Computational Fluid Dynamics Investigation of Two Surfboard Fin Configurations.

Size: px
Start display at page:

Download "Computational Fluid Dynamics Investigation of Two Surfboard Fin Configurations."

Transcription

1 Computational Fluid Dynamics Investigation of Two Surfboard Fin Configurations. By: Anthony Livanos ( ) Supervisor: Dr Philippa O Neil Faculty of Engineering University of Western Australia

2 For the fin fanatics of Swaylocks. 2

3 Contents Page Introduction 4 Hydrodynamic Forces.7 CFD Analysis Observations..12 Conclusion & Review..18 Appendix 20 Bibliography..22 3

4 Introduction As the sport of surfing is continually evolving, surf riding equipment is steadily improving. The surfing industry has lead the surfboard to develop from its origins of tree trunks to highly sophisticated composite structures. The professional competitive nature of surfing pushes the performance limits higher and higher. There are many variables involved with surfboards and fins in terms of performance such as wave size, board size and the surfer s ability. All components are inter related and must be optimised as a group, to satisfy the conditions they are being used in and to reach the desired performance. All the thousands of variables and the definitions of performance make the analysis and comparison of surfboards and fin configurations very difficult. For the purpose of this report, only two different fin configurations have been investigated, the Thruster setup (three fins) and the Single fin setup. The two side fins of the Thruster setup were FCS G5 fins, whilst the rear was an FCS G3000 fin. The fin used for the single fin setup was the JB2 single fin. Both configurations have been put under the same flow conditions. There is limited experimental evidence available for the relative speeds involved in surfing. For the purpose of this report, a speed of 6 m/s of water relative to the fin has been used in the analysis. Surfboards typically encounter large angles of attack and significant change in directions. This report only simulates straight line flow as the dynamic simulation of turning and manoeuvres is beyond the scope of this report. To simulate the presence of the surfboard, the fins have been modelled in a rectangular domain, attached to a wall surface, representing the bottom of the surfboard. Since the fin chords are in the order of 0.1m, consequently chord calculated Reynold s numbers will be in the order of In this range, separation and boundary layer effects are known to be significant. It is expected the flow will be turbulent with vortices present. The ultimate goal of this report is to qualitatively investigate the hydrodynamic forces, and fluid behaviour surrounding two different surfboard fin configurations. 4

5 The fin properties, configurations and dimensions used in the analysis are as follows: Figure 1. Thruster and Single fin configurations Figure 2. Front view of Thruster setup depicting Cant. Figure 3. Top view of Thruster setup depicting Toe In. 5

6 Figure 4. Thruster setup analysis domain. Front and Side view. Figure 5. Single fin setup analysis domain. Front and Side view Fin: JB2 Single Fin FCS G5 FCS G3000 Base Chord (mm): Surface Area (mm ²): , , , 730 Volume (mm ³): 235, , , 180 Aspect Ratio: Base Thickness/Chord Length ratio (%): Table 1. Summary of Surfboard fin properties 6

7 Hydrodynamic Forces Performance in regards to surfboard fins is not easy to define. Performance is based on a wave-to-wave and surfer-to-surfer basis. Some fins work well in bigger waves, and some fin properties are good for beginners rather than professionals. Fundamentally, the purpose of surfboard fins is to provide greater control over the surfboard. A greater understanding of the hydrodynamic forces acting on surfboard fins would provide an insight into how to maximise certain properties of the fins in order to achieve greater performance levels. Since fins are foiled bodies, with a large range of angle of attack, they will experience a lifting force acting perpendicularly to the flow, and a drag force acting in parallel with the flow. For visualisation purposes, since the fin is oriented in the vertical plane, the forces will act in primarily the horizontal planes. Drag forces: The total drag force acting on a body immersed in a fluid is comprised of three different types of drag: Form (or pressure), Skin Friction (or viscous), and Induced. Form drag is a result of the difference between the high pressure regions at the leading edge, and the low pressure regions associated with the trailing edge(s). The differences in pressures can be reduced through efficient streamlining of the immersed fin. Studies have shown streamlining the leading edge reduces drag by 45%, whilst streamlining the trailing edge reduces drag by up to 85%. Rounded leading edges prevent early flow separation, as pre-mature flow separation will lead to the fin stalling and reducing lift dramatically. Figure 6. Lift and Drag forces. 7

8 Skin friction drag is caused by the physical contact between fin and water molecules. This form of friction is similar to the friction between two bodies. Since the friction is between a solid and a fluid the properties of both the solid and fluid will determine the magnitude of the friction. The surface roughness is a factor affecting friction in terms of the solid fin, and for the fluid it is the fluid s viscosity dictating the friction. Since the viscosity cannot be changed, changes to the fin surface such as a matte finish or a gloss finish will alter performance. Along the surface of the fin, a low energy flow region exists known as the boundary layer. The magnitude of skin friction also depends on the state of the boundary layer. Boundary layer and fluid interactions are usually beneficial since the friction between boundary layer and fluid is less than fluid and solid. One method of inducing and retaining boundary layers would be to roughen the surface of the fin, initiating turbulent flow, which is less prone to flow separation, consequently forming a boundary layer. Induced drag is mainly concerned with the formation of vortices at the fin tips. Vortices are spiralling bodies formed by the leaking of pressures at the tip of the fin. A vortice is formed when the high pressure underneath the fin curls around the wing tip to the top side of low pressure. Consequently, the overall pressure above the fin is reduced, and this dramatically reduces the lift generated. Vortices can be reduced in a few ways. Shortening the chord length will reduce vortices as it provides less opportunity for the formation of vortices. Fins of higher aspect ratios are more efficient because the load bearing distribution is concentrated further away from the tips. Since less load is distributed to the tips vortices are reduced. The introduction of a physical barrier, such as tips on airplane wings also prevents and interrupts the formation of vortices. In summation, total drag = parasitic drag (form and skin) + induced. Ideally total drag must be minimised to increase performance, but there are other factors to consider. Certain drags contribute directly to loss of speed, whilst others contribute to fin stability and suck, which are responsible for control and responsiveness of the board on the wave surface. Which drags are positive or negative is another debate in itself, and subject to opinion without the presence of proper evidence. 8

9 A qualitative comparison of drag occurring in the two fin configurations can be done using the information given in Table 1. Since the Thruster setup consists of two G5 fins and one G3000, the total surface area and volume is mm ² and 158, 780 mm ³ respectively. For the Single fin setup, we have a total surface area of 47, 600 mm ² and volume of 235, 380 mm ³. From this data and assuming that all fins have the same surface roughness, since the Thruster setup has more wetted surface area, it would possess more Skin friction drag than the single fin setup. From the data it can be observed that the Single fin occupies a larger volume compared the Thruster setup. Theoretically form drag relates to volume but there are other factors involved. The single fin is larger, but has no Cant or Toe-In to add to drag forces. In the simple straight line flow analysis, the Thruster setup would have more form drag due to the side fins being Canted at 4 and having a 3.5 Toe-In. In terms of Induced drag, the strength and number of vortices must be considered. The Thruster setup will generate three vortices as compared to the single vortice created by the single fin. It can be assumed that the total induced drag would be more for the Thruster setup. Further investigation with CFD will clarify this issue later in this paper. Lift forces: There are quite a few explanations of lift published in resources and available on the internet. Unfortunately, theories are mis-applied and lead to incorrect theories being widely accepted. Theories of lift have been the source of many arguments. The primary reason for this is people choose to believe either a Newtonian point of view, or a Bernoullian point of view. Incorrectly applying Bernoulli s theory leads us to the theory which is known as the "equal transit time" or "longer path" theory. This theory states that foiled bodies are designed with the upper surface longer than the lower surface in order to generate higher velocities on the upper surface because the molecules of gas on the upper surface have to reach the trailing edge at the same time as the molecules on the lower surface. From Bernoulli, pressure of a fluid is inversely proportional to velocity. The incorrect theory then invokes Bernoulli's equation to explain lower pressure on the upper surface and higher pressure on the lower surface resulting in a lift force. 9

10 The correct theory of lift is based on flow turning and is actually a combination of both Bernoullian and Newtonian views. When a body is immersed in a moving fluid, the fluid flows around it, with varying velocities depending on shape, size and drag factors. This variation in flow velocities causes variations in pressures. Integrating the pressures over the entire body, not just the top side, equates to the total hydrodynamic force acting on the body. This hydrodynamic force is comprised of lift, perpendicular to the flow direction, and drag, parallel to the flow direction. This makes the basis for the Bernoullian part of lift. The Newtonian part is based around Newton s third law of action and reaction. Since this hydrodynamic force is acting on the solid body, the solid body must also be acting on the fluid with the same force. This force acts to turn or deflect the fluid. So in essence, both Bernoulli and Newton are correct. Factors affecting the generation of lift are grouped into two categories; Object and Fluid. In relation to the object, shape and size will affect the generation of lift. In terms of a fin, this relates to the fin s foil, thickness, and camber. Over all plan form shape will also affect the lift generated. Plan form of fins can vary in terms of rake and depth. The discussion of how these factors affect the fin are not relevant as the testing is only being done on two sets of fins, with shape and size being constant. Hydrodynamic forces are definitely proportional to surface area of the fins. The Coanda effect is definitely an important consideration in regards to analysis of forces on foiled bodies. The Coanda effect states that a moving stream of fluid in contact with a curved surface will tend to follow the curvature of the surface rather than continue to travel in a straight line. Relating back to the theory of lift, this effect would essentially aid in turning the air, thus creating more lift. Certain foils would lead to a more pronounced Coanda effect and consequently more lift. Figure 7. Cross section of a foil, depicting Coanda Effect 10

11 With regards to the fluid factors, properties such as viscosity, mass of fluid and velocity of the fluid relative to the immersed body all contribute to the generation of lift. The velocity of the fluid is constant for both trials, but it is known that higher velocities correlate to larger hydrodynamic forces. Fluid viscosity and velocity in terms of surfing are all dictated by the waves and oceans. Since these are constants, other factors must be optimised to achieve greater lift performance. The Thruster setup derives its name due to the fact it provides a forward thrust. This thrust comes from the two side fins. The overall lift force on the fin is biased slightly forward on an asymmetrical fin to begin with due to the foil. Increasing the Toe-In angle increases forward thrust to an extent, until the fin reaches a stall angle. At this point flow separates from the fin and reduces the lift dramatically. Since the Single fin setup is only one fin, with no Cant or Toe-In, it will be producing less lift as opposed to the Thruster setup. The Thruster setup will be providing more lift, but also has increased drag, consequently reducing the lift. Figure 8. Vector forces of the side fins providing the forward thrust. 11

12 CFD Analysis Observations Computational Fluid Dynamics (CFD) is the of computers to help analyse and visualise problems in fluid dynamics. CFD can be used in many applications. For the purpose of this report, CFD will provide information to help visualise the fluid dynamics involved with two different fin configurations. A wide range of information can be extracted using CFD, in both numerical and graphical data. Caution has to be exercised in order to not make first impression assumptions when considering images and data because they can be mis-leading. The results of CFD analysis of both the Thruster and Single fin configurations are depicted below. Form Drag: The first set of images is useful to investigate the form drag present in both fin configurations. Extreme form drag would be evident with a very high pressure at the leading edge of the object, and a very low pressure at the trailing edge. From these images it can be seen that a concentrated high pressure exists before the single fin. Figure 9. Single fin plane cut depicting pressures. Figure 10. Thruster plane cut depicting pressures. 12

13 The Thruster setup also has high pressure build up at the leading edge of all fins, but it is somewhat larger. The inherit angle of attack of the side fins due to their Toe-In could be the contributing factor. Both sets of fins do not display obvious low pressures behind the fins. This is most likely a result of the fins having an efficient trailing foil, reducing the low pressure behind the fin. Since the Single fin has a lower average pressure at the leading edge, and with both side fins contributing heavily to form dram on the Thruster setup, it can be confirmed that the Single fin has less form drag. Skin Friction and the Boundary Layer: Certain Skin friction configurations would lead to types of Boundary layers being formed. A rougher skin would induce turbulent flow, and consequently reduce the chance of flow separation on the fin. Certain Boundary layer configurations have been used to achieve reduced drag in similar sports, such as skins on the hulls of yachts racing in the America s Cup. CFD is able to provide us with physical properties of the boundary layer such as fluid velocity within the boundary layer, and size of the boundary layer itself. Figures 11 & 12 provide us with valuable information in regards to the shapes and sizes of the boundary layers of the different fins. Figure 11. Single fin plane cut, depicting velocity boundary layer profile Figure 12. Thruster plane cut, depicting velocity boundary layer profile 13

14 From Figure 11 it can be seen that the boundary layer exists mainly the concave formed by the rear half of the fin foil. The Thruster side fins have a different shape, with the boundary layer being formed around the outside and inside edges, all over the fin. CFD would be a useful tool in analysis of boundary layers, because with the aid of probe lines, the exact profile of the boundary layer can be seen. This would be beneficial in running one test, then slightly changing a variable, for example surface roughness, and then running the same test, and viewing the subsequent profiles. Probe lines have been placed on the surface of the Single fin, and the side and centre fins of the Thruster setup. The probe lines extend out from the fin s surface about 10 12mm, and the velocity profiles are depicted in the graphs below. Graph 1 is a plot of three line probes in the Thruster fin setup. One exists on the centre fin (dark blue), another on the curved foil of a side fin (light blue) and the third on the flat side of a side fin (green). Graph 2 indicates the line probes on the Single fin. Graph of Probe Line on Centre and Side fin of Thruster Setup Velocity (m/s) 4 3 Centre BL Curved Foil Side BL Flat Foil Side BL Probe Line Length (mm) Graph 1. Boundary Layer Investigation of Thruster Setup 14

15 Graph of Line probe in Single Fin Boundary Layer Velocity (m/s) Probe Line Length (mm) Graph 2. Boundary Layer Investigation of Single Fin Setup From the graphs it can be seen that the boundary layer profiles are of similar shape. Boundary layers are zones of flow close to the surface of bodies where the velocity drops dramatically. The boundary layers associated with the Thruster setup can be seen to drop dramatically between 0 and 1mm from the surface of the fins. From Graph 2, the boundary layer of the Single fin drops dramatically between 0 and 0.5 mm. This data indicates that the boundary layer associated with the Single fin is only half as thick as the boundary layer of the Thruster fins. An interesting result can be seen in the differences between boundary layer profiles on either side of the side fin in the Thruster setup. It can be seen that both have a boundary layer thickness of around 1mm, but the gradient of the lines after this point is different. The gradient of the flat side of the fin is a lot less, indicating that the velocity of the flow increases a lot slower as you move away from the fin from the flat side. The curved foil side has a higher gradient, and reaches a maximum quicker. This data confirms Bernoulli s principle in relation to speed differences observed over asymmetrically foiled bodies. 15

16 Induced Drag (Vortices): A major part of the control and board stability in relation to fins has to do with the formation, location and behaviour of trailing vortices. Through the mapping of particle flow trajectories in CFD we are able to visualise and gather data on the properties of the vortices formed. Similar experiments can be carried out in real life, with wind tunnels and smoke trails. From suggested theories and knowledge, we expect the formation of vortices to be located mainly around the tip of the fins. In Figure 13, we can see the formation of a tip vortice. Since the fin is symmetrically foiled, two vortices are seen at the tip of the fin, as shown in Figure 14. Figure 13. Side view of Single fin flow trajectories. Tip vortice highlighted in red. Figure 14. Rear view of Single fin tip. Arrows indicate vortice rotation. It is known that the strongest vortices are shed at the tips, but are not the only place vortices can exist. Figure 15 shows a rather surprising result. Figure 15 depicts the velocity isosurfaces related to the Thruster setup. Vortices are shown as the long spikes protruding from the rear of the fin. The surprising result comes from the fact there is two major vortices forming on the two side fins, one near the top, and one near the base of the fins. The centre fin also possesses a vortice, but it is located at the base, rather than the tip. The centre fin doesn t have the same amount or sized vortices compared to the side fins. 16

17 Figure 15. Velocity isosurfaces depicting the formation of trailing vortices. Figure 16. Rear view of Thruster fins. Flow trajectories map the rotation of trailing vortices. From rough measurements of the flow trajectories, it can be seen the diameter of the tip vortice is around 11 mm for the Single fin, and 40 mm for the side fins of the Thruster setup. The size of the vortice is proportional to its strength, if measured in the same conditions. Higher flow rates would pertain to smaller diameters in vortices. The foil of the fin and its plan form shape, especially at the tip, will affect the location and strength of vortices. Drag relates proportionally to the percentage of the fin affected by vortices. Larger fins with smaller vortices located closer to the tips would have less induced drag, as opposed to smaller fins with more vortices. Consequently the Single fin would have less induced drag. Since the Thruster setup possess stronger and more vortices, it offers more control and hold on the wave face. From the above results of CFD, it can be confirmed that the Thruster setup does possess a higher overall drag force than the Single fin setup, in a straight line simulation. Whilst this is the case, other factors complicate the investigation such as lift and angles of attack during high speed manoeuvres. The real world evidence suggests there is more to the story since most professionals use a variation of the Thruster setup during competition. To improve this investigation, a more quantitative analysis can be done using complex mathematics and more accurate CFD. 17

18 Conclusion & Review Historically, a major part of the development of surfboards and fins involve the shapers and the feedback received from professional surfers. A large influence on the design relates to aesthetic considerations and perceived market expectations. The trial and error method has yielded impressive results in terms of performance, yet the introduction of technology and CFD analysis is beginning to be more widely accepted. Beyond the argument of reality against virtual simulation, the surfing industry is starting to realise CFD as yet another tool to investigate and refine the performance variables of surf craft. Due to the number of variables involved with fin performance, CFD becomes extremely useful. The ability to slightly change one variable, such as foil, and to then run the exact same flow simulation under the exact same conditions yields more efficient and accurate results, allowing the user to properly investigate relations between variables. Combining CFD, and real life experimentation on waves would be an unstoppable combination on the path to advancing performance in surfboards and their fins. This investigation has helped to visualise flow theories and confirm fluid behaviour surrounding two different surfboard fin configurations. In my opinion, this method can be improved in a variety ways. Firstly the modelling method I used was the cross sectional profile and loft method. More accurate models can be made incorporating NACA formulas to define the foils entirely. In terms of the CFD software itself, perhaps using more scenario specific software would be more appropriate. Using more powerful computers to calculate the simulation to a higher resolution would also aid in the accuracy of results. A paper report provides limited information. To fully understand and visualise the models need to be viewed in 3D and animations. For this purpose, I have placed a variety of animations and extra images on the internet. They are located at the following address: 18

19 My recommendations for future work would revolve around the dynamic simulation of the surfboard on a water surface, eventually simulation of a wave. Being able to model real life manoeuvres and not just straight line flows would be incredibly useful. To model the wave alone is a massive challenge. On top of this to model the interaction of a surfboard and its fins, whilst measuring values and calculating flows is a very difficult task. Similar work has been done with ships and dynamic simulations of wave impacts and forces, so it is not completely a pipe dream to envisage dynamic simulation of a surfboard and wave. 19

20 Appendix Airfoil: An airfoil or aerofoil is a part or surface, such as a wing, propeller blade, or rudder, whose shape influences control, direction, thrust, lift, or propulsion. Angle of attack: The angle between an airfoil or wing and the direction of the fluid relative to it. Aspect Ratio: The ratio of the fin depth to the chord length Bernoulli's Principle: Bernoulli's Principle states that an increase in the velocity of a fluid is always accompanied by a decrease in pressure. Boundary Layer: A layer of static to slow moving fluid adjacent to the surfaces of a moving body. Cant: The angle of a surfboard fin in relation to the vertical plane. Centreline: A line of symmetry along the axis of an object. Coanda Effect: The Coanda Effect states that a moving stream of fluid in contact with a curved surface will tend to follow the curvature of the surface rather than continue to travel in a straight line. Computational Fluid Dynamics (CFD): The use of computers to analyse problems in fluid dynamics. Cross-sectional area: The area of a two dimensional slice of a three dimensional object. Drag: Any force that creates resistance to motion. Dynamic pressure: The pressure of a fluid in motion, measured by the pressure it exerts on a flat surface. Fluid: A liquid or gas that flows and assumes the shape of its container. 20

21 Foil: A foil is a surface designed to maximize lift while minimizing drag in a given range of conditions. Form drag: Form drag, also called profile drag or wind resistance, is the drag force created on a body as it displaces the fluid through which it moves. If moving forward, form drag results in greater air pressure at the front of the body than at the rear. Isosurface: A type of display that shows a 3D surface for a given value Lift: Aerodynamic forces that support a vehicle solely due to airflow or pressure. Pressure: The force exerted on a surface per unit area of the surface. Single fin setup: One-fin surfboard design dating back to the first use of the fin on a surfboard (by Tom Blake of the USA in the 1930s) Static pressure: The pressure of a stationary fluid. Thrust: A force that produces motion. Thrust can result from the displacement of a fluid. Thruster setup: Three-fin surfboard design created by Simon Anderson of Australia in 1980; now the most common fin setup used by surfers. Toe-In: The angle of a surfboard fin, in relation to the angle made with the centre line of the board. Velocity: The speed in a given direction; a vector quantity. Vortice: A vortice is a spinning, often turbulent, flow (or any spiral motion) with closed streamlines. 21

22 Bibliography 1. White, F. M 2003, Fluid Mechanics, University of Rhode Island, Kingston. 2. Lavery, N. 2005, Optimisation of Surfboard Fin Design for Minimum Drag by Computational Fluid Dynamics in The 4 th International Surfing Reef Symposium, Natural And Artificial Surfing Reefs, Surf Science, and Coastal Management. Manhattan Beach, California. 3. Hendricks, T. 1969, Surfboard Hydrodynamics, Part I: Drag, Surfer, Vol. 9, No Hendricks, T. 1969, Surfboard Hydrodynamics, Part II: Pressure, Surfer, Vol. 10, No Hendricks, T. 1969, Surfboard Hydrodynamics, Part III: Separated Flow, Surfer, Vol. 10, No Paine, M. 1974, Hydrodynamics Of Surfboards, Final Year Thesis, Bachelor of Mechanical Engineering, University Of Sydney 7. Rosen, B., Laiosa, J. 2000, CFD Design Studies for America s Cup 2000, In Proc. of AIAA Benson, T. 2006, Guided tours of the BGA, [Online], N.A.S.A. Available from: 9. Preston, R. 2005, Pressure Drag, [Online], Available from: Lavery, N. 2006, S.U.R.F.S, [Online], Available from: Paler, M. 2006, How Important is Lift in Fins?, [Online], Swaylocks. Available from: ;post=261303;page=1;sb=post_latest_reply;so=asc;mh=25; 22

QUT Digital Repository: http://eprints.qut.edu.au/

QUT Digital Repository: http://eprints.qut.edu.au/ QUT Digital Repository: http://eprints.qut.edu.au/ El-Atm, Billy and Kelson, Neil A. and Gudimetla, Prasad V. (2008) A finite element analysis of the hydrodynamic performance of 3- and 4-Fin surfboard

More information

Lift and Drag on an Airfoil ME 123: Mechanical Engineering Laboratory II: Fluids

Lift and Drag on an Airfoil ME 123: Mechanical Engineering Laboratory II: Fluids Lift and Drag on an Airfoil ME 123: Mechanical Engineering Laboratory II: Fluids Dr. J. M. Meyers Dr. D. G. Fletcher Dr. Y. Dubief 1. Introduction In this lab the characteristics of airfoil lift, drag,

More information

Application of CFD Simulation in the Design of a Parabolic Winglet on NACA 2412

Application of CFD Simulation in the Design of a Parabolic Winglet on NACA 2412 , July 2-4, 2014, London, U.K. Application of CFD Simulation in the Design of a Parabolic Winglet on NACA 2412 Arvind Prabhakar, Ayush Ohri Abstract Winglets are angled extensions or vertical projections

More information

Practice Problems on Boundary Layers. Answer(s): D = 107 N D = 152 N. C. Wassgren, Purdue University Page 1 of 17 Last Updated: 2010 Nov 22

Practice Problems on Boundary Layers. Answer(s): D = 107 N D = 152 N. C. Wassgren, Purdue University Page 1 of 17 Last Updated: 2010 Nov 22 BL_01 A thin flat plate 55 by 110 cm is immersed in a 6 m/s stream of SAE 10 oil at 20 C. Compute the total skin friction drag if the stream is parallel to (a) the long side and (b) the short side. D =

More information

NUMERICAL ANALYSIS OF THE EFFECTS OF WIND ON BUILDING STRUCTURES

NUMERICAL ANALYSIS OF THE EFFECTS OF WIND ON BUILDING STRUCTURES Vol. XX 2012 No. 4 28 34 J. ŠIMIČEK O. HUBOVÁ NUMERICAL ANALYSIS OF THE EFFECTS OF WIND ON BUILDING STRUCTURES Jozef ŠIMIČEK email: jozef.simicek@stuba.sk Research field: Statics and Dynamics Fluids mechanics

More information

Using CFD to improve the design of a circulating water channel

Using CFD to improve the design of a circulating water channel 2-7 December 27 Using CFD to improve the design of a circulating water channel M.G. Pullinger and J.E. Sargison School of Engineering University of Tasmania, Hobart, TAS, 71 AUSTRALIA Abstract Computational

More information

Basics of vehicle aerodynamics

Basics of vehicle aerodynamics Basics of vehicle aerodynamics Prof. Tamás Lajos Budapest University of Technology and Economics Department of Fluid Mechanics University of Rome La Sapienza 2002 Influence of flow characteristics on the

More information

XI / PHYSICS FLUIDS IN MOTION 11/PA

XI / PHYSICS FLUIDS IN MOTION 11/PA Viscosity It is the property of a liquid due to which it flows in the form of layers and each layer opposes the motion of its adjacent layer. Cause of viscosity Consider two neighboring liquid layers A

More information

CFD ANALYSIS OF CONTROLLABLE PITCH PROPELLER USED IN MARINE VEHICLE

CFD ANALYSIS OF CONTROLLABLE PITCH PROPELLER USED IN MARINE VEHICLE CFD ANALYSIS OF CONROLLABLE PICH PROPELLER USED IN MARINE VEHICLE Aditya Kolakoti 1,.V.K.Bhanuprakash 2 & H.N.Das 3 1 M.E in Marine Engineering And Mechanical Handling, Dept of Marine Engineering, Andhra

More information

Natural Convection. Buoyancy force

Natural Convection. Buoyancy force Natural Convection In natural convection, the fluid motion occurs by natural means such as buoyancy. Since the fluid velocity associated with natural convection is relatively low, the heat transfer coefficient

More information

1. Fluids Mechanics and Fluid Properties. 1.1 Objectives of this section. 1.2 Fluids

1. Fluids Mechanics and Fluid Properties. 1.1 Objectives of this section. 1.2 Fluids 1. Fluids Mechanics and Fluid Properties What is fluid mechanics? As its name suggests it is the branch of applied mechanics concerned with the statics and dynamics of fluids - both liquids and gases.

More information

A. Hyll and V. Horák * Department of Mechanical Engineering, Faculty of Military Technology, University of Defence, Brno, Czech Republic

A. Hyll and V. Horák * Department of Mechanical Engineering, Faculty of Military Technology, University of Defence, Brno, Czech Republic AiMT Advances in Military Technology Vol. 8, No. 1, June 2013 Aerodynamic Characteristics of Multi-Element Iced Airfoil CFD Simulation A. Hyll and V. Horák * Department of Mechanical Engineering, Faculty

More information

FLUID FLOW STREAMLINE LAMINAR FLOW TURBULENT FLOW REYNOLDS NUMBER

FLUID FLOW STREAMLINE LAMINAR FLOW TURBULENT FLOW REYNOLDS NUMBER VISUAL PHYSICS School of Physics University of Sydney Australia FLUID FLOW STREAMLINE LAMINAR FLOW TURBULENT FLOW REYNOLDS NUMBER? What type of fluid flow is observed? The above pictures show how the effect

More information

INTRODUCTION TO FLUID MECHANICS

INTRODUCTION TO FLUID MECHANICS INTRODUCTION TO FLUID MECHANICS SIXTH EDITION ROBERT W. FOX Purdue University ALAN T. MCDONALD Purdue University PHILIP J. PRITCHARD Manhattan College JOHN WILEY & SONS, INC. CONTENTS CHAPTER 1 INTRODUCTION

More information

du u U 0 U dy y b 0 b

du u U 0 U dy y b 0 b BASIC CONCEPTS/DEFINITIONS OF FLUID MECHANICS (by Marios M. Fyrillas) 1. Density (πυκνότητα) Symbol: 3 Units of measure: kg / m Equation: m ( m mass, V volume) V. Pressure (πίεση) Alternative definition:

More information

I think that a smaller radius of curvature will produce more lift using the Coanda Effect.

I think that a smaller radius of curvature will produce more lift using the Coanda Effect. The Coanda Conundrum Mackenzie Carter Background My experiment was constructed to test the Coanda effect which occurs when a fluid that is traveling parallel to a nearby surface adheres to that surface.

More information

Lecture 5 Hemodynamics. Description of fluid flow. The equation of continuity

Lecture 5 Hemodynamics. Description of fluid flow. The equation of continuity 1 Lecture 5 Hemodynamics Description of fluid flow Hydrodynamics is the part of physics, which studies the motion of fluids. It is based on the laws of mechanics. Hemodynamics studies the motion of blood

More information

To provide insight into the physics of arrow flight and show how archers adapt their equipment to maximize effectiveness.

To provide insight into the physics of arrow flight and show how archers adapt their equipment to maximize effectiveness. The Science of Archery Godai Katsunaga Purpose To provide insight into the physics of arrow flight and show how archers adapt their equipment to maximize effectiveness. Archery Archery is one of the events

More information

CFD Study on the Diffuser of a Formula 3 Racecar

CFD Study on the Diffuser of a Formula 3 Racecar CFD Study on the Diffuser of a Formula 3 Racecar Kevin M. Peddie, Luis F. Gonzalez School of Aerospace, Mechanical and Mechatronic Engineering University of Sydney ABSTRACT The primary goal of the paper

More information

XFlow CFD results for the 1st AIAA High Lift Prediction Workshop

XFlow CFD results for the 1st AIAA High Lift Prediction Workshop XFlow CFD results for the 1st AIAA High Lift Prediction Workshop David M. Holman, Dr. Monica Mier-Torrecilla, Ruddy Brionnaud Next Limit Technologies, Spain THEME Computational Fluid Dynamics KEYWORDS

More information

The Influence of Aerodynamics on the Design of High-Performance Road Vehicles

The Influence of Aerodynamics on the Design of High-Performance Road Vehicles The Influence of Aerodynamics on the Design of High-Performance Road Vehicles Guido Buresti Department of Aerospace Engineering University of Pisa (Italy) 1 CONTENTS ELEMENTS OF AERODYNAMICS AERODYNAMICS

More information

(1) 2 TEST SETUP. Table 1 Summary of models used for calculating roughness parameters Model Published z 0 / H d/h

(1) 2 TEST SETUP. Table 1 Summary of models used for calculating roughness parameters Model Published z 0 / H d/h Estimation of Surface Roughness using CFD Simulation Daniel Abdi a, Girma T. Bitsuamlak b a Research Assistant, Department of Civil and Environmental Engineering, FIU, Miami, FL, USA, dabdi001@fiu.edu

More information

CFD Modelling and Real-time testing of the Wave Surface Glider (WSG) Robot

CFD Modelling and Real-time testing of the Wave Surface Glider (WSG) Robot 21st International Congress on Modelling and Simulation, Gold Coast, Australia, 29 Nov to 4 Dec 2015 www.mssanz.org.au/modsim2015 CFD Modelling and Real-time testing of the Wave Surface Glider (WSG) Robot

More information

Free Fall: Observing and Analyzing the Free Fall Motion of a Bouncing Ping-Pong Ball and Calculating the Free Fall Acceleration (Teacher s Guide)

Free Fall: Observing and Analyzing the Free Fall Motion of a Bouncing Ping-Pong Ball and Calculating the Free Fall Acceleration (Teacher s Guide) Free Fall: Observing and Analyzing the Free Fall Motion of a Bouncing Ping-Pong Ball and Calculating the Free Fall Acceleration (Teacher s Guide) 2012 WARD S Science v.11/12 OVERVIEW Students will measure

More information

A Note on Rim Width, Tire Sensitivity, and Rim Depth in High Performance Bicycle Wheels.

A Note on Rim Width, Tire Sensitivity, and Rim Depth in High Performance Bicycle Wheels. A Note on Rim Width, Tire Sensitivity, and Rim Depth in High Performance Bicycle Wheels. History: In the late 1980 s aerodynamic bicycle wheels were beginning to evolve past the revolutionary disc wheels

More information

AUTOMOTIVE COMPUTATIONAL FLUID DYNAMICS SIMULATION OF A CAR USING ANSYS

AUTOMOTIVE COMPUTATIONAL FLUID DYNAMICS SIMULATION OF A CAR USING ANSYS International Journal of Mechanical Engineering and Technology (IJMET) Volume 7, Issue 2, March-April 2016, pp. 91 104, Article ID: IJMET_07_02_013 Available online at http://www.iaeme.com/ijmet/issues.asp?jtype=ijmet&vtype=7&itype=2

More information

Holes in a bottle filled with water: which water-jet has the largest range?

Holes in a bottle filled with water: which water-jet has the largest range? Holes in a bottle filled with water: which water-jet has the largest range? Gorazd Planinšič, Christian Ucke and Laurence Viennot. ABSTRACT In some textbooks, a simple experiment is often presented about

More information

Solving Simultaneous Equations and Matrices

Solving Simultaneous Equations and Matrices Solving Simultaneous Equations and Matrices The following represents a systematic investigation for the steps used to solve two simultaneous linear equations in two unknowns. The motivation for considering

More information

CFD Analysis on Airfoil at High Angles of Attack

CFD Analysis on Airfoil at High Angles of Attack CFD Analysis on Airfoil at High Angles of Attack Dr.P.PrabhakaraRao¹ & Sri Sampath.V² Department of Mechanical Engineering,Kakatiya Institute of Technology& Science Warangal-506015 1 chantifft@rediffmail.com,

More information

NACA airfoil geometrical construction

NACA airfoil geometrical construction The NACA airfoil series The early NACA airfoil series, the 4-digit, 5-digit, and modified 4-/5-digit, were generated using analytical equations that describe the camber (curvature) of the mean-line (geometric

More information

Principles of Flight. Chapter 3. Introduction. Structure of the Atmosphere

Principles of Flight. Chapter 3. Introduction. Structure of the Atmosphere Chapter 3 Principles of Flight Introduction This chapter examines the fundamental physical laws governing the forces acting on an aircraft in flight, and what effect these natural laws and forces have

More information

Aerodynamics of Flight

Aerodynamics of Flight Chapter 2 Aerodynamics of Flight Introduction This chapter presents aerodynamic fundamentals and principles as they apply to helicopters. The content relates to flight operations and performance of normal

More information

Chapter 2. Derivation of the Equations of Open Channel Flow. 2.1 General Considerations

Chapter 2. Derivation of the Equations of Open Channel Flow. 2.1 General Considerations Chapter 2. Derivation of the Equations of Open Channel Flow 2.1 General Considerations Of interest is water flowing in a channel with a free surface, which is usually referred to as open channel flow.

More information

University Turbine Systems Research 2012 Fellowship Program Final Report. Prepared for: General Electric Company

University Turbine Systems Research 2012 Fellowship Program Final Report. Prepared for: General Electric Company University Turbine Systems Research 2012 Fellowship Program Final Report Prepared for: General Electric Company Gas Turbine Aerodynamics Marion Building 300 Garlington Rd Greenville, SC 29615, USA Prepared

More information

Design and Structural Analysis of the Ribs and Spars of Swept Back Wing

Design and Structural Analysis of the Ribs and Spars of Swept Back Wing Design and Structural Analysis of the Ribs and Spars of Swept Back Wing Mohamed Hamdan A 1, Nithiyakalyani S 2 1,2 Assistant Professor, Aeronautical Engineering & Srinivasan Engineering College, Perambalur,

More information

4.What is the appropriate dimensionless parameter to use in comparing flow types? YOUR ANSWER: The Reynolds Number, Re.

4.What is the appropriate dimensionless parameter to use in comparing flow types? YOUR ANSWER: The Reynolds Number, Re. CHAPTER 08 1. What is most likely to be the main driving force in pipe flow? A. Gravity B. A pressure gradient C. Vacuum 2.What is a general description of the flow rate in laminar flow? A. Small B. Large

More information

Design Considerations for Water-Bottle Rockets. The next few pages are provided to help in the design of your water-bottle rocket.

Design Considerations for Water-Bottle Rockets. The next few pages are provided to help in the design of your water-bottle rocket. Acceleration= Force OVER Mass Design Considerations for Water-Bottle Rockets The next few pages are provided to help in the design of your water-bottle rocket. Newton s First Law: Objects at rest will

More information

NACA Nomenclature NACA 2421. NACA Airfoils. Definitions: Airfoil Geometry

NACA Nomenclature NACA 2421. NACA Airfoils. Definitions: Airfoil Geometry 0.40 m 0.21 m 0.02 m NACA Airfoils 6-Feb-08 AE 315 Lesson 10: Airfoil nomenclature and properties 1 Definitions: Airfoil Geometry z Mean camber line Chord line x Chord x=0 x=c Leading edge Trailing edge

More information

CFD ANALYSIS OF RAE 2822 SUPERCRITICAL AIRFOIL AT TRANSONIC MACH SPEEDS

CFD ANALYSIS OF RAE 2822 SUPERCRITICAL AIRFOIL AT TRANSONIC MACH SPEEDS CFD ANALYSIS OF RAE 2822 SUPERCRITICAL AIRFOIL AT TRANSONIC MACH SPEEDS K.Harish Kumar 1, CH.Kiran Kumar 2, T.Naveen Kumar 3 1 M.Tech Thermal Engineering, Sanketika Institute of Technology & Management,

More information

NUMERICAL ANALYSIS OF WELLS TURBINE FOR WAVE POWER CONVERSION

NUMERICAL ANALYSIS OF WELLS TURBINE FOR WAVE POWER CONVERSION Engineering Review Vol. 32, Issue 3, 141-146, 2012. 141 NUMERICAL ANALYSIS OF WELLS TURBINE FOR WAVE POWER CONVERSION Z. 1* L. 1 V. 2 M. 1 1 Department of Fluid Mechanics and Computational Engineering,

More information

Aeroelastic Investigation of the Sandia 100m Blade Using Computational Fluid Dynamics

Aeroelastic Investigation of the Sandia 100m Blade Using Computational Fluid Dynamics Aeroelastic Investigation of the Sandia 100m Blade Using Computational Fluid Dynamics David Corson Altair Engineering, Inc. Todd Griffith Sandia National Laboratories Tom Ashwill (Retired) Sandia National

More information

13.021 Marine Hydrodynamics Lecture 24B Lifting Surfaces. Introduction What are the characteristics of a lifting surface?

13.021 Marine Hydrodynamics Lecture 24B Lifting Surfaces. Introduction What are the characteristics of a lifting surface? 13.021 Marine Hydrodynamics Lecture 24B Lifting Surfaces Introduction What are the characteristics of a lifting surface? Lifting surfaces in marine hydrodynamics typically have many applications such as

More information

Multiphase Flow - Appendices

Multiphase Flow - Appendices Discovery Laboratory Multiphase Flow - Appendices 1. Creating a Mesh 1.1. What is a geometry? The geometry used in a CFD simulation defines the problem domain and boundaries; it is the area (2D) or volume

More information

How To Run A Cdef Simulation

How To Run A Cdef Simulation Simple CFD Simulations and Visualisation using OpenFOAM and ParaView Sachiko Arvelius, PhD Purpose of this presentation To show my competence in CFD (Computational Fluid Dynamics) simulation and visualisation

More information

Section 4: The Basics of Satellite Orbits

Section 4: The Basics of Satellite Orbits Section 4: The Basics of Satellite Orbits MOTION IN SPACE VS. MOTION IN THE ATMOSPHERE The motion of objects in the atmosphere differs in three important ways from the motion of objects in space. First,

More information

Distinguished Professor George Washington University. Graw Hill

Distinguished Professor George Washington University. Graw Hill Mechanics of Fluids Fourth Edition Irving H. Shames Distinguished Professor George Washington University Graw Hill Boston Burr Ridge, IL Dubuque, IA Madison, Wl New York San Francisco St. Louis Bangkok

More information

Contents. Microfluidics - Jens Ducrée Physics: Fluid Dynamics 1

Contents. Microfluidics - Jens Ducrée Physics: Fluid Dynamics 1 Contents 1. Introduction 2. Fluids 3. Physics of Microfluidic Systems 4. Microfabrication Technologies 5. Flow Control 6. Micropumps 7. Sensors 8. Ink-Jet Technology 9. Liquid Handling 10.Microarrays 11.Microreactors

More information

Simulation at Aeronautics Test Facilities A University Perspective Helen L. Reed, Ph.D., P.E. ASEB meeting, Irvine CA 15 October 2014 1500-1640

Simulation at Aeronautics Test Facilities A University Perspective Helen L. Reed, Ph.D., P.E. ASEB meeting, Irvine CA 15 October 2014 1500-1640 Simulation at Aeronautics Test A University Perspective Helen L. Reed, Ph.D., P.E. ASEB meeting, Irvine CA 15 October 2014 1500-1640 Questions How has the ability to do increasingly accurate modeling and

More information

UCCS PES/ENSC 2500: Renewable Energy Spring 2014 Test 3 name:

UCCS PES/ENSC 2500: Renewable Energy Spring 2014 Test 3 name: UCCS PES/ENSC 2500: Renewable Energy Spring 2014 Test 3 name: 1. When a wind turbine is positioned between radio, television or microwave transmitter and receiver it can sometime reflect some of the in

More information

O.F.Wind Wind Site Assessment Simulation in complex terrain based on OpenFOAM. Darmstadt, 27.06.2012

O.F.Wind Wind Site Assessment Simulation in complex terrain based on OpenFOAM. Darmstadt, 27.06.2012 O.F.Wind Wind Site Assessment Simulation in complex terrain based on OpenFOAM Darmstadt, 27.06.2012 Michael Ehlen IB Fischer CFD+engineering GmbH Lipowskystr. 12 81373 München Tel. 089/74118743 Fax 089/74118749

More information

THE EFFECT OF BLADE ANGLE AND SIZE ON WIND TURBINE PERFORMANCE

THE EFFECT OF BLADE ANGLE AND SIZE ON WIND TURBINE PERFORMANCE THE EFFECT OF BLADE ANGLE AND SIZE ON WIND TURBINE PERFORMANCE Anish Bhattacharya, 8 th Grade, Unity Point School District 140 PURPOSE We have experienced a major fall in the economy in the recent past.

More information

CFD analysis for road vehicles - case study

CFD analysis for road vehicles - case study CFD analysis for road vehicles - case study Dan BARBUT*,1, Eugen Mihai NEGRUS 1 *Corresponding author *,1 POLITEHNICA University of Bucharest, Faculty of Transport, Splaiul Independentei 313, 060042, Bucharest,

More information

How do sails work? Article by Paul Bogataj

How do sails work? Article by Paul Bogataj How do sails work? Article by Paul Bogataj Sails are wings that use the wind to generate a force to move a boat. The following explanation of how this occurs can help understand how to maximize the performance

More information

ENHANCEMENT OF AERODYNAMIC PERFORMANCE OF A FORMULA-1 RACE CAR USING ADD-ON DEVICES B. N. Devaiah 1, S. Umesh 2

ENHANCEMENT OF AERODYNAMIC PERFORMANCE OF A FORMULA-1 RACE CAR USING ADD-ON DEVICES B. N. Devaiah 1, S. Umesh 2 ENHANCEMENT OF AERODYNAMIC PERFORMANCE OF A FORMULA-1 RACE CAR USING ADD-ON DEVICES B. N. Devaiah 1, S. Umesh 2 1- M. Sc. [Engg.] Student, 2- Asst. Professor Automotive and Aeronautical Engineering Department,

More information

THE MODIFICATION OF WIND-TUNNEL RESULTS BY THE WIND-TUNNEL DIMENSIONS

THE MODIFICATION OF WIND-TUNNEL RESULTS BY THE WIND-TUNNEL DIMENSIONS THE MODIFICATION OF WIND-TUNNEL RESULTS BY THE WIND-TUNNEL DIMENSIONS 13\' MAX M. MONK, Ph.D., Dr.Eng. Technical Assistant, National Advisory Committee for Aeronautics RIlPRINTED FROM THII JOURNAL OF THE

More information

Dimensional Analysis

Dimensional Analysis Dimensional Analysis An Important Example from Fluid Mechanics: Viscous Shear Forces V d t / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / Ƭ = F/A = μ V/d More generally, the viscous

More information

THE CFD SIMULATION OF THE FLOW AROUND THE AIRCRAFT USING OPENFOAM AND ANSA

THE CFD SIMULATION OF THE FLOW AROUND THE AIRCRAFT USING OPENFOAM AND ANSA THE CFD SIMULATION OF THE FLOW AROUND THE AIRCRAFT USING OPENFOAM AND ANSA Adam Kosík Evektor s.r.o., Czech Republic KEYWORDS CFD simulation, mesh generation, OpenFOAM, ANSA ABSTRACT In this paper we describe

More information

Turn off all electronic devices

Turn off all electronic devices Balloons 1 Balloons 2 Observations about Balloons Balloons Balloons are held taut by the gases inside Some balloon float in air while others don t Hot-air balloons don t have to be sealed Helium balloons

More information

Dimensional analysis is a method for reducing the number and complexity of experimental variables that affect a given physical phenomena.

Dimensional analysis is a method for reducing the number and complexity of experimental variables that affect a given physical phenomena. Dimensional Analysis and Similarity Dimensional analysis is very useful for planning, presentation, and interpretation of experimental data. As discussed previously, most practical fluid mechanics problems

More information

Resistance in the Mechanical System. Overview

Resistance in the Mechanical System. Overview Overview 1. What is resistance? A force that opposes motion 2. In the mechanical system, what are two common forms of resistance? friction and drag 3. What is friction? resistance that is produced when

More information

A Method for Generating Electricity by Fast Moving Vehicles

A Method for Generating Electricity by Fast Moving Vehicles A Method for Generating Electricity by Fast Moving Vehicles S.Bharathi 1, G.Balaji 2, and M. Manoj Kumar 2 1 Angel College of Engineering & Technology/ECE, Tirupur, India Email: bharathiseven@gmail.com

More information

AP1 Oscillations. 1. Which of the following statements about a spring-block oscillator in simple harmonic motion about its equilibrium point is false?

AP1 Oscillations. 1. Which of the following statements about a spring-block oscillator in simple harmonic motion about its equilibrium point is false? 1. Which of the following statements about a spring-block oscillator in simple harmonic motion about its equilibrium point is false? (A) The displacement is directly related to the acceleration. (B) The

More information

FAN PROTECTION AGAINST STALLING PHENOMENON

FAN PROTECTION AGAINST STALLING PHENOMENON FAN PROTECTION AGAINST STALLING PHENOMENON Roberto Arias Álvarez 1 Javier Fernández López 2 2 1 ZITRON Technical Director roberto@zitron.com ZITRON Technical Pre Sales Management jfernandez@zitron.com

More information

Application of CFD in connection with ship design

Application of CFD in connection with ship design DANSIS meeting Lyngby, 13 May 2009 Application of CFD in connection with ship design www.force.dk Background Method Examples Summary Claus Daniel Simonsen FORCE Technology Background When a ship, which

More information

The Viscosity of Fluids

The Viscosity of Fluids Experiment #11 The Viscosity of Fluids References: 1. Your first year physics textbook. 2. D. Tabor, Gases, Liquids and Solids: and Other States of Matter (Cambridge Press, 1991). 3. J.R. Van Wazer et

More information

Relevance of Modern Optimization Methods in Turbo Machinery Applications

Relevance of Modern Optimization Methods in Turbo Machinery Applications Relevance of Modern Optimization Methods in Turbo Machinery Applications - From Analytical Models via Three Dimensional Multidisciplinary Approaches to the Optimization of a Wind Turbine - Prof. Dr. Ing.

More information

Basic Principles in Microfluidics

Basic Principles in Microfluidics Basic Principles in Microfluidics 1 Newton s Second Law for Fluidics Newton s 2 nd Law (F= ma) : Time rate of change of momentum of a system equal to net force acting on system!f = dp dt Sum of forces

More information

Head Loss in Pipe Flow ME 123: Mechanical Engineering Laboratory II: Fluids

Head Loss in Pipe Flow ME 123: Mechanical Engineering Laboratory II: Fluids Head Loss in Pipe Flow ME 123: Mechanical Engineering Laboratory II: Fluids Dr. J. M. Meyers Dr. D. G. Fletcher Dr. Y. Dubief 1. Introduction Last lab you investigated flow loss in a pipe due to the roughness

More information

Chapter 5 Using Newton s Laws: Friction, Circular Motion, Drag Forces. Copyright 2009 Pearson Education, Inc.

Chapter 5 Using Newton s Laws: Friction, Circular Motion, Drag Forces. Copyright 2009 Pearson Education, Inc. Chapter 5 Using Newton s Laws: Friction, Circular Motion, Drag Forces Units of Chapter 5 Applications of Newton s Laws Involving Friction Uniform Circular Motion Kinematics Dynamics of Uniform Circular

More information

Physics 2A, Sec B00: Mechanics -- Winter 2011 Instructor: B. Grinstein Final Exam

Physics 2A, Sec B00: Mechanics -- Winter 2011 Instructor: B. Grinstein Final Exam Physics 2A, Sec B00: Mechanics -- Winter 2011 Instructor: B. Grinstein Final Exam INSTRUCTIONS: Use a pencil #2 to fill your scantron. Write your code number and bubble it in under "EXAM NUMBER;" an entry

More information

Express Introductory Training in ANSYS Fluent Lecture 1 Introduction to the CFD Methodology

Express Introductory Training in ANSYS Fluent Lecture 1 Introduction to the CFD Methodology Express Introductory Training in ANSYS Fluent Lecture 1 Introduction to the CFD Methodology Dimitrios Sofialidis Technical Manager, SimTec Ltd. Mechanical Engineer, PhD PRACE Autumn School 2013 - Industry

More information

The influence of mesh characteristics on OpenFOAM simulations of the DrivAer model

The influence of mesh characteristics on OpenFOAM simulations of the DrivAer model The influence of mesh characteristics on OpenFOAM simulations of the DrivAer model Vangelis Skaperdas, Aristotelis Iordanidis, Grigoris Fotiadis BETA CAE Systems S.A. 2 nd Northern Germany OpenFOAM User

More information

F1 in Schools - 2014 World Finals Technical Regulations. 2014 WORLD FINALS Technical Regulations

F1 in Schools - 2014 World Finals Technical Regulations. 2014 WORLD FINALS Technical Regulations 2014 WORLD FINALS Technical Regulations Refer also to the 2014 World Finals Competition Regulations. For World Finals use only. 2013 - F1 in Schools Ltd. Page 1 of 23 13 August 2014 Front Cover A1 Racing

More information

1. Units of a magnetic field might be: A. C m/s B. C s/m C. C/kg D. kg/c s E. N/C m ans: D

1. Units of a magnetic field might be: A. C m/s B. C s/m C. C/kg D. kg/c s E. N/C m ans: D Chapter 28: MAGNETIC FIELDS 1 Units of a magnetic field might be: A C m/s B C s/m C C/kg D kg/c s E N/C m 2 In the formula F = q v B: A F must be perpendicular to v but not necessarily to B B F must be

More information

Finding Drag Coefficient using Solidworks Flow Simulation

Finding Drag Coefficient using Solidworks Flow Simulation Finding Drag Coefficient using Solidworks Flow Simulation Using solidworks to find the drag coefficient of shapes is a very useful way to cut down on the design time of a project, as it can remove tests.

More information

PASSIVE CONTROL OF SHOCK WAVE APPLIED TO HELICOPTER ROTOR HIGH-SPEED IMPULSIVE NOISE REDUCTION

PASSIVE CONTROL OF SHOCK WAVE APPLIED TO HELICOPTER ROTOR HIGH-SPEED IMPULSIVE NOISE REDUCTION TASK QUARTERLY 14 No 3, 297 305 PASSIVE CONTROL OF SHOCK WAVE APPLIED TO HELICOPTER ROTOR HIGH-SPEED IMPULSIVE NOISE REDUCTION PIOTR DOERFFER AND OSKAR SZULC Institute of Fluid-Flow Machinery, Polish Academy

More information

VISUAL PHYSICS School of Physics University of Sydney Australia. Why do cars need different oils in hot and cold countries?

VISUAL PHYSICS School of Physics University of Sydney Australia. Why do cars need different oils in hot and cold countries? VISUAL PHYSICS School of Physics University of Sydney Australia FLUID FLOW VISCOSITY POISEUILLE'S LAW? Why do cars need different oils in hot and cold countries? Why does the engine runs more freely as

More information

Chapter 6 Lateral static stability and control - 3 Lecture 21 Topics

Chapter 6 Lateral static stability and control - 3 Lecture 21 Topics Chapter 6 Lateral static stability and control - 3 Lecture 21 Topics 6.11 General discussions on control surface 6.11.1 Aerodynamic balancing 6.11.2 Set back hinge or over hang balance 6.11.3 Horn balanace

More information

Forces on the Rocket. Rocket Dynamics. Equation of Motion: F = Ma

Forces on the Rocket. Rocket Dynamics. Equation of Motion: F = Ma Rocket Dynamics orces on the Rockets - Drag Rocket Stability Rocket Equation Specific Impulse Rocket otors Thrust orces on the Rocket Equation of otion: = a orces at through the Center of ass Center of

More information

Adaptation of General Purpose CFD Code for Fusion MHD Applications*

Adaptation of General Purpose CFD Code for Fusion MHD Applications* Adaptation of General Purpose CFD Code for Fusion MHD Applications* Andrei Khodak Princeton Plasma Physics Laboratory P.O. Box 451 Princeton, NJ, 08540 USA akhodak@pppl.gov Abstract Analysis of many fusion

More information

Use of OpenFoam in a CFD analysis of a finger type slug catcher. Dynaflow Conference 2011 January 13 2011, Rotterdam, the Netherlands

Use of OpenFoam in a CFD analysis of a finger type slug catcher. Dynaflow Conference 2011 January 13 2011, Rotterdam, the Netherlands Use of OpenFoam in a CFD analysis of a finger type slug catcher Dynaflow Conference 2011 January 13 2011, Rotterdam, the Netherlands Agenda Project background Analytical analysis of two-phase flow regimes

More information

Technical Regulations 2015-2016

Technical Regulations 2015-2016 F1 in Schools - 2014 World Finals Technical Regulations Technical Regulations 2015-2016 2013 - F1 in Schools Ltd. Page 1 of 27 3 September 2015 CONTENTS PREFACE SUMMARY OF MAIN REVISIONS FROM 2013 REGULATIONS...

More information

A CFD Study of Wind Turbine Aerodynamics

A CFD Study of Wind Turbine Aerodynamics A CFD Study of Wind Turbine Aerodynamics Chris Kaminsky *, Austin Filush *, Paul Kasprzak * and Wael Mokhtar ** Department of Mechanical Engineering Grand Valley State University Grand Rapids, Michigan

More information

APPENDIX 3-B Airplane Upset Recovery Briefing. Briefing. Figure 3-B.1

APPENDIX 3-B Airplane Upset Recovery Briefing. Briefing. Figure 3-B.1 APPENDIX 3-B Airplane Upset Recovery Briefing Industry Solutions for Large Swept-Wing Turbofan Airplanes Typically Seating More Than 100 Passengers Briefing Figure 3-B.1 Revision 1_August 2004 Airplane

More information

What is a Mouse-Trap

What is a Mouse-Trap What is a Mouse-Trap Car and How does it Work? A mouse-trap car is a vehicle that is powered by the energy that can be stored in a wound up mouse-trap spring. The most basic design is as follows: a string

More information

NUMERICAL AND EXPERIMENTAL ANALYSIS OF THE WIND FORCES ACTING ON LNG CARRIER

NUMERICAL AND EXPERIMENTAL ANALYSIS OF THE WIND FORCES ACTING ON LNG CARRIER V European Conference on Computational Fluid Dynamics ECCOMAS CFD 1 J. C. F. Pereira and A. Sequeira (Eds) Lisbon, Portugal, 14 17 June 1 NUMERICAL AND EXPERIMENTAL ANALYSIS OF THE WIND FORCES ACTING ON

More information

Fluids and Solids: Fundamentals

Fluids and Solids: Fundamentals Fluids and Solids: Fundamentals We normally recognize three states of matter: solid; liquid and gas. However, liquid and gas are both fluids: in contrast to solids they lack the ability to resist deformation.

More information

The Influence of Aerodynamics on the Design of High-Performance Road Vehicles

The Influence of Aerodynamics on the Design of High-Performance Road Vehicles The Influence of Aerodynamics on the Design of High-Performance Road Vehicles Guido Buresti Department of Aerospace Engineering University of Pisa (Italy) 1 CONTENTS ELEMENTS OF AERODYNAMICS AERODYNAMICS

More information

Copyright 2011 Casa Software Ltd. www.casaxps.com. Centre of Mass

Copyright 2011 Casa Software Ltd. www.casaxps.com. Centre of Mass Centre of Mass A central theme in mathematical modelling is that of reducing complex problems to simpler, and hopefully, equivalent problems for which mathematical analysis is possible. The concept of

More information

Experimental investigation of golf driver club head drag reduction through the use of aerodynamic features on the driver crown

Experimental investigation of golf driver club head drag reduction through the use of aerodynamic features on the driver crown Available online at www.sciencedirect.com Procedia Engineering 00 (2013) 000 000 www.elsevier.com/locate/procedia The 2014 conference of the International Sports Engineering Association Experimental investigation

More information

Aerodynamic Department Institute of Aviation. Adam Dziubiński CFD group FLUENT

Aerodynamic Department Institute of Aviation. Adam Dziubiński CFD group FLUENT Adam Dziubiński CFD group IoA FLUENT Content Fluent CFD software 1. Short description of main features of Fluent 2. Examples of usage in CESAR Analysis of flow around an airfoil with a flap: VZLU + ILL4xx

More information

Eco Pelmet Modelling and Assessment. CFD Based Study. Report Number 610.14351-R1D1. 13 January 2015

Eco Pelmet Modelling and Assessment. CFD Based Study. Report Number 610.14351-R1D1. 13 January 2015 EcoPelmet Pty Ltd c/- Geoff Hesford Engineering 45 Market Street FREMANTLE WA 6160 Version: Page 2 PREPARED BY: ABN 29 001 584 612 2 Lincoln Street Lane Cove NSW 2066 Australia (PO Box 176 Lane Cove NSW

More information

F1 in Schools - 2015 World Finals Technical Regulations

F1 in Schools - 2015 World Finals Technical Regulations 2013 - F1 in Schools Ltd. Page 1 of 24 25 March 2015 Front Cover Colossus F1 2014 World Champions F1 Car, Robert May's School, Hampshire, England Amendments made on [Date] are indicated thus (using red

More information

NACA 2415- FINDING LIFT COEFFICIENT USING CFD, THEORETICAL AND JAVAFOIL

NACA 2415- FINDING LIFT COEFFICIENT USING CFD, THEORETICAL AND JAVAFOIL NACA 2415- FINDING LIFT COEFFICIENT USING CFD, THEORETICAL AND JAVAFOIL Sarfaraj Nawaz Shaha 1, M. Sadiq A. Pachapuri 2 1 P.G. Student, MTech Design Engineering, KLE Dr. M S Sheshgiri College of Engineering

More information

Turbulence Modeling in CFD Simulation of Intake Manifold for a 4 Cylinder Engine

Turbulence Modeling in CFD Simulation of Intake Manifold for a 4 Cylinder Engine HEFAT2012 9 th International Conference on Heat Transfer, Fluid Mechanics and Thermodynamics 16 18 July 2012 Malta Turbulence Modeling in CFD Simulation of Intake Manifold for a 4 Cylinder Engine Dr MK

More information

AERODYNAMIC ANALYSIS OF BLADE 1.5 KW OF DUAL ROTOR HORIZONTAL AXIS WIND TURBINE

AERODYNAMIC ANALYSIS OF BLADE 1.5 KW OF DUAL ROTOR HORIZONTAL AXIS WIND TURBINE AERODYNAMIC ANALYSIS OF BLADE 1.5 KW OF DUAL ROTOR HORIZONTAL AXIS WIND TURBINE HITENDRA KURMI Research scholar, School of Energy and Environmental Managment,UTD, RGPV Bhopal,MP,INDIA htr.ptl@gmail.com

More information

Density. Density is how concentrated or compact matter is.

Density. Density is how concentrated or compact matter is. Density Density is how concentrated or compact matter is. Packing snow into snowballs increases its density. You are squeezing large amounts of matter into small volumes of space. Equation for Density

More information

HEAT TRANSFER ANALYSIS IN A 3D SQUARE CHANNEL LAMINAR FLOW WITH USING BAFFLES 1 Vikram Bishnoi

HEAT TRANSFER ANALYSIS IN A 3D SQUARE CHANNEL LAMINAR FLOW WITH USING BAFFLES 1 Vikram Bishnoi HEAT TRANSFER ANALYSIS IN A 3D SQUARE CHANNEL LAMINAR FLOW WITH USING BAFFLES 1 Vikram Bishnoi 2 Rajesh Dudi 1 Scholar and 2 Assistant Professor,Department of Mechanical Engineering, OITM, Hisar (Haryana)

More information

Rowing Blade Design using CFD

Rowing Blade Design using CFD Rowing Blade Design using CFD Master of Science Thesis For obtaining the degree of Master of Science in Aerospace Engineering at Delft University of Technology M. Kamphorst B.Sc. June 30, 2009 Faculty

More information