2 EC 160 EC 160 CO 2 INCUBATOR Chamber Volume : 160 liters Temperature range: Ambient Temperature: + 7 C to 50 C Temperature variation / fluctuation: ± 0,3 C at 37 C / ± 0,1 C Programmable temperature alarm range: ± 0,5 C to 5 C Air jacketed heating system RaPIDcell fast temperature recovery without overshoot CO 2 Range: 0 to 20 % CO 2 CO 2 Variation / Fluctuation: ± 0.3 % / ± 0.1% Programmable CO 2 alarm range: ± 0.5 % to 5.0% Infra-Red CO 2 level control permitting frequent access LifeCell control software to optimize parameters Large, bright LCD display with text messages and help Simultaneous display of set and actual values Seamless stainless steel chamber with rounded corners Clean chamber without any sensor inside NüveDis 90 C wet disinfection system NüveTrack monitoring and recall of last 72 hr. parameter values and alarms Auto Zero for permanent accurate control 0.22 μm sterile filtration of CO 2, sampled gases and Auto-Zero reference air Typical 95 % RH to protect cultures against dehydration Audible and visual (text) alarms, remote alarm relay Remote alarm outlet Built-in 2nd stage gas regulator Three shelves Humidity tray
3 Highly visible, large LED display Temperature, data tracking and storage on PC via optional RS 232 port and NüveFREEZE software Password protected control system Door handle with key lock Key operated mains power switch to protect your samples Audible and visual alarm system Alarm system is fed by a permanently recharged battery Display of actual temperature even at power failure Standard remote and central alarm ports Optional battery-operated 7- day chart recorder Optional AlerText SMS alarm system for ultimate security Optional NüveWarn remote alarm system Optional CO2 back-up system extends protection in case of failure (DF only) Up to 32,000 tubes storage capacity with 455 liters chamber volume DF 490: -86 C FR 490 : -41 C DirectFREEZE : Faster and homogenous freezing through the coils located inside the shelves. Four independent compartments with insulated doors for decreasing air entry Minimized air exchange on opening reduces ice build-up and protects samples Compartment dimensions match commonly used cryoboxes Washable air filter for simple maintenance and top performance Perfect airtightness with soft gasket Heated contact surface of gasket to virtually eliminate icing-up Chamber made of stainless steel for long life and shelves made of aluminum for faster heat transfer Epoxy-polyester powder coated stainless steel outer body Foamed-in-place high density polyurethane insulation Easy to use and safe operation using a microprocessor control system DF/FR DF 490 ULTRALOW TEMPERATURE & FR 490 LOW TEMPERATURE DEEP FREEZERS
4 EN Series EN 025/055/120 INCUBATORS Three different sizes: 25, 55 and 120 liters. Temperature range: Ambient Temperature +5 C / 80 C. Excellent incubation conditions for the applications in biology and microbiology laboratories such as medical and veterinary fields; research and quality control examinations in pharmaceutical, food and cosmetics industries and biotechnology. Programmable PID microprocessor control system. User friendly control panel located on the door, including digital displays for temperature and time. Stainless steel interior for easy cleaning and decontamination. Air jacketed heating system and triple insulation for highly precise and constant temperatures. Very homogeneous temperature distribution by natural air convection: Minimum turbulance and no cross contamination. Frameless inner glass door for the observation of samples without any temperature drop. Safety thermostat as standard. Optional NüveTherm data control software and RS 232 kit. EN EN 300/400/500 INCUBATORS Three different sizes: 22, 44 and 120 liters. Temperature range: Ambient Temperature +5 C / 80 C. Excellent incubation conditions for the applications in all biology and microbiology laboratories such as medical and veterinary fields; research and quality control examinations in pharmaceutical, food and cosmetics industries and in biotechnology. Programmable PID microprocessor control system. User friendly control panel including digital displays for temperature and time. Delayed start timer. Anodic-oxidated aluminum chamber for standard models; stainless steel chamber for "P" models. Very homogeneous temperature distribution obtained by natural air convection for standard models and by forced air ventilation for "P" models. Frameless inner glass door for the observation of samples without any temperature drop. Safety thermostat as standard. ES ES 120/252 COOLED INCUBATORS Two different sizes: 120 and 252 liters. Temperature range: -10 C / 60 C. Ideal design for freezing, incubation, drying, different types of tests and long storage in the fields of biology, zoology, botany and the quality control and R&D laboratories in industry such as pharmaceutical, food and cosmetic. Programmable microprocessor control system. Nine program memories with nine steps. Easy to use control panel including digital displays for temperature, time, program no and step no. Stainless steel chamber. High density injected polyurethane insulation. Powerful air circulation system for excellent temperature uniformity and stability even at low temperatures. Automatic defrost system. Large window on the door consisting of triple glass for perfect insulation. Interior lighting with on/off control. Optional NüveTherm data control software and RS 232 kit.
5 FN 032/055/120 DRY HEAT STERILIZERS / OVENS Three different sizes: 32, 55 and 120 liters. Temperature range: Ambient Temperature +5 C / 250 C. Designed for sterilization, drying and heating purposes. Programmable PID microprocessor control system. User friendly control panel including digital displays for temperature and time. Delayed start timer. Stainless steel interior for easy cleaning and high resistance to most of the chemicals. Excellent uniformity and stability of temperature by triple insulation and air jacketed heating system. Natural air convection for homogeneous temperature distribution. Very low temperature loss by means of the door pressing firmly and tightly on the chamber gasket. Outlet port for vapour exhaustion. Safety thermostat as standard. Three different sizes: 22, 44 and 120 liters. Temperature range: Ambient Temperature +5 C / 250 C. Designed for sterilization, drying and heating purposes. Programmable PID microprocessor control system. Easy to use control panel including digital displays for temperature and time. Delayed start timer. Excellent uniformity and stability of temperature by high grade of insulation and microprocessor control system. Anodic-oxidated aluminum chamber for standard models; stainless steel chamber for "P" models. Very homogeneous temperature distribution obtained by natural air convection for standard models and by forced air ventilation for "P" models. Low temperature loss by means of the door pressing firmly and tightly against the chamber gasket. Outlet port for vapour exhaustion. Safety thermostat as standard. FN FN 300/400/500 DRY HEAT STERILIZERS / OVENS EV 018 VACUUM OVEN Useful volume: 15 liters. Temperature range: 70 C / 200 C. Ideal design for gentle drying of heat labile samples and experiments under inert gasses. Programmable PID microprocessor control system. Easy to use control panel including digital displays for temperature and time. Stainless steel chamber with high resistance to corrosion, most of the chemical vapours and contamination. One piece gasket made of silicon, simply fitted directly on the oven body. Vacuum gauge on the control panel. Two spherical valves for vacuum connection and adding dry air or inert gasses. Heat-treated glass window on the door. Safety thermostat as standard. Optional NüveTherm data control software and RS 232 kit KD Three different sizes: 193, 373 and 757 liters. Temperature range: 70 C / 250 C. High volume for drying and heating purposes. Programmable PID microprocessor control system. Easy to use control panel including digital display for temperature and time. Delayed start timer. Excellent uniformity and stability of temperature by high grade of insulation and microprocessor control system. Stainless steel chamber. Very homogeneous temperature distribution obtained by forced air ventilation. Extraction fan. Low temperature loss by means of the door pressing firmly and tightly against the chamber gasket. Outlet port for vapour exhaustion. Safety thermostat as standard. 018 EV KD 200/400/700 OVENS
6 NF 048 MICROLITRE AND HAEMATOCRIT CENTRIFUGE NF Angle Rotor Haematocrit Rotor Maximum Capacity : 24x1.5/2 ml 24xcapillary tubes Maximum Speed : 14,000 rpm 12,000 rpm Maximum RCF : 18,188xg 14,811xg Programmable microprocessor control system. Digital displays for time and speed / RCF (xg) minutes timer with hold position. Epoxy-polyester powder coated steel chamber. Pulse key. Quiet, direct drive, brushless induction motor. Motor over heating protection. Ventilation system for minimum temperature increase in the chamber. Lid lock. Choice of 24x1.5/2 ml Angle Rotor and 24x capillarytube Haematocrit Rotor. Adaptors for 500/800 μl, 200 μl PCR, 250/400/700 μl. NF 200 BENCH TOP CENTRIFUGE Maximum Capacity : 12x15 ml Maximum Speed : rpm Maximum RCF : 2.822xg Programmable microprocessor control system. Digital displays for time and speed / RCF (xg) minutes timer with hold position. Epoxy-polyester powder coated steel chamber. Pulse key. Quiet, direct drive, brushless induction motor. Motor over heating protection. Ventilation system for minimum temperature increase in the chamber. Lid lock. Delivered with 12x15 ml Angle rotor made of polypropylene. Adaptors for 1,5/2 ml, 5 ml and 7 ml tubes. NF 400-NF 400R MEDIUM CAPACITY BENCH TOP CENTRIFUGES NF 800 NF 800R MULTI PURPOSE BENCH TOP CENTRIFUGES NF Maximum Capacity: Maximum Speed : Maximum RCF: Swing-out Rotors 4x200 ml 2x3M.Plate rpm rpm 3.045xg 2.349xg 6x50 ml rpm 9.418xg Angle Rotors 30x15 ml 24x1.5/2 ml rpm rpm 3.007xg xg Angle Rotor Swing-out Rotors Maximum Capacity : 16x15ml 4x100ml 2xM.Plate Maximum Speed : 4,100 rpm 4,100 rpm rpm Maximum RCF : 2.142xg 2.819xg 2.011xg Programmable microprocessor control system. Digital display for time and speed / RCF (xg). Digital display for temperature for NF 400R. Programmable relative centrifugal force (RCF). Electronic imbalance detection system. Stainless steel chamber minutes timer with hold position. 5 acceleration / 5 braking rates. Lid lock. Powerful, quiet, and maintenance - free induction motor. Minimum temperature increase in the chamber by means of ventilation system for NF 400. Temperature control between -9 C / +40 C for NF 400R. Motor over heating protection. Wide range of accessories to accommodate most manufacturers tubes and microtitre plate. Totally CFC free refrigerant fluid and insulation material for NF 400R. NF 1200 NF 1200R MULTI PURPOSE BENCH TOP CENTRIFUGES Maximum Capacity: Maximum Speed : Maximum RCF: Programmable microprocessor control system. Programmable parameters: Program no., speed / RCF, time, acceleration and breaking rates and temperature for NF 800R and NF 1200R. Four digital displays for programmable parameters minutes with hold position. Ten program memories. 10 acceleration / 10 braking rates Stainless steel chamber. Wide range of accessories to accommodate most manufacturers tubes and microtitre plate. Powerful, quite, maintenance-free induction motor. Minimum temperature increase in the chamber by means of ventilation system for NF 800 and NF Temperature control between -9 C / +40 C for NF 800R and NF 1200R. Totally CFC free refrigerant fluid and insulation material for NF 800R and NF 1200R. Swing-out Rotors 4x280 ml 2x3M.Plate rpm rpm 3.082xg 2.349xg 6x100 ml rpm 8.965xg Angle Rotors 10x10 ml 24x2 ml 30x1.5/2 ml rpm rpm rpm xg xg xg
7 BM/BS WATERBATHS BM Different tank volumes and temperature ranges: BM 302 : 14 liters, Ambient Temperature +5 C / 80 C BM 402 : 30 liters, Ambient Temperature +5 C / 80 C BS 302 : 14 liters, 0 C / 80 C BS 402 : 30 liters, 0 C / 80 C ST 30 SHAKING WATERBATH Tank volume: 30 liters Temperature range: Ambient temperature +5 C / 99.9 C Shaking speed between rpm Programmable microprocessor control system for shaking speed, temperature and temperature LED display for shaking speed, temperature and time Excellent temperature control of liquid for uniform and stable temperatures Seamless and stainless steel tank Heater replaced outside of the tank Triple insulation for homogeneous and stable temperature User friendly control panel Possibility to use different type of tubes, flaks or erlenmeyers with the wide range of accessories 402 ST Excellent temperature control of liquid for uniform and stable temperatures. Seamless stainless steel tank. Powerful internal circulation pump for homogeneous temperatures. Programmable microprocessor control system. Easy to use control panel including digital displays for temperature and time. Optional external circulation system for BM and BS series. Various type of tube racks and shelves for flasks. Optional NüveTherm data control software and RS 232 kit NB 5/9/20 UNSTIRRED WATERBATHS NB Three different useful volumes : 4, 7 and 15 liters. Temperature range: Ambient temperature + 5 C / 99.9 C Designed for many general and special applications in microbiology, research and industrial laboratories. Excellent temperature control of liquid by programmable PID microprocessor control system. Highly visible dual display for temperature and time. Delayed start timer. Seamless stainless steel tank for easy cleaning. Excellent temperature uniformity and stability by triple insulation. Footprint almost equal to the working area to save bench space.
8 ND ND 4 / 8 / 12 WATER DISTILLERS Capacity: ND 4: 4 lt/hr, ND 8: 8 lt/hr, ND 12: 12 lt/hr Distilled water storage tank capacity: ND 4: 8 liters, ND 8: 16 liters, ND 12: 24 liters New design with distilled water storage tank Fully automatic system with microprocessor control system Stainless steel boiler and condenser Stainless steel heaters Energy saving design by the distillation of heated cooling water Protected heaters against running dry Warning leds for: High water level, insufficient water, heater failure, half full storage tank, full storage tank Siliphos cartridge filter to decrease calcification on the heaters Suitable for bench and wall mounting NS 103 NS 103 ECONOMICAL WATER DISTILLER PS 54 PS 54 PLATELET AGITATOR Capacity: 54 pcs platelet bags Number of shelves: 9 pcs. Shaking speed: 60 stroke/min Specially designed for platelet bags Low noise operation Body and shelves made of stainless steel Maximum homogeneity with mesh type shelves for air circulation Easy access to platelet bags on pull-out shelves Ergonomic shelf design Information shown on the label holder for each shelf Audible alarm if motion is not detected Distilled water capacity: 3.5 lt / hr. Stainless steel heater. All surfaces in contact with water and steam made of stainless material. Manometer for inlet water pressure. Protection against empty boiling tank and water interruption. High efficiency even at low inlet water pressure. Wall mounted type, saving space in the laboratories. Easy and simple operation.
9 KN Capacity: KN 72 : 202 liters, 72 blood bags, KN 120 : 320 liters, 120 blood bags, KN 294 : 630 liters, 294 blood bags, KN 504 : 1090 liters, 504 blood bags. Advanced technology to store blood and blood components. Stainless steel chamber. High density injected polyurethane insulation. Door window with triple glass for perfect insulation. Magnetic gasket on four sides of the door and door key lock. Chamber illumination with on/off switch control. Easily drawn stainless steel drawers with plexiglass cover on the front. Separators inside the drawers to hold the blood bags in an angled position for easy label reading. Powerful air circulation system to maintain temperature uniformity and stability and for quick recovery time. Fully automatic defrost system to maintain cooling coil efficiency. Mains power witch key with lock. Microprocessor control system to simplify the operation and guarantee the safety of the stored component. Temperature range: 0 C / +10 C. Large digital display with a resolution of 0.1 C. Alarm system for high and low temperature, power failure, temperature sensor failure, and open door. Re-chargable battery to feed alarm system. Remote and central alarm outlets as standard. Optional NüveBank temperature data tracking and storage software and RS 232 port. Temperature measurement from a liquid which has similar thermal specifications with blood. Battery operated 7-day chart recorder with high resolution. Optional AlerText SMS alarm system for ultimate security Optional NüveWarn remote alarm system KN BLOOD BANK REFRIGERATORS PN 150/300 PLATELET INCUBATORS PN PN 150 : Chamber Volume : 187 liters Includes 1 pc PS 54 Platelet Agitator PN 300 : Chamber Volume : 340 liters Includes 2 pc PS 54 Platelet Agitator Temperature range: 20 C to 35 C Interior chamber: Stainless steel Convenient observation of platelet bags with interior illumination and large window High density injecte polyurethane insulation Perfectly insulated triple glass window and stainless steel frame Antifogging inner glass for avoiding condensation and outer glass blocking UV light Prevention of air leakage from the chamber and ambient ingress with magnetic gasket Protection against inadvertent and unauthorized access by using a key lock Excellent temperature uniformity and stability with powerful air circulation system Platelet protection because of quick recovery time after door openings Simple and safe operation using a microprocessor control system Highly visible, large LED display with 0.1 C resolution Optional NüveBank temperature data tracking and storage software and RS 232 port Power switch with key lock to prevent the platelet incubators from unauthorized use Audible and visual alarm system Alarm system is fed by automatically recharged battery Display of actual temperature even at power failure Battery operated 7-day chart recorder Standard remote and central alarm ports Optional AlerText SMS alarm system for ultimate security Optional NüveWarn remote alarm system
10 EN SER S MN MN CLASS II MICROBIOLOGICAL SAFETY CABINETS Two models with different working table width: MN 090: 89 cm / MN 120: 119 cm. First class protection for operator, environment and product. Microprocessor control system with digital display for air flow speed. Two HEPA filters with % efficiency for particles 0.3 μm. Automatic speed compensation system against clogged filter. Mains power switch with key lock. Alarms for: Power failure, control system failure, open window, low and high air flow speed, clogged filters. Perfect air tightness of window seal by means of gas spring assisted window. Comfort of usage with very quiet blower and high light intensity. Smooth chamber walls and rounded corners without soldering for easy cleaning and decontamination. Stainless steel and removable 3 pcs. work table. DOP test inlet, elapsed time counter and 2 pc. power socket as standard. EN Certificate for MN 120. LN LN LAMINAR FLOW CABINETS Two models with different working table width: LN 090: 89 cm. LN 120: 119 cm. Designed for the applications with non-hazardous materials in particle free environment for complete product protection. Single piece working table made of stainless steel for easy cleaning and decontamination. Pre-filter with 85 % efficiency for particles 0.5 μm ; HEPA filter with % efficiency for particles 0.3 μm. Microprocessor control system with digital display for air flow speed. Automatic speed compensation system against clogged filter. Audible and visible alarm for lower or higher airflow speed. Recirculated HEPA filtered air to prolong the lifetime of pre and HEPA filters. High light intensity and low noise level. Elapsed time counter and 2 pcs. power socket as standard. DOP test inlet.
11 Chamber volume: 12 liters. Temperature range: 110 C / 140 C. Used for the sterilization of unwrapped medical or dental instruments. Programmable microprocessor control system. Easy to use control panel, including digital displays for temperature and time. Proportional heating system. Manometer for chamber pressure. Safety valve against over-pressure. Very simple operation without any water or drain connection. 012 OT OT 012 BENCH TOP STEAM STERILIZER B & S CLASS BENCH TOP STEAM STERILIZERS OT 18B/23B OT 23S OT 23VS/32VS STEAMART Type of Sterilization Loads: B Models: All wrapped, un-wrapped, solid, hollow load products Type A* and porous products. VS models: Non-wrapped solid products, porous products, small porous items, hollow load products Type B*, single wrapped products, multiple-layer wrapped products. S model: Non-wrapped solid products, single wrapped products. Programs: B & S models: Universal, Quick, Gentle, Prion VS models: Universal, Wrapped Materials, Gentle, Quick, Prion Test Programs: B models: Bowie & Dick / Helix Test and Vacuum Test VS models: Bowie & Dick and Vacuum Test Seamless chamber for 18 and 23 liters models. Fractionated pre-vacuum system for B and VS models. Fractionated gravity system for OT 23S Advanced microprocessor control system with 128x64 pixels LCD display. Process evaluation system. Comprehensive self-diagnostic system. Memory for last 52 cycles. Reminder for cleaning and maintenance. RS 232 port for printer, NüveStore SD card writer or NüveSteamArt softwere for traceability. Conforms to the requirements of EN standard. Chamber Capacity: OT 18B : 18 liters OT 23B, OT 23S, OT 23VS : 23 liters OT 32VS : 32 liters * As defined in EN Standard
12 OT 100V OT 100V VERTICAL STEAM STERILIZER Chamber volume : 100 liters Advanced technology for the sterilization of textile; wrapped or packed materials; glass and liquid Fully automatic system leaves user free for other important work Integrated steam generator for fast production of steam Maintenance-free diaphragm type powerful vacuum pump Fractionated pre-vacuum to eliminate all air bubbles and achieve 100% steam penetration Fractionated post-vacuum for efficient drying of the samples Sterilization quality matching the needs of EN 285 European Standard for Large Steam Sterilizers Pre-heated chamber to eliminate condensation on the chamber walls and speed up the heating of the samples Easy to use microprocessor control system with 128x64 pixels LC display 5 preset programs : Universal, Solid, Prion, Quick, Gentle 6 special programs including liquid sterilization at 121 C Test programs for Bowie & Dick / Helix and vacuum leakage Memories for the last 25 cycles Cycle counter records the number of the operated cycles in the memory RS 232 port for printer NüveStore SD card writer or NüveSteamArt software for traceability Password protected Service menu Process evaluation system Comprehensive self diagnostic system for possible failures Ergonomic and user friendly design conforming to 93/42/EEC MDD Medical Device Directive, EN 285 European Standard for Large Steam Sterilizers and 97/23/EEC PED Pressure Equipment Directive OT 40L/90L OT 40L / 90L LABORATORY STEAM STERILIZER Chamber volume: OT 40L: 40 liters, OT 90L: 90 liters Maximum capacity : OT 40L: 2x5 liters, OT 90L: 3x8 liters Sterilization temperature range : 105 C C Especially developed for the steam sterilization of liquid and culture media Advanced microprocessor control system with 128x68 pixels LC display 5 preset programs : 2 for liquid and 3 for solid 2 custom made programs for liquid and solid Programmable melting program : 60 C C Programmable pre-heating : 40 C - 60 C Memory for last 25 cycles Programmable delayed start function Flexible temperature sensor to measure the exact liquid temperature Cooling by forced air ventilation over chamber Fractionated exhaust system for sensitive materials such as glass Comprehensive self-diagnostic system Chamber made of 316L stainless steel Manometer for chamber pressure Validation port RS 232 port for printer NüveStore SD card writer or NüveSteamArt software for traceability Safety precautions for lid opening depending on the type of the sterilized material
13 OT 300 / 430 / 570 STEAM STERILIZERS STEAMART Conforms to the requirement of EN 285 European Standard for Large Steam Sterilizers. Chamber and STU capacity : OT 300: 300 liters, 4 pcs. STU OT 430: 430 liters, 6 pcs. STU OT 570: 570 liters, 8 pcs. STU Ideal design for the steam sterilization of packed or unpacked surgical and dental instruments, operation linen, glass, plastic, rubber and silicon materials, infusion liquids, microbiological cultures and medical waste. Chamber, steam jacket, door and steam generator made of 316L stainless steel and conform to PED 97/23/EC Pressure Equipment Directive. Pneumatically controlled door opening with safety system. Steam driven one piece chamber gasket made of silicon. High capacity, low noise water ring vacuum pump for vacuum function. High quality valves, sensors and transmitters for a problem free and safe operation. Pneumatic valves in the steam lines. Innovative AIR COOLING system for low water and energy consumption. PLC control system with 7 colorful touch screen Wide screen allows monitoring all related information regarding sterilization cycle. 6 preset programs, 50 custom made programs. Two test programs: Bowie&Dick and vacuum leakage. Memory for last 28 cycles. Independent control system besides the main control system to record the data related to every cycle. Comprehensive self diagnostic system for possible system malfunctions. Service menu to detect the problem in case of a failure. Thermal printer offered as standard. Optional RS 232 port and software. Double door versions with 3.3 touch screen on the clean side: OT 430D and OT 570D.
14 TK 120/252/600 TEST CABINETS TK Three different sizes: 120, 252, 632 liters Economical solution to simulate real environmental conditions by controlling temperature, humidity and day & night cycles. Excellent design for different purposes in different sectors such as: Electric and electronic industry, automobile industry, automobile supply industry, chemical industry, plastic industry, textile industry, pharmaceutical industry, food industry, packaging industry, plant growth, seed germination, incubation and rearing of insects. Wide range of temperature control: -10 C/ +60 C (lights off), 0 C/ +60 C (lights on). Programmable humidity range: 20 % - 95 % Rh. (between +10 C / +60 C). Programmable alarm range: 2-10 C, 5-20 % Rh. Powerful illumination by means of the lights located inside the door Max. lighting level: TK 120: lux, TK 252 / 600: lux. Programmable lighting timer: 0-24 hours. Easy to use programmable microprocessor control system. 10 program memories. 9 program steps for temperature and humidity. User friendly control panel with 128 x 64 pixel LC display. 32 Kb standard, 256 Kb optional memory. Chamber made of stainless steel. Ø 25 mm. access port. Internal glass door. Humidity produced by the humidity generator. Self-diagnostic system for possible failures. Adjustable safety thermostat for heating. Outlet for printer connection for printing current or stored programs. Optional NüveGrowth software for programming and controlling via PC. CFC-free refrigerant and insulation. GC 400 GC 400 GROWTH CHAMBER Advanced technology for tests at different climatic and lighting conditions such as plant growth, seed germination, acclimation of plants, culture of plant cells and tissues, genetic manipulations of plants, cultivation of protoplasm and cells, incubation and rearing of insects. Chamber volume: 400 liters. Wide range of temperature control : -20 C / +60 C (lights off), 0 C/+60 C (lights on) Programmable humidity range: 20 % / 95 % Rh (between +10 C and +60 C). Programmable alarm range: 2-10 C, 5-20 % Rh. Lighting from three sides: Left, right and up. Max. lighting level: lux. Programmable lighting function: 0-24 hour timer for each side. Door mounted, state-of-art programmable microprocessor control system. 10 program memories. 9 program steps for temperature and humidity. Programmable altitude for calculating right humidity value according to psychrometric formula. User friendly control panel including 128 x 64 pixel LC display. Chamber made of stainless steel and glass windows. Humidity produced by a humidity generator. Humidity measurement according to pyschrometric diagram. Self-diagnostic system for possible failures. 32 Kb standard, 256 Kb optional memory. Adjustable electronic safety thermostat. Outlet for printer connection for printing current or stored programs. Optional NüveGrowth software for programming and control via PC. CFC-free refrigerant and insulation.
15 300 Ideal design for the tests at different climatic conditions and stability, artificial aging and storage tests in industries such as electronic, automobile, automobile supply industry, aircraft and aviation, chemical, plastic, textile, pharmaceutical, construction material, food, packaging and military equipment. Chamber volume: 290 liters. Wide range of temperature control: - 40 C / +150 C. Programmable humidity range:15 % - 98 % Rh (Between 10 C / 90 C). Door mounted state-of-art programmable microprocessor control system. Ten program memories. Programmable 9 step for temperature and humidity. Programmable altitude to calculate the right humidity value according to psychrometric formula. User friendly control panel including 128 x 64 pixel LC display. Stainless steel chamber. Ø80 mm access port on the right side. Triple insulation consisting of high density injected polyurethane, glass wool and aluminum layer. Heated door window with quintuble glass for perfect insulation. Interior lighting. Producing humidity by dew-point bath. Humidity measurement according to psychrometric diagram by means of the dry and wet bulb temperature. Self-diagnostic system for possible failures. Adjustable electronic safety thermostat. Possibility of connecting four pieces of PT 100 temperature sensor measure any four points in the chamber. 32 Kb standard, 256 Kb optional memory. Outlet for printer connection to print current or stored programs. Optional NüveClimate software program for control via computer. CFC-free refrigerant and insulation. ID 300 CLIMATIC TEST CABINET ID ID 300 CLIMATIC TEST CABINET
16 The Right Choice for the Right Results A Strong Foundation Established over 40 years ago in 1968, NÜVE is one of the fastest expanding manufacturers of laboratory and sterilization instrumentation in the world today. Quickly becoming market leader in our home country, the major proportion of our production is today exported to over 90 countries worldwide and the brand is established as a driving force in the development of new products. Quality & Reliability Quality is a keyword for NÜVE. This is proven by its certification to ISO 9001:2008 and ISO 13485:2003. Combining this with a strong ethic of providing outstanding value, NÜVE incessantly strives to increase efficiency through evolution of its working practices and investment in the latest machine tools. Top class components and high grade raw materials ensure that the final product is something that the user can be proud of. An important factor in the high level of reliability is the commitment of the production team, half of which has been with the company for over 20 years. Investment & Expansion Substantial investment in R&D enables NÜVE to offer an ever-widening range of quality products. A team of highly qualified and experienced engineers has been producing instruments with unique characteristics bringing additional benefits to our customers. The offer in the field of biology in particular has significantly expanded and the level of technological innovation is proven by the large number of trade-marked features recently introduced in the range. NÜVE has been growing continuously and strongly, even during the recent worldwide economic crisis. With its dedication to customer service, NÜVE is committed to ensuring the supply to its customers on time. During the last seven years, the size of the production plant was doubled as were the number of machine tools for production. Wide Ranging Markets NÜVE products are designed and developed for a broad spectrum of markets including clinical laboratories, medical research, biotechnology, agriculture, veterinary labs, food, beverage and dairy, chemicals, automotive, aerospace, ceramics, water and pharmaceutical industries. Professional Support As we innovate, we educate. Recognizing that education is key onto the continuous growth of the company and its products, NÜVE is committed to providing relevant, leading-edge educational opportunities throughout the year for its distributors. Comprehensive distributor training in products and after-sales servicing by NÜVE experts ensures professional local support for customers and an excellent return on the investment in this innovative brand. Some recent instruments include the facility enabling NÜVE engineers to carry out analysis and even updates remotely from the NÜVE headquarters, keeping customer products on top performance. We reserve the right to modify the design and description. NÜVE SANAYİ MALZEMELERİ İMALAT VE TİCARET A.Ş. Esenbo a Yolu, 22 km. Akyurt ANKARA TURKEY Tel : ( ) (pbx) Fax : ( ) ISO 9001: 2008 ISO 13485: /Z15.K
OT 40L / 90L Laboratory Steam Sterilizers OT 40L / 90L LABORATORY STEAM STERILIZERS OT 40L / OT 90L laboratory steam sterilizers are specially designed for the steam sterilization of liquid and culture
Laboratory Line Vertical and Bench-Top Life Science Autoclaves The Advanced Laboratory Line The Full Spectrum of Laboratory Sterilizers Sterilization in a laboratory environment has its unique requirements.
Vertical and Benchtop Autoclaves for Life Sciences Laboratory Line Designed for Your Laboratory Applications Advanced Laboratory Autoclaves Tuttnauer laboratory autoclaves have been designed to provide
NÜVE SANAYİ MALZEMELERİ İMALAT VE TİCARET A.Ş. OT 020 BENCH TOP STEAM STERILIZER USER S MANUAL NÜVE SANAYİ MALZEMELERİ İMALAT VE TİCARET A.Ş. Esenboğa Yolu 22 km Akyurt - ANKARA / TURKEY Tel : (00 90 312)
FP series 400 Material test chambers Material test chamber with mechanical convection A BINDER material test chamber with mechanical convection of the FP series provides reliably short drying times and
BF series 400 Incubators and cooling incubators Incubator with mechanical convection The BINDER incubator of the BF series with mechanical convection is suitable for all gentle incubation applications,
LABOKLAV Autoclaves Made in Germany www.shp-steriltechnik.de 2 LABOKLAV STEAM STERILIZERS Steam sterilization is the sterilization method with the widest range of applications efficient, safe, reproducible
VD series 53 Vacuum drying ovens Vacuum drying oven for non-flammable solvents A BINDER vacuum drying oven of the VD series is impressive while gently drying with its homogeneous temperature distribution.
ED series 53 Drying ovens / Heating ovens Heating oven with mechanical control The strength of the BINDER ED series heating oven: routine drying and sterilization applications up to 300 C (572 F). Thanks
Freezers - Ultrafreezers Platilab & Irilab Series PLATILAB: top security and performances with reliable temperature control. IRILAB: combining the high reliability of PLATILAB with the possibility to store
Sterilizers with extra class ClassB Ready for the future The European standard EN 13060 specifies the performance requirements and test methods for small steam sterilizers. These are used for hygiene and
08-80 C FREEZERS PowerFREEZE TM -86 C Freezers VXE/VXS Series, Jouan VXS490 PowerFREEZE cooling system VXE490 Exclusive PowerFREEZE cooling system in each shelf eliminates freeze-thaw cycles, reduces ice
FD series 53 Drying ovens / Heating ovens Heating oven with mechanical convection A BINDER FD series heating oven is always used when fast drying and sterilization is required. Thanks to its fully homogeneous
AUTOCLAVE STEAM STERILIZERS (BENCH TOP) Image: HS-1606VD Hanshin Bench Top Steam Sterilizer Small and easy to operate Three preset sterilization cycles Adjustable cycle presets Rapid heat up times Option
VERTICAL AND HORIZONTAL HEPA FILTERED SYSTEMS FOR PROCESS OR OPERATOR PROTECTION Laminar Flow Cabinets and Workstations For procedures requiring protection from particulate contamination and for aseptic
Partnership Medical Waste Autoclaves Medical Waste Autoclaves Safe, Cost-Effective, Medical Waste Sterilization Keep your environment safe from Medical Waste with high performance Tuttnauer Medical Waste
Microbiological Incubators Safe, easy and efficient Microbiological Incubators your samples We are obsessed with sample integrity. Each of our new laboratory microbiological incubators is designed with
KBWF series (E5.2) Climate chambers with illumination Climate chamber with illumination The BINDER climate chamber with illumination of the KBW series achieves homogeneous light distribution with its natural
Centurion Scientific Limited Making Science Look Good Quality Profile Within the following pages, we show what makes up the quality of our centrifuges and why we are so successful. Not only do we use the
FVA/A1 where technology innovation and design come together FVA/A1 saturated-steam sterilizer www.fedegariautoklaven.ch Fedegari's new FVA/A1 series of automatic vertical sterilizers has been expressly
Bench Autoclave Standard Operating Procedure For Installation, Use and Maintenance 1. Introduction This SOP is intended for use with the following model, in a laboratory context: Type: Nuve Bench Top Steam
Thermostatic Equipment comming soon (06/2015): Climatic Chambers with LED lighting Climatic Chambers with steam humidifier Peltier - Cooled Incubators Refrigerators with back - up system ultra - Low Freezers
Characteristic: The process of pre-freezing and drying finishes in situ. The freeze dryer is equipped with observation windows and the drying process is intuitive. Silicone oil is as the medium and the
KR25i HIGH SPEED, HIGH CAPACITY REFRIGERATED CENTRIFUGE AUTO-LOCK CQCS Traceability System VIDEOset Display! A CENTRIFUGE FOR ALL YOUR HIGH SPEED APPLICATIONS CLINICAL BIOLOGY, RESEARCH, INDUSTRY The KR25i
BSL3 and BSL4 Autoclaves Laboratory Line BSL3 and BSL4 Autoclaves In today s society the need for safe bio-containment systems is increasingly important. This is especially true in the sterilization process
Large Steam Sterilizers for the Life Sciences Laboratory Line Large Steam Sterilizers for the Life Sciences Sterilization in a laboratory environment has its unique requirements. The types of loads that
Refrigerators - Freezers Ekofrigolab & Ekobasic Series Angelantoni Life Science S.r.l. manufactures a wide range of refrigerated cabinets and combined refrigerator/freezer cabinets. We offer high reliability
Hospital Sterilizers T-Max Line Hospital Sterilizers Sterilization is a complex process. Like any complex process, many things can go wrong. A Hospital depends on its CSSD: Central Sterile Services Department.
Steam Sterilization Cycles for Lab Applications Presented by Gary Butler STERIS Life Sciences August 2009 Early Steam Sterilizers Koch Upright Sterilizer First Pressurized Sterilizer First built by Pasteur-Chamberlain
Medical Waste Autoclaves Medical Waste Autoclaves Safe, Cost-Effective, Medical Waste Sterilization Treat Medical Waste with high performance Tuttnauer Medical Waste autoclave systems designed for small,
Clinic Washer-Disinfectors Washer-Disinfector Line Easy-to-Use Washer-Disinfectors for Clinics The Clinic Range of Washer Disinfectors provides superior cleaning and disinfection combined with innovative
LAMINAR FLOW CABINETS Vertical Laminar Flow Cabinets VLF 550 VLF650 VLF1000 VLF1200 VLF 1500 VLF1800 Monmouth Scientific's brand new range of Vertical laminar Flow (VLF) cabinets is available in six different
ORGANIC SAMPLE PREPARATION W W W.LA BT E C H S R L.CO M WSPE MANUAL VACUUM MANIFOLD SPE Process control of the flow rate is critical to guarantee reproducible extractions. Differently then any other systems,
Shakers, Incubators, Clean Benches, Water Baths, Drying Ovens Ask for catalogues and brochures Learn distribution terms and conditions Download brochures and leaflets Register for monthly newsletters Check
FR / MF I Deep Freezers & Plasma Storage Freezers 292.9707.70 09/2015 > Low-temperature storage of plasma and other blood products at 41 C / 35 C > According to DIN 58375 & Medical Device 93/42/EEC BIOMEDICAL
German engineering under high pressure Over 25 years of experience as a manufacturer of sterilizers, autoclaves and lyophilization systems for laboratories, production and research Production-scale autoclaves
1 CO2 Incubator Model CCL-170_-_ CO2 Incubator with Integrated Cooling System Solution for Highly Specialized Applications Welcome to Esco Esco s Vision is to provide enabling technologies for scientific
Technology for Life Medical SYSTEMS Technology for Life BR I Blood Bank Refrigerators +4 C 292.9707.50 08/2013 BIOMEDICAL REFRIGERATION Innovative and reliable refrigeration solutions compression Refrigerators,
The key difference between a small vertical or bench-top sterilizer and industrial sterilizer is performance. Small saturated-steam sterilizers with vertical or horizontal chambers were devised many years
PRINTED CIRCUITS EQUIPMENT PRINTED CIRCUITS EQUIPMENT Insulator machines Echting machines Special equipment and machines On customer request it is possible to supply: Benches for PCB Oven for PCB Chemicals
Cooking at the Infrared Cooking & Colouring Infrabaker is a modular infrared continuous cooking system developed by Infrabaker International. The machine is designed to cook and/or put colour on a wide
Tabletop Line Automatic and Semi-Automatic Autoclave Series Tuttnauer Your Sterilization & Infection Control Partner Company Profile For over 80 years, Tuttnauer s sterilization and infection control products
Laboratory & Scientific Line Bulk Steam Sterilizers Since 1925 Bulk Steam Sterilizers for Laboratory & Scientific Applications The Tuttnauer line of bulk autoclaves are designed to handle the most critical
ooled Incubators ooled incubators ooled incubators () are available in two versions: STD and TOP. STD STANDARD VERSION extended possibilities reasonable price wide range of optional equipment stainless
Laminar Flow Cabinets The World s Most Practical Selection of Benchtop Laminar Flow Cabinets. 24 36 48 Simple, Effective Protection for Samples and Work Processes, Uncompromised Performance, Economical
Thermo Scientific Sorvall T3 and G3 Centrifuge Series Capacity, reliability and performance for routine applications Capacity, reliability and performance for routine applications The Thermo Scientific
The Power of Innovation. For better Sterilization. Autoclaves: Systec V-Series t h e a u t o c l a v e c o m p a n y Systec V-Series: Vertical autoclaves. These autoclaves don't just seem to be different;
NewAir AC-10100E / AC-10100H Portable Air Conditioner Owner s Manual PLEASE READ AND SAVE THESE INSTRUCTIONS ELECTRICAL SAFETY This appliance is for indoor use only. Always turn off the unit and unplug
Eurovacuum EV Series Single Stage Oil Sealed Rotary Vane Pump Eurovacuum EV Series Single Stage Oil Sealed Rotary Vane Pumps Eurovacuum Company is offering its various products to meet industrial vacuum
Kompressoren Adsorption Dryer AD Adsorption Drying: why? Modern industries require compressed air that is increasingly filtered with low dew point and condensate. Today, the equipment is more sophisticated
Temperature control and cooling systems The innovative and reliable solution With our PulseTemp equipment you have the option of up to 72 cooling circuits in the impulse cooling, temperature control, temperature
Laboratory- and sterilisation equipment HMC EUROPE PROFILE HMC EUROPE Laboratory- and sterilisation equipment Consistent marketing of technologies and the conversion of new ideas create product ranges,
Partnership Large Steam Autoclaves for the Life Sciences Laboratory Line Large Steam Autoclaves for the Life Sciences Sterilization in a laboratory environment has its unique requirements. Tuttnauer laboratory
APPLICATIONS Heating, ventilation, cooling >> FACTORIES >> WAREHOUSES >> HALLS >> DISTRIBUTION CENTRES >> COMMERCIAL PREMISES >> PLACES OF WORSHIP RPV - RP - RA air handling units www.reznor.eu RPV - RP
The Power of Innovation. For better Sterilization. Pass-through autoclaves: Systec D-Series 2D Horizontal front loading bench-top autoclaves: Systec D-Series t h e a u t o c l a v e c o m p a n y Systec
PIZZA CHEF COUNTERS PIZZA CHEF COUNTERS PZ2037A EURONORM PZ REFRIGERATED COUNTER: TECHNICAL FEATURES - All-in-one structure with an insulating thickness varying from 60 mm to 40 mm; the insulation is ensured
LyoBeta R+D Freeze-Dryers LyoBeta series A Responsible Choice New demands in R+D centers are related to scale-up feasibility and quality of procedures and research methods. FDA investigators consider that
Vertical Laminar Airflow Cabinets PROTECTION, SAFETY, RELIABILITY. AND MORE. Vertical Laminar Flow Cabinets BEYOND MINIMUM SAFETY REQUIREMENT Cabinets are ISO Class 3 vertical laminar flow cabinets which
WATERBATHS AND OILBATHS New bath generation, still more accurate through innovative control technology Combined start delay and hold time; on Excellent models setpoint-dependent More security through at
Laminar Flow Cabinets The World s Most Practical Selection of Benchtop Laminar Flow Cabinets. 24 36 48 Purair FLOW-36 Simple, Effective Protection for Samples and Work Processes, Uncompromised Performance,
UNITOR VACUUM cleaners Unitor VCD15 a compact, heavy-duty dry vacuum cleaner for accommodation areas The smallest unit in the Unitor range, the VCD15 is purpose-made for use on cruise and passenger vessels.
Laboratory & Scientific Line Horizontal Steam Sterilizers Horizontal Steam Sterilizers for Laboratory & Scientific Applications Sterilization in a laboratory environment has its unique requirements. The
National Competency Based Skill Training Refrigeration and Air-conditioning Mechanic Logbook Trainee:... Training Provider:... Year:... Trainee Contact no:... Competency Based Skill Training Logbook Introduction
KONRAD Hybrid Fancoil Series Konrad is an innovative radiator which cools you down and warms you up. Indeed, it cools in summer and heats in winter; but it makes it with an incomparable quietness. Thanks
Water Baths with BioCote antimicrobial protection Water Baths are one of the most common pieces of laboratory equipment used today, the Stuart range offers three sizes 6, 15 and 24L with digital control.
SECTION 23 81 03 - PACKAGED ROOFTOP AIR CONDITIONING UNITS NON-CUSTOM PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Packaged rooftop air conditioning unit (5 tons and smaller). 2. Roof curb. 1.2
TRADE R AUTOCLAVES FOR STERILIZATION AUTOCLAVES STEAM STERILIZATION AUTOCLAVES RAYPA autoclaves are manufactured according to the following directives and rules: 97/23 CE.- Directive pressure equipments.
Blood Bank Refrigerators according to DIN 58371 Blood Plasma Freezers according to DIN 58375 1865 Philipp Kirsch establishes the company as a coppersmith firm 1901 Beer cooling cylinders are produced 1927
Fresh quotations in sealed envelope are invited addressed to The Principle, Deshbandhu College, for the purchase of equipment required for Innovation Project 2015-16 Closing date is 15 November, 2015 List
55-1 GROUP 55 HEATER, AIR CONDITIONING AND VENTILATION CONTENTS GENERAL DESCRIPTION 55-2 HEATER AND AIR CONDITIONING SYSTEM 55-4 HEATER CONTROL 55-6 A/C-ECU 55-7 A/C COMPRESSOR 55-9 CONDENSER 55-9 DUCT
POLAR EDITION -86 C ULTRALOW FREEZER MODEL NU-9728-86 C ULTRALOW TEMPERATURE FREEZERS NuAire, Inc. 2100 Fernbrook Lane Plymouth, MN 55447 U.S.A. 763.553.1270 WWW.NUAIRE.COM POLAR EDITION -86 C ULTRALOW
NewAir AC-14100E / AC-14100H Portable Air Conditioner Owner s Manual PLEASE READ AND SAVE THESE INSTRUCTIONS PARTS LIST Front Back FIG.5 FIG.6 1. Control panel 2. Carrying handle 3. Water tank 4. Casters
PART 1 - GENERAL 1.1 DESCRIPTION SECTION 11 78 13 MORTUARY REFRIGERATORS SPEC WRITER NOTE: Delete between //---// if not applicable to project. Also delete any other item or paragraph not applicable in
Solar Hot Water Heaters Three High Vacuum Water inlet Stainless Steel screw Gel seal and insulation Water outlet Dust proof seals Non Pressure Models Details ASWH-1b ( Color Painted 304 ) ASWH-1c ( stainless
-3ºC Biomedical Freezers With Inverter Control KM-MU28H1E / KM-MU9H1E l NEW inverter compressor technology delivers energy saving, high performance cooling l Outstanding reliability and performance for
WHY GRUENBERG DRY HEAT STERILIZATION? Design assistance from leader in lab animal science sterilization Lowest total cost of ownership Greater output in a smaller footprint Safer operation Extended cage
SECTION 15750 PART 1 - GENERAL 1.01 DESCRIPTION A. Section includes requirements for roof mounted, self-contained units, with electric cooling, and electric or reverse refrigeration cycle (heat pump) heating
CRAC Precision climate control units for data centres 2 Rittal Computer Room Air Conditioner The whole is more than the sum of its parts The same is true of Rittal The System. With this in mind, we have
-86 C ULTRALOW TEMPERATURE FREEZERS NuAire, Inc. 2100 Fernbrook Lane Plymouth, MN 55447 U.S.A. 763.553.1270 www.nuaire.com NuAire Glacier -86 C Ultra-low Temperature Freezer NuAire Glacier -86 C Ultra-low
Adsorption air dryers ADS 25 INDUSTRY CUSTOMER SERVICE COMPRESSED AIR AIR INTAKE 20 C 70% UR 760 mm Hg 2 grh 2 O/m 3 AIR PRESSURE 0 bar COOLING SYSTEM 30 C 00% UR 0 bar 2,8 grh 2 O/m 3 A compressor that
STATIM G4 Cassette Autoclaves From start to dry in the blink of an eye. STATIM, the world s fastest autoclave from start to sterile Drawing on over 20 years of innovation, Healthcare practitioners in over
Vacuum drying ovens VDL 53 - Vacuum drying oven for flammable solvents The VDL series ensures maximum safety when drying organic solvents in accordance with TÜV/GS guidelines. The interior chamber is designed
18 LITER VOLUME STERILISATION MATERIALS TESTING MEDIA PREPARATION Applications THE WIDE RANGE OF USING CERTOCLAV AUTOCLAVES MICROBIOLOGY / BIO-CHEMISTRY Autoclave culture mediums Refuse sterilisation Efficiently