1 Atlanta RV Rental Folding Camper Photos An addendum to Manual.
2 Setting up unit. Rotate Tongue Jack and Lower. Disconnect Electric Cord and Chains and Brake-Away cable from Vehicle.
3 Get Key, Wheel Chocks, Lug wrench, and jack handle from Tongue Tool Box. Place Wheel chocks on wheels, 2 per wheel (front and back) Connect Battery
4 Swing Down Style Jacks Turn on Propane Tank
5 Unlock Door
6 Swing Door Open and latch open. Pull Doorstep out by raising edge and pulling out.
7 Door step in lowered position. Prior to raising roof, unlatch all four corner latches. Use crank handle to raise roof to fully raised position. Proceed slowly and stop if any bind is encountered.
8 After roof is raised, lower stabilizer jacks. Put down rear jacks first before entering vehicle. Then put down front jacks. After jacks are lowered, use lug wrench to tighten. Snug only, do not use to level unit! Set up with all 4 jacks down.
9 Pull out front bed and lower bed support rails. Attach to frame rail studs. Pull out rear bed and lower bed support rails. Attach to bumper studs. Detail of attachment to bumper.
10 With beds fully out, attach all bungee cords to secure tent fabric under edge of beds. REMEMBER TO UNHOOK THESE BEFORE BEDS ARE PUT BACK! EXPENSIVE DAMAGE WILL OCCUR TO TENTING FABRIC! Bungee
11 Bungee Bed Bow Supports stored under mattress. Bed Bow Supports stored under mattress.
12 Use bed bow supports to push out bed bows, and attach at ceiling as shown. Bed bow attachment at ceiling. MAKE SURE TO REMOVE BED BOW SUPPORTS PRIOR TO PUSHING BEDS IN ON TAKE-DOWN! DAMAGE WILL OCCUR!
13 Galley in travel position
14 Galley Raise Lower Instructions Raise Galley into position. Galley in use position.
15 Stove Lighting stove Turn on Water Pump switch. Turn OFF when traveling.
16 Air Conditioner Air Conditioner cord stows at ceiling under curtain with VELCRO. MAKE SURE TO STOW ON TAKE-DOWN BEFFORE PUSHING IN BEDS. At set-up Plug in A/C power cord in outlet. Air Conditioner cord stows at ceiling under curtain with VELCRO. MAKE SURE TO STOW ON TAKE-DOWN BEFFORE PUSHING IN BEDS.
17 To lower screen door, first release two snap straps. Release screen door from ceiling above door by pushing down on release pin and pulling door away from wall.
18 Slowly lower door into door frame, being careful not to scratch countertops with lower edge of door as it is lowered. Place screen door lower edge in slot by door opening. Push screen door in at top and secure with two latches under curtain above door.
19 Attach Velcro along sides of door frame to seal tent.
20 Sink Drains here, remove cap before using sink. Hook up water hose and regulator here. Connect Electric Cord in 30A Receptacle. A 30A to 15A adapter is included in the kit.
21 Refrigerator controls in ventilated compartment on street side of unit. To run Refrigerator on 120V Electric, press green switch to ON To run Refrigerator on Propane, Turn on Gas knob, Press and hold Grey knob and press Red igniter repeatedly until it lights.
22 Taking Down Unit Place cap on sink drain Remove, drain and stow water hose and regulator here with ends screwed together. Disconnect Electric Cord and stow.
23 REMEMBER TO UNHOOK all bungee cords BEFORE BEDS ARE PUT BACK! EXPENSIVE DAMAGE WILL OCCUR TO TENTING FABRIC! Bed Bow Supports stored under mattress. Use bed bow supports to push out bed bows, and attach at ceiling as shown.
24 Slowly lower door into door frame, being careful not to scratch countertops with lower edge of door as it is lowered. Secure door to ceiling with two snap straps.
25 Secure door to wall above door with bracket and pin. Place Galley in travel position WIPE UP ANY WATER THAT SPILLS FROM SINK ON FLOOR!
26 Galley Raise Lower Instructions Air Conditioner cord stows at ceiling under curtain with VELCRO. MAKE SURE TO STOW BEFORE PUSHING BEDS IN! Another REMINDER - REMEMBER TO UNHOOK all bungee cords BEFORE BEDS ARE PUT BACK! EXPENSIVE DAMAGE WILL OCCUR TO TENTING FABRIC!
27 Raise and stow bed support rails. Slowly push in front bed. Fold tenting neatly on top of bed as it slides in. Raise and stow bed support rails. Slowly push in rear bed. Fold tenting neatly on top of bed as it slides in.
28 Turn off Propane Tank HAVE REFILLED BEFORE RETURNING UNIT! Before lowering roof, release all jacks.
29 Before roof is lowered, stow stabilizer jacks. Before lowering roof, close lower door.
30 Use crank handle to lower roof to fully closed position. Proceed slowly and stop if any bind is encountered. Neatly stuff tenting in as roof is lowered. Stow Doorstep out by raising edge and pushing in. After roof has been lowered and all tenting secured inside, latch all four corner latches before towing.
31 Before towing, always check lug nuts for tightness. Disconnect Battery Place Key, Wheel Chocks, Lug wrench, and jack handle in Tongue Tool Box.
32 Connect Electric Cord and Chains and Brake-Away cable to Vehicle. Secure Hitch ball with pin. Rotate Tongue Jack and Raise. WALK AROUND VEHICLE AND MAKE SURE ALL JACKS ARE UP, ROOF IS LATCHED, TOOL BOX IS LOCKED, CHOCKS ARE STOWED, TIRES ARE GOOD, LUG NUTS ARE TIGHT, ETC.
END DUMP OPERATION MAINTENANCE & PARTS MANUAL INDEX PAGE # i. CONSUMER INFORMATION ii. GENERAL OPERATION INSTRUCTIONS iii. DUMPING OPERATION INSTRUCTIONS iv. BLANK SECTION ONE 1-1 LUBRICATION CHART AND
USDA FOREST SERVICE APPARATUS BODY ONLY SPECIFICATION TYPE 6 FIRE APPARATUS MODEL 643U MAY 2013 Model 643U Body Only 1 Supersedes August 2011 USDA Forest Service Specification: Specification Type: Type
X9 FOLLOW OWNER S MANUAL & USER GUIDE IMPORTANT INFORMATION BLUETOOTH SIGNALS : The Bluetooth module DW-BTM-222 used in this product is a Class 1 device, subclass 22; Wide Band Data Transmission Systems
encor! enetworks TM Version A.2, January 2013 2013 Encore Networks, Inc. All rights reserved. Changing the SIM in a BANDIT Product s GSM Card Wireless connections use radiofrequencies (RFs) through airwaves
INSTALLATION & OPERATION MANUAL FLIGHT TYPE DISHWASHERS MODELS STPC STPCW STPCW-D STBUW For additional information on Stero or to locate an authorized parts and service provider in your area, visit our
(Body Accessories & Dimensions) After Sales Service Department of Chery Automobile Co.,Ltd. Contents Chapter I Engine Hood & Luggage Boot...1 I. Removal and Installation of Engine Hood...1 1. Preparations...1
System One Heated Humidifier USER MANUAL 2009 Respironics Inc. and its affiliates. All rights reserved. Table of Contents Intended Use... 2 Warnings... 2 Cautions... 2 Symbol Key... 2 System Features and
Pro Series C11 Combination Primary and Backup Sump Pump System Instruction Manual & Safety Warnings Table of Contents Important Safety Warnings and Instructions Electrical precautions 1 Battery preparation
GENERAL VALVE Twin Seal Double Block and Bleed Plug Valve GENERAL VALVE 2 TABLE OF CONTENTS GENERAL VALVE TWIN SEAL Installation.... 4 Operation.... 5 Series 400, 800 & 900 Integral Bushing/Retained Ring
Therapy System User Manual September 2007 340075 Rev D ! WARNING Important Safety Information accompanies this device. Indications, Contraindications, Warnings, Precautions and other Safety Information
installation guide ACTIV- Base foot. Leg x columns - right & left Motor unit. Work surface supporting bracket (Cantilever) x Control. box Base foot x Handset 4. Phase Motor unit Materials and Tools Hardware
EARTHQUAKE SAFETY IN THE WORK PLACE COMPANY PLANS All companies have an obligation to their employees to maintain a disaster plan. An emergency evacuation area must be designed, a nearby safe area, preferably
Installation Manual 4414000B Model 441 Battery Backup System *Do not throw away or lose this manual. IMPORTANT: Prior to installation, record Model, Serial Number, and Code Number from pump nameplate for
FORWARD CONTENTS HOW TO USE THIS MANUAL SERIAL NUMBER Quad Lander 250 SERVICE MANUAL Homepage Contents FORWARD This service manual contains the technical data of each component inspection and repair for
ADI 3059-B Certified ISO 9000 MANI-FLEX AutoSwitch Automatic and Semi-Automatic Switchover Systems INSTALLATION AND OPERATION INSTRUCTIONS Before Installing or Operating, Read and Comply with These Instructions
Hot-End Replacement Guide BFB 3000 plus & 3D Touch Pre assembly checks: Testing the hot-end before fitting: Check the heating cable: Set the multi-meter to read resistance (2000 ohms) Test the two outside
OPERATIONS AND MAINTENANCE INFORMATION FOR: THE CANPLAS BACKWATER VALVE THE CHEMTROL BALL SHUT OFF VALVE SUMP PUMPS AND WASTEWATER EJECTOR PUMPS THE LOUISVILLE AND JEFFERSON COUNTY METROPOLITAN SEWER DISTRICT
Model J3.1 Owner's Manual Sealweld ACTIV-8 Gun By Sealweld Corporation We trust you will find the lessons detailed in this program useful when maintaining the valves at your facility. Should you have any
Instruction Manual for 9018 Quick Hoops High Tunnel Bender Copyright 2014 Johnny s Selected Seeds. All rights reserved. 955 Benton Ave., Winslow, ME 04901 Phone: 1-877-564-6697 Fax: 1-800-738-6314 Email:
Owner s Operator and Maintenance Manual Get-U-Up Lift DEALER: This manual MUST be given to the user of the patient lift. USER: BEFORE using this patient lift, read this manual and save for future reference.
Installation Manual with Service Replacement Parts For Champion Models: DH-1000, DL-1000 Moyer Diebel Models: MD1000HT, MD1000LT Valu-Clean Models: VC1000, VC1000HT Door-type Dishwasher Model: 1000 Series