Datasheet. 1-slot or 4-slot Chassis. Feature. Specifcation. Ordering Information. Compliance. Raisecom Technology Co., Ltd. RC001-1-DC Chassis

Transcription

1 1-slot or 4-slot Chassis In small-capacity situation, Raisecom presents its 4-slot chassis RC001-4, 4-slot network manageable chassis RC002-4 and singleslot chassis RC001-1 to meet customer requirements of installing and/or managing different service modules, including media converter, fber optic modem, PDH multiplexer, interface converter, G.SHDSL modem and CWDM cards, concentratedly on one platform. RC001-4 and RC002-4 have identical structure and dimension.the only difference is that RC002-4 has an in-built SNMP agent module, and through which the four service modules in RC002-4 can be network managed. Fixed in RC001-1 series single-slot chassis, Raisecom's modular devices become standalone equipments, and can be either placed on table or mounted on wall or rack with accessories. The employment of power supply connector of RC001-1 depends on customer's need. Except for traditional connector for AC or DC power supply, an option of connector for wide-range power supply is provided. RC001-1-DC Chassis RC001-1-AC/WP Chassis Slot Number Power Protection Network management RC001-1-AC RC001-1-DC RC001-1-WP RC001-1 Rack- Mount Tray RC001-1 Rack- Mount Angle RC001-1 Wall- Mount Angle RC001-4-AC RC001-4-DC RC002-4-AC RC002-4-DC RC001/RC002-4 has 4 slots; RC001-1 has one slot. AC: 100~240V, 50/60Hz; DC: -72~-36V DC WP: 100~240V AC or -72~-36V DC (the WP power supply connector will adapt to the factual power supply automatically) overcurrent protection, short circuit protection RC002-4 is a chassis with in-built SNMP agent module. The SNMP agent module enables the network managment over service modules in RC002-4 and their peer devices. 1U, 1-slot chassis, with AC power supply connector 1U, 1-slot chassis, with DC power supply connector 1U, 1-slot chassis, with WP wide-range power supply connector that adapts to the factual power supply (AC or DC) automatically Accessory for installing RC001-1 chassis on 19" rack, two RC001-1 can be placed on one tray. Accessory for installing RC001-1 chassis on 19" rack, one RC001-1 uses two rack-mount angles Accessory for installing RC001-1 chassis on wall, one RC001-1 users two wall-mount angles 1U, 4-slot chassis, with AC power supply connector 1U, 4-slot chassis, with DC power supply connector 1U, 4-slot chassis with in-built SNMP management agent and AC power supply connector 1U, 4-slot chassis with in-built SNMP management agent and DC power supply connector RC001/RC002-4 Chassis Specifcation Dimension RC001/002-4: 440x44x266mm (WxHxD) RC001-1: 158x40x200mm (WxHxD) Power RC001/002-4: 40W Consumption RC001-1: 10W Working 0~45 degree Celsius Relative Humidity 5%~95% Storing -40~70 degree Celsius Compliance Standards UL,CE,FCC, CSA complied with IP30

2 RC001-1D single-slot chassis RC001-1D is a single-slot chassis designed for service modules that take up 2 slots in RC It is applicable for telecom carrier and important enterprise user in the feld of fnance, electric power, petroleum industry, and etc. To provide high service capacity, some of Raisecom's modular devices, including Ethernet to 4/8E1 interface converters, PDH multiplexers providing 4/8 E1 channels, and multi-service multiplexers providing 4/8/16 plus 1 Ethernet Connector Power Protection Slot Number service, occupies 2 slots in RC Fixed in RC001-1D, these modular devices become stand-alone equipments, and can be either placed on table or mounted on wall or rack with accessories. The employment of power supply connector depends on user's need. Except for traditional connector for AC or DC power supply, an option of connector for wide-range power supply is provided. AC power supply connector for AC power supply or DC power supply connector for DC power supply or WP power supply connector adapted to the factual power supply (AC or DC) automatically overcurrent protection 1 slot, with the width of 2 slot of RC RC001-1D-AC RC001-1D-DC RC001-1D-WP Rack-Mount Tray Rack-Mount Angle Wall-Mount Angle Application single-slot chassis, with a connector for AC power supply single-slot chassis, with a connector for DC power supply single-slot chassis, with a connector automatically adapted to the factual power supply (AC or DC) accessory for fxing RC001-1D on to 19-inch rack accessory for fxing RC001-1D on to 19-inch rack accessory for mounting RC001-1D on wall RC001-1D Front Panel Specifcations Dimension 158x64x200mm(WxHxD) AC 100~240V, 50/60Hz DC -36V~-72V Power less than or equal to 15W Consumption Working -5~55 degree Celsius Humidity 5%~95% Storing -40~70 degree Celsius Compliance Standards CE and UL Service Modules in RC001-1D Ethernet to E1 Interface Converters RC954-FE(FX)4E1, RC954-2FE4E1-BL, RC954-2FE8E1-BL PDH Multiplexer RC L, RC L(-BL) Multi-Service PDH Multiplexer RCMS LFE(-BL), RCMS LFE(-BL), RCMS LGE(-BL), RCMS LGE(-BL)

3 RC001-1M single-slot network-manageable chassis RC001-1M is a single-slot chassis with in-built SNMP management module. It is designed for telecom carrier and important enterprise user in the feld of fnance, electric power, petroleum industry, and etc. Fixed in RC001-1M, modular media converters, PDH multiplexers, interface converters, G.SHDSL modems and other modules designed for 1U slots become standalone and network-manageable equipments. The SNMP agent module built in RC001-1M realizes network management function like confguration management, diagnostics, loop activation, monitoring and fault management. There is one console port, one Ethernet port and one slot for modular device on the front panel. The AC and DC power supply connectors on the rear panel of RC001-1M provides users with the fexibility of using AC power supply, or DC power supply or both of them. RC001-1M Front Panel Power Protection Slot Number InterfaceType Netwrok Management AC power supply, or DC power supply, or both AC and DC power supply overcurrent protection, short circuit protection, overheat protection 1 slot 1 SNMP interface for network management 1 CONSOLE interface for initial confguration of SNMP network management over the service module in the RC001-1M and the device on the opposite side of the communication RC001-1M Application single-slot chassis, with inbuilt SNMP network management agent module, 1 AC and 1 DC power supply connector RC001-1M Rear Panel Specifcations Dimension 260x38x190mm(WxHxD) AC 100~240V,0.35A,50/60Hz DC -48V,0.6A Power less than or equal to 15W Consumption Working 0~45 degree Celsius Humidity 5%~95% Storing -40~70 degree Celsius Compliance Standards CE and UL Service modules working and managed in RC001-1M RC1~RC6 series media converters RC8xx series PDH multiplexers providing 1/2/4 E1 channels or 1 DS1 channel or 1 DS3/E3 channel Multi-service PDH multiplexer RCMS2x01 series and RCMS GE-BL RC9xx series Ethernet to E1, Ethernet to DS3/E3, Ethernet to V.35, V.35 to E1 interface converters OPCOM200 series CWDM modular equipments RC1102 series G.SHDSL modem

4 Preliminary RC001-2M dual-slot network-manageable chassis RC001-2M is a dual-slot chassis with in-built SNMP management module. It is designed for telecom carrier and important enterprise user in the feld of fnance, electric power, petroleum industry, and etc. Fixed in RC001-2M, modular media converters, PDH multiplexers, interface converters, G.SHDSL modems and other modules that take up 2 slots in RC become stand-alone and network-manageable equipments.the SNMP agent module built in RC001-2M realizes network management function like confguration management, diagnostics, loop activation, monitoring and fault management. There is one console port, one Ethernet port and two slots for two units of individual single-slot width modular device or one unit of 2-slot width modular device on the front panel. The AC and DC power supply connectors on the rear panel of RC001-2M provides users with the fexibility of using AC power supply, or DC power supply or both of them. RC001-2M Front Panel RC001-2M Rear Panel Power Protection Slot Number InterfaceType Netwrok Management Single AC power supply, or single DC power supply, or both AC and DC power supply with two individual connectors or a auto-sensing connector overcurrent protection, short circuit protection, overheat protection 2 slots 1 SNMP interface for network management 1 CONSOLE interface for initial confguration of SNMP network management over the service module in the RC001-2M and the device on the opposite side of the communication RC001-2M-AC/DC RC001-2M-WP RC001-2M-AC RC001-2M-DC Dual-slot chassis, with in-built SNMP network management agent module, 1 AC and 1 DC power supply connecters Dual-slot chassis, with in-built SNMP network management agent module, 1 AC/DC auto-sensing power supply connecter Dual-slot chassis, with in-built SNMP network management agent module, AC power supply Dual-slot chassis, with in-built SNMP network management agent module, DC power supply Specifcations Dimension 320x65x200mm(WxHxD) AC 100~240V,0.35A,50/60Hz DC -48V,0.6A Power less than or equal to 15W Consumption Working 0~45 degree Celsius Humidity 5%~95% Storing -40~70 degree Celsius Compliance Standards CE and UL

5 Preliminary RC001-2M dual-slot network-manageable chassis Typical Application Dual-slot-width service modules working and managed in RC001-2M (02/2008) RC8xx series PDH multiplexers RCMS series Multi-service PDH multiplexers RC9xx series Ethernet over PDH(E1s) inverse multiplexers One-slot-width service modules working and managed in RC001-2M (02/2008) RC1xx~RC6xx series media converters RC8xx series PDH modem and multiplexers RCMS series Multi-service PDH multiplexers RC9xx series Ethernet over E1(s), Ethernet over DS3/E3, Ethernet over V.35, V.35 to E1 interface converters and inverse multiplexers OPCOM200 series CWDM modular equipments RC1102 series G.SHDSL modems Warning: The total power consumption of the 2 one-slot-width service modules working in RC001-2M must not exceed 12W.

6 RC slot Chassis with SNMP Management RC is a 19" rack-mountable 3U platform which supports two rear-loading, redundant, load-sharing, hot-swappable AC or DC power supplies. Up to 16 modular converters can be installed in the chassis, providing a CO/POP site solution for connecting up to 16 remote users (15 with SNMP function). RC is manageable access system for providing full convergence of the Last Mile with a variety of technologies, rates, interfaces and media. The system supports standard technologies G.703/704, G.SHDSL and IEEE Each card in the RC works in a point-to-point confguration opposite a remote Slot Number Up to 16 slots for modular converters Redundant Power Two rear-loading, redundant, load-sharing, hot-swappable AC or DC or one Supply AC and one DC power supplies Hot-wappable RC can operate with single or dual AC or DC power supplies. power supply Each power supply supports a full rack of any combination of cards. The redundant power supply can be replaced without affecting system performance Flexibility Single chassis for various modular converters with a variety of technologies, rates, interfaces and media Hot-swappable All cards are hot-swappable and can be replaced without interfering with the modular converters data transmission of other cards Safety Compliance CE and UL Effcient Heat Optimal structure for effcient heat dissipation dissipation Network The chassis can be managed by Raisecom network management platform Management Nview iems (graphic format), which allowing confguration management, diagnostics and loop activation, as well as monitoring and fault management Real-time confguration and monitoring unit with no connection to the adjacent cards. This allows each card to support a different rate, interface or media. All cards are hot-wappable and can be replaced without interfering with the data transmission of other cards. RC supports SNMP management with NMS1 card inserted. The network management software iems enables the user to change the setup confguration, get real-time alerts on system status, active diagnostics, and receive statistics on system functionality in a graphic format. The management software enables the user to change the setup confguration, get real-time alerts on system status, activate diagnostics, and receive statistics on system functionality in a graphic format. RC001-NMS1 RC001-NMS2 RC002-16AC/S RC002-16AC/D RC002-16DC/S RC002-16DC/D RC009-2AC RC009-2DC Mount Angle 21 Mount Angle 23 Network management master module for RC series modules, installed into 3U 16-slot chassis Network management slave module for RC series modules, installed into 3U 16-slot chassis 3U, 16-slot chassis with one AC power supply connector 3U, 16-slot chassis with two AC power supply connector 3U, 16-slot chassis with one DC power supply connector 3U, 16-slot chassis with two DC power supply connector Redundant AC power supply for RC Redundant DC power supply for RC Accessory for installing RC on 21" rack, two angles for one chassis Accessory for installing RC on 23" rack, two angles for one chassis Note: The RC chassis can be installed on 19" rack directly without any accessory. RC Specifcation Number of slot 16 Power supply Two hot-swappable AC or DC power supplies Input power AC: 185V-265V, 50/60Hz supply voltage DC: -36V- -72V Rated Current 20A Short Current Yes Protection Over Current 30A Protection Noise 100mVp-p Port CONSOLE: RJ-45 specifcation ETH (for SNMP and Telnet): (For NMS1 RJ-45 network Cascading port: RJ45 management card) Indicators PWR: for power supply PS1-5: PS1 for modules PS1-12: PS1 for 1st fan PS2-5: PS2 for modules PS2-12: PS2 for 2nd fan Dimension 442x130.5x350mm (WxHxD) Power 80W (at max load) consumption Working Temp: 0~50 degree Celsius RH: 5~90% non-condensing Storage Temp: -40~85 degree Celsius RH: 20~90% non-condensing Safety compliance RC001-NMS1 CE marking UL

7 RC002 Cascade With management agent master module RC001-NMS1 and slave module RC001-NMS2 connecting in the manner shown on the right, four RC chassis forms a cascade. At most sixty pairs of equipments at both local and remote sites can be managed through one IP address which is the IP address of RC001- NMS1. Typical Application

8 RC Chassis for PDH FOM Modular Devices RC is a 19" rack mountable 10U 16-slot chassis for Raisecom modular type Fiber Optical Modem (4E1, 8E1, 16E1 and 8E1+4ETH) and it has rear-loading, redundant, load-sharing,hot-swappable AC or DC power supply. Each card in the RC works in a point-to-point mode with a remote unit and so as to provide a CO/POP site solution for Fiber Optical Modem users. All cards are hot-swappable and can be replaced without interferring with the data transmission of other cards. RC supports SNMP network management with RC004-16NMS1 card inserted in slot 0, and along with the RC004-16NMS2 card cascade can be realized up to 4 RC chassis. The network management software NNM enables users to change the setup confguration, get real-time alerts on system status, active diagnostics, and receive statistics on system functionality in a graphic format. Slot Number Up 16 slots for modular converters Redundant Power Two rear-loading, redundant, load-sharing, hot-swappable AC or DC or one Supply AC and one DC power supplies Hot-wappable RC can operate with single or dual AC or DC power supplies. power supply Each power supply supports a full rack of any combination of cards. The redundant power supply can be replaced without affecting system performance Flexibility Single chassis for various modular converters with a variety of technologies, rates, interfaces and media Hot-swappable All cards are hot-swappable and can be replaced without interfering with the modular converters data transmission of other cards High Reliability NEBS Compliant Safety Compliance CE and UL Effcient Heat Optimal structure for effcient heat dissipation dissipation RC004-16NMS1 RC004-16NMS2 RC004-16AC RC004-16DC RC007-2AC RC007-2DC Mount Angle 19 Center Mount Angle 21 Center Master agent module for network management, installed in slot 0 of RC chassis Cascade module for network management, installed in slot 0 of RC chassis 10U, 16-slot chassis with one AC power supply (can provide redundant power supply) 10U, 16-slot chassis with one DC power supply (can provide redundant power supply) Redundant power supply for RC chassis, AC Redundant power supply for RC chassis, DC Accessory for installing RC chassis on 19" center mounted rack Note: RC chassis can be directly installed on normal front mounted 19" rack and need no additioinal mount angle. Accessory for installing RC chassis on 21" center mounted rack RC slot Chassis with SNMP Management RC004-16NMS1 Management Agent Module Specifcation Power supply Input power supply voltage Short Current Protection Dimension Power consumption Working Storage Compliance Standard RC004-16NMS2 Management Cascade Module Two hot-swappable AC or DC power supplies AC: 185V-265V, 50/60Hz DC: -36V- -72V Yes 436(W)*440(H)*360(D)mm 150W (at max load) Temp: 0~50 centigrade RH: 5~90% non-condensing Temp: -40~85 centigrade RH: 20~90% non-condensing UL

9 RC006-1 Series single-slot chassis Raisecom modem pool RC could feed high speed and legacy data service, leased line service and backhauling of mobile BTS and connectivity WiMAX CPE of Metro Ethernet simultaneously. It could hybrid support for multiple levels PDH products including E1 extension PDH fber optical multiplexer, PCM multiplexer, Ethernet over PDH Inverse Multiplexer. All of the module in central offce modem pool RC could be deployed in remote site with single-slot chassis RC006-1 as well to enable customer to save cost for inventory. Raisecom also offers the single-slot chassis with SNMP & console ports RC006-1M for single module application in central offce. RC006-1 RC006-1, RC006-1M s Construction RC006-1 RC006-1M Single-slot, 19 inch, 1Unit high Single AC, or single DC, or AC/DC redundant power supplies non-management chassis SNMP interface for management, Console interface for SNMP initial confguration. In support of management over service modules in the chassis and remote devices In support of online upgrade RC006-1-X single-slot chassis for modules in RC RC006-1M-X single-slot chassis for modules in RC006-12, SNMP management X indicates the optical port specifcation: AC: 220V/230VAC power supply; DC: -48VDC power supply; AC/DC: AC and DC redundant power supply Application Specifcation Console port SNMP port Dimensions Power Consumption Working Safety compliance RC006-1M RS-232 standard RJ bps 10/100Mbps FDX/HDX Auto-negotiation IEEE802.3x fow control Auto-MDI/MDIX 430(W)*44.45(H)*266mm(D) 180VAC~260VAC -36VDC~-72VDC +12VDC~+36VDC <5W (non-managable) <15W (managable) Temp: 0~50 centigrade RH: 5~90% non-condensing CE certifcation Modules Working & Managed in RC006-1M Ethernet to E1 Interface Converter RC956-FE(X)8E1 PDH Fiber Optic Multiplexer RC (-BL),RC (-BL) Multi-Service PDH Multiplexer RCMS FE(-BL),RCMS FE(- BL),RCMS FE,RCMS FE(- BL),RCMS FE(-BL) Voice/Data over E1/Fiber Multiplexer RC3102,RC3202 Optical Line Protection Card for CWDM system OPCOM100-OLP-A RCVS series Video Optical Multiplexer

10 RC service slots multi-service modem pool RC is a ETSI complied 19" rackmountable 6U high platform which supports two front-loading, redundant, load-sharing, hot-swappable AC or DC power supplies. Up to 12 modular service cards and one network management card can be installed in the chassis, providing a CO/POP site solution for connecting up to 12 remote CPE. RC multi-service modem pool feeds simultaneously high speed and legacy data service, analog voice service, leased line service and backhauling of Mobile BTS and connectivity WiMAX CPE to Metro Ethernet. It could hybrid support for multiple level PDH products such as: cost effective E1 extension PDH product up to 16E1; PCM multiplexer s analog voice and legacy data service for enterprise customers; carrier grade multiservice PDH product with up to 16 E1s (including 1*V.35) and 1*10/100M Ethernet interface. Redundant fber optic links and power supply could guarantee the maximum networking uptime. Switching over time from primary fber link to secondary is less than 50ms. This platform could supply SNMP management, TELNET, and local craft terminal management through RS232 interface. Full range of management makes carrier to easily operate and monitor local and remote device anywhere. RC service slots multi-service modem pool Slot Number 15 slots, 12 slots for service cards, 2 slots for power supply modules and 1 slot for network management card Redundant Power Two front-loading, redundant, load-sharing, hot-swappable dual AC or dual Supply DC or one AC and one DC power supply Hot-wappable RC can operate with single or dual AC or DC power supplies. power supply Each power supply supports a full rack of any combination of cards. The redundant power supply can be replaced without affecting system performance Flexibility Single chassis for various modular cards with a variety of technologies, rates, interfaces and media, unifed SNMP management for all the modules Hot-swappable All cards are hot-swappable and can be replaced without interfering with the modular converters data transmission of other cards Safety Compliance CE and UL Effcient Heat Optimal structure for effcient heat dissipation dissipation Network Management Real-time confguration and monitoring The chassis can be managed by Raisecom network management platform Nview iems (GUI), which allowing confguration management, diagnostics and loop activation, as well as monitoring and fault management The management software enables the user to change the setup confguration, get real-time alerts on system status, activate diagnostics, and receive statistics on system functionality in a graphic format. RC NMS RC006-12AC/S RC006-12AC/D RC006-12DC/S RC006-12DC/D Network management module for RC chassis 6U, 12 service slots chassis with one 115V or 230V AC power supply 6U, 12 service slots chassis with two 115V or 230V AC power supplies 6U, 12 service slots chassis with one -48V DC power supply 6U, 12 service slots chassis with two -48V DC power supplies Specifcation Number of slot slots for service cards 2 slots for power supply modules 1 slot for network management card Power supply Two hot-swappable AC or DC power supplies Input power AC: 85V-265V, 50/60Hz supply voltage DC: -36V- -72V Rated Current 20A Short Current Yes Protection Over Current Yes Protection Noise 100mVp-p Port specifcation (For NMS1 network management card) Net Weight Dimension Power consumption Working Storage CONSOLE: RJ-45 ETH (for SNMP and Telnet): RJ kg (with two power supplies) 442(W)*248(H)*267(D)mm 300W (at max load) Temp: -5~50 centigrade RH: 5~90% non-condensing Temp: -40~85 centigrade RH: 20~90% non-condensing

11 Typical Applicatioin