views:
Transcription
1 New Features in CUCM 9.0 Compiled by and Additional notes by John Meersma Unified Communications Specialized Instructor Pause in Speed Dial Users can configure speed dials with FAC, CMC and post connect DTMF Comma accepted in speed dial as delimiter and pause Feature allows two methods of configuration: Method 1: Using comma as a pause and also as a delimiter Method 2: Dialstring/FAC/CMC/Post connect digits with no commas Method 1: Command Delimiter for Pause Comma used to delineate dial string, FAC, CMC, and post connect digits For post connect digits, commas insert a 2 second delay Commas may be duplicated to create longer delays Preferred method for non-cupc devices Method 2: No Comma All digits to be used for dial string, FAC, CMC and post call digits entered as one string Once a digit string has been matched, CUCM moves on to next digit string Can be used on SCCP and SIP phones, but required for CUPC Pause in Speed Dial Examples ,,,, Will dial , after connect, wait 8 seconds to dial #,2244 FAC for International Calls. Will dial # with FAC of ,6534,5656,,,9933 Will dial , with a FAC of 6534 and CMC of 5656, wait 6 seconds, the dial the DTMF digits Will dial with a FAC of 6534 and CMC of 5656, then immediately after connect, dial 9933 New Service Parameter allows configuration of interdigit delay If the speed dial FAC or CMC is wrong Method 1: Call disconnects and an error is displayed Method 2: phone displays an error and allows user to manually enter information Pause in Speed Dial Caveats Dial string is truncated in the calls history list (only dialed number) Feature may not work with CUPC client and variable length/overlapping dialplans (no comma delineation) This feature is not supported SRST
2 Codec Preference Pre CUCM 9.0 Administrator could only eliminate codecs (based on Maximum Audio Bit Rate) Could not prioritize G.711alaw over G.711ulaw, or G.729 codecs With CUCM 9.0 System default codec preference same as earlier versions Allow administrator to deterministically specify codec order Allow codec selection based on received offer Custom Codec list applied globally or on a GW/Trunk Level Can be applied to: SIP, MGCP, SCCP, H323 and EMCC Codecs preference still choose by Regions For SIP Devices/Trunk, can specify Accept Codec Preference in received Offer Can change codec selection for EMCC logged in devices Codec Preference Caveats A common Codec Preference List must be the same on all clusters when using the following features: Extension Mobility Cross Cluster H323 Inter Cluster Trunks Biggest challenge will be unexpected codec Check Accept Audio Codec Preferences in Received Offer settings Check at Device level and system level When using non-pass through MTP, codec negotiated hop-by-hop Native Call Queuing Enables Hunt Pilot to queue callers Allow for redirection of calls based on different queue criteria Allow agents to participate in multiple queues Auto logout and call re-queue if agent does not answer Longest waiting call in all queues will be delivered first No post call time or agent greeting options On phone Queue Status display
3 Cisco Extend and Connect What is the existing limitation? Using CTI (webex connect or CUCILync), user can monitor a calls, but not control the call No enterprise features for non-cucm registered devices Cannot hold/resume, transfer, conference or park Remote devices ring and can be answered, but not mid-call features What is Cisco Extend and Connect? A new device type, CTI Remote Device that represents all remote destinations for a user Anchors enterprise calls on the CTI Remote Device Allows a CTI application (like Jabber) 3rd party control of the remote connection to enable enterprise call features Examples of a deployment scenario Contact Center agent working from home Low bandwidth at house, VOIP not an option (hard phone or soft client) and cell phone is not an option Extend connect sends call to home phone and CAD agent allows enterprise features needed for contact center agents Use Cisco Unified Communications with legacy PBX Customer has PBX under contract and not ready to move phones Customer wants UC for IM, Chat and messaging, but phones on PBX Extend Connect enables Jabber deployment for UC, but enterprise control of PBX phone (as remote device for Jabber) New End User Webpages CUCM 9.0 now has two types of end-user s webpages One type of page is for core Users with one phone and one line The other page will be for users with multiple phones with one or more lines on each device New User Page UI targeted towards core users Cisco Mobility Updates Simultaneous Ring in previous versions of CUCM CUCM 7.0 introduced the parameter Reroute Remote Destination Calls to Enterprise Number Calls direct to cell would ignore time of day settings and call the cell Calls would be anchor on the enterprise phone.but the line would not ring New features in CUCM 9.0: Added Ring All Shared Lines service parameter Uses Boolean Setting True all lines (including other remote destinations) ring False only the dialed number (remote destination) rings Default and existing behavior is False
4 Single Number Reach Voic The Problem: When a call is extended to a SNR destination, CUCM cannot determine if the call was answered by the user or VM Based on Answer Too Soon Time based mechanism is unreliable and requires tweaking for each service provider New Solution CUCM 9.0 introduces a new parameter called Single Number Reach Voic Policy Can be either Timer Controlled or User Controlled Timer Controlled uses existing Answer Too Soon timer User Controlled requires the user to send a signal (DTMF) to accept the call Hunt Pilot Connected Number Display Hunt pilot DN display in previous versions Calls to a hunt pilot display the DN of the hunt pilot as the connected party ID Applies to both MGCP and SIP trunks Hunt pilot DN display in CUCM 9.0 This feature allows the connection to be updated with the answering party s DN as the Called Party ID Applied on the Hunt Pilot Configuration page SIP: PAI and Remote PartyID are updated MGCP/H323: Connected Number sent to update the Called Party ID RTCP Support RTCP RTCP provides out-of-band statistics and control info for RTP RTP sent on even port and RTCP is send over next higher odd port RTCP is supported between phones directly RTCP not supported by: Trusted Relay Point (TRP) RSVP Agent DTMF Translator Passthru MTP CUCM 9.0 RTCP New features: CUCM 9.0 supports RTCP through MTP in pass thru mode In non-pass thru mode, RTCP will still be blocked Only valid for SIP to SIP calls
5 BRI G.Clear CUCM v7.0 (1) first introduced G.Clear support for MGCP PRI G.Clear required for tandem ISDN bearer circuits in VOIP network New features: CUCM 9.0 expands support for G.Clear to BRI interfaces Supported on MGCP BRI interface Supports G.Clear over SIP trunk with Early Offer and G.Clear Security and OS Updates Red Hat Enterprise Linux 5.0 v7.0.2 Host rename/reip simplified (3 less steps to complete) Optimized CLI commands: Utils dbreplication stop/dropadmindb/reset Utils dbreplication forcedatasyncsub Utils dbreplication status replicate Utils dbreplication runtimestate Upgrade paths L2 upgrade from 8.6(1) and later to 9.0(1) Refresh Upgrade for 8.x (prior to 8.5), 7.1(5) and 6.1(5) Security Feature Update CTL Client Update Single installer for all Windows versions Supports Windows 7 (32 and 64 bit), Windows XP and Windows Vista Updates to AXIS 2.0 (support.net clients) Assured Services for SIP Line side devices MLPP support for 99xx/89xx SIP phones and 3rd party SIP Phone TLS connections for 3rd party SIP phones LDAP Enhancements Custom User Fields Existing LDAP agreements sync 13 default attributes LDAP agreements will allow 5 Custom User fields Custom User Fields are common across all sync agreements Custom User Fields updated on 1 agreement are synched across all agreements Attribute will be validated at save time Error message thrown when saving and the attribute does not exist
6 LDAP and Manual User Support Prior to CUCM 9.0 Enabling LDAP sync would prohibit adding local users End user to be used by CUCM must be defined on AD and synched Extra users could trigger extra CAL s on the MS AD With CUCM 9.0 Administrator can have both LDAP sync users and locally defined users Ability to modify local users and roles assigned to LDAP users Deleting LDAP synch will mark users synced for deletion (garbage collection) Administrator can convert an LDAP user to a local user User status field is used to differentiate between the Local user and LDAP Synchronized users To convert LDAP synchronized user to the local user account: Check the box Convert User Account and Save changes After a user is converted to local CUCM user all the fields become editable CUCM IM and Presence Beginning with release 9.0, CUCM and CUP will start integration to be one product Includes common release and upgrade process Centralize administration Simplify licensing, now included as part of CUCM user licensing Deprecating IP Phone Messenger (IPPM) and CUPC 7.0 Through CUCM IM and Presence administration screens, configure UC Services for clients UC Services that can be defined: Voice Mail Visual Voice Mail Conferencing Directory IM Presence CTI UC Services are used to build a UC Service Profile UC Service Profiles assigned to users: Licensing for the feature handled at the user level Home cluster specified in the user page When migrating to CUCM 9.0, existing service profiles and configuration in CUP will be migrated CUCM IM and Presence uses Templates and Layouts to speed up user creation BAT/AXL have been updated for CUCM/CUCM IM and Presence
CISCO UNIFIED COMMUNICATIONS MANAGER
CISCO UNIFIED COMMUNICATIONS MANAGER V10 UPDATED TOPICS LOCAL ROUTE GROUP ENHANCEMENT Multiple Local Route Groups can be associated with Route Groups for Emergency Dialing. In releases 8 and 9, administrators
Introducing Cisco Voice and Unified Communications Administration Volume 1
Introducing Cisco Voice and Unified Communications Administration Volume 1 Course Introduction Overview Learner Skills and Knowledge Course Goal and Course Flow Additional Cisco Glossary of Terms Your
New aspects of Cisco UC Interoperability. #CiscoPlus
New aspects of Cisco UC Interoperability #CiscoPlus What is integration? Is my home phone integrated with your home phone? Is my corporate email system federated with yours? Does integration imply connecting
Implementing Cisco Unified Communications Manager Part 1, Volume 1
Implementing Cisco Unified Communications Manager Part 1, Volume 1 Course Introduction Overview Learner Skills and Knowledge Course Goal and Course Flow Additional Cisco Glossary of Terms Your Training
Configure Call Queuing
Call Queuing Overview, page 1 Call Queuing Prerequisites, page 2 Call Queuing Task Flow, page 3 Call Queuing Interactions and Restrictions, page 9 Call Queuing Overview Cisco Unified Communications Manager
Troubleshooting SIP Trunks with Cisco CallManager 5.x and Later
Troubleshooting SIP Trunks with Cisco CallManager 5.x and Later Document ID: 98524 Contents Introduction Prerequisites Requirements Components Used Conventions SIP with CallManager 5.x Media Termination
IP PBX. SD Card Slot. FXO Ports. PBX WAN port. FXO Ports LED, RED means online
1 IP PBX SD Card Slot FXO Ports PBX LAN port PBX WAN port FXO Ports LED, RED means online 2 Connect the IP PBX to Your LAN Internet PSTN Router Ethernet Switch FXO Ports 3 Access the PBX s WEB GUI The
640-461: Introducing Cisco Voice and Unified Communications Administration (ICOMM) v8.0 Course Introduction
640-461: Introducing Cisco Voice and Unified Communications Administration (ICOMM) v8.0 Course Introduction Course Introduction Module 01 - Overview of Cisco Unified Communications Solutions Understanding
Configuration Checklist for Immediate Divert
CHAPTER 27 The (idivert) feature allows you to immediately divert a call to a voice-messaging system. When the call gets diverted, the line becomes available to make or receive new calls. This chapter
Jabber for Android Configuration Example
Jabber for Android Configuration Example Document ID: 113471 Contents Introduction Prerequisites Requirements Components Used Conventions Main Task High level Steps Download the Device COP file Install
Cisco Networks (ONT) 2006 Cisco Systems, Inc. All rights reserved.
Optimizing Converged Cisco Networks (ONT) reserved. Lesson 2.4: Calculating Bandwidth Requirements for VoIP reserved. Objectives Describe factors influencing encapsulation overhead and bandwidth requirements
Configuration Note for Jeron Provider 790 and Cisco CallManager
Configuration Note for Jeron Provider 790 and Cisco CallManager 1. Jeron Provider 790 Setup 1.1 Configure the SIP Server Connectivity Set Brekeke SIP Server's IP address in the [SIP Server IP] field and
Implementing Intercluster Lookup Service
Appendix 11 Implementing Intercluster Lookup Service Overview When using the Session Initiation Protocol (SIP), it is possible to use the Uniform Resource Identifier (URI) format for addressing an end
Base on-premises deployment You start your on-premises deployment with the base functionality of instant messaging and presence.
Deployment Models Cisco Jabber for Windows provides two deployment models, on-premises or cloud-based. Learn about each deployment model and review the available options for on-premises and cloud-based
Cisco CCA Tool SIP Security methods
Cisco CCA Tool SIP Security methods The Cisco CCA tool (Cisco Configuration Assistant) provides a graphical interface for configuring the UC500 series devices. Once settings have been established using
CISCO UNIFIED COMMUNICATIONS MANAGER SIP INTEGRATION
CISCO UNIFIED COMMUNICATIONS MANAGER SIP INTEGRATION Validated Integrations: 8.5 with xic version 3.0 SU-10 and greater INTEGRATION DOCUMENT Version 2.03 7601 Interactive Way Indianapolis, IN 46278 Telephone/Fax:
Configuring the Dolby Conference Phone with Cisco Unified Communications Manager
Configuring the Dolby Conference Phone with Cisco Unified Communications Manager Version 1.2 December 10, 2015 This product is protected by one or more patents in the United States and elsewhere. For more
Administering Cisco Unified Communications Manager (ACUCM) v10.0
Administering Cisco Unified Communications Manager (ACUCM) v10.0 This five day instructor-led course presented by Cisco training partners to their end customers. Students will learn the basic procedures
IP Office 7.0 and BCM 6.0 SIP Interoperability Configuration Notes
IP Office 7.0 and BCM 6.0 SIP Interoperability Configuration Notes Abstract: This document provides information on how to configure a network solution with IP Office 7.0 and BCM 6.0 using SIP trunks. 2011
Optimizing Converged Cisco Networks (ONT)
Optimizing Converged Cisco Networks (ONT) Module 2: Cisco VoIP Implementations (Deploy) Calculating Bandwidth Requirements for VoIP Objectives Describe factors influencing encapsulation overhead and bandwidth
Software-Powered VoIP
Software-Powered VoIP Ali Rohani Anthony Murphy Scott Stubberfield Unified Communications Architecture Core Scenarios UC endpoints QOE Monitoring Archiving CDR AOL Public IM Clouds Yahoo Remote Users MSN
Arc Connect for Cisco CallManager - System Design Guide
Arc Connect for Cisco CallManager - System Design Guide Arc Solutions, 5 Bourne Court, Southend Road, Woodford, Essex, IG8 8HD United Kingdom Tel: +44 (0)208 498 8400, Fax: +44 (0)208 498 8499 www.arcsolutions.com
ADTRAN SBC and Cisco Unified Call Manager SIP Trunk Interoperability
6AOSSG0004-42A April 2013 Interoperability Guide ADTRAN SBC and Cisco Unified Call Manager SIP Trunk Interoperability This guide describes an example configuration used in testing the interoperability
IMPLEMENTING CISCO VOICE COMMUNICATIONS AND QOS Volume 1
IMPLEMENTING CISCO VOICE COMMUNICATIONS AND QOS Volume 1 Course Introduction Overview Learner Skills and Knowledge Course Goal and Course Flow Additional References Cisco Glossary of Terms Your Training
Hotline. Configure Hotline
This chapter provides information about the hotline feature which extends the Private Line Automatic Ringdown (PLAR) feature, which allows you to configure a phone so that when the user goes off hook (or
SIP Trunking using Optimum Business SIP Trunk Adaptor and the Cisco Call Manager Express Version 8.5
CISCO SIP Trunking using Optimum Business SIP Trunk Adaptor and the Cisco Call Manager Express Version 8.5 Goal The purpose of this configuration guide is to describe the steps needed to configure the
Polycom Unified Communications Deployment Guide for Cisco Environments
Polycom Unified Communications Deployment Guide for Cisco Environments Wave 5 March 2012 3725-00010-001G Trademark Information Polycom, the Polycom Triangles logo, and the names and marks associated with
Benefits Of Upgrading To The Latest CIX Processor
Benefits Of Upgrading To The Latest CIX Processor The Bits: This document is a reference to help you discover the benefits of selling existing Strata CIX system upgrading to release 4 processor: ACTU3A,
Design Considerations
CHAPTER 4 QoS Recommendations Financial Institutions have many business applications that have different requirements for priority when traffic congestion occurs. A strategic QoS deployment will allow
SIP Trunking, ITSP Checklist
SIP Trunking, ITSP Checklist Note: This is not an official document of any kind so please do your own homework and research and also note that Vocale Ltd (owner of the SIP School) does not accept any responsibility
ACCELERATOR 6.3 ASTERISK 1.4 INTEGRATION GUIDE
ACCELERATOR 6.3 ASTERISK 1.4 INTEGRATION GUIDE October 2014 Tango Networks, Inc. phone: +1 469-229-6000 3801 Parkwood Blvd, Suite 500 fax: +1 469-467-9840 Frisco, Texas 75034 USA www.tango-networks.com
ACCELERATOR 6.3 SIP TRUNK PBX INTEGRATION GUIDE
ACCELERATOR 6.3 SIP TRUNK PBX INTEGRATION GUIDE April 2014 Tango Networks, Inc. phone: +1 469-229-6000 3801 Parkwood Blvd, Suite 500 fax: +1 469-467-9840 Frisco, Texas 75034 USA www.tango-networks.com
Application Note: Cisco Integration with Onsight Connect
Application Note: Cisco Integration with Onsight Connect Table of Contents Application Note:... 1 Cisco Integration with Onsight Connect... 3 Direct Onsight Device to Cisco Endpoint Calls... 3 Cisco Unified
Registering with Cisco UC500/CME Series
FLX VoIP Registering with Cisco UC500/CME Series Date: March 13 th, 2012 This technical note gives a detailed description on how to register a Revolabs FLX conference phone with a Cisco UC 500/CME series.
Migrating WebEx Connect Users to Cisco Jabber
Planning Guide Migrating WebEx Connect Users to Cisco Jabber Information for System Administrators Introduction The Cisco WebEx Messenger service provides an instant messaging / chat based collaboration
Conference Bridge setup
Conference Bridge setup This chapter provides information to configure conference bridges using Cisco Unified Communications Manager Administration. See the following for additional information: Conference
Alcatel-Lucent OmniPCX R11.1 using SIP trunk to Cisco Unified Communications Manager Release SU3
Application No Application Note Alcatel-Lucent OmniPCX R11.1 using SIP trunk to Cisco Unified Communications Manager Release 10.5.2 SU3 Page 1 of 107 Table of Contents Introduction... 4 The following items
Version dated 25/11/2014. 1.Course Title. NATO Voice over IP Foundation Course. 2.Identification Number (ID) 3. Purpose of the Course
1.Course Title Version dated 25/11/2014 NATO Voice over IP Foundation Course 2.Identification Number (ID) 095 3. Purpose of the Course There are a number of new technologies (to NATO) that are encompassed
Curso de Telefonía IP para el MTC. Sesión 1 Introducción. Mg. Antonio Ocampo Zúñiga
Curso de Telefonía IP para el MTC Sesión 1 Introducción Mg. Antonio Ocampo Zúñiga Conceptos Generales VoIP Essentials Family of technologies Carries voice calls over an IP network VoIP services convert
IP- PBX. Functionality Options
IP- PBX Functionality Options With the powerful features integrated in the AtomOS system from AtomAmpd, installing & configuring a cost- effective and extensible VoIP solution is easily possible. 4/26/10
Avaya IP Office 8.1 Configuration Guide
Avaya IP Office 8.1 Configuration Guide Performed By tekvizion PVS, Inc. Contact: 214-242-5900 www.tekvizion.com Revision: 1.1 Date: 10/14/2013 Copyright 2013 by tekvizion PVS, Inc. All Rights Reserved.
LessWires Advanced IP Soft-PBX System
LessWires Advanced IP Soft-PBX System Our IP soft-pbx is a complete communications platform. In addition to having PBX functionality, the system is a soft-switch, a protocol gateway, a media server, and
Product Datasheet Global Directory & Options
Product Datasheet Global & Options applications for Cisco Unified Communications Solutions IPS Global Web IPS Popup Personal ClickNDial Provisioning Corporate Speed Dials IP Phone Applications IPS Manager
Configuring the Cisco Unified IP Phone for MIDlets
CHAPTER 2 Configuring the Cisco Unified IP Phone for MIDlets Revised: January 2012, Contents This chapter describes how to configure and manage the Cisco Unified IP Phone and the Enhanced Phone User Interface
Product Datasheet FrontDesk Attendant Console
Product Datasheet FrontDesk Attendant Console applications for Cisco Unified Communications Directory Solutions IPS Global Directory Web Directory IPS Popup Personal Directory ClickNDial Provisioning Corporate
Genesys SIP Transforming Customer Service. Richard Barton Bill Mitchell Jim Kraeutler
Genesys SIP Transforming Customer Service Richard Barton Bill Mitchell Jim Kraeutler Genesys SIP as Single Platform Virtualize Operation Multi-site, Remote/Home Agent, Cloud Operation Flexibility Simplify
Application Notes for Configuring SIP Trunking between Metaswitch MetaSphere CFS and Avaya IP Office Issue 1.0
Avaya Solution & Interoperability Test Lab Application Notes for Configuring SIP Trunking between Metaswitch MetaSphere CFS and Avaya IP Office Issue 1.0 Abstract These Application Notes describe the steps
Voice over IP Basics for IT Technicians
Voice over IP Basics for IT Technicians White Paper Executive summary The IP phone is coming or has arrived on desk near you. The IP phone is not a PC, but does have a number of hardware and software elements
Universal Unified Communications Integration
Universal Unified Communications Integration Managing the convergence of unified communications to IP and into the cloud The Computer & Instrumentation Chapter of the IEEE New Jersey Coast Section October
ACCELERATOR 6.3 AASTRA MX-ONE INTEGRATION GUIDE
ACCELERATOR 6.3 AASTRA MX-ONE INTEGRATION GUIDE September 2014 Tango Networks, Inc. phone: +1 469-229-6000 3801 Parkwood Blvd, Suite 500 fax: +1 469-467-9840 Frisco, Texas 75034 USA www.tango-networks.com
innovaphone Delta list V10
Version 10 includes both new products and new functionalities as well as small updates for earlier versions. This document aims to provide information to technical readers who are familiar with the innovaphone
Understanding Session Initiation Protocol (SIP)
CHAPTER 42 This chapter describes SIP and the interaction between SIP and Cisco Unified Communications Manager. This section covers the following topics: SIP Trunk Configuration Checklist, page 42-1 SIP
Using Avaya Flare Experience for Windows
Using Avaya Flare Experience for Windows Release 9.0 Issue 02.01 September 2013 Contents Chapter 1: About Flare Experience... 5 About Flare Experience... 5 Main window... 6 Button descriptions... 10 Chapter
ACCELERATOR 6.3 ASTERISK LINES INTEGRATION GUIDE
ACCELERATOR 6.3 ASTERISK LINES INTEGRATION GUIDE January 2014 Tango Networks, Inc. phone: +1 469-229-6000 3801 Parkwood Blvd, Suite 500 fax: +1 469-467-9840 Frisco, Texas 75034 USA www.tango-networks.com
Wildix W04FXO Whitepaper
Wildix W04FXO Whitepaper Thanks to Wildix W04FXO gateway, you can enchance your legacy PBX with Unified Communications capabilities. You can connect up to 4 lines to the W04FXO, each of them can be set
Technical Configuration Notes
MITEL SIPCoE Technical Configuration Notes Configure Inn-Phone SIP Phone for use with MCD SIP CoE NOTICE The information contained in this document is believed to be accurate in all respects but is not
Implementing Cisco Collaboration Devices CICD v1.0; 5 Days; Instructor-led
Implementing Cisco Collaboration Devices CICD v1.0; 5 Days; Instructor-led Course Description Implementing Cisco Collaboration Devices (CICD v1.0) is an extended hours 5-day course focusing on providing
Communications Manager Administration **Developed by Skyline ATS** Communications Manager Administration**Developed by Skyline ATS**
Course: Communications Manager Administration Duration: 3 Day Hands-On Lab & Lecture Course Price: $ 2,695.00 Learning Credits: 27 Description: Communications Manager Administration for Version 9.0 (CMA90)
Cisco Mobile VoiP clients
This chapter provides information about functionality for Cisco Mobile VoiP Clients which connect directly with Cisco Unified Communications Manager. This chapter discusses the features and the required
ACCELERATOR 6.3 TDM PBX INTEGRATION GUIDE
ACCELERATOR 6.3 TDM PBX INTEGRATION GUIDE April 2014 Tango Networks, Inc. phone: +1 469-229-6000 3801 Parkwood Blvd, Suite 500 fax: +1 469-467-9840 Frisco, Texas 75034 USA www.tango-networks.com 2004-2014
Configuring the Sonus SBC 2000 with Cisco Unified Call Manager 10.5 for Verizon Deployment
Configuring the Sonus SBC 2000 with Cisco Unified Call Manager 10.5 for Verizon Deployment Application Notes Rev 1.0 P/N 550-06690 Last Updated: October 26, 2015 Revision History Revision Date Revised
Cisco Unified Communications Manager with Cisco Expressway (SIP Trunk)
Cisco Unified Communications Manager with Cisco Expressway (SIP Trunk) Deployment Guide Cisco Expressway X8.2 Unified CM 8.6.x, 9.x January 2015 Contents Introduction 4 Deployment scenario 4 Configuring
Voice over IP (VoIP) Basics for IT Technicians
Voice over IP (VoIP) Basics for IT Technicians VoIP brings a new environment to the network technician that requires expanded knowledge and tools to deploy and troubleshoot IP phones. This paper provides
640-460. IIUC Implementing Cisco IOS Unified Communications (IIUC) Version: Demo. Page <<1/9>>
640-460 IIUC Implementing Cisco IOS Unified Communications (IIUC) Version: Demo Page 1. You are CCNA VOICE associate in XXXX.com. You need configure a voice port that will allow the gateway to
Application Notes for Configuring Broadvox SIP Trunking with Avaya IP Office - Issue 1.0
Avaya Solution & Interoperability Test Lab Application Notes for Configuring Broadvox SIP Trunking with Avaya IP Office - Issue 1.0 Abstract These Application Notes describe the procedures for configuring
Deploying Cisco Unified Contact Center Express Volume 1
Deploying Cisco Unified Contact Center Express Volume 1 Course Introduction Learner Skills and Knowledge Course Goal and Course Flow Additional References Your Training Curriculum General Administration
Cisco Unified Communications Manager (CUCM) 8.x
Cisco Unified Communications Manager (CUCM) 8.x Chesapeake NetCraftsmen David Hailey Cisco Mid-Atlantic User s Group May 2011 1 Agenda Software Releases Enhancements to CUCM 8.x Upgrade Paths Key Takeaways
Configuring Interoperability between Avaya IP Office and Avaya Communication Manager
Configuring Interoperability between Avaya IP Office and Avaya Communication Issue 01.01 Contents 1.0 Introduction... 3 1.1 Supported Features... 3 1.2 Network Diagram... 6 1.3 Supported Phones... 6 1.4
Application Notes for Configuring Microsoft Office Communications Server 2007 R2 and Avaya IP Office PSTN Call Routing - Issue 1.0
Avaya Solution & Interoperability Test Lab Application Notes for Configuring Microsoft Office Communications Server 2007 R2 and Avaya IP Office PSTN Call Routing - Issue 1.0 Abstract These Application
The Competella Attendant and Agent clients are Windows-based. Management- and configuration tools are web-based.
Unified Communication Suite for Microsoft Lync - Product Guide Release 2013 R1 May 31, 2013 Overview The Competella Unified Communication Suite includes excellent tools for switchboard attendants and contact
Application Note - IP Trunking
Application Note - IP Trunking End-to-End Configuration for IP Trunking This document gives you a detailed description of how to configure IP Trunking in a Tenor VoIP system. The following topics are included
Whitepaper: Microsoft Office Communications Server 2007 R2 and Cisco Unified Communications Manager Integration Options
Whitepaper: Microsoft Office Communications Server 2007 R2 and Cisco Unified Communications Manager Integration Options Document Summary This document provides information on several integration scenarios
Application Notes for Configuring Cablevision Optimum Voice SIP Trunking with Avaya IP Office - Issue 1.1
Avaya Solution & Interoperability Test Lab Application Notes for Configuring Cablevision Optimum Voice SIP Trunking with Avaya IP Office - Issue 1.1 Abstract These Application Notes describe the procedures
D. No calling search space has been configured on the line. E. An incorrect device pool has been configured on the phone
1. An end user reports that they are unable to control their Cisco IP phone using Cisco Unified Personal Communicator and cannot make any calls. Which situation can cause this issue? A. The Cisco Unified
Expert Reference Series of White Papers. Troubleshooting Signaling with Traces in Cisco Unified Communications Manager
Expert Reference Series of White Papers Troubleshooting Signaling with Traces in Cisco Unified Communications Manager 1-800-COURSES www.globalknowledge.com Troubleshooting Signaling with Traces in Cisco
Mediatrix 3000 with Asterisk June 22, 2011
Mediatrix 3000 with Asterisk June 22, 2011 Proprietary 2011 Media5 Corporation Table of Contents Introduction... 3 Network Topology... 3 Equipment Detail... 3 Configuration of the Fax Extension... 4 Configuration
ShoreTel & AMTELCO Infinity Console via SIP Trunking (Native)
Product: ShoreTel AMTELCO Infinity Console I n n o v a t i o n N e t w o r k A p p N o t e IN-15063 Date : October, 2015 System version: ShoreTel 14.2 ShoreTel & AMTELCO Infinity Console via SIP Trunking
Application Notes for Configuring Intelepeer SIP Trunking with Avaya IP Office 7.0 - Issue 1.0
Avaya Solution & Interoperability Test Lab Application Notes for Configuring Intelepeer SIP Trunking with Avaya IP Office 7.0 - Issue 1.0 Abstract These Application Notes describe the procedures for configuring
VoIP Bandwidth Considerations - design decisions
VoIP Bandwidth Considerations - design decisions When calculating the bandwidth requirements for a VoIP implementation the two main protocols are: a signalling protocol such as SIP, H.323, SCCP, IAX or
Cisco Mobile VoiP Clients
CHAPTER 16 Cisco Unified Communications Manager provides certain functionality for that connect directly with Cisco Unified Communications Manager. This chapter discusses the features and the required
Cisco Unified Video Conferencing Configuration
Cisco Unified Video Conferencing Configuration This topic provides a reference configuration for Cisco Unified Video Conferencing within a Cisco Unified Communications deployment. The information is based
Frequently Asked Questions: Cisco Jabber 9.x for Android
Frequently Asked Questions Frequently Asked Questions: Cisco Jabber 9.x for Android Frequently Asked Questions (FAQs) 2 Setup 2 Basics 4 Connectivity 8 Calls 9 Contacts and Directory Search 14 Voicemail
SIP Trunk Recording Configuration For CUCM 6.x Version 8.0
SIP Trunk Recording Configuration For CUCM 6.x Version 8.0 REVCORD Voice Logging Systems 10575 Katy Freeway, Suite 470, Houston, Texas 77024 Phone 281-404-7040 Fax 281-404-5323 Toll Free: 1-866-559-2188
FortiVoice. Version 7.00 User Guide
FortiVoice Version 7.00 User Guide FortiVoice Version 7.00 User Guide Revision 2 28 October 2011 Copyright 2011 Fortinet, Inc. All rights reserved. Contents and terms are subject to change by Fortinet
Application Notes for BT Wholesale/HIPCOM SIP Trunk Service and Avaya IP Office 8.0 Issue 1.0
Avaya Solution & Interoperability Test Lab Application Notes for BT Wholesale/HIPCOM SIP Trunk Service and Avaya IP Office 8.0 Issue 1.0 Abstract These Application Notes describe the procedures for configuring
Implementing Cisco IOS Telephony and Unified Communications Express (IITUCX)
Implementing Cisco IOS Telephony and Unified Communications Express (IITUCX) Course Objectives Explain the benefits and components of a Cisco Unified Communications system Describe how traditional telephony
Deployment options for Avaya Communicator for Microsoft Lync with Lync Peer to Peer calling enabled
White Paper Deployment options for Avaya Communicator for Microsoft Lync with Lync Peer to Peer calling enabled Abstract This white paper describes the procedure to enable Microsoft peer to peer calling
CVOICE - Cisco Voice Over IP
CVOICE - Cisco Voice Over IP Table of Contents Introduction Audience At Course Completion Prerequisites Applicable Products Program Contents Course Outline Introduction This five-day course covers the
Jabber 10.6. Client Update. February 2015 issue 0.6
Jabber 10.6 Client Update February 2015 issue 0.6 Introducing Cisco Jabber 10.6 Clients Jabber 10.6 is the latest release of Cisco Unified communication client The release is available across all platforms
Hosted VoIP Phone System. Admin Portal User Guide for. Call Center Administration
Hosted VoIP Phone System Admin Portal User Guide for Call Center Administration Contents 1 About this Guide... 4 2 Accessing the Hosted VoIP Phone System Administration Portal... 5 3 Hosted VoIP Phone
NovaTec release information firmware 00.06.07.00
NovaTec release information firmware 00.06.07.00 2 Known Issues None. The firmware now needs a valid firmware license to activate telephony functions. Without a valid license a system running firmware
Technical Configuration Notes
MITEL SIPCoE Technical Configuration Notes Configure Mitel UC360 SIP Phone and Mitel MCD for use with VidyoWay SIP CoE 13-4940-00228 NOTICE The information contained in this document is believed to be
MITEL SIP CoE Technical. Configuration Note. Configure Mitel MiVoice Business 7.2 SP1 PRI for use with IntelePeer SIP Trunking. SIP CoE XXX
MITEL SIP CoE Technical Configuration Note Configure Mitel MiVoice Business 7.2 SP1 PRI for use with IntelePeer SIP Trunking SIP CoE 12-4940-00XXX NOTICE The information contained in this document is believed
Cisco Unified Communications 500 Series
Cisco Unified Communications 500 Series IP PBX Provisioning Guide Version 1.0 Last Update: 02/14/2011 Page 1 DISCLAIMER The attached document is provided as a basic guideline for setup and configuration
Dial Peer. Example: Dial-Peer Configuration
Configuring Dial Peers Understanding Dial Peers This topic describes dial peers and their applications. Understanding Dial Peers A dial peer is an addressable call endpoint. Dial peers establish logical
MiCloud Telepo for Desktop 4.5
MiCloud Telepo for Desktop 4.5 Key Features MiCloud Telepo application for PC and Mac Branded to the service provider Dedicated communication environment for desktop or laptop Wide range of advanced unified
Motorola TEAM WSM - Cisco Unified Communications Manager Integration
Motorola TEAM WSM - Cisco Unified Communications Manager Integration Summary This setup covers the of the TEAM VoWLAN solution with a Cisco Unified Communications Manager 7.1.2. This integration will be
MITEL SIP CoE. Technical. Configuration Notes. Configure Ascom i62 phones for use with MiVoice Office. SIP CoE 14-4940-00310
MITEL SIP CoE Technical Configuration Notes Configure Ascom i62 phones for use with MiVoice Office SIP CoE 14-4940-00310 NOTICE The information contained in this document is believed to be accurate in
nexvortex SIP Trunking Implementation & Planning Guide V1.5
nexvortex SIP Trunking Implementation & Planning Guide V1.5 510 S PRING S TREET H ERNDON VA 20170 +1 855.639.8888 Introduction Welcome to nexvortex! This document is intended for nexvortex Customers and
Administration. Avaya Business Communications Manager Find Me/Follow Me. Introduction. Find Me/Follow Me Fundamentals
Avaya Business Communications Manager Find Me/Follow Me Administration Introduction Find Me/Follow Me allows simultaneous ringing on up to five different external destinations. Users and administrators